Vehicle energy throughput analysis as a drivetrain motor design aid

There are many variables to consider in the design of an electric motor. However, meeting the performance requirements for an electric vehicle drive may cause a designer to loose focus on its typical operation and hence fail to optimise the motor in the region where it processes the most power. This paper investigates operating requirements of electric vehicle motor drives using the University concept vehicle as an example. The paper outlines a methodology for determining primary operating region of a vehicle drive. The methodology is applied to standard driving cycles that are commonly used in the design and testing of vehicles.

Ironless wheel motor for a direct drive vehicle application

An ironless motor for use as direct wheel drive is presented. The motor is intended for use in a lightweight (600kg), low drag, series hybrid commuter vehicle under development at The University of Queensland. The vehicle will utilise these ironless motors in each of its rear wheels, with each motor producing a peak torque output of 500Nm and a maximum rotational speed of 1500rpm. The axial flux motor consists of twin Ironless litz wire stators with a central magnetic ring and simplified Halbach magnet arrays on either side. A small amount of iron is used to support the outer Halbach arrays and to improve the peak magnetic flux density. Ducted air cooling is used to remove heat from the motor and will allow for a continuous torque rating of 250Nm. Ironless machines have previously been shown to be effective in high speed, high frequency applications (+1000Hz). They are generally regarded as non-optimal for low speed applications as iron cores allow for better magnet utilisation and do not significantly increase the weight of a machine. However, ironless machines can also be seen to be effective in applications where the average torque requirement is much lower than the peak torque requirement such as in some vehicle drive applications. The low spinning losses in ironless machines are shown to result in very high energy throughput efficiency in a wide range of vehicle driving cycles.

Setilement of motor accidents claims with special reference to Kerala

The accident toll on our road traffic is staggering. Obviously this appalling toll of life and.health represents heavy economic loss in addition to human tragedy. the enormous increase in the number of motor vehicles with its rash, negligent and reckless use by unscrupulous, inexperienced and dangerous drivers in the most miserably managed roads coupled with concomitant hazards would draw our attention that Accident Prevention, and Accident compensation are thoroughly two compatiable aims. Proposed solutions to the traffic Problems abound. Preventive efforts concentrated on each of the variables the driver, the road and the vehicle are all being initiated. Still it is a Will the .Motor Vehicles are not considered as dangerous machines. Motoring activity is found useful.A competent and specially trained police force has to be created to deal with the traffic offences in a more scientific ways.The term ‘legal representative needs to be defined on the constructive aspects of relation and dependence.Services of legal aid and public counsels shall necessarily be extended to the poor Motor Accident victims.Timely reporting and timely investigation of Motor Accidents cases will reduce the number of fraudulent claims. There are instances where cases are taken in to investigation after several months of occurrence.It is hoped that the suggestions made above as a result of the present study, if pwgninto practice, may make a humble contribution to the prevention sssof motor accidents and to a faster and speedier settlement of motor accident compensation claims.

Simulació mitjançant tècniques CFD d'una culata per al motor del vehicle de baix consum "Àliga-EPS-UdG"

El projecte pretén estudiar i quantificar les restriccions creades al fluid en circular pels conductes d’admissió i escapament de la culata del motor del vehicle Àliga. L’estudi consta de quatre etapes: estudi de les restriccions actuals dels sistemes d’admissió i escapament; anàlisi dels resultats de la culata de sèrie i proposta de millores aplicables al model real; càlcul de les restriccions creades pels models millorats, i finalment, estudi comparatiu dels resultats obtinguts, interpretant els resultats dels principals paràmetres a analitzar

Determining electric vehicle charging point locations considering drivers' daily activities

In this paper the daily temporal and spatial behavior of electric vehicles (EVs) is modelled using an activity-based (ActBM) microsimulation model for Flanders region (Belgium). Assuming that all EVs are completely charged at the beginning of the day, this mobility model is used to determine the percentage of Flemish vehicles that cannot cover their programmed daily trips and need to be recharged during the day. Assuming a variable electricity price, an optimization algorithm determines when and where EVs can be recharged at minimum cost for their owners. This optimization takes into account the individual mobility constraint for each vehicle, as they can only be charged when the car is stopped and the owner is performing an activity. From this information, the aggregated electric demand for Flanders is obtained, identifying the most overloaded areas at the critical hours. Finally it is also analyzed what activities EV owners are underway during their recharging period. From this analysis, different actions for public charging point deployment in different areas and for different activities are proposed.

Research on vehicle-based driver status/performance monitoring; development, validation, and refinement of algorithms for detection of driver drowsiness.

National Highway Traffic Safety Administration, Washington, D.C.

Recent international activity in cooperative vehicle-highway automation systems /

This report summarizes the current state of the art in cooperative vehicle-highway automation systems in Europe and Asia based on a series of meetings, demonstrations, and site visits, combined with the results of literature review. This review covers systems that provide drivers with a range of automation capabilities, from driver assistance to fully automated driving, with an emphasis on cooperative systems that involve active exchanges of information between the vehicles and the roadside and among separate vehicles. The trends in development and deployment of these systems are examined by country, and the similarities and differences relative to the U.S. situation are noted, leading toward recommendations for future U.S. action. The Literature Review on Recent International Activity in Cooperative Vehicle-Highway Automation Systems is published separately as FHWA-HRT-13-025.

Assessment of impoundment and forfeiture laws for drivers convicted of DUI. Phase II report: evaluation of Oregon and Washington Vehicle Plate Zebra Sticker Laws. Final report.

National Highway Traffic Safety Administration, Washington, D.C.

A nationwide survey of truck and bus drivers. Final report.

Federal Highway Administration, Bureau of Motor Carrier Safety, Washington, D.C.

Packard Motor Co. test touring car and three drivers

Photo album title: Three Men in a Six. President H. B. Joy; Chief Engineer Russell Huff; General Superintendent B. F. Roberts

The motor truck; applied mechanics for owners and drivers,

Mode of access: Internet.

Winding-centre-tapped switched reluctance motor drive for multi-source charging in electric vehicle applications

Switched reluctance motors (SRMs) can provide an attractive traction drive for electric vehicle applications. To lower the investment in the off-board charging station facilities, a multi-functional switched reluctance motor topology is proposed on the basis of the traditional asymmetrical half-bridge converter. The SRM phase windings are employed as input filter inductors and centre-tapped windings are also developed to form symmetrical inductors for three-phase grid supply. Owing to the varying rotor position, phase inductors are unequal between one another. A hysteresis control scheme is therefore developed for grid-connection operation. In addition to AC supplies, the proposed topology can also supports the DC-source charging. A new current sharing strategy is employed to diminish the influence of the unequal winding inductances. The simulation and experimental tests are carried out to verify the proposed topology and control methods. Since this work eliminates the need for building charging station infrastructure, its potential economic impact on the automotive market can be significant.