How to promote and enhance communication between a big retailer's after-sales department and its suppliers

W is the biggest electronic goods retailer in Portugal accounting with almost fifty percent of market share in its area. During the last years, many small W suppliers had to close their doors, and many others are in huge troubles. Among the reason for this situation, the huge bargaining power of W in the relationship seems crucial. The focus of the directed research will be in the after sales department where I did an internship from September 2014 to January 2015.

Optimisation and design of post-tensioning anchorage corner blisters in concrete box girder bidges

The design of anchorage blisters of internal continuity post-tensioning tendons of bridges built by the cantilever method, presents some peculiarities, not only because they are intermediate anchorages but also because these anchorages are located in blisters, so the prestressing force has to be transferred from the blister the bottom slab and web of the girder. The high density of steel reinforcement in anchorage blisters is the most common reason for problems with concrete cast in situ, resulting in zones with low concrete compacity, leading to concrete crushing failures under the anchor plates. A solution may involve improving the concrete compression and tensile strength. To meet these requirements a high-performance fibre reinforced self-compacting mix- ture (HPFRC) was used in anchorage corner blisters of post-tensioning tendons, reducing the concrete cross-section and decreasing the reinforcement needed. To assess the ultimate capacity and the adequate serviceability of the local anchorage zone after reducing the minimum concrete cross-section and the confining reinforcement, specified by the anchorage device supplier for the particular tendon, load transfer tests were performed. To investigate the behaviour of anchorage blisters regarding the transmission of stresses to the web and the bottom slab of the girder, and the feasibility of using high performance concrete only in the blister, two half scale models of the inferior corner of a box girder existing bridge were studied: a reference specimen of ordinary reinforced concrete and a HPFRC blister specimen. The design of the reinforcement was based in the tensile forces obtained on strut-and-tie models. An experimental program was carried out to assess the models used in design and to study the feasibility of using high performance concrete only in the blister, either with casting in situ, or with precast solutions. A non-linear finite element analysis of the tested specimens was also performed and the results compared.

Hormone replacement therapy and the risk of breast cancer: assessment of therapy acceptance in a cohort of previously treated breast cancer patients

INTRODUCTION: In the postmenopausal period, an average of 25% of women will present symptomatic ovarian failure requiring hormonal replacement therapy. Estrogen can relieve vasomotor symptoms. Hormonal replacement therapy is generally not recommended for breast cancer patients due to the potential risk of tumor recurrence. To answer the questions about the safety of hormonal replacement therapy in this subgroup of women, it is necessary to establish the acceptance of treatment. METHODS: Between September 1998 and February 2001, a cohort of 216 breast cancer patients were asked to complete a questionnaire. All patients had completed their treatment and were informed about survival rates after breast cancer and hormonal replacement therapy. RESULTS: Among the 216 patients, 134 (62%) would refuse hormonal replacement therapy. A hundred patients were afraid of relapse (74.6%). Adjuvant tamoxifen therapy was the only statistically significant variable (70.3% versus 29.7% p=0.003). Understanding clinical stage (p= 0.045) and type of medical assistance (private versus public , p=0.033) also seemed to influence the decision. Early stage disease (p= 0.22), type of surgical procedure (radical versus conservative, p=0.67), adjuvant chemotherapy (p=0.082) or marital status (p=0.98 ) were not statistically significant in decision making. Several patients submitted to adjuvant chemotherapy (41.6%) would accept hormonal replacement therapy under medical supervision, as did most of advanced clinical stage patients (58.3%; p=0.022). CONCLUSION: There is a high level of rejection for hormonal replacement therapy among breast cancer patients when current data on tumor cure rates, and potential risks of estrogen use is available. Adverse effects of tamoxifen in the adjuvant setting may be the reason for refusal of hormonal replacement therapy .

In Search of the Origins of Modernism: Venice and the Crisis of Classical Architecture in the mid-eighteenth century

This paper attempts to prove that in the years 1735 to 1755 Venice was the birthplace and cradle of Modern architectural theory, generating a major crisis in classical architecture traditionally based on the Vitruvian assumption that it imitates early wooden structures in stone or in marble. According to its rationalist critics such as the Venetian Observant Franciscan friar and architectural theorist Carlo Lodoli (1690-1761) and his nineteenth-century followers, classical architecture is singularly deceptive and not true to the nature of materials, in other words, dishonest and fallacious. This questioning did not emanate from practising architects, but from Lodoli himself– a philosopher and educator of the Venetian patriciate – who had not been trained as an architect. The roots of this crisis lay in a new approach to architecture stemming from the new rationalist philosophy of the Enlightenment age with its emphasis on reason and universal criticism.

How to improve urban mobility in Lisbon: intermodality and information and ticketing systems

Urban mobility is one of the main challenges facing urban areas due to the growing population and to traffic congestion, resulting in environmental pressures. The pathway to urban sustainable mobility involves strengthening of intermodal mobility. The integrated use of different transport modes is getting more and more important and intermodality has been mentioned as a way for public transport compete with private cars. The aim of the current dissertation is to define a set of strategies to improve urban mobility in Lisbon and by consequence reduce the environmental impacts of transports. In order to do that several intermodal practices over Europe were analysed and the transport systems of Brussels and Lisbon were studied and compared, giving special attention to intermodal systems. In the case study was gathered data from both cities in the field, by using and observing the different transport modes, and two surveys were done to the cities users. As concluded by the study, Brussels and Lisbon present significant differences. In Brussels the measures to promote intermodality are evident, while in Lisbon a lot still needs to be done. It also made clear the necessity for improvements in Lisbon’s public transports to a more intermodal passenger transport system, through integration of different transport modes and better information and ticketing system. Some of the points requiring developments are: interchanges’ waiting areas; integration of bicycle in public transport; information about correspondences with other transport modes; real-time information to passengers pre-trip and on-trip, especially in buses and trams. After the identification of the best practices in Brussels and the weaknesses in Lisbon the possibility of applying some of the practices in Brussels to Lisbon was evaluated. Brussels demonstrated to be a good example of intermodality and for that reason some of the recommendations to improve intermodal mobility in Lisbon can follow the practices in place in Brussels.

Production of mexican brown macroalgae fucoidan and fucosidases under an integral green technology bioproceses by the biorefinery concept

Marine ecosystem can be considered a rather exploited source of natural substances with enormous bioactive potential. In Mexico macro-algae study remain forgotten for research and economic purposes besides the high amount of this resource along the west and east coast. For that reason the Bioferinery Group of the Autonomous University of Coahuila, have been studying the biorefinery concept in order to recover high value byproducts of Mexican brown macro-algae including polysaccharides and enzymes to be applied in food, pharmaceutical and energy industry. Brown macroalgae are an important source of fucoidan, alginate and laminarin which comprise a complex group of macromolecules with a wide range of important biological properties such as anticoagulant, antioxidant, antitumoral and antiviral and also as rich source of fermentable sugars for enzymes production. Additionally, specific enzymes able to degrade algae matrix (fucosidases, sulfatases, aliginases, etc) are important tools to establish structural characteristics and biological functions of these polysaccharides. The aims of the present work were the integral study of bioprocess for macroalgae biomass exploitation by the use of green technologies as hydrothermal extraction and solid state fermentation in order to produce polysaccharides and enzymes (fucoidan and fucoidan hydrolytic enzymes). This work comprises the use of the different bioprocess phases in order to produce high value products with lower time and wastes.

Experimental analysis of the cyclic response of traditional timber joints and their influence on the seismic capacity of timber frame structures

Timber connections represent the crucial part of a timber structure and a great variability exists in terms of types of connections and mechanisms. Taking as case study the widespread traditional timber frame structures, in particular the Portuguese Pombalino buildings, one of the most common timber connection is the half-lap joint. Connections play a major role in the overall behaviour of a structure, particularly when assessing their seismic response, since damage is concentrated at the connections. For this reason, an experimental campaign was designed and distinct types of tests were carried out on traditional half-lap joints to assess their in-plane response. In particular, pull-out and in-plane cyclic tests were carried out on real scale unreinforced connections. Subsequently, the connections were retrofitted, using strengthening techniques such as self-tapping screws, steel plates and GFRP sheets. The tests chosen were meant to capture the hysteretic behaviour and dissipative capacity of the connections and characterise their response and, therefore, their influence on the seismic response of timber frame walls, particularly concerning their uplifting and rotation capacity, that could lead to rocking in the walls. In this paper, the results of the experimental campaign are presented in terms of hysteretic curves, dissipated energy and equivalent viscous damping ratio. Moreover, recommendations are provided on the most appropriate retrofitting solutions.

Contribution of portuguese vernacular building strategies to indoor thermal comfort and occupants’ perception

Solar passive strategies that have been developed in vernacular architecture from different regions are a response to specific climate effects. These strategies are usually simple, low-tech and have low potential environmental impact. For this reason, several studies highlight them as having potential to reduce the demands of non-renewable energy for buildings operation. In this paper, the climatic contrast between northern and southern parts of mainland Portugal is presented, namely the regions of Beira Alta and Alentejo. Additionally, it discusses the contribution of different climate-responsive strategies developed in vernacular architecture from both regions to assure thermal comfort conditions. In Beira Alta, the use of glazed balconies as a strategy to capture solar gains is usual, while in Alentejo the focus is on passive cooling strategies. To understand the effectiveness of these strategies, thermal performances and comfort conditions of two case studies were evaluated based on the adaptive comfort model. Field tests included measurement of hygrothermal parameters and surveys on occupants’ thermal sensation. From the results, it has been found that the case studies have shown a good thermal performance by passive means alone and that the occupants feel comfortable, except during winter where there is the need to use simple heating systems.

Gender norms in Portuguese college sudents' judgments in familial homicides: bad men and mad women

The gender of the offender has been proved to be an important factor in judicial sentencing. In this study, we analyze the judgments of College students regarding perpetrators of familial homicides to evaluate the presence of these gender norms and biases in the larger society. The sample included 303 college students (54.8% female) enrolled in several social sciences and engineering courses. Participants were asked to read 12 vignettes based on real crimes taken from Portuguese newspapers. Half were related to infanticide, and half were related to intimate partner homicide. The sex of the offender was orthogonally manipulated to the type of crime. The results show that gender had an important impact on sentences, with males being more harshly penalized by reasons of perversity and women less penalized by reason of mental disorders. In addition, filicide was more heavily penalized than was intimate partner homicide. The results also revealed a tendency toward a retributive conception of punishment. We discuss how gender norms in justice seem to be embedded in society as well as the need for intervention against the punitive tendency of this population.

Flowering levels, harvest season and yields of cupuassu (Theobroma grandiflorum)

Cupuassu (Theobroma grandiflorum), a specie native to Amazonia, has been planted commercially in Brazil to satisfy the demand for the flavorful juice obtained from the pulp around its seeds. The trees are notorious for low and irregular fruit production. Data gathered over two seasons from trees in a germplasm collection in Pará, Brazil, showed that some of them fruited more regularly than others. Differences in fruit production correlated to differences in flower production. Tree-to-tree variation in flower production, fruit production, and consistency of both over time suggest considerable scope for improving yields by selection. Hand pollinations resulted in a much higher frequency of fruit set than open pollinations, indicating that lack of effective pollination is also a reason for low yield. However, attempts to increase the level of effective pollination are handicapped by low knowledge about the pollinators of cupuassu and their behavior.

Girls out of school. State, culture and education in poor rural Lao People's Democratic Republic

Tese de Doutoramento em Sociologia

Upgrade of an industrial building: BIM model of the as-built situation and evaluation of modifications

Dissertação de mestrado integrado in Civil Engineering

Fundamental studies on natural deep eutectic solvents: physico-chemical, thermal and rheological properties

When combined at particular molar fractions, sugars, aminoacids or organic acids a present a high melting point depression, becoming liquids at room temperature. These are called Natural Deep Eutectic Solvents – NADES and are envisaged to play a major role on the chemical engineering processes of the future. Nonetheless, there is a significant lack of knowledge of its fundamental and basic properties, which is hindering their industrial applications. For this reason it is important to extend the knowledge on these systems, boosting their application development [1]. In this work, we have developed and characterized NADES based on choline chloride, organic acids, amino acids and sugars. Their density, thermal behavior, conductivity and polarity were assessed for different compositions. The conductivity was measured from 0 to 40 °C and the temperature effect was well described by the Vogel-Fulcher-Tammann equation. The morphological characterization of the crystallizable materials was done by polarized optical microscopy that provided also evidence of homogeneity/phase separation. Additionally, the rheological and thermodynamic properties of the NADES and the effect of water content were also studied. The results show these systems have Newtonian behavior and present significant viscosity decrease with temperature and water content, due to increase on the molecular mobility. The anhydrous systems present viscosities that range from higher than 1000Pa.s at 20°C to less than 1Pa.s at 70°C. DSC characterization confirms that for water content as high as 1:1:1 molar ratio, the mixture retains its single phase behavior. The results obtained demonstrate that the NADES properties can be finely tunned by careful selection of its constituents. NADES present the necessary properties for use as extraction solvents. They can be prepared from inexpensive raw materials and tailored for the selective extraction of target molecules. The data produced in this work is hereafter importance for the selection of the most promising candidates avoiding a time consuming and expensive trial and error phase providing also data for the development of models able to predict their properties and the mechanisms that allow the formation of the deep eutectic mixtures.

In vitro digestion and stability assessment of b-lactoglobulin/riboflavin nanostructures

B-Lactoglobulin (b-Lg) is the major protein fraction of bovine whey serum and a primary gelling agent. b-Lg has a high nutritional value, is stable at low pH being highly resistant to proteolytic degradation in the stomach, besides, it has the ability of acting as an encapsulating agent. This study aims at assessing the ability of b-Lg nanostructures to associate a nutraceutical - i.e. riboflavin - and release it in a controlled manner throughout an in vitro gastrointestinal (GI) system. For this reason b-Lg nanostructures loaded with riboflavin were critically characterized in terms of their morphology (i.e. size, polydispersity, -potential and shape) by dynamic light scattering (DLS) and transmission electron microscopy (TEM), and efficiency to associate to riboflavin through spectrofluorimetry. Furthermore, these nanocomplexes were evaluated in an in vitro GI model, simulating the physiological conditions. Stable b-Lg nanostructures were obtained at pH 6, of spherical shape, characterized by particle size of 172±1 nm, low polydispersity (i.e. PDI of 0.06±0.02), -potential of -32±3 mV and association efficiency (AE) of 26±1 %. b-Lg nanostructures showed to be stable upon their passage throughout stomach (i.e. particle size, PDI and potential of 248±10 nm, 0.18±0.03 and 18±3 mV, respectively). Concerning their passage throughout the intestine, such nanostructures were mostly degraded in the duodenum. Regarding riboflavin, a release of about 11 % was observed after their passage through stomach, while 35 %, 38 % and 5 % were the released percentages of the total riboflavin associated observed after passage through duodenum, jejunum and ileum, respectively. Hence,b-Lg nanostructures showed to be suitable carriers for riboflavin until the intestine, where their degradation occurs. b-Lg also showed to be structurally stable, under food simulant conditions (yoghurt simulant, composed of 3 % acetic acid), over 14 days, with a protective effect upon riboflavin activity, releasing it in a 7 day period.

Current situation on the occurrence of mycotoxins and toxigenic fungi in Portugal

Mycotoxins are secondary metabolites produced by filamentous fungi that are toxic for humans and animals in small amounts and that are found worldwide in a large number of agricultural commodities. They are usually ingested involuntarily, when contaminated plant products are consumed, and represent a great risk for public health. Therefore, governments throughout the world have imposed strict legal limits for their levels in food and feed products in order to reduce potential health risks for consumers. Despite of its ubiquity, the mycotoxin problem is mainly dependent on regional factors, such as the mycotoxigenic characteristics of the local mycoflora, the local climate conditions, and the local agricultural practices. For this reason, a constant vigilance from local governmental food safety agencies and from the local researcher community is needed. This communication will review the current situation on the occurrence of mycotoxigenic fungi in some Portuguese cultures, such as wine grapes, corn and dried fruits. Particular attention will be given to the incidence of mycotoxigenic Aspergillus strains in those cultures and to the levels of ochratoxin A, aflatoxins, cyclopiazonic acid and fumonisin B2 produced. Data will be discussed taking into account the geographical origin of the isolates and the particular climate conditions of each sampling region. An updated review on the levels of the main mycotoxins found in local products and in imported commodities will also be presented.