Determination of copper in fish feed by graphite furnace atomic absorption spectrometry using slurry sampling

The present work develops and optimizes a method to determine copper in samples of feces and fish feed by graphite furnace atomic absorption spectrometry (GFAAS) through the direct introduction of slurries of the samples into the spectrometer's graphite tube coated internally with metallic rhodium and tungsten carbide that acts as chemical modifiers. The limits of detection (LOD) and quantification (LOQ) calculated for 20 readings of the blank of the standard slurries (0.50% m/v of feces or feed devoid of copper) were 0.24 and 0.79 μg L -1 for the standard feces slurries and 0.26 and 0.87 μg L -1 for the standard feed slurries. The proposed method was applied in studies of absorption of copper in different fish feeds and their results proved compatible with that obtained from samples mineralized by acid digestion using microwave oven. © Springer Science+Business Media, LLC 2008.

Iron determination by FAAS in fish feed and feces after ultrasound-assisted extraction

This paper proposes a method to determine iron in samples of fish feed and feces using ultrasound in the extraction of the analyte and in subsequent quantification by flame atomic absorption spectrometry. Using HCl 0.10 mol L -1 as the extraction solution, the optimal conditions of extraction were found to be: granulometry of the sample <60 μm; a sonication time of five cycles of 10 s and sonication power of 136 W. The method was applied in studies of the availability of iron in four food sources used in the diet of Nile Tilapia. The results obtained with the proposed extraction method allowed us to calculate the coefficients of apparent digestibility of iron in the food sources, which was not possible when using results obtained from samples mineralized by acid digestion. © Springer Science+Business Media, LLC 2008.

Economic evaluation of nile tilapia juvenile production, feed with commercial ration and with primary production come from organic and inorganic fertilization

Study objective was to evaluate economically a Nile tilapia juvenile production, employing different feeding techniques. Tilapia fingerlings of 8g were stocked at 5 fish m-2 stocking in 50 and 150 m2 ponds, during 75 days. Treatments were: inorganic fertilization (P205 and N); organic fertilization (poultry manure) and commercial ration (32% CP). Water quality results were considered adequate for fish rearing. In juvenile production there were significant differences among treatments for individual final weight, medians were: for inorganic fertilization 12.92g (13.35g in 50 m2 and 12.49g in 150 m2); for organic fertilization 30.55g (33.69g in 50 m2 and 27.40g in 150 m2) and for commercial ration 51.23g (52.90g in 50 m2 and 50.15g in 150 m2). Survival rate ranged from 63 to 71%, with no statistic difference. Commercial ration was effective to bigger juvenile production, with a better market value. Costs considered in economic analyses were tilapia fingerlings, fertilizer, ration, labor and installation depreciation. Obtained information showed that juvenile production in 50 m2 ponds is not viable economically and, in 150 m2, production is viable only when commercial ration is used.

Performance of the CMS cathode strip chambers with cosmic rays

The Cathode Strip Chambers (CSCs) constitute the primary muon tracking device in the CMS endcaps. Their performance has been evaluated using data taken during a cosmic ray run in fall 2008. Measured noise levels are low, with the number of noisy channels well below 1%. Coordinate resolution was measured for all types of chambers, and fall in the range 47μm to 243μm. The efficiencies for local charged track triggers, for hit and for segments reconstruction were measured, and are above 99%. The timing resolution per layer is approximately 5 ns. © 2010 IOP Publishing Ltd and SISSA.

Passive vibration isolation using axially loaded curved beams

A nonlinear spring element of a vibration isolator should ideally possess high static and low dynamic stiffness. A buckled beam may be a good candidate to fulfil this requirement provided its internal resonance frequencies are high enough to achieve a wide frequency range of isolation. If a straight beam is used, there is a singularity in the force-displacement characteristic. To smooth this characteristic and eliminate the singularity at the buckling point, beams with initial constant curvature along their length are investigated here as an alternative to the buckled straight beam. Their force displacement characteristics are compared with different initial curvature and with a straight buckled beam. The minimum achievable dynamic stiffness with its corresponding static stiffness is compared for different initial curvatures. A case study is considered where the beams are optimized to isolate a one kilogram mass and to achieve a natural frequency of 1 Hz, considering small amplitudes of vibration. Resonance frequencies of the optimized beams for different curvature are presented. It is shown that an order of magnitude reduction in stiffness compared with a linear spring is achievable, while the internal resonance frequencies of the curved beam are high enough to achieve an acceptable frequency range of isolation.

Blends of cross-linked high amylose starch/pectin loaded with diclofenac

Polymers blends represent an important approach to obtain materials with modulated properties to reach different and desired properties in designing drug delivery systems in order to fulfill therapeutic needs. The aim of this work was to evaluate the influence of drug loading and polymer ratio on the physicochemical properties of microparticles of cross-linked high amylose starch-pectin blends loaded with diclofenac for further application in controlled drug delivery systems. Thermal analysis and X-ray diffractograms evidenced the occurrence of drug-polymer interactions and the former pointed also to an increase in thermal stability due to drug loading. The rheological properties demonstrated that drug loading resulted in formation of weaker gels while the increase of pectin ratio contributes to origin stronger structures. © 2012 Elsevier Ltd.

Meat quality of young Nellore bulls with low and high residual feed intake

Fifty-nine Nellore bulls from low and high residual feed intake (RFI) levels were studied with the objective of evaluating meat quality traits. Animals were slaughtered when ultrasound-measured backfat thickness reached 4. mm, and samples of Longissimus were collected. A mixed model including RFI as fixed effect and herd and diet as random effects was used, and least square means were compared by t-test. More efficient animals consumed 0.730. kg dry matter/day less than less efficient animals, with similar performance. No significant differences in carcass weight, prime meat cuts proportion, chemical composition, pH, sarcomere length, or color were observed between RFI groups. Shear force, myofibrillar fragmentation index and soluble collagen content were influenced by RFI, with a higher shear force and soluble collagen content and a lower fragmentation index in low RFI animals. Feedlot-finished low RFI young Nellore bulls more efficiently convert feed into meat, presenting carcasses within quality standards. © 2012 Elsevier Ltd.

Experimental study of bottom feed updraft gasifier

The updraft biomass gasifiers currently available produce a gas with high tar content. For almost all downstream applications a substantial reduction of the tar concentration is required. The gravimetric tar concentration behavior in producer gas, obtained at a modified updraft fixed bed gasifier, was studied. The feedstock feeding system was modified respect to the traditional updraft gasification design in order to decrease the tar concentration in the producer gas; the material is feeding continuously through a conduit in the base of the reactor over the grate. The caloric power of the syngas obtained was slightly lower than the typical value for this type of reactor and the highest efficiency obtained for the woodchip gasification was 77%. The highest tar concentration obtained during the experiments was 1652.7 mg N m-3 during the first our of experiments, comparable with the smaller value reported for the updraft reactors, this value is reduced significantly after the stabilization of the gasification process in the reactor. The smaller value obtained was 21 mg N m-3. © 2013 Elsevier Ltd.

Development of a new method to prepare nano-/microparticles loaded with extracts of azadirachta indica, their characterization and use in controlling plutella xylostella

Biodegradable nanoparticles have been widely explored as carriers for controlled delivery of therapeutic molecules; however, studies describing the development of nanoparticles as carriers for biopesticide products are few. In this work, a new method to prepare nanoparticles loaded with neem (Azadirachta indica) extracts is presented. In this study, nanoparticles were formulated as colloidal suspension and (spray-dried) powder and characterized by evaluating pH, particle size, zeta potential, morphology, absolute recovery, and entrapment efficiency. A high-performance liquid chromatography method was used for nanoparticle characterization. The best formulations presented absolute recovery and entrapment efficiencies of approximately 100% and a release profile based on swelling and relaxation of the polymer or polymer erosion. The biological data of the formulated products against Plutella xylostella showed 100% larval mortality. The nanoparticle information improved the stability of neem products against ultraviolet radiation and increased their dispersion in the aqueous phase. © 2013 American Chemical Society.

Ultrasound-assisted extraction of Na and K from swine feed and its application in a digestibility assay: A green analytical procedure

The study is aimed to evaluate the efficiency of ultrasound-assisted extraction (UAE) as a simple strategy focused on sample preparation for metal determination in biological samples. The extraction of sodium and potassium extraction was carried out from swine feed followed by determination of the concentration of these metals by flame atomic emission spectrometry (FAES). The experiment was performed to cover the study of the variables influencing the extraction process and its optimal conditions (sample mass, particle size, acid concentration, sonication time and ultrasound power); the determination of these analytical characteristics and method validation using certified reference material; and the analysis of pre-starter diets. The optimal conditions established conditions were as follows: mass: 100 mg, particle size:<60 μm, acid concentration: 0.10 mol L-1 HCl, sonication time: 50 s and ultrasound power: 102 W. The proposed method (UAE) was applied in digestibility assays of those nutrients present in different piglet pre-starter feeds and their results proved to be compatible with those obtained from mineralized samples (P < 0.05). The ultrasound extraction method was demonstrated to be an excellent alternative for handless sampling and operational costs and the method also has the advantage of does not generating toxic residues that may negatively affect human health and contaminate the environment. © 2013 Elsevier B.V. All rights reserved.

Estudo da usinagem em torneamento da superliga a base de niquel NIMONIC 80

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Desorption of heavy metals from ion exchange resin with water and carbon dioxide

Adsorption and regeneration of ion exchange resins were studied using a subcritical solution of a CO₂-H₂O mixture and a fixed bed column. The commercial Amberlite IRC-50/IRC-86 cation exchange resins and Amberlite IRA-67 anion exchange resin were tested for heavy metals (Pb, Cu, Cd) adsorption from a solution with different initial metal concentrations at different temperatures. After adsorption, the loaded resins were regenerated with water and carbon dioxide at different temperatures and a pressure of 25 MPa. The efficiency of the IRC-50 resin was lower than that of the IRC-86 resin for the adsorption of metals like Cd, Cu and Pb. Results obtained for desorption of these metals indicated that the process could be used for Cd and in principle for Cu. Sorption of metal ions depended strongly on feed concentration. Mathematical modeling of the metal desorption process was carried out successfully as an extraction process. For this purpose, the VTII Model, which is applied to extraction from solids using supercritical solvents, was used in this work.

Evaluation of babassu meal in feed for layer hens during the growth phase

Studies were conducted to evaluate the nutritional value and inclusion levels of babassu meal (BM) in the diet of grower layer pullets in substitution to wheat meal. Digestibility, metabolism and growth trials were conducted. Twelve cecectomized roosters were used in the digestibility assay to determine the coefficients of standardized digestibility of amino acids (CSDAA). The metabolism trial was conducted with 30 adult roosters to determine the apparent metabolizable energy corrected for nitrogen (AMEn) of BM. A growth trial was performed to determine replacement levels of wheat midds by BM diet using 360 six-week-old commercial layer pullets. BM was included at the 0, 75 and 150 g/kg of BM, during grower and development rearing phases, respectively. Feed intake, body weight gain, and feed conversion were evaluated. BM AMEn was determined as 1,474 kcal/kg, on as-fed basis. The CSDAA determined for BM were below 88% for all AA. The inclusion of BM in the feed of grower layers (7-18 week) significantly decreased feed intake (p < 0.05), but significantly improved body weight gain and feedconversion ratio (p < 0.05) at 15% inclusion level. Considering the nutritional value and performance results, BM can replace wheat midds in diets of grower layer pullets.

Dietary fiber inclusion as an alternative to Feed Fasting to induce molting in Commercial Layers

The objective of the present experiment was to compare the performance, egg quality and organ morphometrics of commercial layers submitted to alternative forced molting methods using dietary fibers. The experimental period included the phases of molting, rest, and second laying cycle (six periods of 28 days each). In the trial, 320 commercial Isa Brown layers with 72 weeks of age were distributed, according to a completely randomized experimental design into five treatments with eight replicates of eight birds each, totaling 40 experimental units. Molting was induced by feeding diets with the inclusion of alfalfa or soybean husks at 80% and 60% or feed fasting. Treatments were applied for 14 days. Performance and egg quality parameters were evaluated for the second laying cycle and organ morphometrics (liver, gizzard, proventriculus, reproductive apparatus) in two different slaughter dates. The obtained data were submitted to analysis of variance using the General Linear Model (GLM) procedure of SAS statistical package (SAS Institute, 2002). Alternative molting methods promoted similar performance and egg quality results after molting were similar to those obtained by the conventional fasting method. Feeding fiber produced the expected effects in terms of organ weight regression and recovery and may be used to induce molting in commercial layers.