A Novel Micro- and Nano-Scale Positioning Sensor Based on Radio Frequency Resonant Cavities

In many micro- and nano-scale technological applications high sensitivity displacement sensors are needed, especially in ultraprecision metrology and manufacturing. In this work a new way of sensing displacement based on radio frequency resonant cavities is presented and experimentally demonstrated using a first laboratory prototype. The principle of operation of the new transducer is summarized and tested. Furthermore, an electronic interface that can be used together with the displacement transducer is designed and proved. It has been experimentally demonstrated that very high and linear sensitivity characteristic curves, in the range of some kHz/nm; are easily obtainable using this kind of transducer when it is combined with a laboratory network analyzer. In order to replace a network analyzer and provide a more affordable, self-contained, compact solution, an electronic interface has been designed, preserving as much as possible the excellent performance of the transducer, and turning it into a true standalone positioning sensor. The results obtained using the transducer together with a first prototype of the electronic interface built with cheap discrete elements show that positioning accuracies in the micrometer range are obtainable using this cost-effective solution. Better accuracies would also be attainable but using more involved and costly electronics interfaces.

Low temperature growth of c-axis oriented AlN films on gamma-LiAlO2 by radio frequency magnetron sputtering

Aluminum nitride (AlN) films were prepared on gamma-LiAlO2 substrates by radio frequency (rf) magnetron sputtering. The influence of substrate temperature (T-s) and nitrogen (N-2) concentration on film growth was investigated. The X-ray diffraction (XRD) results reveal that highly c-axis oriented AlN films can be obtained in the temperature range from room temperature (RT) to 300 degrees C. A smoother surface and a crystalline quality decrease with increasing N-2 concentration have been observed by XRD and atomic force microscopy (AFM) for the films deposited at lower substrate temperature. On the contrary, the degradation of the surface smoothness and the higher crystalline quality can be observed for the films deposited at a higher substrate temperature with N-2-rich ambient. The growth mechanism which leads to different crystalline quality of the films is discussed. (C) 2008 Elsevier B.V. All rights reserved.

Use of telemetric tracking to examine environmental influences on catch/effort indices. A case study of Atlantic Salmon (Salmo salar L.)in the R. Tywi, S. Wales

A case study of Atlantic Salmon runs into the R. Tyvi (S. Wales) is presented. Radio tracking of over 200 salmon in 1988 and 1989 has demonstrated that flow is an important factor in modifying both run timing and migratory success. Entry of salmon into the river is typically in response to flow events, and periods of low falling flows delay entry and may directly result in reduced runs into the river. Delayed entry may also increase the proportion of the run migrating after the end of both rod and net fishing seasons. The implications of these results for net and rod catch and catch/effort data are discussed, using both statutory reported catch data and data from specific catch/effort studies. Flow is demonstrated to be a dominant factor in determining the within-season distribution of rod catch and catch/effort during low-flow years. Estuarial seine net catch and catch/effort tend to be controlled more by time of return than by flow although low flows may delay runs. Annual reported rod catch is correlated with flow, which controls in season availability, catchability and consequently the amount of fishing effort. Use of catch or catch/effort data should take account of inter-year variations in flow and other environmental factors. Although catch and catch/effort are valuable indicators of fishery performance, they are inadequate to represent changing stock levels.

Application of Suction-cup-attached VHF Transmitters to the Study of Beluga, Delphinapterus leucas, Surfacing Behavior in Cook Inlet, Alaska

Suction-cup-attached VHF radio transmittes were deployed on belugas, Delphinapterus leucas, in Cook Inlet, Alaska, in 1994 and 1995 to characterize the whales' surfacing behavior. Data from video recordings were also used to characterize behavior of undisturbed whales and whales actively pursued for tagging. Statistics for dive intervals (time between the midpoints of contiguous surfacings) and surfacing intevals (time at the surface per surfacing) were estimated. Operations took place on the tidal delta of the Susitna and Little Susitna Rivers. During the 2-yr study, eight whales were successfully tagged, five tags remained attached for >60 min, and data from these were used in the analyses. Mean dive interval was 24.1 sec (interwhale SD=6.4 sec, n=5). The mean surfacing interval, as determined from the duration of signals received from the radio transmitters, was 1.8 sec (SD=0.3 sec, n=125) for one of the whales. Videotaped behaviors were categorized as "head-lifts" or "slow-rolls." Belugas were more likely to head-lift than to slow-roll during vessel approaches and tagging attempts when compared to undisturbed whales. In undisturbed groups, surfacing intervals determined from video records were significantly different between head-lifting (average = 1.02 sect, SD=0.38 sed, n=28) and slow-rolling whales (average = 2.45 sec, SD=0.37 sec, n=106). Undisturbed juveniles exhibited shorter slow-roll surfacing intervals (average = 2.25 sec, SD=0.32 sec, n=36) than adults (average = 2.55 sec, SD=0.36 sec, n=70). We did not observe strong reactions by the belugas to the suction-cup tags. This tagging method shows promise for obtaining surfacing data for durations of several days.