Efficiency of nitrogen fertilizer applied at corn sowing in contrasting growing seasons in Paraguay

In order to select soil management practices that increase the nitrogen-use efficiency (NUE) in agro-ecosystems, the different indices of agronomic fertilizer efficiency must be evaluated under varied weather conditions. This study assessed the NUE indices in no-till corn in southern Paraguay. Nitrogen fertilizer rates from 0 to 180 kg ha-1 were applied in a single application at corn sowing and the crop response investigated in two growing seasons (2010 and 2011). The experimental design was a randomized block with three replications. Based on the data of grain yield, dry matter, and N uptake, the following fertilizer indices were assessed: agronomic N-use efficiency (ANE), apparent N recovery efficiency (NRE), N physiological efficiency (NPE), partial factor productivity (PFP), and partial nutrient balance (PNB). The weather conditions varied largely during the experimental period; the rainfall distribution was favorable for crop growth in the first season and unfavorable in the second. The PFP and ANE indices, as expected, decreased with increasing N fertilizer rates. A general analysis of the N fertilizer indices in the first season showed that the maximum rate (180 kg ha-1) obtained the highest corn yield and also optimized the efficiency of NPE, NRE and ANE. In the second season, under water stress, the most efficient N fertilizer rate (60 kg ha-1) was three times lower than in the first season, indicating a strong influence of weather conditions on NUE. Considering that weather instability is typical for southern Paraguay, anticipated full N fertilization at corn sowing is not recommended due the temporal variability of the optimum N fertilizer rate needed to achieve high ANE.

Filter Paper Method for the Determination of the Soil Water Retention Curve

ABSTRACT High cost and long time required to determine a retention curve by the conventional methods of the Richards Chamber and Haines Funnel limit its use; therefore, alternative methods to facilitate this routine are needed. The filter paper method to determine the soil water retention curve was evaluated and compared to the conventional method. Undisturbed samples were collected from five different soils. Using a Haines Funnel and Richards Chamber, moisture content was obtained for tensions of 2; 4; 6; 8; 10; 33; 100; 300; 700; and 1,500 kPa. In the filter paper test, the soil matric potential was obtained from the filter-paper calibration equation, and the moisture subsequently determined based on the gravimetric difference. The van Genuchten model was fitted to the observed data of soil matric potential versus moisture. Moisture values of the conventional and the filter paper methods, estimated by the van Genuchten model, were compared. The filter paper method, with R2 of 0.99, can be used to determine water retention curves of agricultural soils as an alternative to the conventional method.

Performance of Randomly Oriented, Fiber-Reinforced Roadway Soils, HR-211, 1982

Several primary techniques have been developed through which soil aggregate road material properties may be improved. Such techniques basically involve a mechanism of creating a continuous matrix system of soil and/or aggregate particles, interlocked through the use of some additive such as portland cement, lime, or bituminous products. Details by which soils are stabilized vary greatly, but they are dependent on the type of stabilizing agent and nature of the soil, though the overall approach to stabilization has the common feature that improvement is achieved by some mechanism(s) forcing individual particles to adhere to one another. This process creates a more rigid material, most often capable of resisting the influx of water during freezing, loss of strength due to high moisture content and particle dispersion during thawing, and loss of strength due to migration of fines and/or water by capillarity and pumping. The study reported herein, took a new and relatively different approach to strengthening of soils, i.e., improvement of roadway soils and/or soil-aggregate materials by structural reinforcement with randomly oriented fibers. The purpose of the study was to conduct a laboratory and field investigation into the potential of improving (a) soil-aggregate surfaced and subgrade materials, including those that are frost-prone and/or highly moisture susceptible, and (b) localized base course materials, by uniting such materials through fibrous reinforcement. The envisioned objective of the project was the development of a simple construction technique(s) that could be (a) applied on a selective basis to specific areas having a history of poor performance, or (b) used for improvement of potential base materials prior to surfacing. Little background information on such purpose and objective was available. Though the envisioned process had similarities to fibrous reinforced concrete, and to fibrous reinforced resin composites, the process was devoid of a cementitious binder matrix and thus highly dependent on the cohesive and frictional interlocking processes of a soil and/or aggregate with the fibrous reinforcement; a condition not unlike the introduction of reinforcing bars into a concrete sand/aggregate mixture without benefit of portland cement. Thus the study was also directed to answering some fundamental questions: (1) would the technique work; (2) what type or types of fibers are effective; (3) are workable fibers commercially available; and (4) can such fibers be effectively incorporated with conventional construction equipment, and employed in practical field applications? The approach to obtaining answers to these questions, was guided by the philosophy that an understanding of basic fundamentals was essential to developing a body of engineering knowledge, that would serve as the basis for eventual development of design procedures with fibrous products for the applications previously noted.

Cellular source and mechanisms of high transcriptome complexity in the Mammalian testis.

Understanding the extent of genomic transcription and its functional relevance is a central goal in genomics research. However, detailed genome-wide investigations of transcriptome complexity in major mammalian organs have been scarce. Here, using extensive RNA-seq data, we show that transcription of the genome is substantially more widespread in the testis than in other organs across representative mammals. Furthermore, we reveal that meiotic spermatocytes and especially postmeiotic round spermatids have remarkably diverse transcriptomes, which explains the high transcriptome complexity of the testis as a whole. The widespread transcriptional activity in spermatocytes and spermatids encompasses protein-coding and long noncoding RNA genes but also poorly conserves intergenic sequences, suggesting that it may not be of immediate functional relevance. Rather, our analyses of genome-wide epigenetic data suggest that this prevalent transcription, which most likely promoted the birth of new genes during evolution, is facilitated by an overall permissive chromatin in these germ cells that results from extensive chromatin remodeling.

Pattern dystrophy with high intrafamilial variability associated with Y141C mutation in the peripherin/RDS gene and successful treatment of subfoveal CNV related to multifocal pattern type with anti-VEGF (ranibizumab) intravitreal injections.

OBJECTIVE: To identify disease causing mutation in three generations of a Swiss family with pattern dystrophy and high intrafamilial variability of phenotype. To assess the effect of intravitreal ranibizumab injections in the treatment of subfoveal choroidal neovascularization associated with pattern dystrophy in one patient. METHODS: Affected family members were ascertained for phenotypic and genotypic characterization. Ophthalmic evaluations included fundus photography, autofluorescence imaging, optical coherence tomography, and International Society for Clinical Electrophysiology of Vision standard full-field electroretinography. When possible family members had genetic testing. The proband presented with choroidal neovascularization and had intravitreal injections as needed according to visual acuity and optical coherence tomography. RESULTS: Proband had a multifocal type pattern dystrophy, and his choroidal neovascularization regressed after four intravitreal injections. The vision improved from 0.8 to 1.0, and optical coherence tomography showed complete anatomical restoration. A butterfly-shaped pattern was observed in her cousin, whereas a fundus pulverulentus pattern was seen in a second cousin. Aunt had a multifocal atrophic appearance, simulating geographic atrophy in age-related macular degeneration. The Y141C mutation was identified in the peripherin/RDS gene and segregated with disease in the family. CONCLUSION: This is the first report of marked intrafamilial variation of pattern dystrophy because of peripherin/RDS Y141C mutation. Intravitreal ranibizumab injections might be a valuable treatment for associated subfoveal choroidal neovascularization.

Examination of Curing Criteria for Cold In-Place Recycling Phase 2: Measuring Temperature, Moisture, Deflection and Distress from CIR Test Section, TR-590, 2009

The previous research performed laboratory experiments to measure the impacts of the curing on the indirect tensile strength of both CIR-foam and CIR-emulsion mixtures. However, a fundamental question was raised during the previous research regarding a relationship between the field moisture content and the laboratory moisture content. Therefore, during this research, both temperature and moisture conditions were measured in the field by embedding the sensors at a midpoint and a bottom of the CIR layer. The main objectives of the research are to: (1) measure the moisture levels throughout a CIR layer and (2) develop a moisture loss index to determine the optimum curing time of CIR layer before HMA overlay. To develop a set of moisture loss indices, the moisture contents and temperatures of CIR-foam and CIR-emulsion layers were monitored for five months. Based on the limited field experiment, the following conclusions are derived: 1. The moisture content of the CIR layer can be monitored accurately using the capacitance type moisture sensor. 2. The moisture loss index for CIR layers is a viable tool in determining the optimum timing for an overlay without measuring actual moisture contents. 3. The modulus back-calculated based on the deflection measured by FWD seemed to be in a good agreement with the stiffness measured by geo-gauge. 4. The geo-gauge should be considered for measuring the stiffness of CIR layer that can be used to determine the timing of an overlay. 5. The stiffness of CIR-foam layer increased as a curing time increased and it seemed to be more influenced by a temperature than moisture content. The developed sets of moisture loss indices based on the field measurements will help pavement engineers determine an optimum timing of an overlay without continually measuring moisture conditions in the field using a nuclear gauge.

Courses of study for high schools : economics, 1930

This course of study is one of a series of curriculum publications presented to high schools. The use of the course of study in the development of proper pupil attitudes, ideals, habits and skills was the criterion for selecting and evaluation subject matter material.

Association of urethral toxicity with dose exposure in combined high-dose-rate brachytherapy and intensity-modulated radiation therapy in intermediate- and high-risk prostate cancer.

INTRODUCTION: To report acute and late toxicities in patients with intermediate- and high-risk prostate cancer treated with combined high-dose-rate brachytherapy (HDR-B) and intensity-modulated radiation therapy (IMRT). MATERIALS AND METHODS: From March 2003 to September 2005, 64 men were treated with a single implant HDR-B with 21 Gy given in three fractions, followed by 50 Gy IMRT along with organ tracking. Median age was 66.1 years, and risk of recurrence was intermediate in 47% of the patients or high in 53% of the patients. Androgen deprivation therapy was received by 69% of the patients. Toxicity was scored according to the CTCAE version 3.0. Median follow-up was 3.1 years. RESULTS: Acute grade 3 genitourinary (GU) toxicity was observed in 7.8% of the patients, and late grades 3 and 4 GU toxicity was observed in 10.9% and 1.6% of the patients. Acute grade 3 gastrointestinal (GI) toxicity was experienced by 1.6% of the patients, and late grade 3 GI toxicity was absent. The urethral V(120) (urethral volume receiving > or =120% of the prescribed HDR-B dose) was associated with acute (P=.047) and late > or = grade 2 GU toxicities (P=.049). CONCLUSIONS: Late grades 3 and 4GU toxicity occurred in 10.9% and 1.6% of the patients after HDR-B followed by IMRT in association with the irradiated urethral volume. The impact of V(120) on GU toxicity should be validated in further studies.

High-precision dating and origin of synsedimentary volcanism in the Late Carboniferous Salvan-Dorenaz basin (Aiguilles-Rouges Massif, Western Alps)

Late Variscan volcanic activity is documented in the Late Carboniferous Salvan-Dorenaz sedimentary basin and in the neighboring basement units of the Aiguilles-Rouges and Mont-Blanc crystalline massifs (Western Alps). Precise U/Pb isotopic dating, zircon morphology and geochemical analyses indicate that volcanism occurred during short-lived pulses and that coexisting crustal and mantle sources were involved in the production of melts. Volcanic and subvolcanic products were emplaced along major N-S to NNE-SSW transtensional fracture zones, similar to the ones that governed intense basement exhumation and that favored the formation and filling of the Late Carboniferous Salvan-Dorenaz continental basin. In the Aiguilles-Rouges massif, dacitic flows outcropping at the base of the Salvan-Dorenaz basin erupted at 308 +/- 3 Ma; they represent the surface equivalent of the nearby Vallorcine peraluminous granite and associated rhyolitic dykes (311 +/- 17 Ma). In the Mont Blanc massif, calc-alkaline rhyolitic dykes were emplaced simultaneously (307 +/- 2 Ma) at shallow crustal levels, but they derive from deeper magma sources denoting enhanced mantellic activity. Recently identified tuffs and volcaniclastic layers embedded at different levels of the Salvan-Dorenaz stratigraphic record testify a 295 +3/-4 Ma old episode of highly explosive volcanism from distant volcanic centers, possibly located in the Aar-Gotthard massifs (Central Alps). Their zircon typology is highly heterogeneous. documenting wall-rock contamination of the melts and/or admixture of crustal sediments, whereas consistent subpopulations point to high-temperature magmas of deep-seated origin and alkaline affinity. The dated volcanic layers from the Salvan-Dorenaz basin set the beginning of the detrital sedimentation at 308 +/- 3 Ma and constrain the deposition of 1.5-1.7 km thick of elastic sediments within a time span of 10-15 Ma. These results infer minimum, long-term subsidence rates during basin evolution in the order of >0.1 mm/a, while in the surrounding basement units estimated exhumation rates are in the range of 1 mm/a. All dated rocks contain inherited zircon populations about 350, 450 or 600 Ma old.

High-pressure metamorphism in the Adula nappe - Guide to the excursion of the Swiss Society of Mineralogy and Petrology (September 29 - October 5, 1991)

1st day: Lithology and structure of the northern Adula nappe around Zervreila 2nd day: High-pressure rocks of the Suretta nappe, the middle Adula nappe and its Mesozoic cover - Eclogite near Innerferrara, Suretta nappe - Crossite-bearing prasinite from schistes lustres near Nufenen - Eclogites south of Hinterrhein, Adula nappe - Blueschists and eclogites from Neu-Wahli, Misox zone 3 days: Eclogite boudin and associated whiteschists in the uppermost Calanca valley, middle Adula nappe 4th day: Eclogites, associated metapelites and granitoid gneisses of Trescolmen, middle Adula nappe 5th day: The ultramafic-mafic suite of the Cima Lunga nappe around Cima di Gagnone 6th day: Garnet peridotites and eclogites from Alpe Arami, Cima Lunga nappe

Propagation of the Ignition Front against Airflow in Packed Beds of Wood Particles

Combustion of wood is increasing because of the needs of decreasing the emissions of carbon dioxide and the amount of waste going to landfills. Wood based fuels are often scattered on a large area. The transport distances should be short enough to prevent too high costs, and so the size of heating and power plants using wood fuels is often rather small. Combustion technologies of small-size units have to be developed to reach efficient and environmentally friendly energy production. Furnaces that use different packed bed combustion or gasification techniques areoften most economic in small-scale energy production. Ignition front propagation rate affects the stability, heat release rate and emissions of packed bed combustion. Ignition front propagation against airflow in packed beds of wood fuels has been studied. The research has been carried out mainly experimentally. Theoretical aspects have been considered to draw conclusions about the experimental results. The effects of airflow rate, moisture content of the fuel, size, shape and density of particles, and porosity of the bed on the propagation rate of the ignition front have been studied. The experiments were carried out in a pot furnace. The fuels used in the experiments were mainly real wood fuels that are often burned in the production of energy. The fuel types were thin wood chips, saw dust, shavings, wood chips, and pellets with different sizes. Also a few mixturesof the above were tested. Increase in the moisture content of the fuel decreases the propagation rates of the ignition front and makes the range of possible airflow rates narrower because of the energy needed for the evaporation of water and the dilution of volatile gases due to evaporated steam. Increase in the airflow rate increases the ignition rate until a maximum rate of propagation is reached after which it decreases. The maximum flame propagation rate is not always reached in stoichiometric combustion conditions. Increase in particle size and density transfers the optimum airflow rate towards fuel lean conditions. Mixing of small and large particles is often advantageous, because small particles make itpossible to reach the maximum ignition rate in fuel rich conditions, and large particles widen the range of possible airflow rates. A correlation was found forthe maximum rate of ignition front propagation in different wood fuels. According to the correlation, the maximum ignition mass flux is increased when the sphericity of the particles and the porosity of the bed are increased and the moisture content of the fuel is decreased. Another fit was found between sphericity and porosity. Increase in sphericity decreases the porosity of the bed. The reasons of the observed results are discussed.

Improvement of pyrolysis oil quality by scrubbing

Diplomityössä tutkittiin kuuman pyrolyysihöyryn puhdistamista haisevista ja kevyistä haihtuvista yhdisteistä. Työn kirjallisuusosassa selvitettiin pyrolyysiöljyn kannattavuutta uusiutuvana energialähteenä. Lisäksi eri pesurityyppejä tarkasteltiin ja ja vertailtiin. Työn kokeellisessa osassa käytettiin kahta erilaista koelaitteistoa. Tuotteen talteenotossa vertailtiin reaktorilämpötilan ja raaka-aineen kosteuden vaikutusta pyrolyysisaantoihin. Komponenttien talteenotossa tutkittiin epästabiilien ja pistävän hajuisten yhdisteiden poistamista kuumasta pyrolyysihöyrystä. Raaka-aineena käytettiin kuusen metsätäh-dehaketta, joka sisältää runsaasti neulasia ja kaarnaa. Kokeet toteutettiin lämpötila-alueella 460 - 520 °C. Koelaitteistot koostuivat kaasun (N2) syöttöjärjestelmään kytketystä kuumasta ja kyl-mästä puolesta. Tuotteen talteenotossa kuuma pyrolyysihöyry jäähdytettiin ja otettiin talteen. Komponenttien talteenotossa tuote kerättiin suodattimelle ja metyleeniklo-ridiloukkuun. Tuotteiden koostumukset analysoitiin kaasukromatokrafilla. Korkeimmat orgaaniset saannot saatiin 480 °C reaktorilämpötilalla ja 8-9 p-% raaka-ainekosteudella. Pyrolyysiveden määrä putosi raaka-aineen kosteutta nostettaessa. Eri reaktorilämpötiloilla ja raaka-ainekosteuksilla ei ollut vaikutusta hiiltosaantoihin. Kaasusaannot (pääosin CO2, CO ja hiilivedyt) olivat noin 10 p-%. Komponenttien talteenotossa suodatin tukkeutui matalissa (< 250 °C) lämpötiloissa. Suodattimelle jäänyt materiaali oli pääosin neulasista ja kaarnasta peräisin olevia uuteaineita (pääosin hartsi- rasvahappoja) ja sokereita. Korkeimmissa lämpötiloissa (> 250 °C) uuteaineet läpäisivät suodattimen paremmin. 250 ja 300 °C:n lämpötiloissa suuri määrä lyhytketjuisia helposti haihtuvia epästabiileja ja haisevia yhdisteitä (ketoneja, furaani- ja furfuraalijohdannaisia jne.) jäi metyleenikloridi- ja metanoliloukkuihin.

Diagnosis of endocrine disease: High-yield thyroid fine-needle aspiration cytology: an update focused on ancillary techniques improving its accuracy.

Thyroid fine-needle aspiration (FNA) cytology is a fast growing field. One of the most developing areas is represented by molecular tests applied to cytological material. Patients that could benefit the most from these tests are those that have been diagnosed as 'indeterminate' on FNA. They could be better stratified in terms of malignancy risk and thus oriented with more confidence to the appropriate management. Taking in to consideration the need to improve and keep high the yield of thyroid FNA, professionals from various fields (i.e. molecular biologists, endocrinologists, nuclear medicine physicians and radiologists) are refining and fine-tuning their diagnostic instruments. In particular, all these developments aim at increasing the negative predictive value of FNA to improve the selection of patients for diagnostic surgery. These advances involve terminology, the application of next-generation sequencing to thyroid FNA, the use of immunocyto- and histo-chemistry, the development of new sampling techniques and the increasing use of nuclear medicine as well as molecular imaging in the management of patients with a thyroid nodule. Herein, we review the recent advances in thyroid FNA cytology that could be of interest to the 'thyroid-care' community, with particular focus on the indeterminate diagnostic category.

The composition of airborne and grain-dust fungal communities is shaped at regional scale by plant genotypes and farming practices

Chronic exposure to airborne fungi has been associated with different respiratory symptoms and pathologies in occupational populations, such as grain workers. However, the homogeneity in the fungal species composition of these bioaerosols on a large geographical scale and the different drivers that shape these fungal communities remain unclear. In this study, the diversity of fungi in grain dust and in the aerosols released during harvesting was determined across 96 sites at a geographical scale of 560 km(2) along an elevation gradient of 500 m by tag-encoded 454-pyrosequencing of the internal transcribed spacer (ITS) sequences. Associations between the structure of fungal communities in the grain dust and different abiotic (farming system, soil characteristics, geographic and climatic parameters) and biotic (wheat cultivar, previous crop culture) factors were explored. These analyses revealed a strong relationship between the airborne and grain dust fungal communities and showed the presence of allergenic and mycotoxigenic species in most samples, which highlights the potential contribution of these fungal species to work-related respiratory symptoms of grain workers. The farming system was the major driver of the alpha and beta phylogenetic diversity of fungal communities. In addition, elevation and soil CaCO3 concentrations shaped the alpha diversity whereas wheat cultivar, cropping history and the number of freezing days per year shaped the taxonomic beta diversity of these communities.

A convenient method for the determination of moisture in aromatic plants

A method is proposed for the determination of the moisture content of aromatic plants. This method is based on the co-distillation of the starting material in a modified Clevenger apparatus with four organic solvents (toluene, cyclohexane, dichloromethane and carbon tetrachloride). The results were compared with those obtained by oven drying at 105 ºC and steam distillation of the essential oil. The efficiencies of the methods were shown to be equivalent. The solvent distillation method was more practical, especially with respect to operating time (2 h).