Second generation European corn borer injury and Irish potato physiology, yield, and quality

European corn borer (ECB) [Ostrinia nubilalis (Hubner)] (Lepidoptera: Crambidae) is known to infest Irish potato (Solanum tuberosum L.) but only causes economic damage during the first generation in East Coast potato producing areas. However, in Nebraska, second generation ECB infest potato plants during the bulking period and may reduce yield and/or potato quality. Experiments were conducted in 2001, 2002, and 2003 to examine physiological and yield effects of second generation ECB injury to potato in Nebraska. Pike, Atlantic, and three Frito Lay proprietary varieties (FL1867, FL1879, and FL1833) were used. Experimental plots were infested with four ECB egg masses per plant to simulate ECB infestation by second-generation larvae; controls received no egg masses. Photosynthetic rates, tuber weights, tuber size grades, solids, and fry quality were measured. Potato plants with ECB infestation had significantly reduced photosynthetic rates on ECB-infested stems and on uninfested stems on the same plant when larvae were in the fifth instar. When insects were in the fourth instar, photosynthetic rates were reduced only on ECB-infested stems. In 2001, ECB infestation reduced the average mass of large tubers and increased the amount of small tubers in FL1867 and FL1879. In 2002, significant yield reductions were not observed. Across both years, ECB-infested plots produced fewer large (65- to 100-mm diam.) tubers than control plots. Other tuber properties and chip qualities were unaffected. This study indicates that second generation ECB infestation of approximately 30% infested plants results in economic loss for some chipping varieties and affects tuber bulking. In contrast to east coast growers, Midwest potato farmers must be concerned with second generation ECB.

As mudanças da educação do RN nos idos de 1950 e 1960 :a prática de Lia Campos

The present study investigates and analyzes the participation of the teacher Lia Campos, during the 50 s and 60 s years, in the norte-riograndense educational organization. The choice of the period is justified because was at this the time what this teacher remained in the potiguar lands, working in favor of the education. In the search of data that informed me concerning her actions, I cover quantities as the Public Archive of the Great River of the North, Historical Institute and Geographic of the Rio Grande do Norte and the Center of Supplementary Studies Teacher Lia Campos, in the task to obtain photographs and verbal stories of friends and fellow workers, periodicals of the time, laws and decrees. Based on the primary education, the work of Lia Campos shows the relevance of the teaching formation for this level of education and the way as the ones that in it work can lead their conceptions and daily practical tasks. This way, I evidence that the cited teacher promotes, in this State, a series of activities as: survey and systematization of the school net; organization of the administrative stuff of the schools; qualifications and courses of improving for lay professors, as well as implantation of the Law of the Education nº 2.171/1957. Through this analysis I show as this teacher left printed her mark in the Rio Grande do Norte historiography by means of her actions, being therefore remembered for that they had followed her experience in norte-riograndense lands

Práticas populares de cuidado à criança: o saber/fazer de cuidadoras

Popular practices correspond to the resources used by households, lay people and popular therapists, whose perception of knowledge is constructed in the everyday. In this context, the sick child can become vulnerable to be dependent on a family caregiver, who often decide to employ popular practices. Thus, the child care should be shared between carer and health professional. However, they know little about the resources that the family uses to detect a grievance in infant. Therefore, the present research aimed to analyse the use of popular practices by caregivers of children with zero to five years old. We conducted an exploratory and descriptive study with a qualitative approach, together with 15 caregivers of children who were treated at the Joint Unit Felipe Shrimp, located in Natal, Rio Grande do Norte, Brazil. To select the participants, they should be age and above 18 years; be caregivers of children up to five years of age; and reside in the area ascribed the Joint Unit Felipe Shrimp. The data collection took place between September and October 2013, through in depth interview. This step was preceded by the approval of the Health Department of the city of Natal; the direction of the Joint Unit Felipe Shrimp; as well as, the Committee on Ethics in Research from the Federal University of Rio Grande do Norte with Certificate of Presentation and Consideration Ethics, No 15467013.8.0000.5537. Furthermore, the interviewees formally authorized their participation in the research by signing the consent form. The data were treated according to the technique of content analysis in the form of thematic analysis according to Bardin. This process, four categories emerged: "Types of popular practices used in the care of the child"; "Source of information of popular practices"; "Results obtained with popular practices"; "Factors that hinder the adoption of common practices." The results showed the use of popular practices by caregivers in the case of illness to children such as the homemade preparations with medicinal plants and folk healers. The family environment was referenced as the main learning space and spread of popular practices, which are influenced by cultural relations present in this context. As to the results obtained with popular features, the caregivers said to be satisfactory, and this triggers a feeling of confidence and acceptability of such measures. It is concluded that the use of popular practices in child care persists in everyday most of the participants, despite the hegemony of allopathic therapy. The caregivers stated that such practices are effective and easy to obtain, being secured in context by popular culture. In addition, health professionals, especially nurses, were seldom mentioned by the caregivers as to the information concerning popular resources used by them, which suggests the weakness in dialogic process of negotiating practices between both of them

Triptofano na alimentação de codornas japonesas nas fases de recria e postura

Objetivou-se estudar o efeito de diferentes planos alimentares, de acordo com os níveis de triptofano, sobre o desempenho e estresse (pela avaliação de parâmetros fisiológicos) de codornas japonesas (Coturnix coturnix japonica) nas fases de recria e postura. Cento e noventa e duas codornas japonesas na fase de recria (30 a 44 dias de idade) foram alojadas em gaiolas e distribuídas em um delineamento em blocos casualizados, com quatro planos de nutrição [0,27 (controle); 0,52; 0,77 ou 1,02% de triptofano], seis repetições e oito aves por parcela. Foram avaliados os parâmetros de desempenho (consumo de ração, ganho de médio peso, conversão alimentar e taxa de mortalidade) e os parâmetros fisiológicos das aves (relação heterófilo/linfócito e concentração de corticosterona no plasma sangüíneo). Outras 192 codornas japonesas na fase de postura (45 a 146 dias) foram distribuídas em delineamento de blocos ao acaso e submetidas a quatro planos de nutrição (0,23 [controle]; 0,48; 0,73 ou 0,98% de triptofano), com seis repetições e oito aves por parcela. Foram avaliados o consumo de ração, a produção de ovos, a conversão alimentar por dúzia de ovos, a taxa de mortalidade, a relação heterófilo/linfócito e a concentração de corticosterona no plasma. Os níveis de triptofano testados não afetaram o desempenho e os parâmetros fisiológicos de codornas japonesas nas fases de recria e postura.

S-Educ: Um Simulador de Ambiente de Robótica Educacional em Plataforma Virtual

We propose a robotics simulation platform, named S-Educ, developed specifically for application in educational robotics, which can be used as an alternative or in association with robotics kits in classes involving the use of robotics. In the usually known approach, educational robotics uses robotics kits for classes which generally include interdisciplinary themes. The idea of this work is not to replace these kits, but to use the developed simulator as an alternative, where, for some reason, the traditional kits cannot be used, or even to use the platform in association with these kits. To develop the simulator, initially, we conducted research in the literature on the use of robotic simulators and robotic kits, facing the education sector, from which it was possible to define a set of features considered important for creating such a tool. Then, on the software development phase, the simulator S-Educ was implemented, taking into account the requirements and features defined in the design phase. Finally, to validate the platform, several tests were conducted with teachers, students and lay adults, in which it was used the simulator S-Educ, to evaluate its use in educational robotics classes. The results show that robotic simulator allows a reduction of financial costs, facilitate testing and reduce robot damage inherent to its use, in addition to other advantages. Furthermore, as a contribution to the community, the proposed tool can be used to increase adhesion of Brazilian schools to the methodologies of educational robotics or to robotics competitions

Efeitos do envelhecimento ambiental acelerado em compósitos poliméricos

The advantages of the use of vegetable fibers on the synthetic fibers, such as glass fibers, in the reinforcements in composites are: low cost, low density, good tenacity, good thermal properties and reduced use of instruments for their treatment or processing. However, problems related to poor performance of some mechanical natural fibers, have hindered its direct use in structural elements. In this sense, the emergence of alternative materials such as hybrids composites, involving natural and synthetic fibers, has been encouraged by seeking to improve the performance of structural composites based only on natural fibers. The differences between the physical, chemical and mechanical properties of these fibers, especially facing the adverse environmental conditions such as the presence of moisture and ultraviolet radiation, is also becoming a concern in the final response of these composites. This piece of research presents a comparative study of the strength and stiffness between two composite, both of ortoftalic polyester matrix, one reinforced with fibers of glass-E (CV) and other hybrid reinforced with natural fibers of curauá and fiberglass-E (CH). All the comparative study is based on the influence of exposure to UV rays and steam heated water in composites, simulating the aging environment. The conditions for the tests are accelerated through the use of the aging chamber. The composites will be evaluated through tests of uniaxial static mechanical traction and bending on three points. The composite of glass fiber and hybrid manufacturing industry are using the rolling manual (hand lay-up) and have been developed in the form of composites. All were designed to meet possible structural applications such as tanks and pipes. The reinforcements used in composites were in the forms of short fiber glass-E quilts (450g/m2 - 5cm) of continuous wires and fuses (whose title was of 0.9 dtex) for the curauá fibers. The results clearly show the influence of aging on the environmental mechanical performance of the composite CV and CH. The issues concerning the final characteristics of the fracture for all types of cargoes studied were also analyzed

Capacidade de absorção de energia de tubos de compósitos submetidos à compressão

Structures capable of absorbing large amounts of energy are of great interest, particularly for the automotive and aviation industries, to reduce tbe impact on passengers in the case of a collision. The energy absorption properties of composite materials structures can be tailored, thus making these structures an appealing option a substitute of more traditional structures in applications where energy absorption is crucial. ln this research, the influence of some parameters, which affect the energy absorption capacity of composite material tubes, was investigated. The tubes were fabricated by hand lay-up, using orthophthalic polyester resin and a plain weave E-glass fabric Test specimens were prepared and tested under compression load. The ínfluence of the following parameters on the specific energy absorption capacity of the tubes was studied: fiber configuration (0/90º or ± 45°), tube cross-section (circular or square), and processing conditions (with or without vacuum). The results indicated that circular cross-section tubes with fibers oriented at 0/90º presented the highest level of specific energy absorbed. Further, specimens from tubes fabricated under vacuum displayed higher energy absorption capacity, when compared with specimens from tubes fabricated without vacuum. Thus, it can be concluded that the fabrication process with vacuum produce composite structures with better energy absorption capacity

Envelhecimento ambiental acelerado em PRF a base de tecidos híbridos kevlar/vidro: propriedades e instabilidade estrutural

There are a number of damaging mechanisms that various materials can suffer in service. However, when working with polymer composite materials, this is something that requires analysis, especially when exposed to adverse environmental conditions. Thus, the objective of the present thesis is the study of the direct influence of environmental aging and the form of hybridization of the reinforcement woven on the structural stability, surfacedegradation and fracture process of polymer composites laminates. For this, the development of two polymer composite laminates was necessary, where one of them was reinforced with a bi-directional woven with hybrid strandsofkevlar-49/glass-Efibers, and the other also with a bi-directionalwoven, however with weft and warpformed of alternating strandsof Kevlar-49 fibers and glass-E fiber The reinforcementwoven are industrially manufactured. Both laminates use a polyester resin as a matrixand are made up of four layers each. All laminates were industrially prepared by the hand lay-up method of manufacturing. To do this, test specimens were manufactured of the respective laminates and submitted to environmental aging accelerated through the aging chamber. They were exposed to alternating cycles of UV radiation and moisture (heated steam) for a standard defined period. At the end of the exposure period the specimens were subjected to mechanical tests of uniaxial tensile and bending in three points and to the characterizationsof the fracture and surface deterioration. In addition, they were submitted to a structural degradation assessment by the measurement of mass variation technique (MMVT) and the measurement of thickness variation technique (MTVT), this last technique being developed in this thesis. At the end of the analysis it was observed that the form of hybridization of the reinforcement woven and the aging process directly influence with losses or gain in mechanical properties, with losses in the structural degradation and in the formation and propagation of damage mechanism of the developedcomposite laminates

Desenvolvimento de um laminado compósito híbrido a base de fibras de vidro/licurí

This research work is based, in search of reinforcement s vegetable alternative to polymer composites. The idealization of making a hybrid composite reinforced with vegetable fibers licuri with synthetic fibers is a pioneer in this area. Thus was conceived a hybrid composite laminate consisting of 05 (five) layers being 03 (three) webs of synthetic fibers of glass and E-02 (two) unidirectional fabrics of vegetable fibers licuri. In the configuration of the laminate layers have alternating distribution. The composite laminate was manufactured in Tecniplas Commerce & Industry LTD, in the form of a card through the manufacturing process of hand lay up. Licuri fibers used in making the foil were the City of Mare Island in the state of Bahia. After cooking and the idealization of the hybrid composite laminate, the objective of this research work has focused on evaluating the performance of the mechanical properties (ultimate strength, stiffness and elongation at break) through uniaxial tensile tests and three point bending. Comparative studies of the mechanical properties and as well as among other types of laminated hybrid composites studied previously, were performed. Promising results were found with respect to the mechanical properties of strength and stiffness to the hybridization process idealized here. To complement the entire study were analyzed in terms of macroscopic and microscopic characteristics of the fracture for all tests.

Compósito Polimérico Híbrido: Comportamento Mecãnico, Descotinuidade Geométrica e Resistência Residual

The growing demand in the use of hybrid composite materials makes it essential a better understanding of their behavior face of various design conditions, such as the presence of geometric discontinuities in the cross section of structural elements. This way, the purpose of this dissertation is a study of the mechanical response (strength and stiffness), modes (characteristics) of fracture and Residual Strength of an hybrid polymeric composite with and without a geometric discontinuity in its longitudinal section (with a reduction in the cross section) loaded by uniaxial tension. This geometric discontinuity is characterized by central holes of different diameters. The hybrid composite was fabricated as laminate (plate) and consisting of ortho-tereftalic polyester matrix reinforced by 04 outer layers of Jute fibers bidirectional fabrics and 01 central layer of E-glass bidirectional fabric. The laminate was industrially manufactured (Tecniplas Nordeste Indústria e Comércio Ltda.), obtained by the hand lay-up technique. Initially, a study of the volumetric density of the laminate was made in order to verify its use in lightweight structures. Also were performed comparative studies on the mechanical properties and fracture modes under the conditions of the specimens without the central hole and with the different holes. For evaluating the possible influence of the holes in the structural stability of the laminate, the Residual Strength of the composite was determined for each case of variation in hole diameter. As a complementary study, analyses of the macroscopic final fracture characteristic of the laminates were developed. The presence of the central hole of any sizes, negatively changed the ultimate tensile strength. Regarding the elastic modulus, moreover, the difference found between the specimens was within the range of tests displacement, showing the laminate stability related to the stiffness

Influência da umidade nas propriedades mecânicas dos compósitos poliméricos híbridos (sisal/ vidro)

This study aims to evaluate the mechanical properties of polymer matrix composites reinforced with sisal fabric bidirectional tissue (Agave sisalana,) and E-glass fibers, containing the following configuration: a polymer matrix hybrid composite (Polyester Resin orthophalic) reinforced with three (3) layers of glass fibers and alternating-2 (two) layers of bidirectional sisal fabric, and finally a composite of polymer matrix reinforced with five (5) layers of glass fiber mat-type E. For this purpose as first step, the preparation of by sisal, since they are not on the market. The composites were made by manual lamination (Hand lay-up) and evaluated for tensile properties and three point bending both in the dry, and wet conditions aswele as immersed in oil. Macroscopic and microscopic characteristics of the materialsweve awalysed, after the completion of the mechanical tests. After the studies, it was proven that the sisal fiber decreases the tensile stiffness of the material above 50% for both situations studied the tensile strength of the material decreases by approximately 40% for the cases mentioned, and when compared to the specific strength stiffness values drop to 14.6% and 29.02% respectively for the dry state only. Constants for bending the values were are to approximately 50% to 25% for strength and stiffness of the material for the cases dry, wet and immersed in oil. Under the influence of tension fluids do not interfere in the stiffness of the material for the bending tests, the same does not occur with the resistance, and these values are modified only in the cases stiffness and flexural strength

Envelhecimento ambiental em compósitos poliméricos à base de tecidos de reforços híbridos

The utilization of synthetic fibers for plastic reinforcement is more and more frequent and this growing interest requires that their mechanic behavior under the most variable conditions of structural applications be known. The use of such materials in the open and exposed to the elements is one of them. In this case, it becomes extremely necessary to study their mechanical properties (strength, stiffness) and the mechanism of fracture by which the environment aging them out. In order to do that, the material must be submitted to hot steam and ultraviolet radiation exposure cycles, according to periods of time determined by the norms. This study proposal deals with the investigation of accelerated environmental aging in two laminated polymeric composites reinforced by hybrid woven made up of synthetic fibers. The configurations of the laminated composites are defined as: one laminate reinforced with hybrid woven of glass fibers/E and Kevlar fibers/49 (LHVK) and the other laminate is reinforced with hybrid tissue of glass fibers/E and of carbon fibers AS4 (LHVC). The woven are plane and bidirectional. Both laminates are impregnated with a thermofix resin called Derakane 470-300 Epoxy Vinyl-Ester and they form a total of four layers. The laminates were industrially manufactured and were made through the process of hand-lay-up. Comparative analyses were carried out between their mechanical properties by submitting specimen to uniaxial loading tractions and three-point flexion. The specimen were tested both from their original state, that is, without being environmentally aging out, and after environmental aging. This last state was reached by using the environmental aging chamber

Tubulações de PRFV com adição de areia quartzosa visando sua aplicação na indústria do petróleo

Fillers are often added in composites to enhance performance and/or to reduce cost. Fiberglass pipes must meet performance requirements and industrial sand is frequently added for the pipe to be cost competitive. The sand is added to increase pipe wall thickness, thus increase pipe stiffness. The main goal of the present work is to conduct an experimental investigation between pipes fabricated with and without de addition of sand, to be used in the petroleum industry. Pipes were built using E-glass fibers, polyester resin and siliceous sand. The fabrication process used hand lay up and filament winding and was divided in two different parts: the liner and the structural wall. All tested pipes had the same liner, but different structural wall composition, which is the layer where siliceous sand may be added or not. The comparative investigation was developed considering the results of longitudinal tensile tests, hoop tensile tests, hydrostatic pressure leak tests and parallel-plate loading stiffness tests. SEM was used to analyze if the sand caused any damage to the glass fibers, during the fabrication process, because of the fiber-sand contact. The procedure was also used to verify the composite conditions after the hydrostatic pressure leak test. The results proved that the addition of siliceous sand reduced the leak pressure in about 17 %. In the other hand, this loss in pressure was compensated by a stiffness increment of more than 380 %. MEV analyses show that it is possible to find damage on the fiber-sand contact, but on a very small amount. On most cases, the contact occurs without damage evidences. In summary, the addition of sand filler represented a 27.8 % of cost reduction, when compared to a pipe designed with glass fiber and resin only. This cost reduction combined to the good mechanical tests results make siliceous sand filler suitable for fiberglass pressure pipes

Projeto e Operação em Escala Semi-Industrial de um Equipamento para Tratamento de Águas Produzidas na Indústria do Petróleo Utilizando Nova Tecnologia: misturador-decantador à inversão de fases - MDIF

The aim of this work is to use a new technology in the treatment of produced wastewaters from oil industry. An unit for treat produced waters called UTMDIF, was designed, installed and operated in an industrial plant for treatment of effluents from oil industry. This unit operates by means of the method of separation of phase inversion and can become a promising alternative to solve the problem of oil/water separation. This method constitutes the basis of the working of a new design of mixersettler of vertical configuration which occupies small surface area. The last characteristic becomes specially important when there is limitation on the lay-out of the plant, for example, over maritime platforms to explore oil. This equipment in a semi-industrial scale treats produced wastewaters contaminated with oil at low concentrations (ranging from 30 to 150 mg/L) and throughputs of 320 m3/d (47,4 m3 m-2 h-1). Good results were obtained in oil/water separation which leads to the necessary specification to discharge those wastewaters. Besides, the non dependence of the efficiency of separation in spite of the salinity of the medium becomes the equipment an attractive new technology to treat wastewaters containing oil at low concentrations

Estudo da secagem do pedúnculo do caju em sistemas convencional e solar: modelagem e simulação do processo

This work aims to study the drying of cashew-nut pulp with different lay-out of dryers using conventional and solar energy. It concerns with the use of exceeding of the regional raw material and the suitable knowledge for the applicability of the drying systems as pathway for food conservation. Besides, it used renewable sources as solar energy to dry these agroindustrial products. Runs were carried out using a conventional tray-dryer with temperature, air velocity control and cashew slice thickness of 55°C, 65°C, 75°C; 3.0; 4.5, 6.0 m s-1; 1.0; 1.5 and 2.0 cm, respectively, in order to compare the studied systems. To evaluate the conventional tray-dryer, it was used a diffusional model of 2nd Fick´s law, where the drying curves were quite well fitted to an infinite flat plate design. For the drying runs where the room temperature had no control, it was developed a phenomenological-mathematical model for the solar dryer with indirect radiation under natural and forced convection based on material and energy balances of the system. Besides, it was carried out assays in the in natura as well as dehydrated, statistic analysis of the experimental drying data, sensorial analysis of the final dry product and a simplified economical analysis of the systems studied