Comparison of indigestible markers from in situ and in vivo incubation to predict apparent digestibility in hay- and corn-fed horses

Four castrated crossbred horses were used in a randomized block design to study the use of indigestible internal markers iNDF and iADF obtained in situ (from bovines) or in vivo (from equines). Treatments consisted of determining digestibility by the direct method comprising total feces collection (TC) and by the indirect method comprising internal markers iNDF and iADF obtained by in situ incubation in bovine rumen or in vivo by the mobile nylon bag (MNB) technique with horses. iNDF-IV and iADF-IV resulted in better marker recovery rate (RR) (91.50%), similar to TC. The in situ technique resulted in lower RR values for the two indigestible markers, averaging 86.50% (p < 0.05). Estimates of the nutrient coefficient of digestibility (CD) were adequately predicted by iADF-IV, for horses fed on hay exclusively, with rates 46.41, 48.16, 47.92 and 45.51% for dry matter (DM), organic matter (OM), FDN and gross energy, respectively. Results show that MNB may be used to obtain iADF in horses fed on coast-cross hay exclusively, whereas NDFi and ADFi were selected for horses fed on mixed diets to predict the coefficient of nutrient digestibility.

In-situ XANES experiments on Ni K-edge in mesoporous ZrO2-CeO2:Ni.

Ordered mesoporous ZrO2-CeO2 mixed oxides are potential candidates for catalytic applications. These systems, used as anodes in solid oxide fuel cells (SOFC), may lead to better performance of SOFCs, due to an enhancement on surface area, aiming to achieve a lower working temperature. The aim of this studies is to evaluate the reduction capacity of Ni2+ to Ni in ZrO2-x(mol)%CeO2 (x=50 and 90) samples impregnated with 60(wt.)%NiO. The synthesis was made with Zr and Ce chloride precursors, HCl aqueous solution, Pluronic P123, NH4OH to adjust the pH (3-4) and a teflon autoclave to perform a hydrothermal treatment (80oC/48h). The samples were dried and calcined, until 540oC in N2 and 4 hours in air. The NiO impregnation was made with an ethanol dispersion of Ni(NO3)£6H2O. The powder was calcinated in air until 350oC for 2 hours. Temperature-resolved XANES data at the Ni K-edge were collected at the DXAS beam line of the LNLS in transmission mode, using a Si(111) monochromator and a CCD detector. Sample preparation consisted of mixing »6mg of the powder samples with boron nitride and pressing into pellets. The data were acquired during an experiment of temperature programmed reduction (TPR) under a 5% H2/He until 600oC and mixtures of 20%CH4:5%O2/He, at temperatures from 400 to 600oC. All the reactions were monitored with a mass spectrometer. The data was analyzed with a linear combination fit of 2 standards for each valence number using Athena software. The Ni K-edge experiments demonstrated that for both contents of CeO2, NiO embedded in the porous zirconia-ceria matrix reduces at lower temperatures than pure NiO, revealing that the ZrO2-CeO2 support improves the reduction of impregnated NiO. Ni was oxidized to NiO after all reactions with methane and oxygen. Hydrogenated carbonaceous species were detected, but under reducing conditions, the hydrocarbon compounds are removed. The reaction of total oxidation of methane CH4:O2 (1:2 ratio) was observed at lower temperatures (around 400oC) for both samples.

Effects of flavomycin on ruminal fermentation, In situ degradability and In vivo digestibility in bovine fed sugarcane diets

Problem statement: The aim of the present study was to characterize and differentiate the effects of addition of flavomycin or monensin on ruminal fermentation and degradability as well as on total digestibility in bovine. Approach: Twelve non-pregnant and non-lactating cows (736 kg of BW) were randomly assigned to three treatments: control, flavomycin (20 mg animal-1 day-1) and monensin (300 mg animal-1 day-1). The trial lasted 21 days. The last 10 days were used for external marker administration (15 g of chromic oxide animal-1 day-1). The last 5 days of the trial were used for feces collection and evaluation of corn grain, soybean meal or sugarcane ruminal degradability and the 21st day was used for ruminal fluid sampling. Results: Monensin increased 27.2%, on average, propionate molar proportion at 0, 4, 6, 8, 10 and 12 h after feeding, compared to control and flavomycin groups. When compared to control, flavomycin reduced the degradation rate of soybean meal CP in 31.0%, decreasing the effective degradability when passage rates of 5 and 8% h-1 were used. Dry matter intake, pH, total Short Chain Fatty Acids (tSCFA) or ammoniacal Nitrogen (NH3-N) concentration were not influenced by the addition of either antibiotics. Effective degradability of sugarcane NDF was not influenced by the use of either antibiotic; neither were the TDN nor the digestibility of DM, CP, EE, NFE, ADF, NDF, GE or starch of the diet. Conclusion/Recommendations: In the present study, it was possible to show the beneficial effects of monensin but not of flavomycin, on rumen fermentation

Reactive sputter magnetron reactor for preparation of thin films and simultaneous in-situ structural study by X-ray diffraction.

Reactive Sputter Magnetron (RSM) is a widely used technique to thin films growing of compounds both, in research laboratories and in industrial processes. The nature of the deposited compound will depend then on the nature of the magnetron target and the nature of the ions generated in the plasma. One important aspect of the problem is the knowledge of the evolution of the film during the process of growing itself. In this work, we present the design, construction of a chamber to be installed in the Huber goniometer in the XRD2 line of LNLS in Campinas, which allows in situ growing kinetic studies of thin films.

Construção de perfis de temperatura a partir de dados de Satélites,Climatologia e dados in situ

A aquisição de dados da estrutura termohalina dos oceanos sempre foi limitada pelo alto custo das missões oceanográficas. Sistemas de amostragem in situ menos dispendiosos, como o lançamento de XBTs por navios de oportunidade, a utilização de bóias de deriva, e mais recentemente, de sistemas de observação autõnomos como gliders e flutuadores Argo, foram concebidos como alternativas aos cruzeiros. Estes sistemas são capazes de cobrir vastas porções oceanicas e de fornecer grande quantidade de medições, porem seus dados nem sempre estão disponíveis ou mesmo são adequados `a resolução de um determinado problema ou ao estudo de um fenômeno em questão, devido principalmente à sua falta de sinopticidade e/ou cobertura espacial irregular. Sensores orbitais provaram ser valiosos e comparativamente possuem excelente periodicidade e cobertura espacial, mas suas observações são limitadas apenas à superfície dos oceanos. Assim, a capacidade de se inferir com boa precisão a estrutura termohalina de feições oceanográficas à partir de uma amostragem reduzida e/ou utilizando medições¸ indiretas é desejável e vem sido aprimorada em diversos trabalhos. Métodos clássicos incluem o desenvolvimento de modelos de feição pelo ajuste de curvas paramétricas (e.g. GANGOPADHYAY et al., 1997; CHU et al., 1999) e a reconstrução de perfis utilizando modos EOF (e.g. CARNES et al., 1990; AGARWAL et al., 2007)

In situ and remote sensing signature of meddies east of the mid-Atlantic ridge

[EN] Mediterranean Water eddies (meddies) are thought to play an important climatic role. Nevertheless, their dynamics are not sufficiently known because of difficulties encountered in their observation. Though propagating below the main thermocline, a number of pieces of evidence of sea surface manifestation of meddies are collected. The present work is based on joint in situ and altimetry data analyses to prove that the meddies can be followed with remote sensing data for long periods of time. The in situ observations are based on data from an oceanographic cruise, which crossed three meddies, and reanalysis of historical data sets, including RAFOS floats paths. Suggested methodology permitted us to obtain uninterrupted tracks for several meddies for a period from several months to more than 2 years. It was found that the dynamically calm region to the north of the Azores current presents favorable conditions for meddy tracking. The meddy surface signal may become shattered and difficult to follow during interaction with a strong dynamic structures (the Azores current/surface vortexes) or peaking topography. Theoretical considerations support the observations and lead to the conclusion that the dynamic signature of meddies at the sea surface is an intrinsic property of meddy dynamics

Design of wireless sensor networks for fluid dynamic applications

In fluid dynamics research, pressure measurements are of great importance to define the flow field acting on aerodynamic surfaces. In fact the experimental approach is fundamental to avoid the complexity of the mathematical models for predicting the fluid phenomena. It’s important to note that, using in-situ sensor to monitor pressure on large domains with highly unsteady flows, several problems are encountered working with the classical techniques due to the transducer cost, the intrusiveness, the time response and the operating range. An interesting approach for satisfying the previously reported sensor requirements is to implement a sensor network capable of acquiring pressure data on aerodynamic surface using a wireless communication system able to collect the pressure data with the lowest environmental–invasion level possible. In this thesis a wireless sensor network for fluid fields pressure has been designed, built and tested. To develop the system, a capacitive pressure sensor, based on polymeric membrane, and read out circuitry, based on microcontroller, have been designed, built and tested. The wireless communication has been performed using the Zensys Z-WAVE platform, and network and data management have been implemented. Finally, the full embedded system with antenna has been created. As a proof of concept, the monitoring of pressure on the top of the mainsail in a sailboat has been chosen as working example.

Cooperative communication and distributed detection in wireless sensor networks

Recent progress in microelectronic and wireless communications have enabled the development of low cost, low power, multifunctional sensors, which has allowed the birth of new type of networks named wireless sensor networks (WSNs). The main features of such networks are: the nodes can be positioned randomly over a given field with a high density; each node operates both like sensor (for collection of environmental data) as well as transceiver (for transmission of information to the data retrieval); the nodes have limited energy resources. The use of wireless communications and the small size of nodes, make this type of networks suitable for a large number of applications. For example, sensor nodes can be used to monitor a high risk region, as near a volcano; in a hospital they could be used to monitor physical conditions of patients. For each of these possible application scenarios, it is necessary to guarantee a trade-off between energy consumptions and communication reliability. The thesis investigates the use of WSNs in two possible scenarios and for each of them suggests a solution that permits to solve relating problems considering the trade-off introduced. The first scenario considers a network with a high number of nodes deployed in a given geographical area without detailed planning that have to transmit data toward a coordinator node, named sink, that we assume to be located onboard an unmanned aerial vehicle (UAV). This is a practical example of reachback communication, characterized by the high density of nodes that have to transmit data reliably and efficiently towards a far receiver. It is considered that each node transmits a common shared message directly to the receiver onboard the UAV whenever it receives a broadcast message (triggered for example by the vehicle). We assume that the communication channels between the local nodes and the receiver are subject to fading and noise. The receiver onboard the UAV must be able to fuse the weak and noisy signals in a coherent way to receive the data reliably. It is proposed a cooperative diversity concept as an effective solution to the reachback problem. In particular, it is considered a spread spectrum (SS) transmission scheme in conjunction with a fusion center that can exploit cooperative diversity, without requiring stringent synchronization between nodes. The idea consists of simultaneous transmission of the common message among the nodes and a Rake reception at the fusion center. The proposed solution is mainly motivated by two goals: the necessity to have simple nodes (to this aim we move the computational complexity to the receiver onboard the UAV), and the importance to guarantee high levels of energy efficiency of the network, thus increasing the network lifetime. The proposed scheme is analyzed in order to better understand the effectiveness of the approach presented. The performance metrics considered are both the theoretical limit on the maximum amount of data that can be collected by the receiver, as well as the error probability with a given modulation scheme. Since we deal with a WSN, both of these performance are evaluated taking into consideration the energy efficiency of the network. The second scenario considers the use of a chain network for the detection of fires by using nodes that have a double function of sensors and routers. The first one is relative to the monitoring of a temperature parameter that allows to take a local binary decision of target (fire) absent/present. The second one considers that each node receives a decision made by the previous node of the chain, compares this with that deriving by the observation of the phenomenon, and transmits the final result to the next node. The chain ends at the sink node that transmits the received decision to the user. In this network the goals are to limit throughput in each sensor-to-sensor link and minimize probability of error at the last stage of the chain. This is a typical scenario of distributed detection. To obtain good performance it is necessary to define some fusion rules for each node to summarize local observations and decisions of the previous nodes, to get a final decision that it is transmitted to the next node. WSNs have been studied also under a practical point of view, describing both the main characteristics of IEEE802:15:4 standard and two commercial WSN platforms. By using a commercial WSN platform it is realized an agricultural application that has been tested in a six months on-field experimentation.

Physical and mineralogical changes of Hungarian monumental stones exposed to different conditions: stone-testing in-situ and under laboratory conditions

The Székesfehérvár Ruin Garden is a unique assemblage of monuments belonging to the cultural heritage of Hungary due to its important role in the Middle Ages as the coronation and burial church of the Kings of the Hungarian Christian Kingdom. It has been nominated for “National Monument” and as a consequence, its protection in the present and future is required. Moreover, it was reconstructed and expanded several times throughout Hungarian history. By a quick overview of the current state of the monument, the presence of several lithotypes can be found among the remained building and decorative stones. Therefore, the research related to the materials is crucial not only for the conservation of that specific monument but also for other historic structures in Central Europe. The current research is divided in three main parts: i) description of lithologies and their provenance, ii) physical properties testing of historic material and iii) durability tests of analogous stones obtained from active quarries. The survey of the National Monument of Székesfehérvár, focuses on the historical importance and the architecture of the monument, the different construction periods, the identification of the different building stones and their distribution in the remaining parts of the monument and it also included provenance analyses. The second one was the in situ and laboratory testing of physical properties of historic material. As a final phase samples were taken from local quarries with similar physical and mineralogical characteristics to the ones used in the monument. The three studied lithologies are: fine oolitic limestone, a coarse oolitic limestone and a red compact limestone. These stones were used for rock mechanical and durability tests under laboratory conditions. The following techniques were used: a) in-situ: Schmidt Hammer Values, moisture content measurements, DRMS, mapping (construction ages, lithotypes, weathering forms) b) laboratory: petrographic analysis, XRD, determination of real density by means of helium pycnometer and bulk density by means of mercury pycnometer, pore size distribution by mercury intrusion porosimetry and by nitrogen adsorption, water absorption, determination of open porosity, DRMS, frost resistance, ultrasonic pulse velocity test, uniaxial compressive strength test and dynamic modulus of elasticity. The results show that initial uniaxial compressive strength is not necessarily a clear indicator of the stone durability. Bedding and other lithological heterogeneities can influence the strength and durability of individual specimens. In addition, long-term behaviour is influenced by exposure conditions, fabric and, especially, the pore size distribution of each sample. Therefore, a statistic evaluation of the results is highly recommended and they should be evaluated in combination with other investigations on internal structure and micro-scale heterogeneities of the material, such as petrographic observation, ultrasound pulse velocity and porosimetry. Laboratory tests used to estimate the durability of natural stone may give a good guidance to its short-term performance but they should not be taken as an ultimate indication of the long-term behaviour of the stone. The interdisciplinary study of the results confirms that stones in the monument show deterioration in terms of mineralogy, fabric and physical properties in comparison with quarried stones. Moreover stone-testing proves compatibility between quarried and historical stones. Good correlation is observed between the non-destructive-techniques and laboratory tests results which allow us to minimize sampling and assessing the condition of the materials. Concluding, this research can contribute to the diagnostic knowledge for further studies that are needed in order to evaluate the effect of recent and future protective measures.

In-situ-Hochtemperatur-Mössbauer-Spektroskopie und Bandstruktur-Rechnungen an Eisennitriden und gemischtvalenten Verbindungen

Zusammenfassung

Die stöchiometrischen Eisennitride g'-Fe₄N, e-Fe₃N und z-Fe₂N sind durchRöntgen- und Neutronenstreuung gut charakterisiert. Allerdings weist das Fe/N-Phasendiagramm noch vieleungeklärte Stellen auf. So konnten im Bereich von alpha-Fe bis g'-Fe₄N noch keine weiterenNitride isoliert werden. Die Verbindung a''-Fe₁₆N₂ konntenoch nicht rein darzustellen werden.

Besonderes Interesse besteht in der Aufklärung desMechanismus der Entstehung der Eisennitride bei derUmsetzung von a-Eisen mitAmmoniak. Diese Reaktion wird großtechnisch zurNitridierhärtung von Eisenwerkstücken genutzt.

Als Messmethode wurde die⁵⁷Fe-Mößbauer-Spektroskopiegewählt, die auf Kernspinübergängen von⁵⁷Fe beruht. Um in situ-Nitridierungen von Eisenproben mit Ammoniak mitder ⁵⁷Fe-Mößbauer-Spektroskopieverfolgen zu können, wurde eineHochtemperatur-Messzelle entwickelt, die es erlaubt,Messungen bis 1100 K durchzuführen. Die Messzelle wurde durch Messungen an Eisennitriden mitbekannter Stöchiometrie, wie z.B. g'-Fe₄N und e-Fe₃N, durchgeführt.

Neben ⁵⁷Fe-Mößbauer-Messungen wurdenim Rahmen des DFG-Schwerpunkt-Programms Reaktivitätin Festkörpern weitere Messungen (u.a.Hochtemperatur-Leitfähigkeitsmessungen)durchgeführt.

Die experimentellen Methoden wurden durchBandstruktur-Rechnungen ergänzt. Mit Hilfe der TB-LMTO-ASA-Methode erfolgten Rechnungen anÜbergangsmetallnitriden M₃N (M = Mn, Fe, Co,Ni, Cu) der 3d-Reihe. Hierbei konnte der experimentell bestimmte strukturelleÜbergang von hexagonalem Ni₃N zu kubischemCu₃N bestätigt werden.

In-situ-Präparation von komplexen supraleitenden und ferroelektrischen Heterostrukturen mittels gepulster Laser-Deposition

In der vorliegenden Arbeit ist die Konstruktion und der Aufbau eines Systems zur gepulsten Laserablation von dünnen Schichten beschrieben. Die hohe Flexibilität der Anlage wird ermöglicht durch einen sechsfach-Targethalter und eine Heizerkonstruktion, die einfachen Substrateinbau, hohe Temperaturhomogenität und einen zugänglichen Temperaturbereich von bis zu 1000°C erlaubt. Durch eine komplexe Laser-Optik, die eine homogene Energiedichte auf dem Target sicherstellt, wird eine optimale Filmqualität erreicht.Durch die Entwicklung einer zweistufigen Prozeßführung für Y-stabilisiertes ZrO2 wird eine Wachstumsbasis hoher kristalliner Qualität für funktionale Oxidschichten auf Silizium zur Verfügung gestellt. Es zeigt sich, daß die dielektrischen Eigenschaften der YSZ Schicht stark vom Sauerstoffgehalt, der Grenzflächenmorphologie sowie der Dicke der ersten Schicht abhängig sind. Basierend auf dieser Schicht wurde BaZrO3 als zusätzliche Pufferschicht für den Hochtemperatursupraleiter (HTSL) YBa2Cu3O7 ? untersucht. Unter Verwendung von SrTiO3 Substraten konnte die dielektrische Konstante von BaZrO3 zu ? ? 65 bestimmt sowie das Dispersionsverhalten mittels modifizierter Debye-Gleichungen erklärt werden. Vergleichende Messungen auf einkristallinen SrTiO3 Substraten zeigen eine erhöhte Übergangstemperatur von 90.2 K und eine wesentliche Verbesserung der Oberflächenrauhigkeit des HTSL von 2 nm (rms) durch die Verwendung von BaZrO3 Schichten hoher Qualität. Eine nur wenige Monolagen dicke zusätzliche BaZrO3 Pufferschicht auf YSZ-gepufferten Silizium Substraten verhindert die Ausbildung von ?9° rotierten YBCO Körnern, die üblicherweise bei der direkten Deposition auf YSZ beobachtet werden. Resistive Messungen mit Übergangstemperaturen oberhalb 89 K sind vergleichbar zu Ergebnissen, die für CeO2/YSZ Pufferschichtkombinationen erreicht werden. Durch kontinuierliche Gitteranpassung wurde eine neue Schichtabfolge YBCO/CeO2/YSZ/BaZrO3 für die Erzeugung bi-epitaxialer Korngrenzen-Josephson Kontake gefunden und deren Epitaxiebeziehungen geklärt. Eine in-situ deponierte Schichtabfolge zeigt mit einer Übergangstemperatur von 91.7 K und einer Übergangsbreite von 0.15 K supraleitende Eigenschaften vergleichbar zu den besten bisher auf diesem Gebiet erreichten Ergebnissen. Voruntersuchungen zur Realisierung eines Josephsonkontaktes mit dieser Schichtabfolge zeigen jedoch, daß die erreichten Eigenschaften für die technologische Anwendung nicht ausreichend sind.Die Verwendung einer YSZ/CeO2 Pufferschichtkombination ermöglicht die Herstellung von c Achsen orientiertem ferroelektrischem SrBi2Ta2O9 auf Silizium. Im Gegensatz hierzu führt die direkte Deposition auf Silizium zu polykristallinem SrBi2Ta2O9 oder zur Ausbildung der Pyrochlor Phase, wenn nur YSZ als Pufferschicht verwendet wird. Obwohl die Polarisierung von SrBi2Ta2O9 in der ab-Ebene liegt, konnte in MFIS Strukturen ein Speicherfenster von maximal 0.87 V beobachtet werden, was eine Verbesserung um nahezu einen Faktor drei im Vergleich zu polykristallinem SrBi2Ta2O9 bedeutet. Messungen an ferroelektrischen Kondesatorstrukturen ergeben Hystereseschleifen mit einer remanenten Polarisierung von Pr = 6.5 µC/cm2 sowie einem Koerzitivfeld von Ec = 35 kV/cm. AFM Messungen im Piezo-Response Modus zeigen ferroelektrische Domänen, die durch Anlegen einer Gleichspannung reversibel umpolarisiert werden können. Im Nicht-Kontakt AFM Modus wurde die lokale Polarisierung der Schichten zu 3.4 µC/cm2 bestimmt. Weiterhin wurde eine alternative Pufferschichtkombination SrZrO3/YSZ zur Erzeugung von a-Achsen orientiertem SrBi2Ta2O9 untersucht. SrZrO3 zeigt a Achsen Orientierung in vier Wachstumsdomänen, die durch ein Model erklärt werden können. Die SrBi2Ta2O9 Schicht zeigt a Achsen sowie (116)-orientierte Körner mit derselben Domänenstruktur. Die dielektrische Konstanten von SrZrO3 und SrBi2Ta2O9 wurden zu ? ? 29 und ? ? 20 bestimmt. Die beobachteten Speicherfenster sind allerdings nicht ferroelektrischer Natur, sondern wahrscheinlich durch mobile Ionen und Ladungsfangstellen in den Pufferschichten verursacht. Die stark abgesenkte dielektrische Konstante von SrBi2Ta2O9 kann durch die im Vergleich zu polykristallinem verkleinerte Korngröße erklärt werden.

In-situ Messung großer Hydrometeore mit Hilfe der In-line-Holographie

In-situ Messung großer Hydrometeore mit Hilfe derIn-line-Holographie Diese Dissertation beschreibt die Entwicklung und Erprobungeiner Apparatur zur holographischen In-situ-Messung großerHydrometeore (HODAR). Dazu wird eine dreidimensionaleMomentaufnahme eines etwa 500 dm³ großes Meßvolumen derfreien Atmosphäre mittels der In-line-Holographieaufgezeichnet. In dieser Aufnahme kann die Größe und Formeinzelner Hydrometeore, aber auch ihre Position imMeßvolumen ausgemessen werden. Daraus sind Größen- undAbstandsverteilungen der Hydrometeore zu bestimmen. MitHilfe von Doppelbelichtungen lassen sich zusätzlich auchihre Geschwindigkeiten ermitteln.Im Verlauf dieser Arbeit werden zunächst die Hydrometeorevorgestellt. Die theoretischen Möglichkeiten einer Apparaturzur In-situ-Messung werden aus den Eigenschaften desholographischen Bildes entwickelt. Anschließend wird derverwirklichte Aufbau des HODAR erläutert. Kalibrierung undTest, sowie Messungen, die die Fähigkeiten des HODAR unterBeweis stellen, werden beschrieben.