Comparison of the n-Alkanes and Polycyclic Aromatic Hydrocarbons Concentrations in the Atmosphere during the Preparation of Warm and Hot Mixtures Asphalt for Pavements

Asphalt binder is used in the production of hot mixes asphalt (HMA) for paving and, due to the high temperatures used, generates fumes thatcontainn-alkanes and polycyclic aromatic hydrocarbons (PAH). Asphalt mixes prepared at lower temperatures, such as warm mixes asphalt (WMA), may contribute to reduce the emissions of those compounds and save energy. This paper investigatesn-alkanes and PAH in the total suspended particles during the preparation of WMA, in comparison with HMA, in laboratory. The results showed that the n-alkanes of the WMA and HMA presented C-max at n-C-26 and n-C-28, respectively; also, the total content of n-alkanes was higher for the HMA than forthe WMA. Besides, benzo[b]fluoranthene and benzo[a]anthracene were the major PAH in the WMA, while the higher temperatures of the HMA were observed to volatilize all larger PAH, demonstrating higher potential of inhalation exposure.

Cuticular Hydrocarbons Discriminate Distinct Colonies of Melipona marginata (Hymenoptera, Apinae, Meliponini)

The aim of the present study was to characterize the variation of the chemical profiles among workers in different colonies of the stingless bee Melipona marginata. We used gas chromatography and mass spectrometry (CG-MS) and multivariate analysis of the bees' chemical from three colonies of two localities in southeast Brazil. The results showed that cuticular hydrocarbon profiles clearly separated distinct colonies. We show here the importance of using the chemical analyses for characterization of colony membership, in addition of the traditional techniques of diversity analyses.

Genotoxicity assessment of water soluble fractions of biodiesel and its diesel blends using the Salmonella assay and the in vitro MicroFlow (R) kit (Litron) assay

The designation of biodiesel as an environmental-friendly alternative to diesel oil has improved its commercialization and use. However, most biodiesel environmental safety studies refer to air pollution and so far there have been very few literature data about its impacts upon other biotic systems, e.g. water, and exposed organisms. Spill simulations in water were carried out with neat diesel and biodiesel and their blends aiming at assessing their genotoxic potentials should there be contaminations of water systems. The water soluble fractions (WSF) from the spill simulations were submitted to solid phase extraction with C-18 cartridge and the extracts obtained were evaluated carrying out genotoxic and mutagenic bioassays [the Salmonella assay and the in vitro MicroFlow (R) kit (Litron) assay]. Mutagenic and genotoxic effects were observed, respectively, in the Salmonella/microsome preincubation assay and the in vitro MN test carried out with the biodiesel WSF. This interesting result may be related to the presence of pollutants in biodiesel derived from the raw material source used in its production chain. The data showed that care while using biodiesel should be taken to avoid harmful effects on living organisms in cases of water pollution. (C) 2011 Elsevier Ltd. All rights reserved.

Comparison of the n-alkanes and polycyclic aromatic hydrocarbons concentrations in the atmosphere during the preparation of warm and hot mixtures asphalt for pavements

O asfalto é utilizado na produção de misturas asfálticas a quente (HMA) para a pavimentação e, devido às altas temperaturas empregadas, gera fumos que contêm n-alcanos e hidrocarbonetos policíclicos aromáticos (HPAs). As misturas asfálticas preparadas em temperaturas mais baixas, como as misturas asfálticas mornas (WMA), podem contribuir na redução das emissões daqueles compostos e economizar energia. Este trabalho investiga os n-alcanos e os HPAs nas partículas totais em suspensão durante a preparação de uma WMA, em comparação com uma HMA, em laboratório. Os resultados mostraram que os n-alcanos da WMA e da HMA apresentaram Cmáx no n-C26 e n-C28, respectivamente, e o teor de n-alcanos total foi maior na HMA do que na WMA. Ademais, verificou-se que o benzo[b]fluoranteno e benzo[a]antraceno constituíam os maiores HPAs na WMA, enquanto as temperaturas mais altas da HMA volatilizaram todos seus grandes HPAs, demonstrando maior potencial de exposição por inalação.

Management practices and influences on IT architecture decisions: a case study in a telecom company

The study aims to analyze the IT architecture management practices associated with their degree of maturity and the influence of institutional and strategic factors on the decisions involved through a case study in a large telecom organization. The case study allowed us to identify practices that led the company to its current stage of maturity and identify practices that can lead the company to the next stage. The strategic influence was mentioned by most respondents and the institutional influence was present in decisions related to innovation and those dealing with a higher level of uncertainties.

Chemical Bonding of Hydrocarbons to Metal Surfaces

Using x-ray absorption spectroscopy (XAS), x-ray emission spectroscopy (XES) and x-ray photoelectron spectroscopy (XPS) in combination with density functional theory (DFT) the changes in electronic and geometric structure of hydrocarbons upon adsorption are determined. The chemical bonding is analyzed and the results provide new insights in the mechanisms responsible for dehydrogenation in heterogeneous catalysis. In the case of alkanes, n-octane and methane are studied. XAS and XES show significant changes in the electronic structure upon adsorption. XES shows new adsorption induced occupied states and XAS shows quenching of CH*/Rydberg states in n-octane. In methane the symmetry forbidden gas phase lowest unoccupied molecular orbital becomes allowed due to broken symmetry. New adsorption induced unoccupied features with mainly metal character appear just above the Fermi level in XA spectra of both adsorbed methane and n-octane. These changes are not observed in DFT total energy geometry optimizations. Comparison between experimental and computed spectra for different adsorbate geometries reveals that the molecular structures are significantly changed in both molecules. The C-C bonds in n-octane are shortened upon adsorption and the C-H bonds are elongated in both n-octane and methane. In addition ethylene and acetylene are studied as model systems for unsaturated hydrocarbons. The validity of both the Dewar-Chatt-Duncanson chemisorption model and the alternative spin-uncoupling picture is confirmed, as well as C-C bond elongation and upward bending of the C-H bonds. The bonding of ethylene to Cu(110) and Ni(110) are compared and the results show that the main difference is the amount of back-donation into the molecular π* orbital, which allows the molecule to desorb molecularly from the Cu(110) surface, whereas it is dehydrogenated upon heating on the Ni(110) surface. Acetylene is found to adsorb in two different adsorption sites on the Cu(110) surface at liquid nitrogen temperature. Upon heating the molecules move into one of these sites due to attractive adsorbate-adsorbate interaction and only one adsorbed species is present at room temperature, at which point the molecules start reacting to form benzene. The bonding of the two species is very similar in both sites and the carbon atoms are rehybridized essentially to sp2.

Influence of alternative electron acceptors on the anaerobic biodegradation of polycyclic aromatic hydrocarbons

Polycyclic aromatic hydrocarbons are chemicals produced by both human activities and natural sources and they have been present in the biosphere since millions of years. For this reason microorganisms should have developed, during the world history, the capacity of metabolized them under different electron acceptors and redox conditions. The deep understanding of these natural attenuation processes and of microbial degradation pathways has a main importance in the cleanup of contaminated areas. Anaerobic degradation of aromatic hydrocarbons is often presumed to be slow and of a minor ecological significance compared with the aerobic processes; however anaerobic bioremediation may play a key role in the transformation of organic pollutants when oxygen demand exceeds supply in natural environments. Under such conditions, anoxic and anaerobic degradation mediated by denitrifying or sulphate-reducing bacteria can become a key pathway for the contaminated lands clean up. Actually not much is known about anaerobic bioremediation processes. Anaerobic biodegrading techniques may be really interesting for the future, because they give the possibility of treating contaminated soil directly in their natural status, decreasing the costs concerning the oxygen supply, which usually are the highest ones, and about soil excavations and transports in appropriate sites for a further disposal. The aim of this dissertation work is to characterize the conditions favouring the anaerobic degradation of polycyclic aromatic hydrocarbons. Special focus will be given to the assessment of the various AEA efficiency, the characterization of degradation performance and rates under different redox conditions as well as toxicity monitoring. A comparison with aerobic and anaerobic degradation concerning the same contaminated material is also made to estimate the different biodegradation times.

New discotic liquid crystals based on large polycyclic aromatic hydrocarbons as materials for molecular electronics

A series of new columnar discotic liquid crystalline materials based on the superphenalene (C96) core has been synthesized by oxidative cyclodehydrogenation with iron(III) chloride of suitable three-dimensional oligophenylene precursors. These compounds were investigated by means of differential scanning calorimetry (DSC), polarized optical microscopy (POM) and wide angle X-ray scattering (WAXS), and showed highly ordered supramolecular arrays and mesophase behavior over a broad temperature range. Good solubility, through the introduction of long alkyl chains, and the fact that these new superphenalene derivatives were found to be liquid crystalline at room temperature enabled the formation of highly ordered films (using the zone-casting technique), a requirement for application in organic electronic devices. The one-dimensional, intracolumnar charge carrier mobilities of superphenalene derivatives were determined using the pulse-radiolysis time-resolved microwave conductivity technique (PR-TRMC). Electrical properties of different C96-C12 architectures on mica surfaces were examined by using Electrostatic Force Microscopy (EFM) and Kelvin Probe Force Microscopy (KPFM). Hexa-peri-hexabenzocoronene (C42) derivatives substituted at the periphery with six branched alkyl ether chains were also synthesized. It was found that the introduction of ether groups within the side chains enhances the affinity of the discotic molecules towards polar surfaces, resulting in homeotropic self-assembly (as shown by POM and 2D-WAXS) when the compounds are processed from the isotropic state between two surfaces. A new, insoluble, superphenalene building block bearing six reactive sites was prepared, and was further used for the preparation of dendronized superphenalenes with bulky dendritic substituents around the core. UV/Vis and fluorescence experiments suggest reduced π-π stacking of the superphenalene cores as a result of steric hindrance between the peripheral dendritic units. A new family of graphitic molecules with partial ”zig-zag” periphery has been established. The incorporation of ”zig-zag” edges was shown to have a strong influence on the electronic properties of the new molecules (as studied by solution and solid-state UV/Vis, and fluorescence spectroscopy), leading to a significant bathochromic shift with respect to the parent PAHs (C42 and C96). The reactivity of the additional double bonds was examined. The attachment of long alkyl chains to a ”zig-zag” superphenalene core afforded a new, processable, liquid crystalline material.

Control of the long-range self-organization of polycyclic aromatic hydrocarbons for device applications

Electronic devices based on organic semiconductors have gained increased attention in nanotechnology, especially applicable to the field of field-effect transistors and photovoltaic. A promising class of materials in this reseach field are polycyclic aromatic hydrocarbons (PAHs). Alkyl substitution of these graphenes results in the selforganization into one-dimensional columnar superstructures and provides solubility and processibility. The nano-phase separation between the π-stacking aromatic cores and the disordered peripheral alkyl chains leads to the formation of thermotropic mesophases. Hexa-peri-hexabenzocoronenes (HBC), as an example for a PAH, exhibits some of the highest values for the charge carrier mobility for mesogens, which makes them promising candidates for electronic devices. Prerequisites for efficient charge carrier transport between electrodes are a high purity of the material to reduce possible trapping sites for charge carriers and a pronounced and defect-free, long-range order. Appropriate processing techniques are required to induce a high degree of aligned structures in the discotic material over macroscopic dimensions. Highly-ordered supramolecular structures of different discotics, in particular, of HBC derivatives have been obtained by solution processing using the zone-casting technique, zone-melting or simple extrusion. Simplicity and fabrication of highly oriented columnar structures over long-range are the most essential advantages of these zone-processing methods. A close relation between the molecular design, self-aggregation and the processing conditions has been revealed. The long-range order achieved by the zone-casting proved to be suitable for field effect transistors (FET).

Synthetical engineering of supramolecular properties of large polycyclic aromatic hydrocarbons

An important property for devices is the charge-carrier mobility values for discotic organic materials like hexa-peri-hexabenzocoronenes. A close relation exists between the degree of their columnar self-arrangement of the molecules and their mobilities. Within this first step an induction of a higher order via hydrogen-bonding was considered, which mainly pointed towards the improvement of the intracolumnar stacking of the materials. For the analytics a broad range of methods was used including differential scanning calorimetry (DSC), wide-angle X-ray diffractometry (WAXS), solid-state NMR spectroscopy and scanning tunneling microscopy (STM). Indeed, a specific influence of the hydrogen-bonds could be identified, although in several cases by the cost of a severe reduction of solubility and processability. This effect was dampened by the addition of a long alkyl chain next to the hydrogen-bond exerting functional group, which resulted in an improved columnar arrangement by retention of processability. In contrast to the before mentioned example of inducing a higher intracolumnar order by hydrogen-bonding, the focus was also be set upon larger aromatic systems. The charge-carrier mobility is also in close relation to the size of the aromatic core and larger π-areas are expected to lead to improved mobilities. For photovoltaic applications a high extinction coefficient over a broad range of the spectrum is favorable, which can also be achieved by enlarging the aromatic core component. In addition the stronger π-interactions between the aromatic core components should yield an improved columnar stability and order. However the strengthening of the π-interactions between the aromatic core components led to a reduction of the solubility and the processability due to the stronger aggregation of the molecules. This required the introduction of efficiently solubilizing features in terms of long alkyl chains in the corona of the aromatic entity, in combination of a distortion of the aromatic core moiety by bulky tert-butyl groups. By this approach not only the processing and cleaning of the materials with standard laboratory techniques became possible, but moreover the first structure-rich UV/vis and a resolved 1H-NMR spectra for an aromatic system two times larger than hexa-peri-hexabenzocoronene were recorded. The bulk properties in an extruded fiber as well as on the surface showed a columnar self-assembly including a phase in which a homeotropic alignment on a substrate was observed, which turns the material into an interesting candidate for future applications in electronic devices.

Synthesis and characterization of new discotic polycyclic aromatic hydrocarbons and related pyrolytic nanostructures

Diskotische Hexa-peri-hexabenzocoronene (HBC) als molekulare, definierte graphitische Substrukturen sind bereits seit langem Gegenstand von Untersuchungen zu der Delokalisierung von π-Elektronen. In dieser Arbeit wurden zusätzlich Platin-Komplexe in das periphere Substitutionsmuster von HBC eingeführt. Dies führte zu einer Verbesserung der Emission von dem angeregten Triplett-Zustand in den Singulett-Grundzustand mit einer zusätzlichen Verlängerung der Lebensdauer des angeregten Zustandes. Zusätzlich erlaubte diese Konfiguration ein schnelles Intersystem-Crossing mittels einer verstärkten Spin-Orbit Kopplung, die sowohl bei tiefen Temperaturen, als auch bei Raumtemperatur exklusiv zu Phosphoreszenz (T1→S0) führte. Das Verständniss über solche Prozesse ist auch essentiell für die Entwicklung verbesserter opto-elektronischer Bauteile. Die Erstellung von exakt definierten molekularen Strukturen, die speziell für spezifische Interaktionen hergestellt wurden, machten eine Inkorporation von hydrophoben-hydrophilen, wasserstoffverbrückten oder elektrostatischen funktionalisierten Einheiten notwendig, um damit den supramolekularen Aufbau zu kontrollieren. Mit Imidazolium-Salzen funktionalisierte HBC Derivate wurden zu diesem Zwecke hergestellt. Eine interessante Eigenschaft dieser Moleküle ist ihre Amphiphilie. Dies gestattete die Untersuchung ihrer Eigenschaften in einem polaren Solvens und sowohl der Prozessierbarkeit als auch der Faserbildung auf Siliziumoxid-Trägern. Abhängig vom Lösungsmittel und der gewählten Konditionen konnten hochkristalline Fasern erhalten werden. Durch eine Substitution der HBCs mit langen, sterisch anspruchsvollen Seitenketten, konnte durch eine geeignete Prozessierung eine homöotrope Ausrichtung auf Substraten erreicht werden, was dieses Material interessant für photovoltaische Applikationen macht. Neuartige Polyphenylen-Metall-Komplexe mit diskotischen, linearen und dendritischen Geometrien wurden mittels einer einfachen Reaktion zwischen Co2(CO)8 und Ethinyl-Funktionalitäten in Dichlormethan hergestellt. Nach der Pyrolyse dieser Komplexe ergaben sich unterschiedliche Kohlenstoff-Nanopartikel, inklusive Nanoröhren, graphitischen Nanostäben und Kohlenstoff/Metall Hybrid Komplexe, die durch Elektronenmikroskopie untersucht wurden. Die resultierenden Strukturen waren dabei abhängig von der Zusammensetzung und Struktur der Ausgangssubstanzen. Anhand dieser Resultate ergeben sich diverse Möglichkeiten, um den Mechanismus, der zur Herstellung graphitischer Nanopartikel führt, besser zu verstehen.