Energy Functions And Basic Equations For Ferroelectrics

Energy functions (or characteristic functions) and basic equations for ferroelectrics in use today are given by those for ordinary dielectrics in the physical and mechanical communications. Based on these basic equations and energy functions, the finite element computation of the nonlinear behavior of the ferroelectrics has been carried out by several research groups. However, it is difficult to process the finite element computation further after domain switching, and the computation results are remarkably deviating from the experimental results. For the crack problem, the iterative solution of the finite element calculation could not converge and the solutions for fields near the crack tip oscillate. In order to finish the calculation smoothly, the finite element formulation should be modified to neglect the equivalent nodal load produced by spontaneous polarization gradient. Meanwhile, certain energy functions for ferroelectrics in use today are not compatible with the constitutive equations of ferroelectrics and need to be modified. This paper proposes a set of new formulae of the energy functions for ferroelectrics. With regard to the new formulae of the energy functions, the new basic equations for ferroelectrics are derived and can reasonably explain the question in the current finite element analysis for ferroelectrics.

Cloud computing services for seismic networks

This thesis describes a compositional framework for developing situation awareness applications: applications that provide ongoing information about a user's changing environment. The thesis describes how the framework is used to develop a situation awareness application for earthquakes. The applications are implemented as Cloud computing services connected to sensors and actuators. The architecture and design of the Cloud services are described and measurements of performance metrics are provided. The thesis includes results of experiments on earthquake monitoring conducted over a year. The applications developed by the framework are (1) the CSN --- the Community Seismic Network --- which uses relatively low-cost sensors deployed by members of the community, and (2) SAF --- the Situation Awareness Framework --- which integrates data from multiple sources, including the CSN, CISN --- the California Integrated Seismic Network, a network consisting of high-quality seismometers deployed carefully by professionals in the CISN organization and spread across Southern California --- and prototypes of multi-sensor platforms that include carbon monoxide, methane, dust and radiation sensors.

Probabilistic robust control : theory and applications

In this work, the development of a probabilistic approach to robust control is motivated by structural control applications in civil engineering. Often in civil structural applications, a system's performance is specified in terms of its reliability. In addition, the model and input uncertainty for the system may be described most appropriately using probabilistic or "soft" bounds on the model and input sets. The probabilistic robust control methodology contrasts with existing H∞/μ robust control methodologies that do not use probability information for the model and input uncertainty sets, yielding only the guaranteed (i.e., "worst-case") system performance, and no information about the system's probable performance which would be of interest to civil engineers.

The design objective for the probabilistic robust controller is to maximize the reliability of the uncertain structure/controller system for a probabilistically-described uncertain excitation. The robust performance is computed for a set of possible models by weighting the conditional performance probability for a particular model by the probability of that model, then integrating over the set of possible models. This integration is accomplished efficiently using an asymptotic approximation. The probable performance can be optimized numerically over the class of allowable controllers to find the optimal controller. Also, if structural response data becomes available from a controlled structure, its probable performance can easily be updated using Bayes's Theorem to update the probability distribution over the set of possible models. An updated optimal controller can then be produced, if desired, by following the original procedure. Thus, the probabilistic framework integrates system identification and robust control in a natural manner.

The probabilistic robust control methodology is applied to two systems in this thesis. The first is a high-fidelity computer model of a benchmark structural control laboratory experiment. For this application, uncertainty in the input model only is considered. The probabilistic control design minimizes the failure probability of the benchmark system while remaining robust with respect to the input model uncertainty. The performance of an optimal low-order controller compares favorably with higher-order controllers for the same benchmark system which are based on other approaches. The second application is to the Caltech Flexible Structure, which is a light-weight aluminum truss structure actuated by three voice coil actuators. A controller is designed to minimize the failure probability for a nominal model of this system. Furthermore, the method for updating the model-based performance calculation given new response data from the system is illustrated.

Desarrollo de software para la realización de ensayos dinámicos de mecanismos de cinemática paralela

[ES]El presente Trabajo de Fin de Grado tiene como objetivo contribuir al desarrollo de un proyecto de investigación mediante la programación y control del movimiento de mecanismos de cinemática paralela para la realización de ensayos dinámicos. Dicho proyecto está enmarcado dentro de una línea de investigación del grupo de investigación CompMech de la UPV-­‐EHU que gira en torno al desarrollo y estudio de este tipo de mecanismos. Esto es; este trabajo, más allá de la utilidad que pudiera tener por sí mismo, está pensado para formar parte de un proyecto de mayor envergadura, para cuyo éxito será imprescindible la colaboración con otros investigadores y la integración de este trabajo con los realizados por ellos. Consiste en la creación de un software para el control y movimiento de mecanismos, generando vibraciones para la realización de ensayos dinámicos. Para ello, se programarán sobre la plataforma LabVIEW la interfaz de usuario y el motor de cálculo. Una vez se compruebe que el programa funciona correctamente, se integrará dentro de un programa principal, un control articular que será el encargado de comunicarse con la máquina. Posteriormente, se procederá a la realización de ensayos experimentales sobre los propios robots, en taller. Se tomarán medidas mediante acelerómetros y otros dispositivos, determinando las medidas más adecuadas para su correcta validación. Finalmente, se generalizará el trabajo realizado para posibilitar su empleo futuro en diferentes mecanismos

Nuevos phased arrays

[ES]El sistema PAMELA III, con sus correspondientes phased arrays, se diseñó para la detección de daños en aeronaves mediante la tecnología SHM (structural health monitoring). Sin embargo, según los estudios del profesor Tadeusz Stepinski, la distribución de los piezoélectricos utilizada en estos phase arrays producen interferencias. Por ello, este proyecto se basa en el diseño de cuatro phased arrays diferentes, utilizando una de las distribuciones de piezoélectricos estudiada por el profesor Tadeusz. La distribución utilizada es la de cross-shaped (en forma de cruz), con lo que se consigue disminuir las interferencias producidas en los antiguos phased arrays. Además, se ha producido un diseño que es compatible tanto con PAMELA III, como con una futura actualización a PAMELA IV. Con lo que se ha conseguido que se pueda aumentar el tamaño de almacenamiento de la memoria utilizada cambiando la tecnología 1-wire por la de I2C, que sería utilizada solo en el sistema PAMELA IV. Aparte del diseño de los PCBs, también se han diseñado unas piezas de plástico que aportan rigidez a los phased arrays y además, hace que la parte inferior de la tarjeta quede toda a la misma altura y no sobresalgan los piezoélectricos, con lo que aumentará la facilidad de instalación.

Application of sample-and-hold circuits in the laser frequency-shifting

A new method of frequency-shifting for a diode laser is realized. Using a sample-and-hold circuit, the error signal can be held by the circuit during frequency shifting. It can avoid the restraint of locking or even lock-losing caused by the servo circuit when we input a step-up voltage into piezoelectric transition (PZT) to achieve laser frequency-shifting.

Self-healing Techniques for RF and mm-Wave Transmitters and Receivers

With continuing advances in CMOS technology, feature sizes of modern Silicon chip-sets have gone down drastically over the past decade. In addition to desktops and laptop processors, a vast majority of these chips are also being deployed in mobile communication devices like smart-phones and tablets, where multiple radio-frequency integrated circuits (RFICs) must be integrated into one device to cater to a wide variety of applications such as Wi-Fi, Bluetooth, NFC, wireless charging, etc. While a small feature size enables higher integration levels leading to billions of transistors co-existing on a single chip, it also makes these Silicon ICs more susceptible to variations. A part of these variations can be attributed to the manufacturing process itself, particularly due to the stringent dimensional tolerances associated with the lithographic steps in modern processes. Additionally, RF or millimeter-wave communication chip-sets are subject to another type of variation caused by dynamic changes in the operating environment. Another bottleneck in the development of high performance RF/mm-wave Silicon ICs is the lack of accurate analog/high-frequency models in nanometer CMOS processes. This can be primarily attributed to the fact that most cutting edge processes are geared towards digital system implementation and as such there is little model-to-hardware correlation at RF frequencies.

All these issues have significantly degraded yield of high performance mm-wave and RF CMOS systems which often require multiple trial-and-error based Silicon validations, thereby incurring additional production costs. This dissertation proposes a low overhead technique which attempts to counter the detrimental effects of these variations, thereby improving both performance and yield of chips post fabrication in a systematic way. The key idea behind this approach is to dynamically sense the performance of the system, identify when a problem has occurred, and then actuate it back to its desired performance level through an intelligent on-chip optimization algorithm. We term this technique as self-healing drawing inspiration from nature's own way of healing the body against adverse environmental effects. To effectively demonstrate the efficacy of self-healing in CMOS systems, several representative examples are designed, fabricated, and measured against a variety of operating conditions.

We demonstrate a high-power mm-wave segmented power mixer array based transmitter architecture that is capable of generating high-speed and non-constant envelope modulations at higher efficiencies compared to existing conventional designs. We then incorporate several sensors and actuators into the design and demonstrate closed-loop healing against a wide variety of non-ideal operating conditions. We also demonstrate fully-integrated self-healing in the context of another mm-wave power amplifier, where measurements were performed across several chips, showing significant improvements in performance as well as reduced variability in the presence of process variations and load impedance mismatch, as well as catastrophic transistor failure. Finally, on the receiver side, a closed-loop self-healing phase synthesis scheme is demonstrated in conjunction with a wide-band voltage controlled oscillator to generate phase shifter local oscillator (LO) signals for a phased array receiver. The system is shown to heal against non-idealities in the LO signal generation and distribution, significantly reducing phase errors across a wide range of frequencies.

室温下稳定的多波长掺铒光纤激光器的研究

通过在线形谐振腔中引入一段缠绕在压电陶瓷上的单模光纤作为正弦相位调制器，使得激射波长的损耗不固定，抑制由于掺铒光纤的均匀展宽效应引起的模式竞争，从而避免了在室温下不稳定的单波长激射，实现了多波长掺铒光纤激光器的稳定输出。为了获得平坦的多波长输出，在谐振腔里使用了一个损耗峰位于1530nm处的长周期光纤光栅，以获得较为平坦的增益谱。通过两个3dB耦合器制成的反射型梳状滤波器的滤波作用，实验中观察到稳定的多波长激射，相邻波长间隔约为0．45nm。中心9个波长的输出功率平坦度为10dB，边模抑制比大于25dB。

Sensing and Actuation from Biology to Electronics

We introduce an in vitro diagnostic magnetic biosensing platform for immunoassay and nucleic acid detection. The platform has key characteristics for a point-of-use (POU) diagnostic: portability, low-power consumption, low cost, and multiplexing capability. As a demonstration of capabilities, we use this platform for the room temperature, amplification-free detection of a 31 bp DNA oligomer and interferon-gamma (a protein relevant for tuberculosis diagnosis). Reliable assay measurements down to 100 pM for the DNA and 1 pM for the protein are demonstrated. We introduce a novel "magnetic freezing" technique for baseline measurement elimination and to enable spatial multiplexing. We have created a general protocol for adapting integrated circuit (IC) sensors to any of hundreds of commercially available immunoassay kits and custom designed DNA sequences.

We also introduce a method for immunotherapy treatment of malignant gliomas. We utilize leukocytes internalized with immunostimulatory nanoparticle-oligonucleotide conjugates to localize and retain immune cells near the tumor site. As a proof-of-principle, we develop a novel cell imaging and incubation chamber for in vitro magnetic motility experiments. We use the apparatus to demonstrate the controlled movement of magnetically loaded THP-1 leukocytes.

Finally, we introduce an IC transmitter and power ampli er (PA) that utilizes electronic digital infrastructure, sensors, and actuators to self-heal and adapt to process, dynamic, and environmental variation. Traditional IC design has achieved incredible degrees of reliability by ensuring that billions of transistors on a single IC die are all simultaneously functional. Reliability becomes increasingly difficult as the size of a transistor shrinks. Self-healing can mitigate these variations.

Distributed Optimal Control of Cyber-Physical Systems: Controller Synthesis, Architecture Design and System Identification

The centralized paradigm of a single controller and a single plant upon which modern control theory is built is no longer applicable to modern cyber-physical systems of interest, such as the power-grid, software defined networks or automated highways systems, as these are all large-scale and spatially distributed. Both the scale and the distributed nature of these systems has motivated the decentralization of control schemes into local sub-controllers that measure, exchange and act on locally available subsets of the globally available system information. This decentralization of control logic leads to different decision makers acting on asymmetric information sets, introduces the need for coordination between them, and perhaps not surprisingly makes the resulting optimal control problem much harder to solve. In fact, shortly after such questions were posed, it was realized that seemingly simple decentralized optimal control problems are computationally intractable to solve, with the Wistenhausen counterexample being a famous instance of this phenomenon. Spurred on by this perhaps discouraging result, a concerted 40 year effort to identify tractable classes of distributed optimal control problems culminated in the notion of quadratic invariance, which loosely states that if sub-controllers can exchange information with each other at least as quickly as the effect of their control actions propagates through the plant, then the resulting distributed optimal control problem admits a convex formulation.

The identification of quadratic invariance as an appropriate means of "convexifying" distributed optimal control problems led to a renewed enthusiasm in the controller synthesis community, resulting in a rich set of results over the past decade. The contributions of this thesis can be seen as being a part of this broader family of results, with a particular focus on closing the gap between theory and practice by relaxing or removing assumptions made in the traditional distributed optimal control framework. Our contributions are to the foundational theory of distributed optimal control, and fall under three broad categories, namely controller synthesis, architecture design and system identification.

We begin by providing two novel controller synthesis algorithms. The first is a solution to the distributed H-infinity optimal control problem subject to delay constraints, and provides the only known exact characterization of delay-constrained distributed controllers satisfying an H-infinity norm bound. The second is an explicit dynamic programming solution to a two player LQR state-feedback problem with varying delays. Accommodating varying delays represents an important first step in combining distributed optimal control theory with the area of Networked Control Systems that considers lossy channels in the feedback loop. Our next set of results are concerned with controller architecture design. When designing controllers for large-scale systems, the architectural aspects of the controller such as the placement of actuators, sensors, and the communication links between them can no longer be taken as given -- indeed the task of designing this architecture is now as important as the design of the control laws themselves. To address this task, we formulate the Regularization for Design (RFD) framework, which is a unifying computationally tractable approach, based on the model matching framework and atomic norm regularization, for the simultaneous co-design of a structured optimal controller and the architecture needed to implement it. Our final result is a contribution to distributed system identification. Traditional system identification techniques such as subspace identification are not computationally scalable, and destroy rather than leverage any a priori information about the system's interconnection structure. We argue that in the context of system identification, an essential building block of any scalable algorithm is the ability to estimate local dynamics within a large interconnected system. To that end we propose a promising heuristic for identifying the dynamics of a subsystem that is still connected to a large system. We exploit the fact that the transfer function of the local dynamics is low-order, but full-rank, while the transfer function of the global dynamics is high-order, but low-rank, to formulate this separation task as a nuclear norm minimization problem. Finally, we conclude with a brief discussion of future research directions, with a particular emphasis on how to incorporate the results of this thesis, and those of optimal control theory in general, into a broader theory of dynamics, control and optimization in layered architectures.

大行程高分辨率微定位机构的设计分析

压电驱动器的位移输出能力有限，因此通常借助于柔性机构对其位移量进行放大。对常用的柔性放大机构的性能进行了分析。提出一种柔性八杆放大机构，并对其进行有限元分析和理论计算。为了提高放大率，提出两级串连式机构。机构整体具有结构紧凑、放大效率较高的优点。

A Data Dropout Compensation Algorithm Based on the Iterative Learning Control Methodology for Discrete-Time Systems

This paper deals with the convergence of a remote iterative learning control system subject to data dropouts. The system is composed by a set of discrete-time multiple input-multiple output linear models, each one with its corresponding actuator device and its sensor. Each actuator applies the input signals vector to its corresponding model at the sampling instants and the sensor measures the output signals vector. The iterative learning law is processed in a controller located far away of the models so the control signals vector has to be transmitted from the controller to the actuators through transmission channels. Such a law uses the measurements of each model to generate the input vector to be applied to its subsequent model so the measurements of the models have to be transmitted from the sensors to the controller. All transmissions are subject to failures which are described as a binary sequence taking value 1 or 0. A compensation dropout technique is used to replace the lost data in the transmission processes. The convergence to zero of the errors between the output signals vector and a reference one is achieved as the number of models tends to infinity.

Automatización de un proceso de laminación en caliente.

[ES]En la situación actual, en que las empresas han tenido que automatizar los procesos a nivel mundial para hacer frente a los nuevos retos de la competitividad, pone de manifiesto la necesidad de nuevas tecnologías para innovar y redefinir sus procesos. Este proyecto se centra en la aplicación de las nuevas tecnologías en un proceso de laminación en caliente para así a aumentar la capacidad de producción y la calidad de la empresa. Para ello, en primer lugar, se analiza la planta y el proceso a automatizar, se señalan los problemas y se procede a estudiar la solución más adecuada. Después de seleccionar la solución, se colocan sensores y actuadores a lo largo del proceso en función de los pasos a seguir por la fabricación. Con todo ello se ha diseñado una secuencia de control para que el proceso sea autónomo. Además, se diseña un algoritmo para controlar el arranque de los motores, reduciendo así el consumo de energía. En conclusión, se desea mejorar un viejo proceso de producción a través de la automatización y las nuevas tecnologías. Breve descripción del trabajo (cinco líneas). Esta descripción debe destacar los puntos más relevantes del trabajo: su objetivo principal, los métodos a emplear para su desarrollo y los resultados que se pretenden conseguir, o que se han conseguido.

Análisis cinemático de una máquina de cinemática híbrida XY3PRS.

[Es]El objetivo principal de este Trabajo Fin de Grado consiste en calcular los movimientos que son necesarios en los actuadores de la plataforma de un mecanismo de cinemática paralela, a fin de poder localizar la pieza en la posición adecuada para poder llevar a cabo la operación de microfresado de la misma. Para desarrollar el proyecto se necesitará un software de programación como es Matlab. Este trabajo surge de la necesidad de dar soporte a un proyecto mayor que consiste en el diseño de un manipulador de cinemática paralela cuyas juntas funcionan por deformación. Se pretende que mientras la herramienta se encuentra inmóvil, se consiga el microfresado de moldes para la fabricación de microlentes mediante el movimiento del manipulador. Se ha resuelto la cinemática inversa y se ha calculado el espacio de trabajo. En este documento se van a presentar las tareas, el presupuesto y los riesgos del proyecto así como unos anexos en los que se incluirá el código de la programación.