Growth and demise of Permian biogenic chert along northwest Pangea: evidence for end-Permian collapse of thermohaline circulation

The Permian Chert Event (PCE) was a 30 Ma long episode of unusual chert accumulation along the northwest margin of Pangea, and possibly worldwide. The onset of the PCE occurred at about the Sakmarian-Artinskian boundary in the Sverdrup Basin, Canadian Arctic, where it coincides with a maximum flooding event, the ending of high-frequency/high-amplitude shelf cyclicity, the onset of massive biogenic chert deposition in deep-water distal areas, and a long-term shift from warm- to cool-water carbonate sedimentation in shallow-water proximal areas. A similar and coeval shift is observed from the Barents Sea to the northwestern USA. A landward and southward expansion of silica factories occurred during the Middle and Late Permian at which time warm-water carbonate producers disappeared completely from the northwest margin of Pangea. Biotically impoverished and increasingly narrow cold-water carbonate factories (characterised by non-cemented bioclasts of sponges, bryozoans, echinoderms and brachiopods) were then progressively replaced by silica factories. By Late Permian time, little carbonate sediments accumulated in the Barents Sea and in the Sverdrup Basin. where the deep- to shallow-water sedimentary spectrum was occupied by siliceous sponge spicules. By that time, biogenic silica sedimentation was common throughout the world. Silica factories collapsed in the Late Permian, abruptly bringing the PCE to an end. In northwest Pangea, the end- Permian collapse of the PCE was associated with a major transgression and with a return to much warmer oceanic and continental climatic conditions. Chert deposition resumed in the distal oceanic areas during the early Middle Triassic (Anisian) after a 8-10 Ma interruption (Early Triassic Chert Gap). The conditions necessary for the onset, expansion and zenith of the PCE were provided by the thermohaline circulation of nutrient-rich cold waters along the northwestern and western margin of Pangea, and possibly throughout the world oceans. These conditions provided an efficient transportation mechanism that constantly replenished the supply of silica in the area, created a nutrient- and oxygen-rich environment favouring siliceous biogenic productivity. established cold sea-floor conditions, hindering silica dissolution, while increasing calcium carbonate solubility, and provided conditions adverse to organic and inorganic carbonate production, The northwest margin of Pangea was, for nearly 30 Ma. bathed by cold waters presumably derived from the seasonal melting of northern sea ice, the assumed engine for thermohaline circulation. This process started near the Sakmarian-Artinskian boundary. intensified throughout Middle and Late Permian time and ceased suddenly in latest Permian time, It led to oceanic conditions much colder than normally expected from the palaeolatitudes. and the influence of cold northerly-derived water was felt as far south southern Nevada. The demise of silica factories was caused by the rapid breakdown of these conditions and the establishment of a much warmer marine environment accompanied by sluggish circulation and perhaps a reduced input of dissolved silica to the ocean. Complete thawing of northern sea ice would have ended thermohaline circulation and led to warm and sluggish oceanic conditions inimical to the production. accumulation and preservation of biogenic silica.

Designing Digital Filters for Servo Systems

The aim of this work was to select an appropriate digital filter for a servo application and to filter the noise from the measurement devices. Low pass filter attenuates the high frequency noise beyond the specified cut-off frequency. Digital lowpass filters in both IIR and FIR responses were designed and experimentally compared to understand their characteristics from the corresponding step responses of the system. Kaiser Windowing and Equiripple methods were selected for FIR response, whereas Butterworth, Chebyshev, InverseChebyshev and Elliptic methods were designed for IIR case. Limitations in digital filter design for a servo system were analysed. Especially the dynamic influences of each designed filter on the control stabilityof the electrical servo drive were observed. The criterion for the selection ofparameters in designing digital filters for servo systems was studied. Control system dynamics was given significant importance and the use of FIR and IIR responses in different situations were compared to justify the selection of suitableresponse in each case. The software used in the filter design was MatLab/Simulink® and dSPACE's DSP application. A speed controlled Permanent Magnet Linear synchronous Motor was used in the experimental work.

Kylmämuokatun austeniittisen ruostumattoman teräsputkipalkin hitsaus

Diplomityön tavoitteena on selvittää kylmälujitetusta austeniittisesta ruostumattomasta teräksestä valmistettavan putkipalkin pituussuunnassa hitsaamalla tapahtuvaa valmistusta. Työssä tarkastellaan eri hitsausprosessien lämmöntuonnin ja putkipalkin kylmämuovaamalla tapahtuvan valmistuksen ja hitsin jälkikäsittelynvaikutuksia putkipalkin pituushitsin mekaanisiin ominaisuuksiin. Teoriaosassa on perehdytty austeniittisen ruostumattoman teräksen hitsaukseen, kylmämuokkaamalla lujitetun teräksen käyttäytymiseen hitsauksessa, monipoltinkaari-, TIG-suurtaajuuspulssi- ja kaariavusteiseen laserhitsaukseen. Kokeellisessa osassaon suoritettu koehitsauksia edellä mainituilla menetelmillä kylmälujitetulle austeniittiselle ruostumattomalle teräkselle ja suoritettu saatujen koehitsien mekaanisien ominaisuuksien arviointia. Saatujen koetulosten perusteella ontodettu, että huolimatta hitsauksen lämmöntuonnin kylmämuokatun teräksen lujuusarvoja alentavasta vaikutuksesta on mahdollista valmistaa hitsin osalta perusaineen lujuusluokituksen täyttäviä putkipalkkeja. Tämä johtuu putkipalkin kylmämuovaamalla tapahtuvan valmistuksen ja hitsin jälkikäsittelyn hitsauksessa pehmentyneen vyöhykkeen lujuusarvoja takaisin perusaineen tasolle palauttavasta vaikutuksesta.

Methylation of CpG island promoters in uveal melanoma.

BACKGROUND: Inactivation of tumour-related genes by promoter hypermethylation is a common epigenetic event in the development of a variety of tumours. AIM: To investigate in primary uveal melanoma the status of promoter methylation of genes thought to be involved in tumour development: p16, TIMP3, RASSF1, RARB, FHIT, hTERT and APC. METHODS: Gene promoter methylation was studied by methylation-sensitive single-strand conformation analysis and dot-blot assay in a series of 23 primary uveal melanomas. All DNA samples were obtained from paraffin-embedded formalin-fixed tissue blocks. RESULTS: hTERT promoter methylation was found with a relatively high frequency (52%). Promoter methylation of p16, TIMP3, RASSF1, RARB, FHIT and APC was a rare event. For none of these genes did promoter methylation exceed 15% of tumour samples, and, for some genes (FHIT and APC), no methylation was found at all. Furthermore, promoter methylation was absent in 39% (9/23) of cases. In only 22% (5/23) of cases was hypermethylation of at least two promoters observed. CONCLUSIONS: Promoter methylation of hTERT is a regular event in uveal melanoma. Hypermethylation of the other genes studied does not seem to be an essential element in the development of this tumour. As promoter methylation of APC, RASSF1 and RARB is often observed in cutaneous melanoma, these results suggest that different epigenetic events occur in the development of cutaneous and uveal melanoma.

Koivun HFV-kuivauksen kustannusvaikutukset

Työn tavoitteena on ollut selvittää HFV-kuivauksen taloudellisia vaikutuksia, kuivausmenetelmän toimintaperiaatteita, ominaisuuksia ja Lahden ammattikorkeakoulun Tekniikan laitoksen kuivaustutkimuksesta saatuja tuloksia. Tutkimuskohteeksi on valittu sydänkeskeinen koivu, joka soveltuu erinomaisesti uuden kuivausmenetelmän raaka-aineeksi, sillä sen hankintakustannukset muodostuvat tavanomaista koivusahatavaraa alhaisemmaksi ja sillä saavutetaan raaka-aineen jatkojalostusarvon huomattava nousu. Työn teoriaosassa on käsitelty puun kuivausta, sen yleisiä piirteitä ja erikuivausvaihtoehtoja. Koivun kuivauksesta ja kuivauskustannuksista löytyy varsinvähän julkaistua tutkimustietoa, jonka johdosta kuivauskustannuksia kartoitettiin myös kotimaisten havupuiden osalta. Tuoreen koivun kuivaus muutamassa tunnissa puusepänkuivaksi aihioksi ilman kuivausvirheitä on Lahden ammattikorkeakoulun Tekniikan laitoksen tutkimuksissa saatujen tuloksien mukaan mahdollista. Tässä tutkimuksessa on käsitelty neljän eri teholuokan kuivaamoinvestointivaihtoehtoa. Vaihtoehdot poikkeavat toisistaan niin hankintahinnan, tuotantokapasiteetin kuinvalmistuskustannuksienkin suhteen. Mikäli kuivaamon tuotantokapasiteetti ei olemääräävä tekijä ja investoinnilla ei ole pääomarajoitetta, niin kannattavimmaksi investointivaihtoehdoksi osoittautuu suurimman kokoluokan HFV-kuivaamolaitteisto.

Blood-Borne Circadian Signal Stimulates Daily Oscillations in Actin Dynamics and SRF Activity.

In peripheral tissues circadian gene expression can be driven either by local oscillators or by cyclic systemic cues controlled by the master clock in the brain's suprachiasmatic nucleus. In the latter case, systemic signals can activate immediate early transcription factors (IETFs) and thereby control rhythmic transcription. In order to identify IETFs induced by diurnal blood-borne signals, we developed an unbiased experimental strategy, dubbed Synthetic TAndem Repeat PROMoter (STAR-PROM) screening. This technique relies on the observation that most transcription factor binding sites exist at a relatively high frequency in random DNA sequences. Using STAR-PROM we identified serum response factor (SRF) as an IETF responding to oscillating signaling proteins present in human and rodent sera. Our data suggest that in mouse liver SRF is regulated via dramatic diurnal changes of actin dynamics, leading to the rhythmic translocation of the SRF coactivator Myocardin-related transcription factor-B (MRTF-B) into the nucleus.

Alcohol consumption and binge drinking in young adult childhood cancer survivors.

BACKGROUND: This study compared frequency of alcohol consumption and binge drinking between young adult childhood cancer survivors and the general population in Switzerland, and assessed its socio-demographic and clinical determinants. PROCEDURE: Childhood cancer survivors aged <16 years when diagnosed 1976-2003, who had survived >5 years and were currently aged 20-40 years received a postal questionnaire. Reported frequency of alcohol use and of binge drinking were compared to the Swiss Health Survey, a representative general population survey. Determinants of frequent alcohol consumption and binge drinking were assessed in a multivariable logistic regression. RESULTS: Of 1,697 eligible survivors, 1,447 could be contacted and 1,049 (73%) responded. Survivors reported more often than controls to consume alcohol frequently (OR = 1.7; 95%CI = 1.3-2.1) and to engage in binge drinking (OR = 2.9; 95%CI = 2.3-3.8). Peak frequency of binge drinking in males occurred at age 24-26 years in survivors, compared to age 18-20 in the general population. Socio-demographic factors (male gender, high educational attainment, French and Italian speaking, and migration background from Northern European countries) were most strongly associated with alcohol consumption patterns among both survivors and controls. CONCLUSIONS: The high frequency of alcohol consumption found in this study is a matter of concern. Our data suggest that survivors should be better informed on the health effects of alcohol consumption during routine follow-up, and that such counseling should be included in clinical guidelines. Future research should study motives of alcohol consumption among survivors to allow development of targeted health interventions for this vulnerable group.

Interplays between mouse mammary tumor virus and the cellular and humoral immune response.

Mouse mammary tumor virus has developed strategies to exploit the immune response. It requires vigorous immune stimulation to achieve efficient infection. The infected antigen-presenting cells present a viral superantigen on the cell surface which stimulates strong CD4-mediated T-cell help but CD8 T-cell responses are undetectable. Despite the high frequency of superantigen-reactive T cells, the superantigen-induced immune response is comparable to classical antigen responses in terms of T-cell priming, T-cell-B-cell collaboration as well as follicular and extra-follicular B-cell differentiation. Induction of systemic anergy is observed, similar to classical antigen responses where antigen is administered systemically but does not influence the role of the superantigen-reactive T cells in the maintenance of the chronic germinal center reaction. So far we have been unable to detect a cytotoxic T-cell response to mouse mammary tumor virus peptide antigens or to the superantigen. This might yet represent another step in the viral infection strategy.

Improving Dynamic Characteristics of Open-loop Controlled Log Crane

The improvement of the dynamics of flexible manipulators like log cranes often requires advanced control methods. This thesis discusses the vibration problems in the cranes used in commercial forestry machines. Two control methods, adaptive filtering and semi-active damping, are presented. The adaptive filter uses a part of the lowest natural frequency of the crane as a filtering frequency. The payload estimation algorithm, filtering of control signal and algorithm for calculation of the lowest natural frequency of the crane are presented. The semi-active damping method is basedon pressure feedback. The pressure vibration, scaled with suitable gain, is added to the control signal of the valve of the lift cylinder to suppress vibrations. The adaptive filter cuts off high frequency impulses coming from the operatorand semi-active damping suppresses the crane?s oscillation, which is often caused by some external disturbance. In field tests performed on the crane, a correctly tuned (25 % tuning) adaptive filter reduced pressure vibration by 14-17 % and semi-active damping correspondingly by 21-43%. Applying of these methods require auxiliary transducers, installed in specific points in the crane, and electronically controlled directional control valves.

Applicability of Power-Line Communications to Data Transfer of On-line Condition Monitoring of Electrical Drives

The research of power-line communications has been concentrated on home automation, broadband indoor communications and broadband data transfer in a low voltage distribution network between home andtransformer station. There has not been carried out much research work that is focused on the high frequency characteristics of industrial low voltage distribution networks. The industrial low voltage distribution network may be utilised as a communication channel to data transfer required by the on-line condition monitoring of electric motors. The advantage of using power-line data transfer is that it does not require the installing of new cables. In the first part of this work, the characteristics of industrial low voltage distribution network components and the pilot distribution network are measured and modelled with respect topower-line communications frequencies up to 30 MHz. The distributed inductances, capacitances and attenuation of MCMK type low voltage power cables are measured in the frequency band 100 kHz - 30 MHz and an attenuation formula for the cables is formed based on the measurements. The input impedances of electric motors (15-250 kW) are measured using several signal couplings and measurement based input impedance model for electric motor with a slotted stator is formed. The model is designed for the frequency band 10 kHz - 30 MHz. Next, the effect of DC (direct current) voltage link inverter on power line data transfer is briefly analysed. Finally, a pilot distribution network is formed and signal attenuation in communication channels in the pilot environment is measured. The results are compared with the simulations that are carried out utilising the developed models and measured parameters for cables and motors. In the second part of this work, a narrowband power-line data transfer system is developed for the data transfer ofon-line condition monitoring of electric motors. It is developed using standardintegrated circuits. The system is tested in the pilot environment and the applicability of the system for the data transfer required by the on-line condition monitoring of electric motors is analysed.

Associations of baroreflex sensitivity, heart rate variability, and initial orthostatic hypotension with prenatal and recent postnatal methylmercury exposure in the Seychelles Child Development Study at age 19 years.

BACKGROUND: A few studies have suggested an association between prenatal exposure to methylmercury and decreased heart rate variability (HRV) related to autonomic heart function, but no study has examined this association using baroreflex sensitivity (BRS). In this study we assessed the distribution of BRS and immediate orthostatic hypotension (IOH) in young Seychellois adults and their associations with exposure to prenatal and recent postnatal methylmercury. METHODS: Subjects in the Seychelles Child Development Study (SCDS) main cohort were evaluated at age 19 years. Non-invasive beat-to-beat blood pressure (BP) monitoring (Finapres, Ohmeda) was performed at rest and during active standing in 95 consecutive subjects. Recent postnatal mercury exposure was measured in subjects' hair at the age of 19 years and prenatal exposure in maternal hair grown during pregnancy. BRS was estimated by sequence analysis to identify spontaneous ascending and descending BP ramps. HRV was estimated by the following markers: PNN50 (relative numbers of normal-to-normal intervals which are shorter by more than 50 ms than the immediately following normal-to-normal intervals); rMSSD (root mean of the squared sum of successive interval differences); LF/HF (low frequency/high frequency component ratio); ratio of the mean expiratory/inspiratory RR intervals (EI ratio); and the ratio between the longest RR interval 30 s after active standing and the shortest RR interval at 15 s (Max30/Min15). IOH was estimated by the deepest BP fall within the first 15 s after active standing up. RESULTS: Prenatal MeHg exposures were similar in boys and girls (6.7±4.3, 6.7±3.8 ng/g) but recent postnatal mercury levels were higher in males than females (11.2±5.8 vs 7.9±4.3 ng/g, p=0.003). Markers of autonomic heart rate control were within the normal range (BRS: 24.8±7 ms/mm Hg, PNN50: 24.9±6.8%, rMSSD: 68±22, LF/HF: 0.61±0.28) in both sexes. After standing, 51.4% of subjects had a transient systolic BP drop>40 mm Hg, but only 5.3% reported dizziness or had syncope. Prenatal and recent postnatal MeHg levels, overall, were not associated with BRS, E/I ratio, PNN50, rMSSD, LF/HF ratio, Max30/Min15 ratio, and IOH. CONCLUSIONS: This study provides no support for the hypothesis that prenatal or recent postnatal MeHg exposure from fish consumption is associated with impaired autonomic heart rate control.

Ruostumattoman teräksen TIG-hitsauksen hitsausnopeuden lisääminen

Diplomityön tavoitteena oli ruostumattoman teräksen koneellisen TIG-hitsauksen hitsausnopeuden lisääminen. Työssä tutkittiin suojakaasun koostumuksen vaikutusta hitsausnopeuteen sekä kahta uudehkoa prosessivariaatiota. Tutkitut prosessit olivat TIG-suurtaajuuspulssihitsaus sekä kaksoiskaasu-TIG-hitsaus. Kirjallisessa osassa perehdyttiin TIG-hitsauksen prosessiparametreihin ja -variaatioihin. Kokeellisessa osassa suoritettiin koehitsauksia hitsausnopeuksien selvittämiseksi. Tavoitteena oli tunkeuman kasvattaminen, mikä mahdollistaa hitsausnopeuden noston läpihitsattaessa. Suojakaasuina käytettiin sekä argonpohjaisia että heliumpohjaisia kaasuja, joihin oli lisätty vetyä. Vedyn avulla hitsausnopeus lisääntyi nykykäytäntöä suuremmillakin pitoisuuksilla. Uutena ilmiönä TIG-hitsauksessa havaittiin keyholen eli lävistysreiän syntyminen korkeita vetypitoisuuksia heliumpohjaisessa suojakaasussa käytettäessä. Keyhole oli kuitenkin erittäin epävakaa, joten jatkotutkimuksien tehtäväksi jää selvittää tarkemmin tämän ilmiön vaikutus. Tutkittuihin prosessivariaatioihin todettiin liittyvän useita laiteteknisiä ongelmia. Hitsausnopeuden suhteen tulokset jäivät vaatimattomiksi. Lähinnä keyholen aukaisemisessa ja aukipitämisessä menetelmistä havaittu hyöty antaa selvän aiheen jatkotutkimuksille.

Immersioultraäänitutkimuksen kehittäminen

Teräksenvalmistajilta edellytetään jatkuvasti panostusta laadun ja laadunvarmistuksen kehittämiseen. Teräksen laatu ja puhtaus korostuvat varsinkin silloin, kun terästä käytetään vaativiin käyttökohteisiin, kuten autoteollisuuden tarpeisiin. Ultraäänitarkastusmenetelmää käytetään laadun-varmistuksessa teräksen sisävikojen etsimiseen. Ultraäänitarkastuksessa lähetetään suuritaajuuksista ääntä kappaleeseen. Ääni etenee materiaalissa ja heijastuu erilaisista epäjatkuvuuskohdista. Luotaimeen palaavaa ääntä analysoimalla saadaan tietoa teräksestä ja sen sisävioista. Ultraäänitarkastuksen ongelmana on vian tyypin määrittäminen hankaluus sekä herkkyys tutkittavan materiaalin aineominaisuuksille. Työn tavoitteena oli immersioultraäänitarkastuksen kehittäminen sovellettuna teräksenvalmistajan tarpeisiin. Materiaalin aineominaisuuksista tutkittiin seostuksen vaikutusta. Teräslajit tarkastettiin valssitilaisena, karkaistuna ja normalisoituna. Lisäksi tutkittiin kappaleen pinnankarheuden ja -muodon vaikutusta tarkastukseen. Vikatyyppien tunnistamisen mahdollisuuksia ultra-äänitarkastuksessa selvitettiin käyttäen FFT- taajuusanalyysiä. Erilailla lämpökäsitellyillä teräslajeilla näytti eniten tuloksiin vaikuttavan terästen raekoko. Valssitilaisilla teräksillä raekoko on suuri, jolloin ultraääni vaimenee voimakkaasti teräksessä. Huomattavaa kuitenkin oli, että mikäli lämpö-käsittelyillä ei teräksen raekokoa saada juuri pienennettyä, ei myöskään vaimeneminen vähene. Tämän vuoksi lämpökäsittely ei välttämättä ole aina tarpeellinen valmisteltaessa ultraääninäytteitä. Fourier’n taajuusanalyysissä huomattiin olevan eroavaisuuksia verrattaessa huokosista ja sulkeumista palaavien kaikujen taajuusspektrejä. Näiden tulosten perusteella näyttäisi olevan mahdollista käyttää FFT- menetelmää ultraääni-tarkastuksessa vikojen luokitteluun.

The increase in hydric volume is associated to contractile impairment in the calf after the world's most extreme mountain ultra-marathon

BACKGROUND: Studies have recently focused on the effect of running a mountain ultra-marathon (MUM) and their results show muscular inflammation, damage and force loss. However, the link between peripheral oedema and muscle force loss is not really established. We tested the hypothesis that, after a MUM, lower leg muscles' swelling could be associated with muscle force loss. The knee extensor (KE) and the plantar flexor (PF) muscles' contractile function was measured by supramaximal electrical stimulations, potentiated low- and high-frequency doublets (PS10 and PS100) of the KE and the PF were measured by transcutaneous electrical nerve stimulation and bioimpedance was used to assess body composition in the runners (n = 11) before (Pre) and after (Post) the MUM and compared with the controls (n = 8). RESULTS: The maximal voluntary contraction of the KE and the PF significantly decreased by 20 % Post-MUM in the runners. Hydration of the non-fat mass (NF-Hyd) and extracellular water volume (Ve) were increased by 12 % Post-MUM (p < 0.001) in the runners. Calf circumference (+2 %, p < 0.05) was also increased. Significant relationships were found for percentage increases in Ve and NF-Hyd with percentage decrease in PS10 of the PF (r = -0.68 and r = -0.70, p < 0.05) and with percentage increase of calf circumference (r = 0.72 and r = 0.73, p < 0.05) in the runners. CONCLUSIONS: The present study suggests that increases in circumference and in hydric volume are associated to contractile impairment in the calf in ultra-marathon runners.

Architectural characterization of a delta-front reservoir analogue combining ground penetrating radar and electrical resistivity tomography: Roda Sandstone (Lower Eocene, Graus-Tremp basin, Spain)

Three-dimensional reconstruction of reservoir analogues can be improved combining data from different geophysical methods. Ground Penetrating Radar (GPR) and Electrical Resistivity Tomography (ERT) data are valuable tools, since they provide subsurface information from internal architecture and facies distribution of sedimentary rock bodies, enabling the upgrading of depositional models and heterogeneity reconstruction. The Lower Eocene Roda Sandstone is a well-known deltaic complex widely studied as a reservoir analogue that displays a series of sandstone wedges with a general NE to SW progradational trend. To provide a better understanding of internal heterogeneity of a 10m-thick progradational delta-front sandstone unit, 3D GPR data were acquired. In addition, common midpoints (CMP) to measure the sandstone subsoil velocity, test profiles with different frequency antennas (25, 50 and 100MHz) and topographic data for subsequent correction in the geophysical data were also obtained. Three ERT profiles were also acquired to further constrain GPR analysis. These geophysical results illustrate the geometry of reservoir analogue heterogeneities both depositional and diagenetic in nature, improving and complementing previous outcrop-derived data. GPR interpretation using radar stratigraphy principles and attributes analysis provided: 1)tridimensional geometry of major stratigraphic surfaces that define four units in the GPR Prism, 2) image the internal architecture of the units and their statistical study of azimuth and dips, useful for a quick determination of paleocurrent directions. These results were used to define the depositional architecture of the progradational sandbody that shows an arrangement in very-high-frequency sequences characterized by clockwise paleocurrent variations and decrease of the sedimentary flow, similar to those observed at a greater scale in the same system. This high-frequency sequential arrangement has been attributed to the autocyclic dynamics of a supply-dominated delta- front where fluvial and tidal currents are in competition. The resistivity models enhanced the viewing of reservoir quality associated with cement distribution caused by depositional and early diagenetic processes related to the development of transgressive and regressive systems tracts in igh-frequency sequences.