Gene amplified in oesophageal cancer 1 (GAEC1) amplification in colorectal cancers and its impact on patient's survival

GAEC1 (gene amplified in oesophageal cancer 1) is located at 7q22.1, first identified in oesophageal cancer.1 Initial work indicated that GAEC1 can act as an oncogene.2 Our pilot study found ���80% of colorectal cancers showing amplification of GAEC1.3 In this research, we will study GAEC1 copy number in colon cancer cell lines and colorectal tissues, and its prognostic significance. Two human colon cancer cell lines (SW480 and SW48) and one normal colonic epithelial cell line (FHC) were obtained from American Type Culture Collection. Culturing conditions for these cell lines were as published previously.4 Tissues were collected from 283 patients (213 Australian; 70 Japanese) diagnosed with colorectal cancers. Ninety surgically removed non-cancer colorectal tissues (diverticular diseases, hyperplastic polyps and volvulus) were used as controls. H&E stained sections from each cancer were checked to select a block with sufficient cancer tissue and representative morphological features for each patient for DNA extraction...

A C-ITS based lane-changing advisory for weaving sections

Weaving sections, a common design of motorways, require extensive lane-change manoeuvres. Numerous studies have found that drivers tend to make their lane changes as soon as they enter the weaving section, as the traffic volume increases. Congestion builds up as a result of this high lane-changing concentration. Importantly, such congestion also limits the use of existing infrastructure, the weaving section downstream. This behaviour thus affects both safety and operational aspects. The potential tool for managing motorways effectively and efficiently is cooperative intelligent transport systems (C-ITS). This research investigates a lane-change distribution advisory application based on C-ITS for weaving vehicles in weaving sections. The objective of this research is to alleviate the lane-changing concentration problem by coordinating weaving vehicles to ensure that such lane-changing activities are evenly distributed over the existing weaving length. This is achieved by sending individual messages to drivers based on their location to advise them when to start their lane change. The research applied a microscopic simulation in AIMSUN to evaluate the proposed strategy���s effectiveness in a one-sided ramp weave. The proposed strategy was evaluated using different weaving advisory proportions, traffic demands and penetration rates. The evaluation revealed that the proposed lane-changing advisory has the potential to significantly improve delay.

A comparative investigation of C6-C15 hydrocarbons emitted from a passenger car powered by unleaded petrol and 10% ethanol fuel

Twenty-three non-methane hydrocarbons were captured from the exhaust of a car operating on unleaded petrol (ULP) and 10% ethanol fuels at steady speed on a chassis dynamometer. The compounds were identified and quantified by GC/MS/FID and their emission concentrations at 60 km/h, 80km/h and idle speed were evaluated. The most abundant compounds in the exhaust included n-hexane, n-heptane, benzene, toluene, ethyl benzene, m- and p-xylenes, and methylcyclopentane. Because of the large number of compounds involved, no attempt was made to compare the emission concentrations of the compounds. Rather the sum of the emission concentrations for the suite of compounds identified was compared when the car was powered by ULP and 10% ethanol fuel. It was evident from the results that the emission concentrations and factors were generally higher with ULP than with 10% ethanol fuel. The total emission concentrations with the ULP fuel were 2.8, 4.2 and 2.6 times the corresponding values for the 10% ethanol fuel at 60km/h, 80km/h and idle speed, respectively. The implications of the results on the environment are discussed in the paper.

Postmodern Theory and the Choreography of Michael Clark

This study addresses two interrelated questions: Can postmodern ���theory��� illuminate an understanding of Michael Clark���s work? and, a sub-question, In which ways, if at all, does Clark���s work demonstrate a postmodern sensibility? Chapter one, the introduction to this study, provides a ���portrait��� of postmodernism, that is, it addresses the question What is postmodernism? Chapter two is a biography of Michael Clark. The seminal sections to this study, however, are chapters three and four. Here the author blends a discussion of a) subject matter, treatment and meanings in Clark���s choreography, b) journalistic criticisms of those features of his work, and c) postmodern theory. The outcome of these chapters is to demonstrate that Clark���s works do indeed require re-interpretation and re-evaluation, and to illustrate how these factors might be achieved.

Desalination with a solar-assisted heat pump : an economic optimization

The solar-assisted heat pump (SAHP) desalination, based on the Rankin cycle, operates in low temperature and utilizes both solar and ambient energy. An experimental SAHP desalination system has been constructed at the National University of Singapore, Singapore. The system consisted of two main sections: an SAHP and a water distillation section. Experiments were carried out under the different meteorological condition of Singapore and results showed that the system had a performance ratio close to 1.3. The heat pump has a coefficient of performance of about 8, with solar collector efficiencies of 80% and 60% for evaporator and liquid collectors, respectively. Economic analysis showed that at a production rate of 900 L/day and an evaporator collector area of around 70m2 will have a payback period of about 3.5 years.

Human resource management and entrepreneurship : building theory at the intersection

In 2008 we brought together much work at the intersection of entrepreneurship and human resource management (HRM) (Barrett & Mayson, 2008), after calls for more research (Baron, 2003; Katz, Aldrich, Welbourne & Williams, 2000; Tansky & Heneman, 2003). More has been collated since (Soriano, Dobon & Tansky, 2010; Tansky, Soriano & Dobon, 2010). We think it is now time again to regroup, pull conversational threads together and have a critical look at recent research at the intersection of HRM and Entrepreneurship. As editors of International Handbook of Entrepreneurship and HRM (Barrett & Mayson, 2008) we were privileged to collect 23 wonderfully diverse chapters from scholars around the globe addressing a range of issues at the intersection of the two pertinent disciplines or fields: HRM and entrepreneurship. This edition represented a coalescing of ideas that had been swirling about for some time. In three sections, the first dealt with theory and research methods, the second with the nature of HRM in small and entrepreneurial firms and the third with the functional aspects of HRM. At the time we were aware that the handbook did not cover the entire field and many topics were left unexplored. For example, the topic of regulation was generally absent while issues such as career advancement, performance management, organisational change and gender, diversity and ethnicity were also missing. In essence, the majority of those contributions sought to develop an understanding of the context in which particular aspects of HRM can be played out.

���My hands are plunged in oranges������: an experiential account of a working process

This presentation incorporated the live performance throughout, by the author, of movement from ���The All Weather Project��� by Liz Roche. Movement sections are indicated by italics. ���I am going to start by dancing for you��� Movement: Live performance of solo approximately 10 minutes in duration This is the introduction... Through my PhD research, I am examining the choreographic process from the perspective of the independent contemporary dancer, through embodying this role as a researcher/participant. My methodological frameworks, which utilise video documentation and journal writing, could be characterised as ethnographic, multi-modal embodied theorising, leading to ���multi-dimensional theorising��� (I adopt this term from Susan Melrose). In this way, I am unwinding the embodied practice of dancing, through the co-existent layers of experience, towards forming a theoretical understanding of the issues that arise for the dancer. The issues that I have identified as relevant to my research are those relating to the dancer���s ���moving identity��� or way of moving, as a mutable and adaptable form that must alter and re-adjust to each different choreographic engram or movement vocabulary, that she/he encounters. I am examining this interplay between stability and change. I also reflect on the impact of destabilisation and flux on the dancer���s identity in a wider sense, as she/he relates outwardly to signifying factors within the social strata. Today I am going to bring you through a reflection on the working process of a dance piece as experienced from the inside. By doing so, I hope to capture and elucidate the multi-dimensional layers which existed for me within this process. Through displaying these fragments together, I endeavour to invoke the ���totality��� of the experience...

Experimental and numerical studies of fire exposed lipped channel columns subject to distortional buckling

Cold-formed steel sections are commonly used in low-rise commercial and residential buildings. During fire events, cold-formed steel structural elements in these buildings are exposed to elevated temperatures. Hence after such events there is a need to determine the residual strength of these structural elements. However, only limited information is available in relation to the residual strength of fire exposed cold-formed steel members. This research is aimed at investigating the residual distortional buckling capacities of fire exposed cold-formed steel lipped channel sections. A series of compression tests of fire exposed, short lipped channel columns made of varying steel grades and thicknesses was undertaken in this research. Test columns were exposed to different elevated temperatures up to 800 oC. They were then allowed to cool down at ambient temperature before they were tested to failure. Suitable finite element models of tested columns were also developed and validated using test results. The residual compression capacities of tested columns were predicted using the ambient temperature cold-formed steel design rules (AS/NZS 4600, AISI S100 and Direct Strength Method). Post-fire mechanical properties obtained from a previous study were used in this study. Comparison of results showed that ambient temperature design rules for compression members can be used to predict the residual compression capacities of fire exposed short or laterally restrained cold-formed steel columns provided the maximum temperature experienced by the columns can be estimated after a fire event. Such residual capacity assessments will allow structural and fire engineers to make an accurate prediction of the safety of buildings after fire events. This paper presents the details of these experimental and numerical studies and the results.

Web crippling studies of Duragal channel sections ��� ETF and ITF load cases

Cold-formed steel members have many advantages over hot-rolled steel members. However, they are susceptible to various buckling modes at stresses below the yield stress of the member because of their relatively high width-to-thickness ratio. Web crippling is one of the failure modes that can occur when the members are subjected to transverse high concentrated loadings and/or reactions. The four common loading conditions are the end-one-flange (EOF), interior-one-flange (IOF), end-two-flange (ETF) and interior-two-flange (ITF) loadings. Recently a new test method has been proposed by AISI to obtain the web crippling capacities under these four loading conditions. Using this test method 38 tests were conducted in this research to investigate the web crippling behaviour and strength of channel beams under ETF and ITF cases. Unlipped channel sections having a nominal yield stress of 450 MPa were tested with different web slenderness and bearing lengths. The flanges of these channel sections were not fastened to the supports. In this research the suitability of the current design rules in AS/NZS 4600 and the AISI S100 Specification for unlipped channels subject to web crippling was investigated, and suitable modifications were proposed where necessary. In addition to this, a new design rule was proposed based on the direct strength method to predict the web crippling capacities of tested beams. This paper presents the details of this experimental study and the results.

Experimental studies on web crippling behaviour of hollow flange channel beams under two flange load cases

This paper presents the details of an experimental study of a cold-formed steel hollow flange channel beam known as LiteSteel beam (LSB) subject to web crippling under End Two Flange (ETF) and Interior Two Flange (ITF) load cases. The LSB sections with two rectangular hollow flanges are made using a simultaneous cold-forming and electric resistance welding process. Due to the geometry of the LSB, and its unique residual stress characteristics and initial geometric imperfections, much of the existing research for common cold-formed steel sections is not directly applicable to LSB. Experimental and numerical studies have been carried out to evaluate the behaviour and design of LSBs subject to pure bending, predominant shear and combined actions. To date, however, no investigation has been conducted on the web crippling behaviour and strength of LSB sections. Hence an experimental study was conducted to investigate the web crippling behaviour and capacities of LSBs. Twenty-eight web crippling tests were conducted under ETF and ITF load cases, and the ultimate web crippling capacities were compared with the predictions from the design equations in AS/NZS 4600 and AISI S100. This comparison showed that AS/NZS 4600 and AISI S100 web crippling design equations are unconservative for LSB sections under ETF and ITF load cases. Hence new equations were proposed to determine the web crippling capacities of LSBs based on experimental results. Suitable design rules were also developed under the direct strength method (DSM) format.

Experimental investigation and design of lipped channel beams in shear

Cold-formed high strength steel members are increasingly used as primary load bearing components in low rise buildings. Lipped channel beam (LCB) is one of the most commonly used flexural members in these applications. In this research an experimental study was undertaken to investigate the shear behaviour and strengths of LCB sections. Simply supported test specimens of back to back LCBs with aspect ratios of 1.0 and 1.5 were loaded at mid-span until failure. Test specimens were chosen such that all three types of shear failure (shear yielding, inelastic and elastic shear buckling) occurred in the tests. The ultimate shear capacity results obtained from the tests were compared with the predictions from the current design rules in Australian/NewZealand and American cold-formed steel design standards. This comparison showed that these shear design rules are very conservative as they did not include the post-buckling strength observed in the shear tests and the higher shear buckling coefficient due to the additional fixity along the web-flange juncture. Improved shear design equations are proposed in this paper by including the above beneficial effects. Suitable lower bound design rules were also developed under the direct strength method format. This paper presents the details of this experimental study and the results including the improved design rules for the shear capacity of LCBs. It also includes the details of tests of LCBs subject to combined shear and flange distortion, and combined bending and shear actions, and proposes suitable design rules to predict the capacities in these cases.

Class notes : 10 principles of good BPM

The question concerning what makes for good BPM is often raised. A recent call from Paul Harmon on the BPTrends Discussion LinkedIN Group for key issues in BPM received 189 answers within two months, with additional answers still appearing. I have teamed up with a number of BPM researchers and practitioners to bring together our joint experience in a BPM workshop at the University in Liechtenstein in 2013, where we developed ten principles of good BPM, later published in Business Process Management Journal (vom Brocke et al., 2014). The paper, which has received considerable attention in academia, was ranked the journal���s most downloaded paper the month it was published. Slides on Slideshare that provide a brief summary of the paper have been accessed more than 3,000 times since they were first put online in March 2014. Given the importance of the topic���what makes for good BPM���and the positive response to the ten principles, I wrote this note with the co-authors of the original BPMJ paper to outline the ten principles and illustrate how to use them in practice. We invite all readers to engage in this discussion via any channel they find appropriate.

Innate transcriptional networks activated in bladder in response to uropathogenic Escherichia coli drive diverse biological pathways and rapid synthesis of IL-10 for defense against bacterial urinary tract infection

Early transcriptional activation events that occur in bladder immediately following bacterial urinary tract infection (UTI) are not well defined. In this study, we describe the whole bladder transcriptome of uropathogenic Escherichia coli (UPEC) cystitis in mice using genome-wide expression profiling to define the transcriptome of innate immune activation stemming from UPEC colonization of the bladder. Bladder RNA from female C57BL/6 mice, analyzed using 1.0 ST-Affymetrix microarrays, revealed extensive activation of diverse sets of innate immune response genes, including those that encode multiple IL-family members, receptors, metabolic regulators, MAPK activators, and lymphocyte signaling molecules. These were among 1564 genes differentially regulated at 2 h postinfection, highlighting a rapid and broad innate immune response to bladder colonization. Integrative systems-level analyses using InnateDB (http://www.innatedb.com) bioinformatics and ingenuity pathway analysis identified multiple distinct biological pathways in the bladder transcriptome with extensive involvement of lymphocyte signaling, cell cycle alterations, cytoskeletal, and metabolic changes. A key regulator of IL activity identified in the transcriptome was IL-10, which was analyzed functionally to reveal marked exacerbation of cystitis in IL-10���deficient mice. Studies of clinical UTI revealed significantly elevated urinary IL-10 in patients with UPEC cystitis, indicating a role for IL-10 in the innate response to human UTI. The whole bladder transcriptome presented in this work provides new insight into the diversity of innate factors that determine UTI on a genome-wide scale and will be valuable for further data mining. Identification of protective roles for other elements in the transcriptome will provide critical new insight into the complex cascade of events that underpin UTI.

The effects of exercise and adipose tissue lipolysis on plasma adiponectin concentration and adiponectin receptor expression in human skeletal muscle

Objective It has been suggested that adiponectin regulates plasma free fatty acid (FFA) clearance by stimulating FFA uptake and/or oxidation in muscle. We aimed to determine changes in plasma adiponectin concentration and adiponectin receptor 1 and 2 mRNA expression in skeletal muscle during and after prolonged exercise under normal, fasting conditions (high FFA trial; HFA) and following pharmacological inhibition of adipose tissue lipolysis (low FFA trial; LFA). Furthermore, we aimed to detect and locate adiponectin in skeletal muscle tissue. Methods Ten subjects performed two exercise trials (120 min at 50% VO2max). Indirect calorimetry was used to determine total fat oxidation rate. Plasma samples were collected at rest, during exercise and during post-exercise recovery to determine adiponectin, FFA and glycerol concentrations. Muscle biopsies were taken to determine adiponectin protein and adiponectin receptor 1 and 2 mRNA expression and to localise intramyocellular adiponectin. Results Basal plasma adiponectin concentrations averaged 6.57��0.7 and 6.63��0.8 mg/l in the HFA and LFA trials respectively, and did not change significantly during or after exercise. In the LFA trial, plasma FFA concentrations and total fat oxidation rates were substantially reduced. However, plasma adiponectin and muscle adiponectin receptor 1 and 2 mRNA expression did not differ between trials. Immunohistochemical staining of muscle cross-sections showed the presence of adiponectin in the sarcolemma of individual muscle fibres and within the interfibrillar arterioles. Conclusion Plasma adiponectin concentrations and adiponectin receptor 1 and 2 mRNA expression in muscle are not acutely regulated by changes in adipose tissue lipolysis and/or plasma FFA concentrations. Adiponectin is abundantly expressed in muscle, and, for the first time, it has been shown to be present in/on the sarcolemma of individual muscle fibres.