Microgeneration of electricity with producer gas in dual fuel mode operation

Among the alternatives to meet the increasing of world demand for energy, the use of biomass as energy source is one of the most promising as it contributes to reducing emissions of carbon dioxide in the atmosphere. Gasification is a technological process of biomass energy production of a gaseous biofuel. The fuel gas has a low calorific value that can be used in Diesel engine in dual mode for power generation in isolated communities. This study aimed to evaluate the reduction in the consumption of oil Diesel an engine generator, using gas from gasification of wood. The engine generator brand used was a BRANCO, with direct injection power of 7.36 kW (10 HP) coupled to an electric generator 5.5 kW. Diesel oil mixed with intake air was injected, as the oil was injected via an injector of the engine (dual mode). The fuel gas was produced in a downdraft gasifier. The engine generator was put on load system from 0.5 kW to 3.5 kW through a set of electrical resistances. Diesel oil consumption was measured with a precision scale. It was concluded that the engine converted to dual mode when using the gas for the gasification of wood decreased Diesel consumption by up to 57%.

Evaluation of the heating of broilers in shed by means of gas hoods and underfloor heating

This study was conducted to evaluate and compare the behavior of the heating inside poultry shed through gas hood and underfloor heating. The experiment was conducted in poultry shed belonging to the Federal Institute of Education, Science and Technology of Triângulo Mineiro Region, Uberlândia city – state of Minas Gerais (MG), Brazil. The dimensions of the shed are 24 meters long and 9.6 meters wide and with a ceiling height of 3.2 meters. The temperature was measured with an optical thermometer of Minipa brand, MT 350 model. It was used, to the analysis of temperature behavior, the public domain software FEMM 4.2, which uses finite elements techniques, with data collected from two lots. Underfloor heating is made using hot water flowing through a serpentine type system, which is installed below the bed; this hot water is from solar heaters. An energetic and economic assessment of the warming shed for raising chickens was realized. From the results obtained with the simulations, it may observe that the heating through the floor provides a more homogeneous distribution of temperature when compared with the hood heating. The flow of heat is upwards supplying, thus, the greatest need of heating of the bird, which is the pectoral part.

Motores de reacción modernos por turbinas de gas

This Bachelor’s thesis investigates the different types of jet engines used nowadays, their performance and applications. The thesis includes a general study of dynamics of fly, engine thermodynamics and contamination.

Corporate Social Responsibility in the Oil and Gas Industry: Environmental Management Systems as a Source of Sustainable Development

The environmental aspect of corporate social responsibility (CSR) expressed through the process of the EMS implementation in the oil and gas companies is identified as the main subject of this research. In the theoretical part, the basic attention is paid to justification of a link between CSR and environmental management. The achievement of sustainable competitive advantage as a result of environmental capital growth and inclusion of the socially responsible activities in the corporate strategy is another issue that is of special significance here. Besides, two basic forms of environmental management systems (environmental decision support systems and environmental information management systems) are explored and their role in effective stakeholder interaction is tackled. The most crucial benefits of EMS are also analyzed to underline its importance as a source of sustainable development. Further research is based on the survey of 51 sampled oil and gas companies (both publicly owned and state owned ones) originated from different countries all over the world and providing reports on sustainability issues in the open access. To analyze their approach to sustainable development, a specifically designed evaluation matrix with 37 indicators developed in accordance with the General Reporting Initiative (GRI) guidelines for non-financial reporting was prepared. Additionally, the quality of environmental information disclosure was measured on the basis of a quality – quantity matrix. According to results of research, oil and gas companies prefer implementing reactive measures to the costly and knowledge-intensive proactive techniques for elimination of the negative environmental impacts. Besides, it was identified that the environmental performance disclosure is mostly rather limited, so that the quality of non-financial reporting can be judged as quite insufficient. In spite of the fact that most of the oil and gas companies in the sample claim the EMS to be embedded currently in their structure, they often do not provide any details for the process of their implementation. As a potential for the further development of EMS, author mentions possible integration of their different forms in a single entity, extension of existing structure on the basis of consolidation of the structural and strategic precautions as well as development of a unified certification standard instead of several ones that exist today in order to enhance control on the EMS implementation.

Porous silicon optical filters in gas sensing applications

In this thesis, the gas sensing properties of porous silicon-based thin-film optical filters are explored. The effects of surface chemistry on the adsorption and desorption of various gases are studied in detail. Special emphasis is placed on investigating thermal carbonization as a stabilization method for optical sensing applications. Moreover, the possibility of utilizing the increased electrical conductivity of thermally carbonized porous silicon for implementing a multiparametric gas sensor, which would enable simultaneous monitoring of electrical and optical parameters, is investigated. In addition, different porous silicon-based optical filter-structures are prepared, and their properties in sensing applications are evaluated and compared. First and foremost, thermal carbonization is established as a viable method to stabilize porous silicon optical filters for chemical sensing applications. Furthermore, a multiparametric sensor, which can be used for increasing selectivity in gas sensing, is also demonstrated. Methods to improve spectral quality in multistopband mesoporous silicon rugate filters are studied, and structural effects to gas sorption kinetics are evaluated. Finally, the stability of thermally carbonized optical filters in basic environments is found to be superior in comparison to other surface chemistries currently available for porous silicon. The results presented in this thesis are of particular interest for developing novel reliable sensing systems based on porous silicon, e.g., label-free optical biosensors.

IT Investment Portfolio Management Over Joint Ventures: Case Study in a Multinational Oil & Gas Company

With information technology (IT) playing an increasing important role in driving the business, the value of IT investment is often challenged because not all of those investment decisions are made in a reasonable way or aligned with business strategies. IT investment portfolio management (PfM) is an effective way to prioritize and select the right IT projects to invest in, by taking all the project proposals into consideration as a whole, based on their business value, risks, costs, and interrelationships. There are different decision models to prioritise projects, and the Analytic Hierarchy Process (AHP) is one of the most commonly-used methods and is discussed in this master thesis. At the same time, there are IT projects on different levels for a multinational company, from global to local. For instance, many of them are probably proposed by joint ventures on local level. In the oil & gas industry, joint ventures are often formed especially in the area of the upstream (exploration & production). How to involve those projects into the IT investment PfM approach of the parent company is a challenge, because the parent company cannot make the decisions on its own. It needs to prioritize all projects in an adequate way, communicate with JVs and influence them. Also, different control levels on JVs need to be considered. This paper hence attempts to introduce a tailored approach of IT investment PfM for a multinational oil & gas company to address the issues around JVs.

Analysis and validation of space averaged drag model for numerical simulations of gas-solid flows in fluidized beds

This thesis presents an approach for formulating and validating a space averaged drag model for coarse mesh simulations of gas-solid flows in fluidized beds using the two-fluid model. Proper modeling for fluid dynamics is central in understanding any industrial multiphase flow. The gas-solid flows in fluidized beds are heterogeneous and usually simulated with the Eulerian description of phases. Such a description requires the usage of fine meshes and small time steps for the proper prediction of its hydrodynamics. Such constraint on the mesh and time step size results in a large number of control volumes and long computational times which are unaffordable for simulations of large scale fluidized beds. If proper closure models are not included, coarse mesh simulations for fluidized beds do not give reasonable results. The coarse mesh simulation fails to resolve the mesoscale structures and results in uniform solids concentration profiles. For a circulating fluidized bed riser, such predicted profiles result in a higher drag force between the gas and solid phase and also overestimated solids mass flux at the outlet. Thus, there is a need to formulate the closure correlations which can accurately predict the hydrodynamics using coarse meshes. This thesis uses the space averaging modeling approach in the formulation of closure models for coarse mesh simulations of the gas-solid flow in fluidized beds using Geldart group B particles. In the analysis of formulating the closure correlation for space averaged drag model, the main parameters for the modeling were found to be the averaging size, solid volume fraction, and distance from the wall. The closure model for the gas-solid drag force was formulated and validated for coarse mesh simulations of the riser, which showed the verification of this modeling approach. Coarse mesh simulations using the corrected drag model resulted in lowered values of solids mass flux. Such an approach is a promising tool in the formulation of appropriate closure models which can be used in coarse mesh simulations of large scale fluidized beds.

Veritas Oil Works

kuv., 8 x 16 cm

Veritas Oil Works

kuv., 8 x 16 cm

Validation of a 3D model for oxygen combustion in a circulating fluidized bed

In this thesis, a model called CFB3D is validated for oxygen combustion in circulating fluidized bed boiler. The first part of the work consists of literature review in which circulating fluidized bed and oxygen combustion technologies are studied. In addition, the modeling of circulating fluidized bed furnaces is discussed and currently available industrial scale three-dimensional furnace models are presented. The main features of CFB3D model are presented along with the theories and equations related to the model parameters used in this work. The second part of this work consists of the actual research and modeling work including measurements, model setup, and modeling results. The objectives of this thesis is to study how well CFB3D model works with oxygen combustion compared to air combustion in circulating fluidized bed boiler and what model parameters need to be adjusted when changing from air to oxygen combustion. The study is performed by modeling two air combustion cases and two oxygen combustion cases with comparable boiler loads. The cases are measured at Ciuden 30 MWth Flexi-Burn demonstration plant in April 2012. The modeled furnace temperatures match with the measurements as well in oxygen combustion cases as in air combustion cases but the modeled gas concentrations differ from the measurements clearly more in oxygen combustion cases. However, the same model parameters are optimal for both air and oxygen combustion cases. When the boiler load is changed, some combustion and heat transfer related model parameters need to be adjusted. To improve the accuracy of modeling results, better flow dynamics model should be developed in the CFB3D model. Additionally, more measurements are needed from the lower furnace to find the best model parameters for each case. The validation work needs to be continued in order to improve the modeling results and model predictability.

Technology park as an element of innovative infrastructure- its role in internationalization support.

The Thesis concentrates on two central terms – Technology park and the resource-based view of the organization. General attention is devoted to competencies and capabilities of organizations that operate in foreign environment. It is difficult to go abroad without any experience and support from local government, especially for small or medium company. Technology and Science parks are the main sources of competitive advantage for this kind of organizations. They provide a huge range of services as well as business consultations and financial support on different stages of companies’ development. The Thesis was made with the assistance of Technopolis Oy in Lappeenranta. During the research companies in Finland and Russia were interviewed. Based on empirical findings important capabilities for entering foreign market were identified and some recommendations for the Technology park were given.

Occurrence of parasitism by Dioctophyma renale in ring-tailed coatis (Nasua nasua) of the Tiete Ecological Park, São Paulo, Brazil

Dioctophymosis is a worldwide renal parasitosis caused by the Dioctophyma renale nematode, which results in progressive destruction of renal tissue. Aquatics annelids are considered the main intermediate hosts and the literature refers as permanent hosts of dogs, wild mammals and even humans. During procedures for population control of coatis (Nasua nasua) in the Ecological Park of Tietê (PET), was noticed the presence of parasitosis by D. renale. From 68 animals, males and females, young and adults, submitted to exploratory laparotomy, 51 were positive for the presence of worms, 9 were found only in the right kidney. In 10 cases, in addition to right kidney parasitism, worms were also observed in the abdominal cavity. In 24 cases D. renale was found only in the abdominal cavity and in 8 animals the right kidney was reduced to a small rigid structure. The study showed that the preferred site for parasitism of the worm, considered erratic, was the abdominal cavity in 66.66% of the cases.

The Role of Universities in the Triple Helix model of innovation management within the biotechnology industry, Case example: Turku Science Park Network

Biotechnology has been recognized as the key strategic technology for industrial growth. The industry is heavily dependent on basic research. Finland continues to rank in the top 10 of Europe's most innovative countries in terms of tax-policy, education system, infrastructure and the number of patents issued. Regardless of the excellent statistical results, the output of this innovativeness is below acceptable. Research on the issues hindering the output creation has already been done and the identifiable weaknesses in the Finland's National Innovation system are the non-existent growth of entrepreneurship and the missing internationalization. Finland is proven to have all the enablers of the innovation policy tools, but is lacking the incentives and rewards to push the enablers, such as knowledge and human capital, forward. Science Parks are the biggest operator in research institutes in the Finnish Science and Technology system. They exist with the purpose of speeding up the commercialization process of biotechnology innovations which usually include technological uncertainty, technical inexperience, business inexperience and high technology cost. Innovation management only internally is a rather historic approach, current trend drives towards open innovation model with strong triple helix linkages. The evident problems in the innovation management within the biotechnology industry are examined through a case study approach including analysis of the semi-structured interviews which included biotechnology and business expertise from Turku School of Economics. The results from the interviews supported the theoretical implications as well as conclusions derived from the pilot survey, which focused on the companies inside Turku Science Park network. One major issue that the Finland's National innovation system is struggling with is the fact that it is technology driven, not business pulled. Another problem is the university evaluation scale which focuses more on number of graduates and short-term factors, when it should put more emphasis on the cooperation success in the long-term, such as the triple helix connections with interaction and knowledge distribution. The results of this thesis indicated that there is indeed requirement for some structural changes in the Finland's National innovation system and innovation policy in order to generate successful biotechnology companies and innovation output. There is lack of joint output and scales of success, lack of people with experience, lack of language skills, lack of business knowledge and lack of growth companies.