Influence of grease rheology on thrust ball bearings friction torque

The friction torque and the operating temperatures in a thrust ball bearing were measured for seven different types of greases, including three biodegradable greases having low toxicity. These friction torque tests were performed using a modified Four-Ball machine. Rheological evaluations of the lubricating greases were made using a rheometer. Bleed oils were extracted from the greases and the dynamic viscosities were measured. In order to compare the performance of the lubricant greases in terms of friction, the grease characteristics were related to experimental results, showing that the interaction between thickener and base oil have strong influences in the bearing friction torque.

Experimental measuring procedure for the friction torque in rolling bearings

The reduction of the power loss generated in mechanical transmissions and the use of low friction biodegradable lubricants has been attracting considerable attention in recent times. Therefore, it is necessary to develop methods to test and evaluate the performance of such lubricants and compare them with conventional ones. In this sense, a Four-Ball Machine was modified allowing the test of rolling bearings. A 51107 thrust ball bearing was used to test two different greases and the corresponding base oils. Friction torque and operating temperatures were continuously monitored to quantify the power loss and the heat evacuation for each lubricant tested. Copyright © 2010 John Wiley & Sons, Ltd.

Friction and wear in thrust ball bearings lubricated with biodegradable greases

Thrust ball bearings lubricated with several different types of grease, including three biodegradable low-toxicity greases, were tested in a modified four-ball machine in order to evaluate the bearing friction torque. At the end of each test, grease samples were obtained and analysed through ferrography, allowing the quantification and evaluation of the bearing wear. In order to compare the grease performance in terms of friction and wear, a correlation between the grease characteristics (base oil, bleed oil, thickener structure, and rheological parameters) and the experimental results was established.

Fractional describing function of systems with Coulomb friction

This paper studies the describing function (DF) of systems constituted by a mass subjected to nonlinear friction. The friction force is decomposed into two components, namely, the viscous and the Coulomb friction. The system dynamics is analyzed in the DF perspective revealing a fractional-order behavior. The reliability of the DF method is evaluated through the signal harmonic contents.

Embalagens Flexíveis: estudo do processo de reticulação de adesivos e do coeficiente de atrito

A dissertação foi realizada em ambiente industrial, mais precisamente na empresa Monteiro, Ribas – Embalagens Flexíveis, S.A.. Esta empresa dedica-se à impressão e laminagem de filmes, assim como à confeção de sacos. Os seus produtos são direcionados na sua maioria para a indústria alimentar, exportando mais de 50% da sua produção, e dizem respeito a complexos (dois ou mais filmes unidos pela presença de um adesivo) que podem possuir impressão ou não. Estes complexos podem ser enviados para o cliente em bobina ou já em saco. Os objetivos propostos pela empresa diziam respeito a estudos relacionados com a força de laminagem dos complexos, com o coeficiente de atrito dos mesmos e com a identificação dos espetros dos componentes dos adesivos, assim como o estudo do processo de reticulação dos mesmos por espetrofotometria de Infravermelho. Relativamente aos resultados obtidos verificou-se que tanto a tinta como os metalizados influenciam negativamente a força de laminagem. Por sua vez o coeficiente de atrito é afetado por vários fatores. Através dos ensaios experimentais verificou-se que o adesivo, a tinta e o verniz mate favorecem o aumento do valor do COF. Além disso, nos complexos em que se utilizaram filmes de polietileno de maior espessura obtiveram-se valores de COF mais baixos, e no que diz respeito à temperatura e à tensão de enrolamento, verificou-se que valores mais elevados e muito baixos da primeira traduzem-se num aumento do valor do COF e uma tensão de enrolamento maior também tem o mesmo efeito. Relativamente ao tipo de filme impresso, substratos com maior energia superficial atraem mais o agente de deslizamento (slip). Por último, não se conseguiu perceber qual o tipo de adesivo (com ou sem solvente) que tem maior impacto no COF uma vez que em 55% dos casos o valor do COF é superior nas amostras que foram complexadas com adesivo sem solvente e em 45% o COF era superior nas amostras complexadas com adesivo base solvente. No que diz respeito aos espetros obtidos verificou-se que a reticulação dos adesivos é identificada pela diminuição da extensão do pico correspondente à ligação N=C=O.

Encodage des forces tactiles dans le cortex somatosensoriel primaire

Les deux fonctions principales de la main sont la manipulation d’objet et l’exploration tactile. La détection du glissement, rapportée par les mécanorécepteurs de la peau glabre, est essentielle pour l’exécution de ces deux fonctions. Durant la manipulation d’objet, la détection rapide du micro-glissement (incipient slip) amène la main à augmenter la force de pince pour éviter que l’objet ne tombe. À l’opposé, le glissement est un aspect essentiel à l’exploration tactile puisqu’il favorise une plus grande acuité tactile. Pour ces deux actions, les forces normale et tangentielle exercées sur la peau permettent de décrire le glissement mais également ce qui arrive juste avant qu’il y ait glissement. Toutefois, on ignore comment ces forces contrôlées par le sujet pourraient être encodées au niveau cortical. C’est pourquoi nous avons enregistré l’activité unitaire des neurones du cortex somatosensoriel primaire (S1) durant l’exécution de deux tâches haptiques chez les primates. Dans la première tâche, deux singes devaient saisir une pastille de métal fixe et y exercer des forces de cisaillement sans glissement dans une de quatre directions orthogonales. Des 144 neurones enregistrés, 111 (77%) étaient modulés à la direction de la force de cisaillement. L’ensemble de ces vecteurs préférés s’étendait dans toutes les directions avec un arc variant de 50° à 170°. Plus de 21 de ces neurones (19%) étaient également modulés à l’intensité de la force de cisaillement. Bien que 66 neurones (59%) montraient clairement une réponse à adaptation lente et 45 autres (41%) une réponse à adaptation rapide, cette classification ne semblait pas expliquer la modulation à l’intensité et à la direction de la force de cisaillement. Ces résultats montrent que les neurones de S1 encodent simultanément la direction et l’intensité des forces même en l’absence de glissement. Dans la seconde tâche, deux singes ont parcouru différentes surfaces avec le bout des doigts à la recherche d’une cible tactile, sans feedback visuel. Durant l’exploration, les singes, comme les humains, contrôlaient les forces et la vitesse de leurs doigts dans une plage de valeurs réduite. Les surfaces à haut coefficient de friction offraient une plus grande résistance tangentielle à la peau et amenaient les singes à alléger la force de contact, normale à la peau. Par conséquent, la somme scalaire des composantes normale et tangentielle demeurait constante entre les surfaces. Ces observations démontrent que les singes contrôlent les forces normale et tangentielle qu’ils appliquent durant l’exploration tactile. Celles-ci sont également ajustées selon les propriétés de surfaces telles que la texture et la friction. Des 230 neurones enregistrés durant la tâche d’exploration tactile, 96 (42%) ont montré une fréquence de décharge instantanée reliée aux forces exercées par les doigts sur la surface. De ces neurones, 52 (54%) étaient modulés avec la force normale ou la force tangentielle bien que l’autre composante orthogonale avait peu ou pas d’influence sur la fréquence de décharge. Une autre sous-population de 44 (46%) neurones répondait au ratio entre la force normale et la force tangentielle indépendamment de l’intensité. Plus précisément, 29 (30%) neurones augmentaient et 15 (16%) autres diminuaient leur fréquence de décharge en relation avec ce ratio. Par ailleurs, environ la moitié de tous les neurones (112) étaient significativement modulés à la direction de la force tangentielle. De ces neurones, 59 (53%) répondaient à la fois à la direction et à l’intensité des forces. L’exploration de trois ou quatre différentes surfaces a permis d’évaluer l’impact du coefficient de friction sur la modulation de 102 neurones de S1. En fait, 17 (17%) neurones ont montré une augmentation de leur fréquence de décharge avec l’augmentation du coefficient de friction alors que 8 (8%) autres ont montré le comportement inverse. Par contre, 37 (36%) neurones présentaient une décharge maximale sur une surface en particulier, sans relation linéaire avec le coefficient de friction des surfaces. La classification d’adaptation rapide ou lente des neurones de S1 n’a pu être mise en relation avec la modulation aux forces et à la friction. Ces résultats montrent que la fréquence de décharge des neurones de S1 encode l’intensité des forces normale et tangentielle, le ratio entre les deux composantes et la direction du mouvement. Ces résultats montrent que le comportement d’une importante sous-population des neurones de S1 est déterminé par les forces normale et tangentielle sur la peau. La modulation aux forces présentée ici fait le pont entre les travaux évaluant les propriétés de surfaces telles que la rugosité et les études touchant à la manipulation d’objets. Ce système de référence s’applique en présence ou en absence de glissement entre la peau et la surface. Nos résultats quant à la modulation des neurones à adaptation rapide ou lente nous amènent à suggérer que cette classification découle de la manière que la peau est stimulée. Nous discuterons aussi de la possibilité que l’activité des neurones de S1 puisse inclure une composante motrice durant ces tâches sensorimotrices. Finalement, un nouveau cadre de référence tridimensionnel sera proposé pour décrire et rassembler, dans un même continuum, les différentes modulations aux forces normale et tangentielle observées dans S1 durant l’exploration tactile.

Indigenous knowledges and power in friction with human rights and development discourses : the case of the Witoto Ethnic Safeguarding Plan in the Colombian Amazon

Cette thèse analyse les négociations interculturelles des Gens du Centre (groupe amazonien multi-ethnique) avec les discours universels de droits humains et de développement mobilisés par l’État colombien. L’analyse se concentre sur le Plan de sauvegarde ethnique Witoto chapitre Leticia (ESP), qui est un des 73 plans formulés et implémentés par l’État colombien pour reconnaître les droits des peuples autochtones en danger par le déplacement forcé causé par les conflits armés internes. J’analyse l’ESP à travers la notion de friction (Tsing, 2005) qui fait référence aux caractéristiques complexes, inégalitaires et changeantes des rencontres contemporaines entre les différences des savoirs locaux et globaux. Mon analyse se base aussi sur des approches foucaldiennes et/ou subalternes de pouvoir comme la recherche anticoloniale et de la décolonisation, les perspectives critiques et contre-hégémoniques des droits humains, le post-développement, et les critiques du féminisme au développement. L’objectif de la thèse est d’analyser les savoirs (concepts de loi, de justice et de développement); les logiques de pensée (pratiques, épistémologies, rôles et espaces pour partager et produire des savoirs); et les relations de pouvoir (formes de leadership, associations, réseaux, et formes d’empowerment et disempowerment) produits et recréés par les Gens du Centre au sein des frictions avec les discours de droits humains et du développement. La thèse introduit comment la région habitée par les Gens du Centre (le Milieu Amazone transfrontalier) a été historiquement connectée aux relations inégalitaires de pouvoir qui influencent les luttes actuelles de ce groupe autochtone pour la reconnaissance de leurs droits à travers l’ESP. L’analyse se base à la fois sur une recherche documentaire et sur deux terrains ethnographiques, réalisés selon une perspective critique et autoréflexive. Ma réflexion méthodologique explore comment la position des chercheurs sur le terrain influence le savoir ethnographique et peut contribuer à la création des relations interculturelles inclusives, flexibles et connectées aux besoins des groupes locaux. La section analytique se concentre sur comment le pouvoir circule simultanément à travers des échelles nationale, régionale et locale dans l’ESP. J’y analyse comment ces formes de pouvoir produisent des sujets individuels et collectifs et s’articulent à des savoirs globaux ou locaux pour donner lieu à de nouvelles formes d’exclusion ou d’émancipation des autochtones déplacés. Les résultats de la recherche suggèrent que les Gens du Centre approchent le discours des droits humains à travers leurs savoirs autochtones sur la « loi de l’origine ». Cette loi établit leur différence culturelle comme étant à la base du processus de reconnaissance de leurs droits comme peuple déplacé. D’ailleurs, les Gens du Centre approprient les discours et les projets de développement à travers la notion d’abondance qui, comprise comme une habileté collective qui connecte la spiritualité, les valeurs culturelles, et les rôles de genre, contribue à assurer l’existence physique et culturelle des groupes autochtones. Ma thèse soutient que, même si ces savoirs et logiques de pensée autochtones sont liés à des inégalités et à formes de pouvoir local, ils peuvent contribuer à des pratiques de droits humains et de développement plurielles, égalitaires et inclusives.

Dynamic characteristics of Atmospheric boundary Layer during different phases of Monsoon

Atmospheric Boundary layer (ABL) is the layer just above the earth surface and is influenced by the surface forcing within a short period of an hour or less. In this thesis, characteristics of the boundary layer over ocean, coastal and inland areas of the atmosphere, especially over the monsoon regime are thoroughly studied. The study of the coastal zone is important due to its high vulnerability mainly due to sea breeze circulation and associated changes in the atmospheric boundary layer. The major scientific problems addressed in this thesis are diurnal and seasonal variation of coastal meteorological properties, the characteristic difference in the ABL during active and weak monsoons, features of ABL over marine environment and the variation of the boundary layer structure over an inland station. The thesis describes the various features in the ABL associated with the active and weak monsoons and, the surface boundary layer properties associated with the active and weak epochs. The study provides knowledge on MABL and can be used as the estimated values of boundary layer parameters over the marine atmosphere and to know the values and variabilities of the ABL parameters such as surface wind, surface friction, drag coefficient, wind stress and wind stress curl.

Salting coefficient of hydroxybenzoic acids

The Setschenow parameter and thermodynamic parameters of transfer of 2- and 4- hydroxybenzoic acids from water to salt solutions have been reported. The data have been rationalised by considering the structure breaking effects of the ions of the salts, the localized hydrolysis model, the internal pressure theory and the theory of water structure due to Symons.

Mathematical Modelling of the Dynamics of Granular Materials in a Rotating Cylinder

The current study is aimed at the development of a theoretical simulation tool based on Discrete Element Method (DEM) to 'interpret granular dynamics of solid bed in the cross section of the horizontal rotating cylinder at the microscopic level and subsequently apply this model to establish the transition behaviour, mixing and segregation.The simulation of the granular motion developed in this work is based on solving Newton's equation of motion for each particle in the granular bed subjected to the collisional forces, external forces and boundary forces. At every instant of time, the forces are tracked and the positions velocities and accelarations of each partcle is The software code for this simulation is written in VISUAL FORTRAN 90 After checking the validity of the code with special tests, it is used to investigate the transition behaviour of granular solids motion in the cross section of a rotating cylinder for various rotational speeds and fill fraction.This work is hence directed towards a theoretical investigation based on Discrete Element Method (DEM) of the motion of granular solids in the radial direction of the horizontal cylinder to elucidate the relationship between the operating parameters of the rotating cylinder geometry and physical properties ofthe granular solid.The operating parameters of the rotating cylinder include the various rotational velocities of the cylinder and volumetric fill. The physical properties of the granular solids include particle sizes, densities, stiffness coefficients, and coefficient of friction Further the work highlights the fundamental basis for the important phenomena of the system namely; (i) the different modes of solids motion observed in a transverse crosssection of the rotating cylinder for various rotational speeds, (ii) the radial mixing of the granular solid in terms of active layer depth (iii) rate coefficient of mixing as well as the transition behaviour in terms of the bed turnover time and rotational speed and (iv) the segregation mechanisms resulting from differences in the size and density of particles.The transition behaviour involving its six different modes of motion of the granular solid bed is quantified in terms of Froude number and the results obtained are validated with experimental and theoretical results reported in the literature The transition from slumping to rolling mode is quantified using the bed turnover time and a linear relationship is established between the bed turn over time and the inverse of the rotational speed of the cylinder as predicted by Davidson et al. [2000]. The effect of the rotational speed, fill fraction and coefficient of friction on the dynamic angle of repose are presented and discussed. The variation of active layer depth with respect to fill fraction and rotational speed have been investigated. The results obtained through simulation are compared with the experimental results reported by Van Puyvelde et. at. [2000] and Ding et at. [2002].The theoretical model has been further extended, to study the rmxmg and segregation in the transverse direction for different particle sizes and their size ratios. The effect of fill fraction and rotational speed on the transverse mixing behaviour is presented in the form of a mixing index and mixing kinetics curve. The segregation pattern obtained by the simulation of the granular solid bed with respect to the rotational speed of the cylinder is presented both in graphical and numerical forms. The segregation behaviour of the granular solid bed with respect to particle size, density and volume fraction of particle size has been investigated. Several important macro parameters characterising segregation such as mixing index, percolation index and segregation index have been derived from the simulation tool based on first principles developed in this work.

Utilisation of Coir Geotextiles for Unpaved Roads and Embankments

The increasing tempo of construction activity the world over creates heavy pressure on existing land space. The quest for new and competent site often points to the needs for improving existing sites, which are otherwise deemed unsuitable for adopting conventional foundations. This is accomplished by ground improvement methods, which are employed to improve the quality of soil incompetent in their natural state. Among the construction activities, a well-connected road network is one of the basic infrastructure requirements, which play a vital role for the fast and comfortable movement of inter- regional traffic in countries like India.One of the innovative ground improvement techniques practised all over the world is the use of geosynthetics, which include geotextiles, geomembranes, geogrids, etc . They offer the advantages such as space saving, enviromnental sensitivity, material availability, technical superiority, higher cost savings, less construction time, etc . Because of its fundamental properties, such as tensile strength, filtering and water permeability, a geotextile inserted between the base material and sub grade can function as reinforcement, a filter medium, a separation layer and as a drainage medium. Though polymeric geotextiles are used in abundant quantities, the use of natural geotextiles (like coir, jute, etc.) has yet to get momentum. This is primarily due to the lack of research work on natural geotextilcs for ground improvement, particularly in the areas of un paved roads. Coir geotextiles are best suited for low cost applications because of its availability at low prices compared to its synthetic counterparts. The proper utilisation of coir geotextilcs in various applications demands large quantities of the product, which in turn can create a boom in the coir industry. The present study aims at exploring the possibilities of utilising coir geotextiles for unpaved roads and embankments.The properties of coir geotextiles used have been evaluated. The properties studied include mass per unit area, puncture resistance, tensile strength, secant modulus, etc . The interfacial friction between soils and three types of coir geotextiles used was also evaluated. It was found that though the parameters evaluated for coir geotextiles have low values compared to polymeric geotextiles, the former are sufficient for use in unpaved roads and embankments. The frictional characteristics of coir geotextile - soil interfaces are extremely good and satisfy the condition set by the International Geosynthetic Society for varied applications.The performance of coir geotextiles reinforced subgrade was studied by conducting California Bearing Ratio (CBR) tests. Studies were made with coir geotextiles placed at different levels and also in multiple layers. The results have shown that the coir geotextile enhances the subgrade strength. A regression analysis was perfonned and a mathematical model was developed to predict the CBR of the coir geotextile reinforced subgrade soil as a function of the soil properties, coir geotextile properties, and placement depth of reinforcement.The effects of coir geotextiles on bearing capacity were studied by perfonning plate load tests in a test tan1e This helped to understand the functioning of geotextile as reinforcement in unpaved roads and embankments. The perfonnance of different types of coir geotextiles with respect to the placement depth in dry and saturated conditions was studied. The results revealed that the bearing capacity of coir-reinforced soil is increasing irrespective of the type of coir geotextiles and saturation condition.The rut behaviour of unreinforced and coir reinforced unpaved road sections were compared by conducting model static load tests in a test tank and also under repetitive loads in a wheel track test facility. The results showed that coir geotextiles could fulfill the functions as reinforcement and as a separator, both under static and repetitive loads. The rut depth was very much reduced whik placing coir geotextiles in between sub grade and sub base.In order to study the use of Coir geotextiles in improving the settlement characteristics, two types of prefabricated COlf geotextile vertical drains were developed and their time - settlement behaviour were studied. Three different dispositions were tried. It was found that the coir geotextile drains were very effective in reducing consolidation time due to radial drainage. The circular drains in triangular disposition gave maximum beneficial effect.In long run, the degradation of coir geotextile is expected, which results in a soil - fibre matrix. Hence, studies pertaining to strength and compressibility characteristics of soil - coir fibre composites were conducted. Experiments were done using coir fibres having different aspect ratios and in different proportions. The results revealed that the strength of the soil was increased by 150% to 200% when mixed with 2% of fibre having approximately 12mm length, at all compaction conditions. Also, the coefficient of consolidation increased and compression index decreased with the addition of coir fibre.Typical design charts were prepared for the design of coir geotextile reinforced unpaved roads. Some illustrative examples are also given. The results demonstrated that a considerable saving in subase / base thickness can he achieved with the use of eoir geotextiles, which in turn, would save large quantities of natural aggregates.

Malayalam Isolated Digit Recognition using HMM and PLP cepstral coefficient

Development of Malayalam speech recognition system is in its infancy stage; although many works have been done in other Indian languages. In this paper we present the first work on speaker independent Malayalam isolated speech recognizer based on PLP (Perceptual Linear Predictive) Cepstral Coefficient and Hidden Markov Model (HMM). The performance of the developed system has been evaluated with different number of states of HMM (Hidden Markov Model). The system is trained with 21 male and female speakers in the age group ranging from 19 to 41 years. The system obtained an accuracy of 99.5% with the unseen data

Influence of Interface Surface Geometries In The Tensile Characteristics Of Friction Welded Joints From Aluminium Alloys

Friction welding is a solid state joining process that produces coalescence in materials, using the heat developed between surfaces through a combination of mechanical induced rubbing motion and applied load. In rotary friction welding technique heat is generated by the conversion of mechanical energy into thermal energy at the interface of the work pieces during rotation under pressure. Traditionally friction welding is carried out on a dedicated machine because of its adaptability to mass production. In the present work, steps were made to modify a conventional lathe to rotary friction welding set up to obtain friction welding with different interface surface geometries at two different speeds and to carry out tensile characteristic studies. The surface geometries welded include flat-flat, flat-tapered, tapered-tapered, concave-convex and convex-convex. A comparison of maximum load, breaking load and percentage elongation of different welded geometries has been realized through this project. The maximum load and breaking load were found to be highest for weld formed between rotating flat and stationary tapered at 500RPM and the values were 19.219kN and 14.28 kN respectively. The percentage elongation was found to be highest for weld formed between rotating flat and stationary flat at 500RPM and the value was 21.4%. Hence from the studies it is cleared that process parameter like “interfacing surface geometries” of weld specimens have strong influence on tensile characteristics of friction welded joints

A Comparative Study Of Tensile And Microstructural Characteristics Of Friction Welded Joints And Conventionally Welded Joints Of Aluminium Alloy 6061

Welding of high strength and low weight materials like Aluminium Alloys without any defects by conventional welding techniques is a major challenge in industries. Hence research on solid state welding techniques like Friction stir welding and Friction welding techniques have got much importance in joining of Aluminium alloys. However most of the industries are not changing conventional techniques as skilled workers are available on that area. Most common conventional welding techniques used for joining of Aluminium alloys are Gas welding and Arc welding. Friction welding is a solid-state welding process that generates heat through mechanical friction between a moving and a stationary component with the addition of a lateral force called “upset” to plast ically displace and fuse the materials. In this work, experimental study on tensile and micro structural characteristics of welded joints formed from conventional welding techniques and Rotary friction welding(suitable for weld specimens with circular cross section) has been carried out and the same were compared. The process parameters for arc welding used was 50-70 Amp reverse polarity DC and electrodes of 2.3mm diameter. In Gas welding, the parameters were oxy acetylene neural flame at 3200°C and 3mm electrodes . In the case of friction welding an axial pressure loading of 3Mpa with 5 MPa as upsetting pressure and 500 rpm were used to obtain good welded joints. Tensile characteristic studies of Arc welded joints and Gas welded joints showed 48% and 60 % variations respectively from the maximum load bearing characteristics of parent metal. In the case of friction welded joint, the variation was found to 46%. Micro structural evaluation of conventionally welded joints exhibited clear distinct zones of various weld regions. In the case of friction welded joint micro structural photographs showed comparable features both in parent metal and welded region. Thus the tensile characteristic study and microstructure evaluations proved that friction welded joints are good in both aspects compared to conventionally welded joints.