Inertial dissipation method applied to derive turbulent fluxed over the ocean during the Surface of the Ocean, Fluxes and Interactions with the Atmosphere Atlantic Stratocumulus Transition Experiment (SOFIA/ASTEX) and Structure des Echanges Mer-Atmosphere, Proprietes des Heterogeneites Oceaniques: Recherche Experimentale (SEMAPHORE) experiments with low to moderate wind speed

The transfer coefficients for momentum and heat have been determined for 10 m neutral wind speeds (U-10n) between 0 and 12 m/s using data from the Surface of the Ocean, Fluxes and Interactions with the Atmosphere (SOFIA) and Structure des Echanges Mer-Atmosphere, Proprietes des Heterogeneites Oceaniques: Recherche Experimentale (SEMAPHORE) experiments. The inertial dissipation method was applied to wind and pseudo virtual temperature spectra from a sonic anemometer, mounted on a platform (ship) which was moving through the turbulence held. Under unstable conditions the assumptions concerning the turbulent kinetic energy (TKE) budget appeared incorrect. Using a bulk estimate for the stability parameter, Z/L (where Z is the height and L is the Obukhov length), this resulted in anomalously low drag coefficients compared to neutral conditions. Determining Z/L iteratively, a low rate of convergence was achieved. It was concluded that the divergence of the turbulent transport of TKE was not negligible under unstable conditions. By minimizing the dependence of the calculated neutral drag coefficient on stability, this term was estimated at about -0.65Z/L. The resulting turbulent fluxes were then in close agreement with other studies at moderate wind speed. The drag and exchange coefficients for low wind speeds were found to be C-en x 10(3) = 2.79U(10n)(-1) + 0.66 (U-10n < 5.2 m/s), C-en x 10(3) = C-hn x 10(3) = 1.2 (U-10n greater than or equal to 5.2 m/s), and C-dn x 10(3) = 11.7U(10n)(-2) + 0.668 (U-10n < 5.5 m/s), which imply a rapid increase of the coefficient values as the wind decreased within the smooth flow regime. The frozen turbulence hypothesis and the assumptions of isotropy and an inertial subrange were found to remain valid at these low wind speeds for these shipboard measurements. Incorporation of a free convection parameterization had little effect.

Altimeter estimation of sea surface wind stress for light to moderate winds

Aircraft altimeter and in situ measurements are used to examine relationships between altimeter backscatter and the magnitude of near-surface wind and friction velocities. Comparison of altimeter radar cross section with wind speed is made through the modified Chelton-Wentz algorithm. Improved agreement is found after correcting 10-m winds for both surface current and atmospheric stability. An altimeter friction velocity algorithm is derived based on the wind speed model and an open-ocean drag coefficient. Close agreement between altimeter- and in situ-derived friction velocities is found. For this dataset, quality of the altimeter inversion to surface friction velocity is comparable to that for adjusted winds and clearly better than the inversion to true 10-m wind speed.

Arrastrar y Soltar

Drag & Drop es una aplicación web diseñada para la creación de problemas a partir de piezas, en la que al profesor se le plantea una nueva posibilidad de evaluar a sus alumnos. La aplicación web servirá como un entorno dedicado a la elaboración de preguntas y respuestas. Para responder a dichas preguntas, se proporcionan unos elementos llamados “piezas” al alumno que se encargará de utilizar para construir su respuesta. A su vez, el profesor al elaborar la pregunta establecerá la solución ideal del problema y el conjunto de “piezas” que los alumnos podrán utilizar para crear las suyas propias. El alumno al terminar la solución de un problema, la enviará al servidor. Este se encargará de evaluarla y comparar la solución del alumno con la solución ideal propuesta por el profesor.Finalmente el profesor será el encargado de examinar el ejercicio y ajustar la calificación, ya sea aceptando la que propone el sistema o indicando una propia.

Una herramienta web para la planificación de horarios y de asignaciones de aulas.

Este proyecto ha consistido en la realización de una aplicación web para cubrir una necesidad del centro universitario; la necesidad de gestionar los horarios y la asignación de aulas cada inicio de curso de una forma más automática de la que se usa en la actualidad. El objetivo principal ha sido que la aplicación fuera lo más intuitiva posible y que tenga una facilidad de uso que motivase su utilización. Para ello nos hemos decantado por una serie de características tanto visuales (distribución de la información, códigos de colores), como de uso (sistema de Drag&Drop). La aplicación tiene tres módulos principales: Un primer módulo para el manejo de los horarios, el cual nos permite la construcción de un horario para un grupo determinado evitando cualquier tipo de conflicto.El segundo módulo para la asignación de grupo a aulas, de forma que nos permite tener un control de los espacios del centro. El tercero y último, con una fuerte relación con el segundo, que en este caso se utiliza para asignar asignaturas optativas a aulas. Todo esto va acompañado por una variedad de páginas de información y de una vista administrativa para gestionar los datos necesarios para usar la aplicación. Una de las ventajas más importantes que tiene esta aplicación es la automatización a la hora de realizar todas las comprobaciones necesarias para hacer cualquier asignación. Debido a la envergadura del proyecto, optamos por realizar este proyecto conjuntamente entre tres personas para ser capaces de ofrecer un producto lo más completo posible sin salirnos de los límites de este trabajo de fin de grado.

Avaliação das atividades antioxidantes e citotóxicas de extratos ricos em polissacarídeos extraídos das hastes de mandacaru (Cereus Jamacaru de Candolle, Cactaceae)

The use of medicinal plants to cure and treat various diseases is a common practice in the world and in Brazil. In several regions of the Brazil´s Northeast, the cactus Cereus jamacaru, known as mandacaru, is used popularly as a treatment to many diseases, including those related to heart respiratory diseases, gastric ulcers, scurvy, and kidney diseases. However, there is a scarcity in the scientific literature that proves scientifically the popular application of this cactus. Like other plants, Cereus jamacaru synthesizes several potentially bioactive molecules, like as polysaccharides. In this work, three polysaccharides-rich aqueous extracts, MCA80, MPM and MCP60, were obtained from this plant and analyzed chemically, as well as their cytotoxic and antioxidant potential. The data showed that all extracts consist mainly of polysaccharides (89.42 to 95.76%), but also protein (> 2%) and phenolic (3 to 8.87%) contaminants were detected. All extracts are rich in galactose, glucose and mannose. In addition, glucuronic acid was found in MCA80 and MCP60. The extracts showed total antioxidant capacity ranged from 55.21 to 68.13 of ascorbic acid equivalents (AAE). Besides, they exhibited reducer power and cupric chelation in a dose-dependent manner. None of the extracts inhibited the MTT reduction in the presence of prostate tumor cells (PC-3). However, MCP60 was the most effective extract by preventing the reduction of MTT by about 80% in the presence of cells 786. Nuclear fragmentation tests showed that this extract induces cell death. The data indicated that mandacaru synthesizes bioactive polysaccharides with potential as antioxidant and antitumor agents. For future studies, it is intended to purify and characterize these polysaccharides and its antioxidant and antitumor mechanisms

A two-fluid model for tissue growth within a dynamic flow environment

We study the growth of a tissue construct in a perfusion bioreactor, focussing on its response to the mechanical environment. The bioreactor system is modelled as a two-dimensional channel containing a tissue construct through which a flow of culture medium is driven. We employ a multiphase formulation of the type presented by G. Lemon, J. King, H. Byrne, O. Jensen and K. Shakesheff in their study (Multiphase modelling of tissue growth using the theory of mixtures. J. Math. Biol. 52(2), 2006, 571–594) restricted to two interacting fluid phases, representing a cell population (and attendant extracellular matrix) and a culture medium, and employ the simplifying limit of large interphase viscous drag after S. Franks in her study (Mathematical Modelling of Tumour Growth and Stability. Ph.D. Thesis, University of Nottingham, UK, 2002) and S. Franks and J. King in their study Interactions between a uniformly proliferating tumour and its surrounding: Uniform material properties. Math. Med. Biol. 20, 2003, 47–89). The novel aspects of this study are: (i) the investigation of the effect of an imposed flow on the growth of the tissue construct, and (ii) the inclusion of a chanotransduction mechanism regulating the response of the cells to the local mechanical environment. Specifically, we consider the response of the cells to their local density and the culture medium pressure. As such, this study forms the first step towards a general multiphase formulation that incorporates the effect of mechanotransduction on the growth and morphology of a tissue construct. The model is analysed using analytic and numerical techniques, the results of which illustrate the potential use of the model to predict the dominant regulatory stimuli in a cell population.

Influência do uso de combustíveis alternativos na síntese por combustão via microondas para a produção de materiais cerâmicos com estrutura espinélio

The development and study of detectors sensitive to flammable combustible and toxic gases at low cost is a crucial technology challenge to enable marketable versions to the market in general. Solid state sensors are attractive for commercial purposes by the strength and lifetime, because it isn t consumed in the reaction with the gas. In parallel, the use of synthesis techniques more viable for the applicability on an industrial scale are more attractive to produce commercial products. In this context ceramics with spinel structure were obtained by microwave-assisted combustion for application to flammable fuel gas detectors. Additionally, alternatives organic-reducers were employed to study the influence of those in the synthesis process and the differences in performance and properties of the powders obtained. The organic- reducers were characterized by Thermogravimetry (TG) and Derivative Thermogravimetry (DTG). After synthesis, the samples were heat treated and characterized by Fourier Transform Infrared Spectroscopy (FTIR), X-ray Diffraction (XRD), analysis by specific area by BET Method and Scanning Electron Microscopy (SEM). Quantification of phases and structural parameters were carried through Rietveld method. The methodology was effective to obtain Ni-Mn mixed oxides. The fuels influenced in obtaining spinel phase and morphology of the samples, however samples calcined at 950 °C there is just the spinel phase in the material regardless of the organic-reducer. Therefore, differences in performance are expected in technological applications when sample equal in phase but with different morphologies are tested

Aerodynamic parametric analysis of an unconventional joined-wing aircraft configuration

In this paper, the experimental results of an unconventional joined-wing aircraft configuration are presented. The test model uses two different wings, forward and rear, both joined in tandem and forming diamond shapes both in plant and front views. The wings are joined in such a way that it is possible to change the rear wing dihedral angle values and the rear wing sweep angle values in 25 different positions that modify the relative distance and the relative height between the wings. To measure the system aerodynamic coefficients itis necessary to perform wind tunnel tests. The datapresented corresponds to the lift, drag and induced drag aerodynamic coefficients, as well as the aerodynamic efficiency and the parameter for minimum required power, from the calculated values of the lift and drag time series measured by a 6-axis force and torque sensor. The results show the influence on the aerodynamic coefficients of the rear wing sweep and dihedral angles parameters. As a main result, it can be concluded that, in general terms, the lift and induced drag aerodynamic coefficients values decrease as both the distance and height between the wings increase, on the other hand, the total drag aerodynamic coefficient decreases if the distance between the wings increases, but nevertheless shows a slight tendency to increase if the height of the rear wing increases, whereas the aerodynamic efficiency and the parameter for minimum required power increase if the distance between the wings increases

Packaging and Deployment of Large Planar Spacecraft Structures

This thesis presents a set of novel methods to biaxially package planar structures by folding and wrapping. The structure is divided into strips connected by folds that can slip during wrapping to accommodate material thickness. These packaging schemes are highly efficient, with theoretical packaging efficiencies approaching 100%. Packaging tests on meter-scale physical models have demonstrated packaging efficiencies of up to 83%. These methods avoid permanent deformation of the structure, allowing an initially flat structure to be deployed to a flat state.

Also presented are structural architectures and deployment schemes that are compatible with these packaging methods. These structural architectures use either in-plane pretension -- suitable for membrane structures -- or out-of-plane bending stiffness to resist loading. Physical models are constructed to realize these structural architectures. The deployment of these types of structures is shown to be controllable and repeatable by conducting experiments on lab-scale models.

These packaging methods, structural architectures, and deployment schemes are applicable to a variety of spacecraft structures such as solar power arrays, solar sails, antenna arrays, and drag sails; they have the potential to enable larger variants of these structures while reducing the packaging volume required. In this thesis, these methods are applied to the preliminary structural design of a space solar power satellite. This deployable spacecraft, measuring 60 m x 60 m, can be packaged into a cylinder measuring 1.5 m in height and 1 m in diameter. It can be deployed to a flat configuration, where it acts as a stiff lightweight support framework for multifunctional tiles that collect sunlight, generate electric power, and transmit it to a ground station on Earth.

Desenvolvimento de uma unidade pirolítica com reator de cilindro rotativo: obtenção de bio-óleo

The demand for alternative sources of energy drives the technological development so that many fuels and energy conversion processes before judged as inadequate or even non-viable, are now competing fuels and so-called traditional processes. Thus, biomass plays an important role and is considered one of the sources of renewable energy most important of our planet. Biomass accounts for 29.2% of all renewable energy sources. The share of biomass energy from Brazil in the OIE is 13.6%, well above the world average of participation. Various types of pyrolysis processes have been studied in recent years, highlighting the process of fast pyrolysis of biomass to obtain bio-oil. The continuous fast pyrolysis, the most investigated and improved are the fluidized bed and ablative, but is being studied and developed other types in order to obtain Bio-oil a better quality, higher productivity, lower energy consumption, increased stability and process reliability and lower production cost. The stability of the product bio-oil is fundamental to designing consumer devices such as burners, engines and turbines. This study was motivated to produce Bio-oil, through the conversion of plant biomass or the use of its industrial and agricultural waste, presenting an alternative proposal for thermochemical pyrolysis process, taking advantage of particle dynamics in the rotating bed that favors the right gas-solid contact and heat transfer and mass. The pyrolyser designed to operate in a continuous process, a feeder containing two stages, a divisive system of biomass integrated with a tab of coal fines and a system of condensing steam pyrolytic. The prototype has been tested with sawdust, using a complete experimental design on two levels to investigate the sensitivity of factors: the process temperature, gas flow drag and spin speed compared to the mass yield of bio-oil. The best result was obtained in the condition of 570 oC, 25 Hz and 200 cm3/min, temperature being the parameter of greatest significance. The mass balance of the elementary stages presented in the order of 20% and 37% liquid pyrolytic carbon. We determined the properties of liquid and solid products of pyrolysis as density, viscosity, pH, PCI, and the composition characterized by chemical analysis, revealing the composition and properties of a Bio-oil.

Simulação de fluxo de fluidos em meios porosos desordenados uma análise de efeito de escala na estimativa da permeabilidade e do coeficiente de arrasto

The present study provides a methodology that gives a predictive character the computer simulations based on detailed models of the geometry of a porous medium. We using the software FLUENT to investigate the flow of a viscous Newtonian fluid through a random fractal medium which simplifies a two-dimensional disordered porous medium representing a petroleum reservoir. This fractal model is formed by obstacles of various sizes, whose size distribution function follows a power law where exponent is defined as the fractal dimension of fractionation Dff of the model characterizing the process of fragmentation these obstacles. They are randomly disposed in a rectangular channel. The modeling process incorporates modern concepts, scaling laws, to analyze the influence of heterogeneity found in the fields of the porosity and of the permeability in such a way as to characterize the medium in terms of their fractal properties. This procedure allows numerically analyze the measurements of permeability k and the drag coefficient Cd proposed relationships, like power law, for these properties on various modeling schemes. The purpose of this research is to study the variability provided by these heterogeneities where the velocity field and other details of viscous fluid dynamics are obtained by solving numerically the continuity and Navier-Stokes equations at pore level and observe how the fractal dimension of fractionation of the model can affect their hydrodynamic properties. This study were considered two classes of models, models with constant porosity, MPC, and models with varying porosity, MPV. The results have allowed us to find numerical relationship between the permeability, drag coefficient and the fractal dimension of fractionation of the medium. Based on these numerical results we have proposed scaling relations and algebraic expressions involving the relevant parameters of the phenomenon. In this study analytical equations were determined for Dff depending on the geometrical parameters of the models. We also found a relation between the permeability and the drag coefficient which is inversely proportional to one another. As for the difference in behavior it is most striking in the classes of models MPV. That is, the fact that the porosity vary in these models is an additional factor that plays a significant role in flow analysis. Finally, the results proved satisfactory and consistent, which demonstrates the effectiveness of the referred methodology for all applications analyzed in this study.

An Investigation of Vertical Turbulent Transport Processes in Coastal Regions Using Tower Observations

High-resolution tower observations of turbulent transport processes in the coastal atmospheric surface layer show that the exchange coefficients for momentum, enthalpy, and moisture behave differently for different environmental and atmospheric conditions. The drag coefficient is closely tied to wind speed and turbulent intensity. The exchange coefficient for enthalpy shows a dependence on stability. Analysis of the turbulent kinetic energy budget yields a new parameterization framework that well explains the observed variation of the drag coefficient, particularly at low wind speeds.

Carrier momentum relaxation in highly doped polar semiconductors and semiconductor heterostructures

Highly doped polar semiconductors are essential components of today’s semiconductor industry. Most strikingly, transistors in modern electronic devices are polar semiconductor heterostructures. It is important to thoroughly understand carrier transport in such structures. In doped polar semiconductors, collective excitations of the carriers (plasmons) and the atoms (polar phonons) couple. These coupled collective excitations affect the electrical conductivity, here quantified through the carrier mobility. In scattering events, the carriers and the coupled collective modes transfer momentum between each other. Carrier momentum transferred to polar phonons can be lost to other phonons through anharmonic decay, resulting in a finite carrier mobility. The plasmons do not have a decay mechanism which transfers carrier momentum irretrievably. Hence, carrier-plasmon scattering results in infinite carrier mobility. Momentum relaxation due to either carrier–plasmon scattering or carrier–polar-phonon scattering alone are well understood. However, only this thesis manages to treat momentum relaxation due to both scattering mechanisms on an equal footing, enabling us to properly calculate the mobility limited by carrier–coupled plasmon–polar phonon scattering. We achieved this by solving the coupled Boltzmann equations for the carriers and the collective excitations, focusing on the “drag” term and on the anharmonic decay process of the collective modes. Our approach uses dielectric functions to describe both the carrier-collective mode scattering and the decay of the collective modes. We applied our method to bulk polar semiconductors and heterostructures where various polar dielectrics surround a semiconducting monolayer of MoS2, where taking plasmons into account can increase the mobility by up to a factor 15 for certain parameters. This screening effect is up to 85% higher than if calculated with previous methods. To conclude, our approach provides insight into the momentum relaxation mechanism for carrier–coupled collective mode scattering, and better tools for calculating the screened polar phonon and interface polar phonon limited mobility.

Modelling the relationship between biomechanics and performance of young sprinting swimmers

The aim of this study was to compute a swimming performance confirmatory model based on biomechanical parameters. The sample included 100 young swimmers (overall: 12.3 ± 0.74 years; 49 boys: 12.5 ± 0.76 years; 51 girls: 12.2 ± 0.71 years; both genders in Tanner stages 1–2 by self-report) participating on a regular basis in regional and national-level events. The 100 m freestyle event was chosen as the performance indicator. Anthropometric (arm span), strength (throwing velocity), power output (power to overcome drag), kinematic (swimming velocity) and efficiency (propelling efficiency) parameters were measured and included in the model. The path-flow analysis procedure was used to design and compute the model. The anthropometric parameter (arm span) was excluded in the final model, increasing its goodness-of-fit. The final model included the throw velocity, power output, swimming velocity and propelling efficiency. All links were significant between the parameters included, but the throw velocity–power output. The final model was explained by 69% presenting a reasonable adjustment (model’s goodness-of-fit; x2/df = 3.89). This model shows that strength and power output parameters do play a mediator and meaningful role in the young swimmers’ performance.

A reactividade do clinquer

A indústria cimenteira é uma indústria com grandes gastos energéticos, sendo por Isso de extrema importância, do ponto de vista económico, desenvolver estratégias e procedimentos que conduzam à sua minimização. O intuito da realização do presente trabalho foi estudar a reactividade do clínquer da Cimpor­ Centro de Produção de Loulé, ao introduzir alterações ao processo de fabrico de cimento. O estudo engloba três objectivos: C. Melhorar a qualidade do clínquer; C. Reduzir o consumo térmico do forno; C. Reduzir o consumo energético dos moinhos de cimento. Na paragem de Maio de 2008 foi instalado um novo redutor para o motor do forno que permitiu alterar a velocidade máxima de 2 para 3,5 rpm, o que consequentemente diminuiu a taxa de enchimento de ≈20% para ≈14%. Os resultados mostraram que com a alteração ao processo atingiram-se dois dos três objectivos pretendidos. Isto é, obteve-se um clínquer de melhor qualidade e houve uma diminuição do consumo térmico do forno. Contudo, não se conseguiram tirar conclusões acerca do consumo energético dos moinhos de cimento, sendo para tal, necessário prolongar o tempo do estudo. ABSTRACT: The cement industry is an industry with high energy costs and is therefore of extreme importance, in economic terms, to develop strategies and procedures that lead to its minimization. The purpose of this work was to study the reactivity of the clinker produced at Loulé Cimpor Production Center by introducing changes in the manufacture process of cement. The study comprised three main objectives: C. Improving the quality of the clinker; C. Reducing the heat consumption of the furnace; C. Reducing energy consumption of the cement mills. During the stop of May 2008 a new reducer was installed in the furnace motor which allowed changing the maximum speed of 2 to 3.5 rpm, which consequently decreased the rate of filling from ≈20% to ≈14%. The results showed that with the process modification, two of the three objectives were reached up. That is, a better quality of clinker was obtained and there was a decrease in the heat consumption of the furnace. However, during the period of this study it was not possible to draw a final conclusion about the energy consumption of the cement mills, and therefore, it is necessary to study the process for a longer period of time.