Otimização ecológica dos ciclos ar-padrão Otto e Diesel

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Efeito do acréscimo de nano-hidroxiapatita nas propriedades físico-químicas, mecânicas e antibiofilnme do cimento portland com óxido de zircônio

Pós-graduação em Odontologia - FOAR

Obtenção e caracterização de suporte de regeneração óssea de dióxido de titânio

Due to complications caused by metallic implants in the replacement of bone tissue, the biological application of ceramics raised and became a viable alternative. The titania has the ability to promote bone tissue regeneration based on its structure, mechanical and biologically properties compatibility. The present work aims at obtaining and characterization of Titania (TiO2) porous ceramics produced by the polymeric sponge method (replica method). Polyurethane sponge with 10 ppi and 15 ppi (pores per linear inch) were used. The process differentiation is the air blower used to remove excess slurry. The ceramics sponges were dried in an oven, then pre-sintered at 1000 o C and sintered at 1450 o C. The effect of direct sintering at 1450 o C was also assessed. The percentage of solids used to prepare the slurry was 40 to 45% by weight. To increase the surface porosity of the sponge, 20% of starch was added. There was difficulty on controlling the thickness of the slurry layers on the sponge which resulted in the variation of samples mechanical resistance. Despite this, the results obtained are quite promising for the proposed use, indicating that it is possible to obtain titania sponges with an apparent porosity of around 60%, a bulk density ranging from 40 to 47% and a compressive strength resistance – that with better control of layers depositions – can vary from 1 to 4 MPa

Acupuntura no tratamento de discopatias intervertebrais em cães

The intervertebral disc disease is considered a major neurological disorder involving the spinal cord, being a disease commonly seen in dogs in clinical practice of small animals. The pathophysiology of most discopathies have not been fully elucidated, but it is known that the symptoms observed will depend on the severity of spinal cord compression and location of spinal injury, ranging from localized pain to complete paralysis. Through a detailed clinical examination and laboratory tests, we choose the most appropriate treatment for each patient, which can be conservative, through the use of anti-inflammatories, analgesics and acupuncture or surgical, through decompression techniques. Acupuncture, therapeutic method of ancient Chinese medicine, uses the stimulation of specific points on the body in order to balance the body's physiological. The action mechanism of acupuncture in discopathies has not been fully elucidated, but its analgesic effects, anti-inflammatory and restoration of sensory and motor function are known, showing results as good as surgical therapy

Precificação do biogás produzido por autoprodutores, considerando seu transporte por meio de gasodutos existentes

The expansion of the energy matrix is a matter of great importance since the recent problems facing the country in this sector, such as rationing mobilized in 2001. Moreover, there is also concern with global sustainable development. Brazil is producing about 64 million cubic meters of biogas per day, but only a small percentage of this total is harnessed as an energy resource. Compounders are considered potential, for example, landfill energy (LE) and sewage treatment plants (STP), which can be adapted to produce biogas and market them. The work focuses its studies on biogas produced by these small and medium compounders. Are proposed and studied the following alternatives for the utilization of biogas energy: generation and sale of electricity through the installation of a small power station within the landfill, and purification and marketing of gas, whose price will be a consideration on the price of natural gas, taking into account the percentage of methane present in the biogas. Trade ensures that gas plus a destination ecologically appropriate to it, taking advantage of its energy

Modelagem e simulação numérica de um sistema de refrigeração por absorção utilizando o par H2O-LiBr

The term refrigeration solar refers to any air conditioning system that uses solar energy as a primary energy source. The use of solar radiation for cooling purposes is divided according to their technological possibilities which are distinguished from one another as the way that energy is involved in the cycle, work or heat. The first case is related to vapor compression cycles, in which the work input is provided by the photovoltaic conversion of solar energy into electrical energy. In the second case, an absorption refrigeration cycle is used and the thermal energy collected from the solar radiation is provided at the generator of this cycle.. In this work a system with an absorption cycle using the pair BrLi-water, using solar energy as input is modeled. It is considered a simple refrigeration cycle whose the equations of mass and energy conservation in each component are developed in order to obtain an algebraic equation set and a simulation routine using the EES software. Although the simulation operates under certain specified thermal load it is possible to estimate the necessary areas of heat exchangers and solar collectors

Quantificação da desintegração de comprimidos por fluxo ótico em seqüências de imagens de biosusceptometria AC

AC Biosusceptometry (ACB) is a low-cost biomagnetic tool that has been successfully applied on pharmaceutical research to evaluate performance of solid dosage forms. The aim of this work was to evaluate the Horn & Shunck method to access tablet disintegration. To evaluate the HS results was record on video a test with a objet moving in a rail with a constant velocity. The desintegration was recorded on video and ACB, which used have seven pairs of detection coils and a pair of excitation coils to mensure the magnetic ux variation. The signals were ampli ed and digitalized to create images, which were restored by Wiener lter, while the video images are converted to gray scale, both are normalized and binarized and had the optical ow estimation calculated by Horn & Schunck (HS) algorithm. All signals and images are processed and developed algorithm on Matlab. During the tests the ve tablets (500mg ferrite, 375mg excipients, compression 10 to 50 kN) were on a becker between of the ACB system and of the video system, and only touching the surface of the water. With all OF maps calculated was realized the sum of the resultants of each, to get a disintegration process resultant for each compression. Whit that was possible observed the disintegration behaves. For the compression force study the HS components of each sequence was sum, take mean and normalized for sequence's max modulo, therefore can be observed a high growing on less compression tablets. We can conclude the HS algorithm is viable to tablets disintegration data collection and whit that was possible to create a tablets disintegration analyzes protocol, which would be useful on desintegration kinetics study

Análise estrutural de Tie-Rod pelo método dos elementos finitos e através de cálculos analíticos

Currently one of the great concerns of the aeronautical industry is in relation to the security and integrity of the aircraft and its equipments / components when under critical flight maneuvers such as during landing / takeoff and emergency maneuvers. The engineers, technicians and scientists are constantly developing new techniques and theories to reduce the design time and testing, ir order to minimize costs. More and more the Finite Element Method is used in the structural analysis of a project as well as theories based on experimental results. This work aimed to estimate the critical load to failure for tensile, compression and buckling of the Tie-Rod, a fixture aircraft widely used on commercial aircrafts. The analysis was performed by finite element method with the assistance of software and by analytical calculations. The results showed that the Finite Element Method provides relative accuracy and convenience in the calculations, indicating critical load values slightly lower than those found analytically for tension and compression. For buckling, the Finite Element Method indicates a critical load very similar to that found analytically following empirical theories, while Euler's theory results in a slightly higher value. The highest risk is to fail by buckling, but the geometric irregularity of Tie-Rod pieces makes difficult the calculations, therefore a practical test must be done before validation of the results

Análise granulométrica do compósito cimentício produzido com adição de resíduos de madeira e escória

Since the early twenty-first century, the construction sector has been the second largest on the rise in the Brazilian industrial sector, with a growth of 1.4% in 2012, and is likely to remain at this level for a long time. However, unlike decades ago, the industry has been seeking in its manufacturing process, sustainable materials, encompassing in their works the concept of sustainability. Thus, the timber sector seeks to satisfy a market increasingly demanding, innovating techniques and utilization being less aggressive to the environment. The purpose of this study was to produce and evaluate the mechanical strength of the composite cement with the addition of wood residues and slag low oven. Therefore, it was made 42 specimen cement-slag-wood, carried out in two steps. Since at the first, it was varied only the slag particle size, and at the second, through the best result of the previous step, it was varied the wood particles granulometry. The mechanical performance of the composite was evaluated by the results obtained in the compression test and the physical test for determining the density of the material. In the first step of the process can be concluded that the best result was achieved with the use of slag particles retained on the 60 mesh sieve. In the second phase of the study concluded that the best results were achieved with wood particles with the large particles, i.e. particles retained on the 10 mesh sieve. Both in the first and in the second step it can be seen that there has been the influence of the particle size of the waste materials. With the obtained results, could be evaluated that the use of waste for the production of cement-slag-wood composite showed lower performance when compared to the results obtained in studies without the use of waste. However, some applications are feasible to be performed with the use of composite wood-cement-slag

Projeto de um dispositivo para prensar bobinas polares de pólos salientes para hidrogeradores

The increasing demand for productivity and quality in companies has converged to a common point: reducing costs. In this context the present work aims at the development of a mechanical press which is designed for pressing polar hydrogenerators coils with salient pole in field facilitating the assembly of the poles in the plant, as well as reforms especially in hydrogenerators, reducing significantly the transport costs. With security in mind as well as reduced costs, a study was made of the materials to be used as it was applied a methodology for calculating the correct choice of safety factor to be used in the device. Through mechanical calculations were dimensioned critical items of the device as the diameter of the rods as well as the minimum thickness of the base of the device must have so that it does not break threaded shear in the region by applying the total load of traction on the risers implementation of the pressing. All compression loading device will be through the application of torque on the nuts of bolts in this way was defined by calculations the required torque for each nut so that you can reach the pressure specified in the design specifies. The modeling of the device was made using the INVENTOR™ program in conjunction with the program ANSYS ™. These programs have created designs in three dimensions, assembly and simulation of stress analysis in components of the device

Subluxação atlantoaxial canina

The atlantoaxial subluxation or luxation is an instability of this articulation that produces excessive flexion of this joint causing the cranial aspect of the axis to rotate dorsally into the vertebral channel with subsequent spinal cord compression. This disorder is most commonly found in young small breed dogs. The diagnosis of this disease is done by survey radiographs, where there is a larger distance between the atlas dorsal arch and the axis spinal process characterize the atlantoaxial subluxation. Surgical stabilization is the treatment of choice and multiple implants show the best results to stabilize the atlantoaxial joint. The main complications are sudden death or implant failure. The sudden death happens because of cardiorespiratory arrest and it is most likely caused by brainstem iatrogenic trauma. However, a larger study comparing different surgical stabilization techniques should be performed to evaluate relative success rates in dogs that have the same initial neurologic status

Análise das propriedades da madeira de estrutura de telhado após a ocorrência de um incêndio

The present study evaluated the mechanical properties of pieces of wood coming from the roof structure of a residence subject fire in the rural area of Itapeva/SP. The structure was built 25 years ago using wooden beams of the species Guarucaia (Peltophorum vogelianum), where the specimens were removed. The research methodology included qualitative evaluation of the samples, estimating the layer pyrolysis and carbonization of the wood, measuring of density and mechanical tests of compression parallel to grain, tension parallel to grain and shear. The mechanical properties of wood were analytically correlated with the layers carbonization and pyrolysis that are influenced by the temperature and time of fire; these values were estimated at 1000 °C and two hours for the case in question. The results indicate that the strength properties of degraded wood are different from a healthy wood. The level of thermodegradation, in general, can be measured by density, result in weight loss due to decomposition of the wooden components.

Metodologia de determinação das curvas de probabilidade de falha S-N-P para uma liga de aluminio submetida a diferentes tratamentos termicos de solubilização e precipitação

The approach of the subject matter in this work relies on the fact that the reliability of methods for performance analysis of materials proves critical for the result. This work focused on the development and presentation of the methodology for lifting probability curves for fatigue test (SN) according to standard E739, this focus is justified by the fact that the results in fatigue test show considerable dispersion making it difficult to reading and interpretation of data, this dispersion arises because the phenomenon of rupture is strongly influenced by internal characteristics of the material, we can then have much data ranging from test to test. Thus we set out originally for a brief study of aluminum alloys in question, as well as the treatments to which they were subjected. We also studied the behavior of materials when subjected to cyclic loading, which configures process of fatigue failure, and even fatigue test method in question. This statistical analysis is based on the ASTM E739 standard, so its contents was studied in detail so that we could present in detail the methodology and raise SN curves for different aluminum alloy 7012 subjected to fatigue test. Data were collected from tests conducted in the department of materials from two samples of aluminum alloy 7012 solubilized and precipitated by different time intervals and assayed temperature fatigue-type traction-compression, these data were then analyzed and used to survey curves using the base as E739. After lifting the curve analyzed the characteristics of the test samples and their correlation with the test results. We confirmed the effectiveness of the method of statistical analysis by ASME E739, which allowed the reading of data without this method would be very difficult to have a reading and comparison of the results for the two types... (Complete abstract click electronic access below)

Espondilomielopatia cervical caudal em cães: diagnóstico por imagem

The Caudal Cervical Spondylomyelopathy, also known as “Wobbler syndrome” is a neurological disorder that affects mainly breeds of large and giant size, especially Doberman pinsher and Great danes. Its aetiology is multifactorial and leads to a narrowing of the spinal canal by morphological and positional caudal cervical vertebrae (C5, C6 and C7), causing compression of the spinal cord and nerve roots. The clinical signs presented by the affected animals are progressive ataxia of hindlimbs and, later, the forelimbs, sometimes progressing to tetraparesis. Neck pain may be present. The diagnosis is made through the association of clinical signs and diagnostic imaging such as radiography, myelography, computed tomography and magnetic resonance imaging. According to the classification of the lesion obtained by imaging examinations, the conservative or surgical treatment is established and the prognosis is variable in accordance with the degree of affection of the spinal cord

Análise comparativa entre sistemas de resfriamento de injeção de plástico

This study aims to prove the economic feasibility of the installation of mechanical compression chillers on plastic injection molding machines in order to reduce the production cycle time of toothbrush cables in a specific case study. This evidence was confirmed by the comparative analysis of the system replaced and the new system installed. The old system had only one closed loop cooling tower which pumped chilled water to the injection molds, and the new system has the same tower sending cold water to the condensers of individual chillers installed on each injection machine. We conducted an analysis of energy efficiency in each system, showing that in terms of thermal efficiency virtually nothing has changed, but in terms of electricity demand the new system consumes 60.3 kW more. We conducted an analysis of machine productivity for both systems, showing a much higher productivity of the new system due to reduced cycle times caused by the presence of chillers and their greater cooling capacities. Equipped with data such as electricity rates, increases in operating costs and initial investments, the increase in consumption and demand of electricity plus the cycle time reduction were also calculated over so the simple payback 1 year and 2 months was reached