Direct shear testing on unsaturated silty soils to investigate the effects of drying and wetting on shear strength parameters at low suction

A modified conventional direct shear device was used to measure unsaturated shear strength of two silty soils at low suction values (0 ~ 50 kPa) that were achieved by following drying and wetting paths of soil water characteristic curves (SWCCs). The results revealed that the internal friction angle of the soils was not significantly affected by either the suction or the drying wetting SWCCs. The apparent cohesion of soil increased with a decreasing rate as suction increased. Shear stress-shear displacement curves obtained from soil specimens subjected to the same net normal stress and different suction values showed a higher initial stiffness and a greater peak stress as suction increased. A soil in wetting exhibited slightly higher peak shear stress and more contractive volume change behavior than that of soil in drying at the same net normal stress and suction.

Cavitation erosion characteristics of poly(methyl methacrylate) in a rotating disk device

Experimental results pertaining to the initiation, dynamics and mechanism of cavitation erosion on poly(methyl methacrylate) specimens tested in a rotating disk device are described in detail. Erosion normally starts at the location nearest to the center of rotation (CR). As the exposure time to cavitation increases, additional erosion areas or sites appear away from the CR and secondary erosion (induced by eroded pits) spreads upstream and merges with the main pit. The microcracks increase in density towards the end of the incubation period and transform into macrocracks in most cases. A study of light optical photographs and scanning electron micrographs of the eroded area shows that material particles are removed from the network of cracks because of crack joining and pits indicate particle debris. Optical degradation (loss of transmittance) is observed to be greater on the back of the specimen than on the front.

On the wear of aluminium-corundum composites

The effect of corundum particle content on the wear of aluminium was studied. Composites of different corundum contents were tested for their wear characteristics. Hardness and density measurements were made on specimens before and after test. Specimens were examined by scanning electron microscopy in the as-compacted, sintered and worn states. The wear decreased as the oxide content increased, showing an optimum value at a composition range of 25 wt.%–35 wt.% of corundum. The mechanism of reinforcement and its effect on the operative wear mode are discussed.

On the Cubicity of Interval Graphs

A k-cube (or ``a unit cube in k dimensions'') is defined as the Cartesian product R-1 x . . . x R-k where R-i (for 1 <= i <= k) is an interval of the form [a(i), a(i) + 1] on the real line. The k-cube representation of a graph G is a mapping of the vertices of G to k-cubes such that the k-cubes corresponding to two vertices in G have a non-empty intersection if and only if the vertices are adjacent. The cubicity of a graph G, denoted as cub(G), is defined as the minimum dimension k such that G has a k-cube representation. An interval graph is a graph that can be represented as the intersection of intervals on the real line - i. e., the vertices of an interval graph can be mapped to intervals on the real line such that two vertices are adjacent if and only if their corresponding intervals overlap. We show that for any interval graph G with maximum degree Delta, cub(G) <= inverted right perpendicular log(2) Delta inverted left perpendicular + 4. This upper bound is shown to be tight up to an additive constant of 4 by demonstrating interval graphs for which cubicity is equal to inverted right perpendicular log(2) Delta inverted left perpendicular.

Phylogenetic considerations for predicting the host range of Ustilago sporoboli-indici, a potential biological control agent for Sporobolus species in Australia

The ribosomal DNA internal transcribed spacer region was amplified and sequenced from a selection of specimens of the Sporobolus smut Ustilago sporoboli-indici. Phylogenetic comparison with other Ustilago and Sporisorium species revealed strong support for an evolutionary radiation of Ustilago species infecting the Chloridoideae and Pooideae, of which U. sporoboli-indici forms a major lineage. Comparisons are made with other groups of plant pathogenic fungi, and it is concluded that phylogenetic analyses of potential biocontrol agents are useful for identifying pathogens that are derived from evolutionary lineages that parasitize a wide range of unrelated plants. Such pathogens are less desirable as biocontrol agents as they may have a greater likelihood of infecting plants outside their normal host ranges.

Borate protection of softwood from Coptotermes acinaciformis (Isoptera: Rhinotermitidae) damage: Variation in protection thresholds explained

Laboratory and field data reported in the literature are confusing with regard to “adequate” protection thresholds for borate timber preservatives. The confusion is compounded by differences in termite species, timber species and test methodology. Laboratory data indicate a borate retention of 0.5% mass/mass (m/m) boric acid equivalent (BAE) would cause >90% termite mortality and restrict mass loss in test specimens to ≤5%. Field data generally suggest that borate retentions appreciably >0.5% m/m BAE are required. We report two field experiments with varying amounts of untreated feeder material in which Coptotermes acinaciformis (Froggatt) (Isoptera: Rhinotermitidae) responses to borate-treated radiata (Monterey) pine, Pinus radiata D. Don, were measured. The apparently conflicting results between laboratory and field data are explained by the presence or absence of untreated feeder material in the test environment. In the absence of untreated feeder material, wood containing 0.5% BAE provided adequate protection from Coptotermes sp., whereas in the presence of untreated feeder material, increased retentions were required. Furthermore, the retentions required increased with increased amounts of susceptible material present. Some termites, Nasutitermes sp. and Mastotermes darwiniensis Froggatt, for example, are borate-tolerant and borate timber preservatives are not a viable management option with these species. The lack of uniform standards for termite test methodology and assessment criteria for efficacy across the world is recognized as a difficulty with research into the performance of timber preservatives with termites. The many variables in laboratory and field assays make “prescriptive” standards difficult to recommend. The use of “performance” standards to define efficacy criteria (“adequate” protection) is discussed.

Field assessment of the resistance of timber products to termite (Isoptera) damage: Results can change with the amount of bait wood

Whether or not termites initiate damage to timber via the end grain may determine the need for spot-treating the exposed untreated cut ends of envelope-treated softwood framing material. Australian Coptotermes acinaciformis (Froggatt) were field-tested for their ability to initiate feeding via the end grain of timber (35 × 90 mm) treated with a repellent Tanalith® T envelope. Specimens of commercial radiata pine Pinus radiata D.Don framing timber (untreated) and slash pine Pinus elliottii Englem. (untreated and envelope-treated) were partially clad in fine stainless steel mesh. Clad and unclad specimens were exposed to C. acinaciformis near Townsville, North Queensland, Australia, for four months. Results showed that this species of termite can indeed damage timber via the end grain, including exposed untreated cut ends of envelope-treated material as demonstrated earlier for different populations of C. acinaciformis. Differences between the test conditions in field trials carried out at different times (where C. acinaciformis either did or did not damage timber via the end grain) are discussed. Clearly, outcomes from field studies with preservative-treated materials are dependent upon experimental conditions. Notably, the amount of bait wood (highly termite-susceptible timber substrate) offered in a given method can strongly influence the termite response. Further investigation is required to standardise this aspect of conditions in protocols for the assessment of wood preservatives.

New records of the River Shark Glyphis (Carcharhinidae) reported from Cape York Peninsula, northern Australia

The distribution of the river shark Glyphis in northern Australia is extended with new records of occurrence in the Gulf of Carpentaria and a reassessment of historical survey data from Cape York Peninsula. Nine new specimens of Glyphis sp. A were collected in 2005 from the Weipa region on the Queensland coast of the Gulf of Carpentaria. A re-examination of archival records from 1978-86 marine and estuarine fish surveys in the Gulf of Carpentaria and along the northern Queensland East Coast allowed a further nineteen Glyphis specimens to be identified. Combined this gives twenty-eight new records of Glyphis specimens from the coasts of Cape York Peninsula, Queensland. Common habitat characteristics for all captures were turbid, shallow, fast running tidal water in the upper reaches of coastal rivers. The substrate was generally muddy and the rivers lined with mangrove. In all surveys the representation of Glyphis was low, being less than 1% of the total shark captures historically and 0.002 sharks 50 m net hour-1 in Weipa 2005. The size range captured was 1000-1800 mm total length historically and 705-1200 mm total length from Weipa 2005, with none recorded as sexually mature. Diagnostic characteristics of the Weipa specimens, identified as Glyphis sp. A, were: lower jaw teeth protruding and "spear-like"; second dorsal fin greater than half the height of the first dorsal fin; the snout relatively short and fleshy in the lateral view; pectoral fin ventral surface black in colouration; the precaudal vertebral count between 118 and 123; and the total vertebral count between 204 and 209.

Fishery biology and management of Protonibea diacanthus (Sciaenidae) aggregations in far Northern Cape York Peninsula waters

The sciaenid Protonibea diacanthus is a large, long-lived predatory fish of inshore northern Australian waters, which forms annual aggregations that are fished extensively by traditional (subsistence) and recreational fishers. There are now widespread concerns that the resource is being overexploited. Indigenous fishers of the Cape York Northern Peninsula Area (NPA) relate that large adult fish (up to 1500 mm total length (TL)) made up the bulk of the catch from the sciaenid aggregations until about 1994. In contrast, sexually mature P. diacanthus comprised only a small component (12 fish out of 270=4.4%) examined in a 1999–2000 sampling programme that was biased towards the largest individuals available. At 790 mm TL, the minimum size at first maturity for female P. diacanthus in this study is much smaller than the 920 mm TL reported previously in Queensland waters. Developing ovaries were observed in specimens sampled from sciaenid aggregations which formed in NPA waters between May and September 2000. However, no fish with ripe or spent gonads were found in the study, so the current timing and location of the spawning season for P. diacanthus in the region remain unknown. Food items observed in the analysis of the diet of P. diacanthus from the NPA included a variety of teleosts and invertebrates. The range of animal taxa represented in the prey items support the description of an ‘opportunistic predator’ attributed to the species. In our sampling, the stomach contents of fish caught during the time of the aggregation events did not differ from those observed at other times of the year. A total of 114 P. diacanthus were tagged and released at aggregation sites during the study period, and 3 fish (2.6%) were subsequently recaptured. The low rate of tag returns from the wild stock tagging programme, both in this study (2.6%) and from recreational fisher tag/release programmes for the sciaenid elsewhere in Queensland (6.5%), were not explained by tag loss nor mortality, given the high retention rate of tags and the zero mortality seen in tank trials. In response to the biological findings from this study, indigenous community councils of the NPA imposed a 2-year fishing moratorium for P. diacanthus. Surveys at aggregation sites in 2002 and 2003 established that much larger fish (mean size 103.5 cm TL) were again present on the grounds, albeit in very low numbers. These recent preliminary results highlight the critical need for continued monitoring and management of the P. diacanthus fishery in the NPA, if prospects for resource recovery are to be realised. The NPA initiative has provided a rare opportunity to negotiate a co-management strategy, based on scientific data and traditional knowledge, for the recovery of a cultural and economically significant fished resource.

An annotated checklist of smut fungi (Ustilaginomycetes) from Thailand

An annotated checklist of the smut fungi (Ustilaginomycetes) from Thailand has been compiled after an examination of the scientific literature, previously deposited herbarium specimens and specimens collected by the authors during a survey in December 2005. Fifty-two species of smut fungi are listed, including 11 species which were newly discovered during our survey. Most of these smut fungi are reported for the first time from Thailand. Several species are very rare, being known only from the type material or a limited number of collections.

Constraint effects on multiple void interaction in pressure sensitive plastic solids

In this work, effects of pressure sensitive yielding and plastic dilatancy on void growth and void interaction mechanisms in fracture specimens displaying high and low constraint levels are investigated. To this end, large deformation finite element simulations are carried out with discrete voids ahead of the notch. It is observed that multiple void interaction mechanism which is favored by high initial porosity is further accelerated by pressure sensitive yielding, but is retarded by loss of constraint. The resistance curves predicted based on a simple void coalescence criterion show enhancement in fracture resistance when constraint level is low and when pressure sensitivity is suppressed.

Epitypification and phylogeny of Colletotrichum acutatum J.H. Simmonds

Simmonds introduced Colletotrichum acutatum in 1965, validated in 1968, with a broad concept, as demonstrated by the selection of several type specimens from a range of hosts. This has created some confusion in the species concept and identification of C. acutatum. There are no viable ex-type cultures of C. acutatum and furthermore there are no existing cultures of C. acutatum on Carica papaya from the type locality in south-east Queensland. The application of molecular phylogenetic studies to isolates of C. acutatum is only meaningful if the taxonomy is stable and species are properly named. In order to clarify the species concept of C. acutatum, an isolate of Colletotrichum acutatum from Carica papaya from Yandina in Southeast Queensland (Australia) is designated as an epitype. A detailed morphological description is provided. Phylogenies based on a combined ITS and beta-tubulin gene analysis indicate that C. acutatum bears close phylogenetic affinities to C. gloeosporioides and C. capsici. Results also indicate that C. acutatum is monophyletic and there is a close relationship between the epitype and other Australian C. acutatum isolates from Carica papaya. Molecular data, however did not provide further evidence to properly elucidate the taxonomie affinities of C. acutatum especially the holotype and epitype. Our studies indicate that given the complexity of the genus Colletotrichum, there is a need to check previously described type specimens and redesign neotypes where necessary in order to clarify taxonomie uncertainties.

Concordant molecular and phenotypic data delineate new taxonomy and conservation priorities for the endangered mountain yellow-legged frog

The mountain yellow-legged frog Rana muscosa sensu lato, once abundant in the Sierra Nevada of California and Nevada, and the disjunct Transverse Ranges of southern California, has declined precipitously throughout its range, even though most of its habitat is protected. The species is now extinct in Nevada and reduced to tiny remnants in southern California, where as a distinct population segment, it is classified as Endangered. Introduced predators (trout), air pollution and an infectious disease (chytridiomycosis) threaten remaining populations. A Bayesian analysis of 1901 base pairs of mitochondrial DNA confirms the presence of two deeply divergent clades that come into near contact in the Sierra Nevada. Morphological studies of museum specimens and analysis of acoustic data show that the two major mtDNA clades are readily differentiated phenotypically. Accordingly, we recognize two species, Rana sierrae, in the northern and central Sierra Nevada, and R. muscosa, in the southern Sierra Nevada and southern California. Existing data indicate no range overlap. These results have important implications for the conservation of these two species as they illuminate a profound mismatch between the current delineation of the distinct population segments (southern California vs. Sierra Nevada) and actual species boundaries. For example, our study finds that remnant populations of R. muscosa exist in both the southern Sierra Nevada and the mountains of southern California, which may broaden options for management. In addition, despite the fact that only the southern California populations are listed as Endangered, surveys conducted since 1995 at 225 historic (1899-1994) localities from museum collections show that 93.3% (n=146) of R. sierrae populations and 95.2% (n=79) of R. muscosa populations are extinct. Evidence presented here underscores the need for revision of protected population status to include both species throughout their ranges.

The complexities of knowing what it is you are trapping

The effectiveness of any trapping system is highly dependent on the ability to accurately identify the specimens collected. For many fruit fly species, accurate identification (= diagnostics) using morphological or molecular techniques is relatively straightforward and poses few technical challenges. However, nearly all genera of pest tephritids also contain groups of species where single, stand-alone tools are not sufficient for accurate identification: such groups include the Bactrocera dorsalis complex, the Anastrepha fraterculus complex and the Ceratitis FAR complex. Misidentification of high-impact species from such groups can have dramatic consequences and negate the benefits of an otherwise effective trapping program. To help prevent such problems, this chapter defines what is meant by a species complex and describes in detail how the correct identification of species within a complex requires the use of an integrative taxonomic approach. Integrative taxonomy uses multiple, independent lines of evidence to delimit species boundaries, and the underpinnings of this approach from both the theoretical speciation literature and the systematics/taxonomy literature are described. The strength of the integrative approach lies in the explicit testing of hypotheses and the use of multiple, independent species delimitation tools. A case is made for a core set of species delimitation tools (pre- and post-zygotic compatibility tests, multi-locus phylogenetic analysis, chemoecological studies, and morphometric and geometric morphometric analyses) to be adopted as standards by tephritologists aiming to resolve economically important species complexes. In discussing the integrative approach, emphasis is placed on the subtle but important differences between integrative and iterative taxonomy. The chapter finishes with a case study that illustrates how iterative taxonomy applied to the B. dorsalis species complex led to incorrect taxonomic conclusions, which has had major implications for quarantine, trade, and horticultural pest management. In contrast, an integrative approach to the problem has resolved species limits in this taxonomically difficult group, meaning that robust diagnostics are now available.

Re-use of fluoride contaminated bone char sludge in concrete

Managing sludge generated by treating groundwater contaminated with geogenic contaminants (fluoride, arsenic, and iron) is a major issue in developing nations. Their re-use in civil engineering applications is a possible pathway for reducing the impact on the geo-environment. This paper examines the re-use of one such sludge material, namely, fluoride contaminated bone char sludge, as partial replacement for fine aggregate (river-sand) in the manufacture of dense concrete specimens. Bone char sludge is being produced by defluoridation of contaminated groundwater in Nalagonda District, Andhra Pradesh, India. The impact of admixing 1.5-9% sludge contents on the compression strength and fluoride leaching potential of the sludge admixed concrete (SAC) specimens are examined. The compression strengths of the SAC specimensa re examined with respect to strength criteria for manufacture of dense, load-bearing concrete blocks. The fluoride release potential of the SAC specimens is examined with respect to standards specific to disposal of treated leachate into inland surface water.