Parallel Fully-Implicit Computation of Magnetohydrodynamics Acceleration Experiments

A three-dimensional MHD solver is described in the paper. The solver simulates reacting flows with nonequilibrium between translational-rotational, vibrational and electron translational modes. The conservation equations are discretized with implicit time marching and the second-order modified Steger-Warming scheme, and the resulted linear system is solved iteratively with Newton-Krylov-Schwarz method that is implemented by PETS,: package. The results of convergence tests arc plotted, which show good scalability and convergence around twice faster when compared with the DPLR method. Then five test runs are conducted simulating the experiments done at the NASA Ames MHD channel, and the calculated pressures, temperatures, electrical conductivity, back EMF, load factors and flow accelerations are shown to agree with the experimental data. Our computation shows that the electrical conductivity distribution is not uniform in the powered section of the MHD channel, and that it is important to include Joule heating in order to calculate the correct conductivity and the MHD acceleration.

Investigations of phase inversion and frictional pressure gradients in upward and downward oil–water flow in vertical pipes

The present study has attempted to investigate phase inversion and frictional pressure gradients during simultaneous vertical flow of oil and water two-phase through upward and downward pipes. The liquids selected were white oil (44 mPa s viscosity and 860 kg/m3 density) and water. The measurements were made for phase velocities varying from 0 to 1.24 m/s for water and from 0 to 1.87 m/s for oil, respectively. Experiments were carried either by keeping the mixture velocity constant and increasing the dispersed phase fraction or by keeping the continuous phase superficial velocity constant and increasing the dispersed phase superficial velocity. From the experimental results, it is shown that the frictional pressure gradient reaches to its lower value at the phase inversion point in this work. The points of phase inversion are always close to an input oil fraction of 0.8 for upward flow and of 0.75 for downward flow, respectively. A few models published in the literature are used to predict the phase inversion point and to compare the results with available experimental data. Suitable methods are suggested to predict the critical oil holdup at phase inversion based on the different viscosity ratio ranges. Furthermore, the frictional pressure gradient is analyzed with several suitable theoretical models according to the existing flow patterns. The analysis reveals that both the theoretical curves and the experimental data exhibit the same trend and the overall agreement of predicted values with experimental data is good, especially for a high oil fraction.

固定化红酵母细胞合成L-苯丙氨酸研究

In this paper, bioconversion of trans-cinnamic acid(t-Ca)to L-phenylalanine (L-phe) has been investigated by using immobilized yeast cells with induced L-phe Ammonia-lyase(PAL, EC.4.3.1.5) as biocatalysts. The contents are the following. (1) Thirty strains of yeasts, including two genera (Rhodotorula, Sporobolomyces), six species (R. glutinis R. minuta,R.rubra,R.sineses,R.roseus and S.salmonicolor)were screened for their ability to converse the substrates, t-Ca and ammonia, to the product, L-phe, by using yeast cells as biocatalyst, and primary evaluation for PAL activity of the selected strains was investigated. From the results of the screening experiments, it was found that 22 strains were able to produce L-phe from t-Ca with the range of conversion yield from 2% to 67%. Studies on PAL formation time course during cultivation show that the maximum PAL activity of several different strains ranges from 2.3 to 14.4×10-3U/mg cell dry weight. The biomass of tested strains at their maximum enzyme activity is also greatly varied. (2)One of the selected strains, R. rubra as 2.166, was used for immobilized cells as biocatalysts to produce L-phe. The optimum conversion conditions and effective stablization agents were investigated. The results shown that polyacrylamide gel was chosen as a suitable matrix for immobilization of the yeast cells, and it can retain 88% of the PAL activity in the reverse direction at the following reactive conditions: [t-Ca]: 34mM. [NH4OH]: 6.OM.PH10.00, temperature: 30℃. (3) The effects of various kinds of effectors on the production of L-phe were also examined. Membrane permeabilizing agents can stimulate L-phe synthesis, but make the stability of PAL decline greatly. Polyalchoholic agents and glutamic acid were very effective for the stabilization of PAL. At the presence of glutamic acid (5%), the half life of L-phe productivity with the immobilized cells was extended to 192 hours, which was much higher than most of that having been reproted, while the half life of resting cells was only about 15 hours. (4) Use of initial velocity studies on the kinetics of enzyme-catalized reaction indicated that the apparent Km value was 13.0mM for the immobilized cells, and 4.8mM for the resting cells. Thermostability of the immobilized cells was better than the resting cells. Fluid bed bioreactor is more effective than batch bioreator in prolonging the thermostability of the biocatalysts. (5) CGA- 688 resin column chromatographic procedure was employed in the isolation and purification of L-phe, t-Ca and other substances from the reactire mixture. (6) Preparative-scale production of L-phe on a level of gram amount by immobilized cells from the culture broth of R. rubra AS2.166 allowed for the conversion yield with 30%. The characteristic physico-chemical criteria (including melting point, optical activity, elements analysis, IR, NMR) are the same with the standard L-phe. 本文报告了利用诱导的苯丙氨酸解氨酶 (PAL.EC.4.3.1.5)催化反式肉桂酸(t-Ca)氨加 成制备L-苯丙氨酸(L-phe)的研究，主要内容为：(1) 我们搜集了三十株酵母菌株，利用全细胞转化t-Ca生成L-phe的能力进行了直 接筛选，并对其PAL活性水平进行了初步评估研究。研究结果表明，其中22株酵母具有转化t-Ca生产L-phe的能力，它们包括 Rhodotorula glutinis,R.rubra, R.sineses 和Sporobolomyces roseus 的菌株，转化率在2-67%。细胞生长和PAL形成过程的研究 表明，不同菌株PAL最大活力在2.3-14.4×10-3U/mg 细胞干重，达到最大PAL活性时各株酵母的生长情况也极不一致。(2) 利用筛 选出的一株深红酵母R.rubra AS2.166 作为供试菌株，研究了细胞固定化条件下生物转化的最适条件及PAL在固定化条件下的稳定 性。结果表明以聚丙烯酰胺凝胶包埋法较为理想，能使细胞合成L-phe活力保持88%，最适t-Ca浓度为34mM，最适NH4OH浓度为6M,最 适PH10.0，最适温度45℃。(3) 多种效应物对L-phe 合成的影响研究表明：表面活性剂能刺激L-phe的合成，但使PAL稳定性下降。 多羟基化合物及Glu对PAL的稳定十分有效在有Glu存在下，能使固定化细胞合成L-phe的半寿期达192小时左右，高于大部分现已报 导的固定化结果。(4) 用初速度法研究了深红酵母AS2.166中PAL的酶促反应特征，测得固定化细胞对t-Ca的表观米氏常数Km为 13.0mM，全细胞为4.8mM，细胞固定后热稳定性提高。(5) 建立了适合低浓度分离纯化产物与底物的聚苯乙烯大孔树脂柱层析技术 ，能使L-phe与t-Ca及产物混合物中其它成分有效分开。(6) 利用固定化的R.rubra AS2.166细胞所做的制备实验能够使L-phe的产 率达到30%左右，其主要的理化指标(包括熔点、比旋光度、元素分析、IR、NMR等)与标准L-phe一致。

真菌单宁酶发酵五倍子和有机溶剂中酶法合成没食子酸丙酯的研究

本文报告了丝状真菌单宁酶发酵五倍子及有机溶剂中酶法合成没食子酸丙酯的研究。利用单宁和/或五倍子诱导丝状真菌产生单宁 酶的原理，借助二级发酵程序，对从天然源得到的75株菌进行了生物转化实验研究。选择出既能水解单宁或五倍子成没食子酸，又 能把没食子酸和丙醇合成没食子酸丙酯，而且生物催化活性都较高的1株菌，这株菌经初步鉴定为黑曲霉(Aspergillus niger No.17)。随后对它开展了产酶条件和参数优化实验，得出了最佳培养条件。立足于参数优化实验方案的基础上，经由液体培养发酵 制备单宁酶制剂，并把该酶通过化学手段共价结合到一种新型载体—聚乙烯醇和戊二醛反应生成的缩醛上，制备得到固定化单宁酶 。这种固定化生物催化剂在两种有机介质体系中都具有逆向催化合成没食子酸丙酯的能力。最后建立起来一条有效可行的微生物酶 法制备没食子酸的技术途径，没食子酸产率达到70%。对这种物质进行元素 分析：含C,49.45%;含H,3.63%。它的熔点为237℃～243 ℃，三种溶剂系统的TLC均只给出一个斑点。这些数据都与标准品一致。有机溶剂中酶法合成没食子酸丙酯的技术途径已经建立。 水溶性单宁酶在潜溶剂体系中也能催化上述酯化反应，反应混合物中的PG浓度为16.4mmol/L，制备薄层被用于分离反应混合物所含 的PG，这种产物被红外、质谱及三种溶剂系统的TLC等方法鉴定，确证为目标产物。在这一学位论文的实验研究过程中，还包括一 些生化分析方法的建立和应用，这些方法用于鉴定底物和产物及测定它们的浓度，其内容主要包括TLC定性/半定量分析、元素分析 、质谱、红外等手段的综合运用。本工作为开发我国特有的天然产物资源—五倍子的生物化工加工技术及非水相生物催化技术的开 发，提供了有用的基础数据资料，具有应用基础研究工作的重要性。In this thesis, the studies on the fermentation of Chinese gallotannin by filamentous fungi with tannase activity and enzymatic synthesis of propyl gallate(PG) in organic solvents were described through these biocatalysts. Based on the principles of induction enzyme, the tannase produced from filamentous fungi by adding tannic acid(TA) and/or Chinese gallotannin into media was investigated, and the screening experiments of bioconversion were done with 75 strains by means of a two-stage fermentation procedure. These strains were isolated with the enrichment culture technique from natural sources. Hence we selected one strain (Aspergillus niger No.17) that can not only catalyze the hydrolyses of TA and/or Chinese gallotannin into gallic acid(GA) in the liquid cultures, but also be used to synthesize PG from propanol and GA in the non-aqueous media. At the same time both of its biocatalytical activities were higher. This strain was calssified to be Aspergillus niger by the primary identification. Then optimum conditions for production of the tannase and its parameters were examined. In this way, one set of optimum culture conditions was selected. Making use of the optimum proposal, the tanase was prepared through a liquid fermentation procedure. The enzyme was convalently coupled to a new type of carrier which was made chemically from polyvinyl alcohol(PVA)and glutaraldehyde. The immobilized enzymes were able to synthesize PG reversely in two organic media. Finally, an effective enzymatic technique for production of GA was developed. The yield of GA products was up to 70%。Element analysis for this substance: calce: C, 49.42%; H, 3.56%; found: C, 49.45%, H, 3.63%. Its melting point was 237℃～ 243℃ and TLCs on three solvent systems gave only one spot respectively. These data were identical with theauthentic GA. The enzymatic synthesis of PG in organic solvents was extablished with reverse route of tannase catalytical hydrolysis. Aqueous enzyme perparation also catalyzed above esterification in a buffer system. The PG concentration in the reaction mixture was 16.4mmol/L. The reparative-scale TLC was used to isolate PG from the reaction mixture. This product separated was identified by IR, MS and TLC on three solvent systems. In this study of thesis, some biochemical analytical mehtods were developed and used to identify substrates and products, and to determinate their concentration. These methods, including TLC qualitative/half quantitative analysis, element analysis, MS, IR and so on, were useful, available and performable. This work provided basic data and information for developing the biochemical engineering and bio-processing of Chinese gallotannin-a special natural resource in China and the non-aqueous phase biocatalysis. Thus, this study possesses importance in the applied and basic research work.

Experiments and modification on electron cyclotron resonance ion sources at the Institute of Modern Physics

Uranium ion beams were produced from electron cyclotron resonance (ECR) ion sources by sputtering method this year at the Institute of Modern Physics. At first, we chose the Lanzhou ECR No. 3 ion source to implement the production experiment of U ion beams. Finally, 11 e mu A of U28+, 5 e mu A of U32+, and 1.5 e mu A of U35+ were obtained. A U26+ ion beam produced by the LECR2 ion source was accelerated successfully by the cyclotron. This means that the Heavy Ion Research Facility in Lanzhou (HIRFL) has accomplished the acceleration of the ion beam of the heaviest element according to the designed parameters. The Lanzhou ECR ion source No. 2 (LECR2), which was built in 1997, has served the HIRFL for eight years and needed to be upgraded to provide more intense high charge state ion beams for HIRFL cooling storage ring. We started the upgrading project of LECR2 last year, and the modified design just has been finished. (c) 2006 American Institute of Physics.

Test experiments of gamma-ray linear polarization using a Clover detector

We have investigated the performance of a EXOGAM-Segmented-Clover with 16 segments as a Compton polarimeter to measure the linear polarization of gamma rays. The polarization sensitivity of the Clover detector has been measured at the energy of 1332keV through the coincidence measurements of cascade gamma-rays from Co-60. Experimental values were in good accord with our expectation.We have investigated the performance of a EXOGAM-Segmented-Clover with 16 segments as a Compton polarimeter to measure the linear polarization of gamma rays. The polarization sensitivity of the Clover detector has been measured at the energy of 1332keV through the coincidence measurements of cascade gamma-rays from Co-60. Experimental values were in good accord with our expectation.

Kinetic modeling of growth and biodegradation of phenol and m-cresol using Alcaligenes faecalis

A phenol-degrading. microorganism, Alcaligenes faecalis, was used to study the substrate interactions during cell growth on phenol and m-cresol dual substrates. Both phenol and m-cresol could be utilized by the bacteria as,the sole carbon and energy sources. When cells grew on the mixture of phenol and m-cresol, strong substrate interactions were observed. m-Cresol inhibited the degradation of phenol, on the other hand, phenol also inhibited the utilization of m-cresol, the overall cell growth rate was the co-action of phenol and m-cresol. In addition, the cell growth and substrate degradation kinetics of phenol, m-cresol as single and mixed substrates for A. faecalis in batch cultures were also investigated over a wide range of initial phenol concentrations (10-1400 mg L-1) and initial m-cresol concentrations (5-200 mg L-1). The single-substrate kinetics was described well using the Haldane-type kinetic models, with model constants of it mu(m1) = 0.15 h(-1), K-S1 = 2.22 mg L-1 and K-i1 = 245.37 mg L-1 for cell growth on phenol and mu(m2) = 0.0782 h(-1), K-S2 = 1.30 mg L-1 and K-i2 = 71.77 mgL(-1), K-i2' = 5480 (mg L-1)(2) for cell growth on m-cresol. Proposed cell growth kinetic model was used to characterize the substrates interactions in the dual substrates system, the obtained parameters representing interactions between phenol and m-cresol were, K = 1.8 x 10(-6), M = 5.5 x 10(-5), Q = 6.7 x 10(-4). The results received in the experiments demonstrated that these models adequately described the dynamic behaviors of phenol and m-cresol as single and mixed substrates by the strain of A. faecalis.

Conformal irradiation to moving targets in heavy ion radiotherapy with raster-scanning beam delivery system: (II) feasibility experiments

Within the framework of the pilot heavy-ion therapy facility at GSI equipped with an active beam delivery system of advanced raster scanning technique, a feasibility study on actively conformal heavy-ion irradiation to moving tumors has been experimentally conducted. Laterally, real-time corrections to the beam scanning parameters by the raster scanner, leading to an active beam tracing, compensate for the lateral motion of a target volume. Longitudinally, a mechanically driven wedge energy degrader (called depth scanner) is applied to adjust the beam energy so as to locate the high-dose Bragg peak of heavy ion beam to the slice under treatment for the moving target volume. It has been experimentally shown that compensations for lateral target motion by the raster scanner and longitudinal target shift by the depth scanner are feasible.