Redução de consumo de energia eletrica a partir de reaproveitamento de energia termica com uso de ciclo rankine orgânico

This paper is proposed the usage of an Organic Rankine Cycle (ORC) along with waste heat recovery from an inconstant heat source. This method of waste heat recovery with intermittent heat source is part of a technical viability study. This paper also brings up the usage of thermal energy storage as heat source for the ORC. This paper is based on a heat treatment company study in which a natural gas furnace is explored. Data such as mass flow, temperature and specific waste gas heat from this furnace are used through calculations. Calculations are made also based on furnace cycles. This viability study considers a series of working fluids such as ammonia, benzene, R113 and R134a. Results point out that ORC with out thermal storage and using refrigerant fluid ammonia is the best alternative

Modelagem em 3D de uma patela humana e análise de esforços utilizando o método dos elementos finitos

Throughout the history of medicine surgeons realized the importance of the patella to the functioning of the knee. The main function of the patella is to increase the mechanical efficiency of the quadriceps tendon and knee extensor mechanism. It was found that 50% to 80% of the fractures without deviation of the patella have the transversal pattern, possibly due to excessive tensile forces applied to the extensor mechanism. The purpose of this study is to analyze the loads to which a patella is submitted during a normal extension movement of knee. This analysis will be done by modeling a 3D patella and subsequent load simulation as, described in medical literature, using the finite element method

Investigação do tratamento de água de máquina de lavar roupa empregando reator biológico, em escala piloto, visando redução da concentração de fósforo para reúso não potável

This research aims at the study of treatment of clothes washing water through biological treatment, for the purpose of evaluating the reduction of phosphorus to make it suitable for a posterior treatment of physical-chemical. For this purpose it was employed a sequencing batch reactor, consisting of aerobic and anaerobic phases. During the project it was verified not only the reduction of phosphorus (removal of 30 to 50%) but also the reduction of BOD, COD, Turbidity and Nitrate (removal of 38 to 36%, 34 to 41%, 72,3 to 75% and 57,8 to 60% respectively), which demonstrates that the proposed treatment can assist advanced treatments of water for its non potable reuse

Redução bacteriana via terapia fotodinâmica

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Estudo de caso: aplicação do método DMAIC-White Belt- na redução de latas amassadas em uma produção de leite em pó

This work consists of the implementation of the steps Define, Measure , Analyze , Improve and Control ( DMAIC ) to develop a Six Sigma project in an industry the food industry. The objective was to demonstrate a potential for reducing the occurrence of crushed cans in potting milk powder industry in a White Belt project. The food industry accounts for about 9 % of Brazil's gross domestic product ( GDP ), generating thousands of jobs . Among the major sectors of the food industry is the manufacturing sector of milk , occupies approximately 10 % of the total turnover of the food industry . Brazil is considered today one of the eight largest producers of milk powder in the world. The milk powder is packed , mostly for aluminum cans that are lined internally with varnishes and other materials to protect the milk of metals from aluminum. When the cans are dented food protection is compromised and may lead ingestion causing dis-eases such as botulism. Aiming to solve the problem of dented cans methodology was used as a case study with a quantitative approach through the DMAIC method. Some quality tools used in each step of the project as brainstorming , cause and effect diagram , flowchart , ef-fort and impact matrix, 5W1H , among other Pareto diagram is presented . A survey about the disposal of cans in the company verifying a mean loss and, from this histor-ical , a goal loss was calculated was performed . With the target set we calculated the annual saving design . During application of DMAIC was found that the highest rate of loss occurred in transportation between the factory and the factory that fills cans milk . Several actions were taken to resolve problems that resulted in dented cans and the first two months of phase control it was found that the smaller losses calculated target resulting in a saving for the company. The short time of implementa-tion of the Improve phase did not allow a more detailed a ...

Modelos de tratamento para adenocarcinomas de próstata tratados por radioterapia conformacional 3D

Radiotherapy is a branch of medical physics related to the treatment of malignant neoplasm, being an important instrument in the fight against cancer, when combined with the effort of a multidisciplinary team, composed of, physicians, physicists, nurses and technicians. Every year more than 3.5 million new cases of cancer are recorded in the world, being the prostate cancer responsible for approximately 25% of this amount (INCA and IARC, 2008). In this type of cancer, radiotherapy is a method indicated for treatement. The technological advance in this area over years has allowed a greater accuracy in the tumor location, more conformation of the radiation beam around the tumor, reducing the dose in healthy tissues and a consequent dose increase on treatment (Bedford et al., 1999). A radiotherapy planning, in which the physicist develops an important role, is composed of several steps, including choosing the best configuration of treatment beams. This choice has a close relationship with success of therapy and is critical to achieve the best distribution of dose inside the tumor and expose the least as possible the healthy tissue to radiation. In this work, two options for setting up camps in the first phase in a treatment of prostate cancer were simulated in computer planning: 4 fields orthogonal or “Box” with gantry angles in 00, 1800, 2700 e 90° and 4 fields angled or “X” (1350, 450, 3150 e 2250). The percentage of the rectal volume exposed to 40, 50, 60, 72 and 76 Gy should be limited to 60, 50, 25, 15 and 5% respectively (Greco et al., 2003). The femoral toxicity have limited dose by 70% of the total dose prescribed in a prostate treatment (Bedford et al., 1999). The planning of 27 patients with prostate adenocarcinoma submitted to 3D conformal radiotherapy were accompanied. As a result, it was assessed that the best TCP (tumor control probability)... (Complete abstract click electronic access below)

Utilização do método de tomada de decisão multicritério PROMETHEE II para priorização do plano de ação de redução de custos de manutenção

In the last years, the maintenance took an essential role inside the productive system. Plan and manage the maintenance actions in an efficient way, are vital activities for higher production availability. This paper presents an application of a Multicriteria Decision Analysis method in a chemical industry, willing to priories a plan action for the reduction of the maintenance cost. The method used was the PROMETHEE II, with it the results were obtained through the softwares Microsoft Excel and Decision Lab

Projeto DMAIC com ferramentas six sigma para redução de custos logísticos de uma multinacional

This work has a focus on project execution DMAIC ( Define Measure Analyze Implement Control) , using the statistical and quality tools to identify , analyze and implement improvements in a given process in order to reduce costs telephony transport of a multinational consumer goods . The multinational consumer goods to be studied has outsourced carriers who perform the distribution of its products , which may lead them straight to their factories or one of its distribution centers to the points of sale ( supermarkets , bakeries , gas stations , convenience cafeterias , among others ) . Whenever there is an unexpected situation or some problem at the time of delivery of the goods to the customer opens an occurrence , ie , the carrier responsible for contacts ( 0800 ) with the contact center company of consumer goods which in turn registers the occurrence, analyzes and sends a response action to the carrier . This work will study the problem with a high number of connections to handle occurrence , through analysis and data collection , identify improvement opportunities, implement them and monitor the results to ensure that the gain and loss reduction are sustainable

Análise da influência da iluminação de rodovias federais com a redução do número de acidentes

The increasing rate of traffic accidents, followed by the high rate of mortality due to these occurrences, favored to the classification of traffic accidents as a public health problem in Brazil. These accidents consume a significant portion of Gross Domestic Product (GDP), especially related to the victims. Considering this scenery with many tragedies and resources being spent only in the end, this paper seeks to examine the influence of federal highways lighting by reducing the number of accidents. Federal Highways sections that received lighting were taken up for study, therefore a survey of statistical data has been raised considering the accidents before and after the route had been illuminated. Taking advantage of the results obtained, an economic analysis has been made considering the amounts consumed by traffic accidents versus the values required for the installation of lighting on highways

Redução do tempo de ciclo baseado na produção enxuta em uma rémontagem de tubos de freios e combustível

In today's competitive environment of automakers, it is essential to obtain the highest efficiency of the production process. This paper presents a study in a pre-assembly of brake pipes and fuel of a vehicle where the value stream maps and information (VSM – Value Stream Mapping) were designed in order to improve the process by reducing the Lead Time Production of a product, reducing waste and decrease time between processes. This work can be divided into three stages, the first building the VSM of the initial state, the second VSM of the proposed state and finally the VSM than was actually performed and to present the gains were achieved effectively. The proposed VSM would lead to a gain of 54% in lead time and 61% in processing time, since the VSM implemented had gains of 47% in lead time and 48% in processing time even without major investments as originally proposed. Concluding that even without big investment, using the techniques of lean manufacturing is possible to achieve high levels of process efficiency

Melhoria do nível de serviço no atendimento ao cliente por meio da estrutura direta de distribuição Transit Point

Increasingly competitive markets have driven the search for companies in many different ways to win and keep customers. The service level is basically the performance of companies in fulfilling the orders made, or how companies demonstrate to their clients efforts in their behalf. This work aims to solve the difficulties faced by a multinational company present in Brazil, in the distribution of its products in the category Ice Cream in order to improve the service level of their customers. Review the logistics network and concepts related to the distribution system of products is one of several ways to achieve this goal, as well as the use of IT and tools to assist in planning and programming of the physical distribution of products. In this study we used the concept of direct distribution system called Transit Point (TP). The TP provides at the same time, a strategy of rapid response, flexibility, low transportation costs and no inventory. A router - software capable of simulating the actual conditions experienced in the daily distribution - was used to assist in calculations. Results showed reductions of up to 47.5% in transportation costs and better conditions were provided in the distribution of products, positively impacting on service levels and in the maintenance of products quality, with a reduction of 1.6% of the total costs involve

Modelagem e simulação do mecanismo biela manivela e análise estrutural de biela automotiva

Nowadays, the automotive industry is working to optimize the design of engines, in order to reduce the fuel consumption with acceptable efficiency ratio. This undergraduate thesis is aimed at perform a kinematic/dynamic analysis of a slider-crank mechanism that is part of a four stroke internal combustion engine, the same engine that was used in the analysis described by Montazersadhd and Fatemi (2007). Two algorithms were developed based on Kane’s method to calculate velocities and accelerations of the mechanism bodies, and provide the acting forces at connecting rod joints. A SimMechanics model was developed to simulate the engine, and monitoring the same parameters that were calculated with the algorithms. The results obtained with both approaches were satisfactory and showed good agreement with the values provided by Montazersadhd and Fatemi (2007). The obtained results showed that the axial component of the rod joint efforts was caused by the pressure exerted on the piston head,whereas the radial component was related with the action of inertia loads. Besides, this thesis presents a connecting rod assembly mesh that is going to be used for static and fatigue finite element analysis in the future

Estudo dos micronutrientes na produção de ramnolipídios por mutante de Pseudomonas aeruginosa LBI

Os biossurfactantes apresentam inúmeras vantagens, como baixa toxicidade, biodegradabilidade e alta estabilidade, mas não são amplamente utilizados devido ao custo de produção. A utilização de substratos baratos, linhagens mutantes que associados à otimização das condições de cultivo pode levar a uma redução nos custos, possibilitando assim a substituição dos surfactantes sintéticos pelos biológicos. Uma maneira empregada para maximizar a produção dos biossurfactantes é a limitação de nutrientes. Os esforços empregados nesse sentido são direcionado para as proporções carbono: nitrogênio, entretanto os efeitos dos elementos traços são pouco conhecidos. Devido a esses fatores, o presente trabalho avaliou a importância dos seguintes elementos traços: ferro, zinco, cobalto, cobre, manganês e do sal citrato de sódio dihidratado, nas fermentações realizadas utilizando o mutante de Pseudomonas aeruginosa LBI 2A1. Para tanto foram realizadas fermentações em frascos Erlenmeyer, onde se utilizou diferentes concentrações desses elementos. A influência dos mesmos na produção de ramnolipídios foi constatada, uma vez que a produção desse biotensoativo foi aumentada em mais de três vezes alterando apenas a concentração de um único elemento traço (Fe). Os experimentos realizados permitem, também, inferir a respeito das melhores concentrações desses micronutrientes para a produção de ramnolipídios

Redução do tempo de setup de máquinas de usinagem em uma industria automobilística

Continuous improvement of industrial processes is one way to become companies more competitive in the market. For this, a fairly widespread use is the methodology of lean production systems, by eliminating waste. One of the tools of these systems is the method of rapid exchange of die or also called SMED, which will be applied in this study. The study aims to develop proposals for reducing the time of set up of two machines in two machining lines, watching also the ergonomics and safety conditions in this operations. The set up time reduction is justified among others, due to increase the machine productivity. In applying the connecting rod machining line, there were two types of exchange. Reductions in time to set up proposals reached values of 47% to one of them, and 55% to the other. It is important to underline that to reach this result, there was no need for large investments. In the application in block machining line, was developed an improvement in the ergonomic area. It was placed a pulley block that came to increase the time of tool change. Aiming to improve the security of the exchange, without productivity loss, the method was applied to reduce this time. It was developed two proposals.: the first would reduce that time by 19%, and does not require many resources of the company. The second involves the parallelization of the exchange, so that the reduction is 48%. However, this proposal requires one more manpower at the time of exchange and it is not always possible

Redução de tempo de setup de uma máquina de encartuchamento pela técnica SMED

Currently the market requires companies to adapt for they can have the lowest possible cost in their manufacturing, be it a good or service, thus obtaining a greater profit. For this profit the Toyota Production System applies lean manufacturing practices actions with reduced spending, smaller lots and stocks, generated by market demand. The technique allows SMED with few actions, changes and investments that time does not exceed one digit on your total time. This case study shows that only with standardization and use of inexpensive improvements, could reduce setup time on a machine for 70 minutes to time of approximately 48 minutes with little investment, demonstrating the viability of the tool presented