A non-linear analogue-to-digital converter for linearization of transducer input-output relationships

Analogue and digital techniques for linearization of non-linear input-output relationship of transducers are briefly reviewed. The condition required for linearizing a non-linear function y = f(x) using a non-linear analogue-to-digital converter, is explained. A simple technique to construct a non-linear digital-to-analogue converter, based on ' segments of equal digital interval ' is described. The technique was used to build an N-DAC which can be employed in a successive approximation or counter-ramp type ADC to linearize the non-linear transfer function of a thermistor-resistor combination. The possibility of achieving an order of magnitude higher accuracy in the measurement of temperature is shown.

Impacts of sodic soil amelioration on deep drainage

Groundwater tables are rising beneath irrigated fields in some areas of the Lower Burdekin in North Queensland, Australia. The soils where this occurs are predominantly sodic clay soils with low hydraulic conductivities. Many of these soils have been treated by applying gypsum or by increasing the salinity of irrigation water by mixing saline groundwater with fresh river water. While the purpose of these treatments is to increase infiltration into the surface soils and improve productivity of the root zone, it is thought that the treatments may have altered the soil hydraulic properties well below the root zone leading to increased groundwater recharge and rising water tables. In this paper we discuss the use of column experiments and HYDRUS modelling, with major ion reaction and transport and soil water chemistry-dependent hydraulic conductivity, to assess the likely depth, magnitude and timing of the impacts of surface soil amelioration on soil hydraulic properties below the root zone and hence groundwater recharge. In the experiments, columns of sodic clays from the Lower Burdekin were leached for extended periods of time with either gypsum solutions or mixed cation salt solutions and change s in hydraulic conductivity were measured. Leaching with a gypsum solution for an extended time period, until the flow rate stabilised, resulted in an approximately twenty fold increase in the hydraulic conductivity when compared with a low salinity, mixed cation solution. HYDRUS modelling was used to high light the role of those factors which might influence the impacts of soil treatment, particularly at depth, including the large amounts of rain during the relatively short wet season and the presence of thick low permeability clay layers.

Enhanced ionic conduction in dispersed solid electrolyte systems CaF2---Al2O3 and CaF2---CeO2

Dispersions of Al2O3 as well as CeO2 in CaF2 are found to enhance the conductivity of CaF2. Both these systems are biphasic and the electrical conduction in them is purely ionic in nature. At 650 K the increase in the ionic conductivity of the dispersed solid electrolyte system CaF2---Al2O3 is by about two orders of magnitude in relation to the conductivity of the host electrolyte CaF2, whereas for the CaF2---CeO2 system it is about three orders of magnitude. Some aspects of the increase in the ionic conductivities of CaF2---Al2O3 and CaF2---CeO2 electrolytes can be explained by a recent theoretical model. It is proposed that a substantial enhancement in the vacancy concentration of CaF2, brought about by the attraction of F− ions to the surface of Al2O3 (or CeO2), is responsible for the low temperature increase in the ionic conductivity of CaF2.

Development and validation of an ELISA for detecting antibodies to Eimeria tenella in chickens

The aim of this study was to develop and validate an ELISA for detecting chicken antibodies to Eimeria tenella. An initial comparison of merozoite and sporozoite antigen preparations revealed few differences in their ability to monitor the onset, kinetics and magnitude of the antibody response suggesting that both antigens would be equally useful for development of an ELISA. Furthermore the cross-reactivity of these antigens with sera from birds infected with chicken Eimeria species was similar. The merozoite antigen was selected for further evaluation because it was easier to prepare. Discrimination between sera from birds experimentally infected with E. tenella and birds maintained in an Eimeria-free isolation facility was excellent. In sera collected from free-range layers and commercial broilers there also appeared to be clear discrimination between infected and uninfected birds. The ELISA should prove useful for monitoring infectivity in vaccination programmes in layer and breeder flocks and for assessing the effectiveness of biosecurity measures in broiler flocks.

Laminar flow of a suspension in a curved pipe with varying curvature

The laminar flow of a fairly concentrated suspension (in which the volume fraction Z of the solid particles < 0.4) in a spatially varying periodically curved pipe has been examined numerically. Unlike the case of interacting suspension flows, the particles are found to flow in a well-mixed fashion, altering both the axial and circumferential velocities and consequently the fluid flux in the tube, depending on their diffusivity and inertia. The magnitude of shear stress at the wall is enhanced, suggesting that, if applied to vascular system, the vascular wall could be prone to ulceration during pathological situations like polycythemia. The delay in adaptation of the deviation in Poiseuille flow velocity to the curvature changes is also discussed in detail.

Construction, installation, and performance of two repacked weighing lysimeters

Weighing lysimeters are the standard method for directly measuring evapotranspiration (ET). This paper discusses the construction, installation, and performance of two (1.52 m × 1.52 m × 2.13-m deep) repacked weighing lysimeters for measuring ET of corn and soybean in West Central Nebraska. The cost of constructing and installing each lysimeter was approximately US $12,500, which could vary depending on the availability and cost of equipment and labor. The resolution of the lysimeters was 0.0001 mV V-1, which was limited by the data processing and storage resolution of the datalogger. This resolution was equivalent to 0.064 and 0.078 mm of ET for the north and south lysimeters, respectively. Since the percent measurement error decreases with the magnitude of the ET measured, this resolution is adequate for measuring ET for daily and longer periods, but not for shorter time steps. This resolution would result in measurement errors of less than 5% for measuring ET values of ≥3 mm, but the percent error rapidly increases for lower ET values. The resolution of the lysimeters could potentially be improved by choosing a datalogger that could process and store data with a higher resolution than the one used in this study.

Technology and the City: Systems, Applications and Implications

This book investigates and reveals the interplay between smart technologies and cities, a topic that has gained incredible currency in urban studies in recent years. Beginning with an elaboration of the historical significance of technologies in economic growth, social progress and urban development, the author then goes on to introduce the most prominent smart urban information technologies before demonstrating the use of these technologies in various smart urban systems. The book then showcases some of the most significant cases of smart city best practice from across the globe before discussing the magnitude and prospects of smart technologies and systems for our cities and societies. "The interplay between smart urban technologies and city development is a relatively uncharted territory. Technology and the City aims to fill that gap, exploring the growing importance of smart technologies and systems in contemporary cities, and providing an in-depth understanding of both theoretical and practical aspects of smart urban technology adoption, and its implications for our cities. Beginning with an elaboration of the historical significance of technologies in economic growth, social progress and urban development, Yigitcanlar introduces the most prominent smart urban information technologies. The book showcases significant smart city practices from across the globe that uses smart urban technologies and systems most effectively. It explores the role of these technologies and asks how they can be adopted into the planning, development and management processes of cities for sustainable urban futures. This pioneering volume contributes to the conceptualisation and practice of smart technology and system adoption in our cities by disseminating both conceptual and empirical research findings with real-world best practice applications. With a multidisciplinary approach to themes of technology and urban development, this book is a key reference source for scholars, practitioners, consultants, city officials, policymakers and urban technology enthusiasts."--Publisher website

Process studies of odour emissions from effluent ponds using machine-based odour measurement

Replicable experimental studies using a novel experimental facility and a machine-based odour quantification technique were conducted to demonstrate the relationship between odour emission rates and pond loading rates. The odour quantification technique consisted of an electronic nose, AromaScan A32S, and an artificial neural network. Odour concentrations determined by olfactometry were used along with the AromaScan responses to train the artificial neural network. The trained network was able to predict the odour emission rates for the test data with a correlation coefficient of 0.98. Time averaged odour emission rates predicted by the machine-based odour quantification technique, were strongly correlated with volatile solids loading rate, demonstrating the increased magnitude of emissions from a heavily loaded effluent pond. However, it was not possible to obtain the same relationship between volatile solids loading rates and odour emission rates from the individual data. It is concluded that taking a limited number of odour samples over a short period is unlikely to provide a representative rate of odour emissions from an effluent pond. A continuous odour monitoring instrument will be required for that more demanding task.

Repeatable Condition-Invariant Visual Odometry for Sequence-Based Place Recognition

This paper describes a vision-only system for place recognition in environments that are tra- versed at different times of day, when chang- ing conditions drastically affect visual appear- ance, and at different speeds, where places aren’t visited at a consistent linear rate. The ma- jor contribution is the removal of wheel-based odometry from the previously presented algo- rithm (SMART), allowing the technique to op- erate on any camera-based device; in our case a mobile phone. While we show that the di- rect application of visual odometry to our night- time datasets does not achieve a level of perfor- mance typically needed, the VO requirements of SMART are orthogonal to typical usage: firstly only the magnitude of the velocity is required, and secondly the calculated velocity signal only needs to be repeatable in any one part of the environment over day and night cycles, but not necessarily globally consistent. Our results show that the smoothing effect of motion constraints is highly beneficial for achieving a locally consis- tent, lighting-independent velocity estimate. We also show that the advantage of our patch-based technique used previously for frame recogni- tion, surprisingly, does not transfer to VO, where SIFT demonstrates equally good performance. Nevertheless, we present the SMART system us- ing only vision, which performs sequence-base place recognition in extreme low-light condi- tions where standard 6-DOF VO fails and that improves place recognition performance over odometry-less benchmarks, approaching that of wheel odometry.

Dietary composition manipulation to enhance the performance of juvenile barramundi (Lates calcarifer Bloch) reared in cool water

Barramundi Lates calcarifer reared in cool water (20-22 degrees C) grow slowly and feed is used poorly compared with fish in warm water (28-32 degrees C). Two comparative slaughter growth assays were carried out with juvenile barramundi to see if increasing the digestible energy (DE) and/or the n-3 highly unsaturated fatty acid (n-3 HUFA) content of the feed would improve growth of fish raised in cool water. Increasing the DE content of the feed from 15 to 17 or 19 MJ kg(-1) while maintaining a constant protein to energy ratio in Experiment 1 brought about significant improvements in feed conversion ratio (FCR) (from 2.01 to 1.19) and daily growth coefficient (DGC; from 0.69 to 1.08%/day) for fish at 20 degrees C. For fish at 29 degrees C, improvements, while significant, were of a lesser magnitude: from 1.32 to 0.97 for FCR and from 3.24 to 3.65%/day for DGC. Increasing the absolute amount of dietary n-3 HUFA, expressed as the sum of eicosapentaenoic and docosahexaenoic fatty acids, from 0.5% to 2.0% in Experiment 2 improved DGC linearly and FCR curvilinearly for fish at 29 degrees C whereas at 20 degrees C, DGC was not affected while FCR improved slightly (from 1.83 to 1.68). Feed conversion ratio was optimized with a dietary n-3 HUFA of about 1.5%. Providing barramundi with a feed that is high in DE (viz 19 MJ kg(-1)) and a digestible protein to DE ratio of 22.5 g MJ(-1) is a practical strategy for improving the productivity of barramundi cultured in cool water whereas increasing dietary n-3 HUFA conferred very little additional benefit.

Alkaloid production by isolates of the sorghum ergot pathogen (Claviceps africana) from Australia and other countries

Isolates of Claviceps africana from Australia, Africa, Asia, and America were tested for the production of dihydroergosine (DHES), and its biogenic precursors dihydroelymoclavine (DHEL) and festuclavine (FEST), in culture. Several growth media were evaluated to optimise alkaloid production with little success. The best of these involved 2-stage culturing on high-sucrose substrate. Australian C. africana isolates varied widely and inconsistently in alkaloid production, with DHES concentrations in mycelium ranging from: <0.1 to 9 mg DHES/kg; <0.1 to 1.6 mg DHEL/kg; and <0.1 to 0.4 mg FEST/kg. In a separate experiment using similar culturing techniques, DHES was produced by 2 of 3 Australian isolates, 1 of 3 USA isolates, 1 of 4 Indian isolates, the sole Puerto Rican isolate, the sole Japanese isolate, but not the sole South African isolate. In this experiment, DHES concentrations detected in mycelium of Australian isolates (0.1-1.0 mg DHES/kg) were of similar magnitude to isolates from other countries (0.2-1.8 mg DHES/kg). Three C. africana isolates, including one that produced only traces of alkaloid in culture after 8 weeks, were inoculated onto panicles of sterile male sorghum plants. After 8 weeks, all 3 isolates produced 10-19 mg DHES/kg in the panicles, demonstrating that the growing plant favoured more consistent alkaloid production than culture medium.

Phase relations between Al2O3---Cr2O3 and FeAl2O4---FeCr2O4 solid solutions at 1823 K

Tie-lines between the corundum and spinel solid solutions have been determined experimentally at 1823 K. Next, activities of FeCr2O4 and FeAl2O4 in the spinel solid solution were determined by combining the tie-line data with literature values for the activities of Cr2O3 and Al2O3 in the corundum phase. Activities and the Gibbs energy of mixing for the spinel solid solution were also obtained from a model based on cation distribution between nonequivalent crystallographic sites in the oxide lattice. The difference between the Gibbs energy of mixing obtained experimentally and from the model has been attributed to a strain enthalpy term which is relatively unchanged in magnitude from the reported at 1373 K. The integral enthalpy of mixing obtained from experimental data at 1373 and 1823 K using the second law is compared with the model result.

A New PWM Control Method for Three-Phase Autosequentially Commutated Current Source Inverters

A new current pulsewidth modulation (PWM) method is presented which uses the principle of creating zero three-phase currents at selected instants of time, through which the load current harmonic content can be controlled along with the magnitude of its fundamental content. This gives rise to reduction of motor torque ripples through the selection of suitable PWM patterns and a fast current control in the inverter by varying the pulsewidths of the PWM pattern. Under this new PWM mode of operation, the autosequentially commutated inverter (ASCI) circuit can be modified easily so that a higher number of pulses can be accomodated within a half-cycle, compared to the normal ASCI circuit. The experimental oscillograms verify the effectiveness of the new PWM method.

The effects of +Gz force on the bone mineral density of fighter pilots

HYPOTHESIS Bone is a metabolically active tissue which responds to high strain loading. The purpose of this study was to examine the bone response to high +Gz force loading generated during high performance flying. METHODS The bone response to +Gz force loading was monitored in 10 high performance RAAF pilots and 10 gender-, age-, height-, weight-matched control subjects. The pilots were stationed at the RAAF base at Pearce, Western Australia, all completing the 1-yr flight training course. The pilots flew the Pilatus PC-9 aircraft, routinely sustaining between 2.0 and 6.0 +Gz. Bone mineral density (BMD) and bone mineral content (BMC) were measured at baseline and 12 mo, using the Hologic QDR 2000+ bone densitometer. RESULTS After controlling for change in total body weight and fat mass, the pilots experienced a significant increase in BMD and BMC for thoracic spine, pelvis, and total body, in the magnitude of 11.0%, 4.9%, and 3.7%, respectively. However, no significant changes in bone mineral were observed in the pilots lumbar spine, arms or legs. The control group experienced a significant decrease in pelvic BMC, with no other bone mineral changes observed at any site. CONCLUSIONS These findings suggest that site specific BMD is increased in response to high +Gz forces generated during high performance flying in a PC-9.

Kinetics of Extraction of Iron(II1) by Bis(2-ethylhexyl Phosphate in a Laminar Liquid-Liquid Jet Reactor

The kinetics of iron(II1) extraction by bis(Zethylhexy1) phosphate (HDEHP, HA) in kerosene from sulfuric acid solutions has been studied in a liquid-liquid laminar jet reactor. The contact time of the interface in this reacting device is of the same order of magnitude as the surface renewal time in dispersion mixing and much less than that obtained in the relatively quiescent condition of the Lewis cell. Yet the analysis of the data in this study suggested a rate-controlling step involving surface saturation quite in conformity with that obtained in the Lewis cell and not with that in dispersion mixing as reported in the literature. Further, the mechanism suggested a weaker dependence of the rate on hydrogen ion concentration which was reported by other workers.