Electrical characterization of poly(amide-imide) for application in organic field effect devices

The admittance spectra and current-voltage (I-V) characteristics are reported of metal-insulator-metal (MIM) and metal-insulator-semiconductor (MIS) capacitors employing cross-linked poly(amide-imide) (c-PAI) as the insulator and poly(3-hexylthiophene) (P3HT) as the active semiconductor. The capacitance of the MIM devices are constant in the frequency range from 10 Hz to 100 kHz, with tan delta values as low as 7 x 10(-3) over most of the range. Except at the lowest voltages, the I-V characteristics are well-described by the Schottky equation for thermal emission of electrons from the electrodes into the insulator. The admittance spectra of the MIS devices displayed a classic Maxwell-Wagner frequency response from which the transverse bulk hole mobility was estimated to be similar to 2 x 10(-5) cm(2) V(-1)s(-1) or similar to 5 x 10(-8) cm(2) V(-1)s(-1) depending on whether or not the surface of the insulator had been treated with hexamethyldisilazane (HMDS) prior to deposition of the P3HT. From the maximum loss observed in admittance-voltage plots, the interface trap density was estimated to be similar to 5 x 10(10) cm(-2) eV(-1) or similar to 9 x 10(10) cm(-2) eV(-1) again depending whether or not the insulator was treated with HMDS. We conclude, therefore, that HMDS plays a useful role in promoting order in the P3HT film as well as reducing the density of interface trap states. Although interposing the P3HT layer between the insulator and the gold electrode degrades the insulating properties of the c-PAI, nevertheless, they remain sufficiently good for use in organic electronic devices. (c) 2012 Elsevier B.V. All rights reserved.

Densification and enhancement of the grain boundary conductivity of gadolinium-doped barium cerate by ultra fast flash grain welding

Doped barium cerate is a promising solid electrolyte for intermediate temperature fuel cells as a protonic conductor. However, it is difficult to sinter it to high density at a reasonable temperature. Moreover, it presents a high grain boundary resistivity at intermediate temperatures. Flash grain welding was applied to compacted samples, starting from a temperature of 910 degrees C and applying, for a short time, an ac electric polarization of 40 V, 1000 Hz. At that frequency, the resulting current flows through the grain boundaries promoting a welding via a local Joule heating. A large decrease of the grain boundary resistivity was observed by impedance spectroscopy. Scanning electron microscopy observations of polished and etched surfaces revealed highly sintered regions. Attempts were also made to combine flash grain welding with conventional sintering. (C) 2012 Elsevier Ltd. All rights reserved.

Ion-Conducting Membranes Based on Gelatin and Containing LiI/I-2 for Electrochromic Devices

Ionic conducting membranes of gelatin plasticized with glycerol and containing LiI/I-2 have been obtained and characterized by X-ray diffraction measurements, UV-Vis-NIR spectroscopy, thermal analysis and impedance spectroscopy. The transparent (80-90% in the visible range) membranes showed ionic conductivity value of 5 x 10(-5) S/cm at room temperature, which increased to 3 x 10(-3) S/cm at 80 degrees C. All the ionic conductivity measurements as a function of temperature showed VTF dependence and activation energy of 8 kJ/mol. These samples also showed low glass transition temperature of -76 degrees C. Moreover the samples were predominantly amorphous. The membranes applied to small electrochromic devices showed 20% of color change from colored to bleached states during more than 70 cronoamperometric cycles.

Effects of chemical composition on the corrosion of dental alloys

The aim of this study was to determine the effect of the oral environment on the corrosion of dental alloys with different compositions, using electrochemical methods. The corrosion rates were obtained from the current-potential curves and electrochemical impedance spectroscopy (EIS). The effect of artificial saliva on the corrosion of dental alloys was dependent on alloy composition. Dissolution of the ions occurred in all tested dental alloys and the results were strongly dependent on the general alloy composition. Regarding the alloys containing nickel, the Ni-Cr and Ni-Cr-Ti alloys released 0.62 mg/L of Ni on average, while the Co-Cr dental alloy released ions between 0.01 and 0.03 mg/L of Co and Cr, respectively.The open-circuit potential stabilized at a higher level with lower deviation (standard deviation: Ni-Cr-6Ti = 32 mV/SCE and Co-Cr = 54 mV/SCE). The potenciodynamic curves of the dental alloys showed that the Ni-based dental alloy with >70 wt% of Ni had a similar curve and the Co-Cr dental alloy showed a low current density and hence a high resistance to corrosion compared with the Ni-based dental alloys. Some changes in microstructure were observed and this fact influenced the corrosion behavior for the alloys. The lower corrosion resistance also led to greater release of nickel ions to the medium. The quantity of Co ions released from the Co-Cr-Mo alloy was relatively small in the solutions. In addition, the quantity of Cr ions released into the artificial saliva from the Co-Cr alloy was lower than Cr release from the Ni-based dental alloys.

Layer-by-Layer assembled cobalt ferrite nanoparticles for chemical sensing

Ultra-thin (thicknesses of 50-90 nm) nanocomposite films of cobalt ferrite nanoparticles (np-CoFe2O4, 18 nm in diameter) and polyelectrolytes (doped polyaniline-PANI, poly-3,4-ethylenedioxy thiophene: polystyrene sulfonic acid-PEDOT:PSS, and sulfonated lignin-SL) are assembled layer-by-layer onto interdigitated microelectrodes aiming at to create novel nanostructured sensoactive materials for liquid media chemical sensors. The nanocomposites display a distinctive globular morphology with nanoparticles densely-packed while surrounded by polyelectrolytes. Due to the presence of np-CoFe2O4 the nanocomposites display low electrical conductivity according to impedance data. On the other hand, this apparent shortcoming turns such nanocomposites much more sensitive to the presence of ions in solution than films made exclusively of conducting polyelectrolytes. For example, the electrical resistance of np-CoFe2O4/PEDOT:PSS and PANI/SL/np-CoFe2O4/SL architectures has a 10-fold decrease when they are immersed in 20 mmol. L-1 NaCl solution. Impedance spectra fitted with the response of an equivalent circuit model suggest that the interface created between nanoparticles and polyelectrolytes plays a major role on the nanocomposites electrical/dielectrical behavior. Since charge transport is sensitive to nanoparticle-polyelectrolyte interfaces as well as to the physicochemical conditions of the environment, the np-CoFe2O4-based nanocomposites can be used as sensing elements in chemical sensors operated under ac regime and room temperature.

Dielectric properties of cobalt ferrite nanoparticles in ultrathin nanocomposite films

Multilayered nanocomposite films (thickness 50-90 nm) of cobalt ferrite nanoparticles (np-CoFe2O4, 18 nm) were deposited on top of interdigitated microelectrodes by the layer-by-layer technique in order to study their dielectric properties. For that purpose, two different types of nanocomposite films were prepared by assembling np-CoFe2O4 either with poly(3,4-ethylenedioxy thiophene):poly(styrene sulfonic acid) or with polyaniline and sulfonated lignin. Despite the different film architectures, the morphology of both was dominated by densely-packed layers of nanoparticles surrounded by polyelectrolytes. The dominant effect of np-CoFe2O4 was also observed after impedance spectroscopy measurements, which revealed that dielectric behavior of the nanocomposites was largely influenced by the charge transport across nanoparticle-polyelectrolyte interfaces. For example, nanocomposites containing np-CoFe2O4 exhibited a single low-frequency relaxation process, with time constants exceeding 15 ms. At 1 kHz, the dielectric constant and the dissipation factor (tan ᵟ) of these nanocomposites were 15 and 0.15, respectively. These values are substantially inferior to those reported for pressed pellets made exclusively of similar nanoparticles. Impedance data were further fitted with equivalent circuit models from which individual contributions of particle's bulk and interfaces to the charge transport within the nanocomposites could be evaluated. The present study evidences that such nanocomposites display a dielectric behavior dissimilar from that exhibited by their individual counterparts much likely due to enlarged nanoparticle- polyelectrolyte interfaces.

On the degradation mechanisms under the influence of pedological factors through the study of archeological bronze patina

This experimental thesis concerns the study of the long-term behaviour of ancient bronzes recently excavated from burial conditions. The scientific interest is to clarify the effect of soil parameters on the degradation mechanisms of ancient bronze alloy. The work took into consideration bronzes recovered from the archaeological sites in the region of Dobrudja, Romania. The first part of research work was dedicated to the characterization of bronze artefacts using non destructive (micro-FTIR, reflectance mode) and micro-destructive (based on sampling and analysis of a stratigraphical section by OM and SEM-EDX) methods. Burial soils were geologically classified and analyzed by chemical methods (pH, conductivity, anions content). Most of objects analyzed showed a coarse and inhomogeneous corroded structure, often made up of several corrosion layers. This has been explained by the silt nature of soils, which contain low amount of clay and are, therefore, quite accessible to water and air. The main cause of a high dissolution rate of bronze alloys is the alternate water saturation and instauration of the soil, for example on a seasonal scale. Moreover, due to the vicinity of the Black Sea, the detrimental effect of chlorine has been evidenced for few objects, which were affected by the bronze disease. A general classification of corrosion layers was achieved by comparing values of the ratio Cu/Sn in the alloy and in the patina. Decuprification is a general trend, and enrichment of copper within the corrosion layers, due to the formation of thick layers of cuprite (Cu2O), is pointed out as well. Uncommon corrosion products and degradation patterns were presented as well, and they are probably due to peculiar local conditions taking place during the burial time, such as anaerobic conditions or fluctuating environmental conditions. In order to acquire a better insight into the corrosion mechanisms, the second part of the thesis has regarded simulation experiments, which were conducted on commercial Cu-Sn alloys, whose composition resembles those of ancient artefacts one. Electrochemical measurements were conducted in natural electrolytes, such as solutions extracted from natural soil (sampled at the archaeological sites) and seawater. Cyclic potentiodynamic experiments allowed appreciating the mechanism of corrosion in both cases. Soil extract’s electrolyte has been evaluated being a non aggressive medium, while artificial solution prepared by increasing the concentration of anions caused the pitting corrosion of the alloy, which is demonstrated by optical observations. In particular, electrochemical impedance spectroscopy allows assessing qualitatively the nature of corroded structures formed in soil and seawater. A double-structured layer is proposed, which differ, in the two cases, for the nature of the internal passive layer, which result defectiveness and porous in case of seawater.

Festkörperunterstützte Lipid-Modellmembranen auf Gold zur Rekonstitution von Membranproteinen

Festkörperunterstützte Lipid-Modellmembranen auf Goldzur Rekonstitution von Membranproteinen Ziel der Arbeit war der Aufbau von Lipid-Modellmembranen auf Goldelektroden in welchen die funktionelle Aktivität von rekonstituierten Membranproteinen über elektrochemische Methoden nachgewiesen werden kann.Im Rahmen der Arbeit wurden Lipidbilayer mit und ohne hydrophile Ethylenglykol-Spacer durch Kombination von Selbstorganisation, Langmuir-Blodgett-Kuhn-Techniken und Vesikelfusion aufgebaut. Dabei dienten Thiolipide zur Verankerung der Membranen auf der Goldelektrode und es wurden diverse Wege verfolgt, deren Ankerdichte auf dem Substrat einzustellen.Eine Studie zum Aufbau von festkörperunterstützten Lipidbilayern durch Fusion von Vesikeln auf binäre Alkanthiol-/Hydroxythiol-Monolagen mit definierter Oberflächenenergie zeigte, daß eine minimale Grenzflächenenergie (Monolayer/Wasser) existiert, unterhalb welcher die Fusion nicht mehr zu einer zusätzlichen Monolage, sondern lediglich zur Ausbildung von adsorbierten oder teilgespreiteten Vesikeln führt.Zur Charakterisierung der Membranen wurden Oberflächenplasmonenresonanz, Impedanzspektroskopie, zyklische Voltammetrie, elektrochemische reduktive Desorption, Rasterkraftmikroskopie und Kontaktwinkelmessungen herangezogen.In die Modellmembranen wurden Membranproteine (Porin, Annexin V, H+-ATPase) sowie ganze Membranfragmente (Bande 3 aus roten Blutzellen) rekonstituiert und mittels elektrochemischer Methoden auf ihre funktionelle Aktivität überprüft.

Cellulose based Lithium ion polymer electrolytes for Lithium batteries

The separator membrane in batteries and fuel cells is of crucial importance for the function of these devices. In lithium ion batteries the separator membrane as well as the polymer matrix of the electrodes consists of polymer electrolytes which are lithium ion conductors. To overcome the disadvantage of currently used polymer electrolytes which are highly swollen with liquids and thus mechanically and electrochemically unstable, the goal of this work is a new generation of solid polymer electrolytes with a rigid backbone and a soft side chain structure. Moreover the novel material should be based on cheap substrates and its synthesis should not be complicated aiming at low overall costs. The new materials are based on hydroxypropylcellulose and oligoethyleneoxide derivatives as starting materials. The grafting of the oligoethyleneoxide side chains onto the cellulose was carried out following two synthetic methods. One is based on a bromide derivative and another based on p-toluolsulfonyl as a leaving group. The side chain reagents were prepared form tri(ethylene glycol) monoethyl ether. In order to improve the mechanical properties the materials were crosslinked. Two different conceptions have been engaged based on either urethane chemistry or photosensitive dimethyl-maleinimide derivatives. PEO - graft - cellulose derivatives with a high degree of substitution between 2,9 and 3,0 were blended with lithium trifluoromethane-sulfonate, lithium bis(trifluorosulfone)imide and lithium tetrafluoroborate. The molar ratios were in the range from 0,02 to 0,2 [Li]/[O]. The products have been characterized with nuclear magnetic resonance (NMR), gel permeation chromatography (GPC) and laserlight scattering (LS) with respect to their degree of substitution and molecular weight. The effect of salt concentration on ionic conductivity, thermal behaviour and morphology has been investiga-ted with impedance spectroscopy, differential scanning calorimetry (DSC) and thermal gravimetric analysis (TGA). The crosslinking reactions were controlled with dynamic mechanical analysis (DMS). The degree of substitution of our products is varying between 2,8 and 3,0 as determined by NMR. PEO - graft - cellulose derivatives are highly viscous liquids at room temperature with glass transition temperatures around 215 K. The glass transition temperature for the Lithium salt complexes of PEO - graft - cellulose deri-vatives increase with increasing salt content. The maximum conductivity at room temperature is about 10-4 and at 100°C around 10-3 Scm-1. The presence of lithium salt decreases the thermal stability of the complexes in comparison to pure PEO - graft - cellulose derivatives. Complexes heated over 140 – 150°C completely lose their ionic conductivity. The temperature dependence of the conductivity presented as Arrhenius-type plots for all samples is similar in shape and follows a VTF behaviour. This proofs that the ionic transport is closely related to the segmental motions of the polymer chains. Novel cellulose derivatives with grafted oligoethylen-oxide side chains with well-defined chemical structure and high side chain grafting density have been synthesized. Cellulose was chosen as stiff, rod like macromolecule for the backbone while oligoethylen-oxides are chosen as flexible side chains. A maximum grafting density of 3.0 have been obtained. The best conductivity reaches 10-3 Scm-1 at 100°C for a Li-triflate salt complex with a [Li]/[O] ratio of 0.8. The cross-linked complexes containing the lithium salts form elastomeric films with convenient mechanical stability. Our method of cellulose modification is based on relatively cheap and commercially available substrates and as such appears to be a promising alternative for industrial applications.

Assembly and characterization of supramolecular architectures for biosensor applications

The research has included the efforts in designing, assembling and structurally and functionally characterizing supramolecular biofunctional architectures for optical biosensing applications. In the first part of the study, a class of interfaces based on the biotin-NeutrAvidin binding matrix for the quantitative control of enzyme surface coverage and activity was developed. Genetically modified ß-lactamase was chosen as a model enzyme and attached to five different types of NeutrAvidin-functionalized chip surfaces through a biotinylated spacer. All matrices are suitable for achieving a controlled enzyme surface density. Data obtained by SPR are in excellent agreement with those derived from optical waveguide measurements. Among the various protein-binding strategies investigated in this study, it was found that stiffness and order between alkanethiol-based SAMs and PEGylated surfaces are very important. Matrix D based on a Nb2O5 coating showed a satisfactory regeneration possibility. The surface-immobilized enzymes were found to be stable and sufficiently active enough for a catalytic activity assay. Many factors, such as the steric crowding effect of surface-attached enzymes, the electrostatic interaction between the negatively charged substrate (Nitrocefin) and the polycationic PLL-g-PEG/PEG-Biotin polymer, mass transport effect, and enzyme orientation, are shown to influence the kinetic parameters of catalytic analysis. Furthermore, a home-built Surface Plasmon Resonance Spectrometer of SPR and a commercial miniature Fiber Optic Absorbance Spectrometer (FOAS), served as a combination set-up for affinity and catalytic biosensor, respectively. The parallel measurements offer the opportunity of on-line activity detection of surface attached enzymes. The immobilized enzyme does not have to be in contact with the catalytic biosensor. The SPR chip can easily be cleaned and used for recycling. Additionally, with regard to the application of FOAS, the integrated SPR technique allows for the quantitative control of the surface density of the enzyme, which is highly relevant for the enzymatic activity. Finally, the miniaturized portable FOAS devices can easily be combined as an add-on device with many other in situ interfacial detection techniques, such as optical waveguide lightmode spectroscopy (OWLS), the quartz crystal microbalance (QCM) measurements, or impedance spectroscopy (IS). Surface plasmon field-enhanced fluorescence spectroscopy (SPFS) allows for an absolute determination of intrinsic rate constants describing the true parameters that control interfacial hybridization. Thus it also allows for a study of the difference of the surface coupling influences between OMCVD gold particles and planar metal films presented in the second part. The multilayer growth process was found to proceed similarly to the way it occurs on planar metal substrates. In contrast to planar bulk metal surfaces, metal colloids exhibit a narrow UV-vis absorption band. This absorption band is observed if the incident photon frequency is resonant with the collective oscillation of the conduction electrons and is known as the localized surface plasmon resonance (LSPR). LSPR excitation results in extremely large molar extinction coefficients, which are due to a combination of both absorption and scattering. When considering metal-enhanced fluorescence we expect the absorption to cause quenching and the scattering to cause enhancement. Our further study will focus on the developing of a detection platform with larger gold particles, which will display a dominant scattering component and enhance the fluorescence signal. Furthermore, the results of sequence-specific detection of DNA hybridization based on OMCVD gold particles provide an excellent application potential for this kind of cheap, simple, and mild preparation protocol applied in this gold fabrication method. In the final chapter, SPFS was used for the in-depth characterizations of the conformational changes of commercial carboxymethyl dextran (CMD) substrate induced by pH and ionic strength variations were studied using surface plasmon resonance spectroscopy. The pH response of CMD is due to the changes in the electrostatics of the system between its protonated and deprotonated forms, while the ionic strength response is attributed from the charge screening effect of the cations that shield the charge of the carboxyl groups and prevent an efficient electrostatic repulsion. Additional studies were performed using SPFS with the aim of fluorophore labeling the carboxymethyl groups. CMD matrices showed typical pH and ionic strength responses, such as high pH and low ionic strength swelling. Furthermore, the effects of the surface charge and the crosslink density of the CMD matrix on the extent of stimuli responses were investigated. The swelling/collapse ratio decreased with decreasing surface concentration of the carboxyl groups and increasing crosslink density. The study of the CMD responses to external and internal variables will provide valuable background information for practical applications.

New synthetic strategies to tethered bilayer lipid membranes

Tethered bilayer lipid membranes provide an efficient, stable and versatile platform for the investigation of integrated membrane proteins. However, the incorporation of large proteins, as well as of proteins with a large submembrane part is still a very critical issue and therefore, further optimisation of the system is necessary. The central element of a tBLM is a lipid bilayer. Its proximal leaflet is, at least to some extend, covalently attached to a solid support via a spacer group. The anchor lipid consists of three distinct parts, a lipid headgroup, a spacer group and an anchor. All parts together influence the final bilayer properties. In the frame of this work, the synthesis of new thiolipids for tBLMs on gold has been investigated. The aim was to obtain molecules with longer spacers in order to increase the submembrane space. The systems obtained have been characterized using SPR and EIS. The results obtained during this study are multiple. First, the synthesis of a previously synthesized architecture was successfully scaled up in an industrial lab using a new synthetic approach. The synthesis of large amounts is now feasible. Then, the synthesis of the new thiolipids was carried out taking into account the following requirements: the increase of the submembrane space by having longer ethyleneglycol spacers, the attachment of the molecules to a gold substrate via a thiol bond, and the tunability of the lateral mobility by changing the lipid headgroup. Three different synthetic strategies have been investigated. The polymeric approach did not prove to be successful, merely because of the broad molecular weight distribution. The synthesis of heterofunctionally protected oligoethyleneglycols allowed to obtain ethyleneglycol moieties with 6 and 8 units, but the tedious purification steps gave very low yields. Finally, the block by block synthesis using ethyleneglycol precursors proved to be an efficient and fast method to synthesize the target molecules. Indeed, these were obtained with very high yields, and the separation was very efficient. A whole family of new compounds was obtained, having 6, 8 and 14 ethyleneglycol units and with mono- or diphytanyl lipid headgroups. This new pathway is a very promising synthetic strategy that can be used further in the development of new compounds of the tether system. The formation of bilayers was investigated for the different thiolipids mainly by using EIS. The electrical properties of a bilayer define the quality of the membrane and allow the study of the functionality of proteins embedded in such a system. Despite multiple trials to improve the system using self assembly, Langmuir Blodgett transfer, and detergent mixed vesicles, the new polymer thiolipids did not show as high electrical properties as tBLMs reported in the literature. Nevertheless, it was possible to show that a bilayer could be obtained for the different spacer lengths. These bilayers could be formed using self assembly for the first monolayer, and two different methods for bilayer formation, namely vesicle fusion and solvent exchange. We could furthermore show functional incorporation of the ion carrier valinomycin: the selective transport of K+ ions could be demonstrated. For DPHL, it was even possible to show the functional incorporation of the ion channel gramicidin. The influence of the spacer length is translated into an increase of the spacer capacitance, which could correspond to an increase in the capacity of charge accumulation in the submembrane space. The different systems need to be further optimised to improve the electrical properties of the bilayer. Moreover, the incorporation of larger proteins, and proteins bearing submembrane parts needs to be investigated.

Photofixierung von Lipidmembranen aus Glykolipopolymeren auf Goldoberflächen

Ziel war Herstellung und Charakterisierung festkörperunterstützter Membransysteme aus Glykolipopolymeren auf Goldoberflächen, mit elektrischen Eigenschaften, die denen der Schwarzfilmmembranen entsprechen. Um diese Eigenschaften mit impedanzspektroskopischen Techniken messen zu können, ist die Präparation der Membranen auf Goldfilmen notwendig. Eine direkte Verankerung der Glykolipopolymermoleküle (GLP) auf der Goldoberfläche ist nicht möglich, daher werden die untersuchten GLP mit Hilfe von photoreaktiven Molekülen kovalent auf der Goldoberfläche immobilisiert. Untersuchten Abstandhalter waren Thio-Polyethylenglykol und eine Mischung zweier Alkanthiole, bestehend aus 1-Thiohexanol und Bis-(Aminododecyl)-disulfid. Thio-PEG-Monoschichten zeigten sehr unterschiedliche Schichtdicken, weil die Moleküle auf der Oberfläche sehr unterschiedliche Konformationen annehmen können, die eine regelmässige Anordnung erschweren. Langmuir-Blodgett Übertrag sowie die durchgeführte photochemische Fixierung der GLP-Moleküle auf Thio-PEG Schichten führte zu Eigenschaften, die auf den Aufbau einer Lipidmonolage hinweisen. Diese stellte jedoch im Bereich der Lipidmoleküle keine geschlossene Schicht dar. Es kommen als Abstandhaltermoleküle für die Photofunktionalisierung nur Moleküle in Frage, die aufgrund ihrer Eigenschaften eine regelmässige Anordnung auf der Goldoberfläche anstreben. Diese Voraussetzung erfüllt am besten die Gruppe der Alkanthiole. Terminal funktionalisierte Alkanthiole müssen jedoch mit nicht oder anderweitig funktionalisierten Alkanthiolen verdünnt assembliert werden, um weitergehende Funktionalisierungen einzugehen. Die untersuchten GLP lassen sich aufgrund ihrer amphiphilen Struktur an der Wasser-Luft Grenzfläche vororientieren. In allen Fällen gelingt auch der Langmuir-Blodgett Übertrag der komprimierten Schicht, sowie, nach der für die Anbindung notwendigen Trocknung, die photochemisch kovalente Fixierung der Monoschicht durch Bestrahlung mit UV-Licht. Damit konnte erstmals die photochemisch kovalente Fixierung von GLPs auf der Goldoberfläche gezeigt werden. Untersuchungen erfolgten an einem Copolymer sowie zwei unterschiedlichen Homopolymermolekülen. Der unterschiedliche molekulare Aufbau der GLP spiegelt sich in ihrem Verhalten an der Wasser-Luft Grenzfläche sowie in den Eigenschaften der gebildeten Monoschichten wieder. Die Copolymer-Schichten zeigten sehr unterschiedliche Schichtdicken. Auch die EIS-Daten sind schlecht reproduzierbar. Dies ist auf die molekulare Struktur des Copolymers zurückzuführen. Gänzlich unterschiedlich verhalten sich die Homopolymere. Aufgrund ihrer Struktur lassen sie sich zu dichten Schichten komprimieren. Messungen der Fluoreszenzerholung nach Photobleichung (FRAP) zeigen homogene aber nicht fluide Schichten. Die photochemisch kovalente Fixierung des Moleküls auf der Goldoberfläche konnte durch SPR- sowie EIS-Messungen nachgewiesen werden. Die EIS-Messungen zeigen Werte, die sich in Bereichen der idealen Modellmembran bewegen. Der erfolgreiche Einbau von Valinomycin konnte bestätigt werden. FRAP Untersuchungen zeigten die Bildung homogener Schichten. Diese sind jedoch im Bereich der proximalen Lipidschicht nicht fluide. Um die Fluidität in Anlehnung an die Eigenschaften der natürlichen Membranen zu erhöhen, wurden die photochemisch kovalent fixierten Anker-Glykolipopolymer-Moleküle durch Mischung mit freien Lipiden lateral verdünnt. Auch die kovalente Fixierung der GLP-Bausteine innerhalb gemischten Schichten konnte erfolgreich demonstriert werden. Die Schichten zeigten sich jedoch, mit Ausnahme der Schichten aus 50mol% Homopolymer und 50mol% Lipid, inhomogen. Nach Photobleichung durch den Laserblitz kam es nur bei den 50mol%:50mol% -Schichten (Ho: Lipid) zur Erholung der Fluoreszenz, was auf das Vorliegen von beweglichen Lipidmolekülen innerhalb der Membran schliessen lässt. Der Versuch der Inkorporation von Valinomycin gelang ebenfalls. Alle genannten Ergebnisse deuten darauf hin, dass die molekulare Architektur der hergestellten Schichten durch die unterschiedlichen Längendimensionen des Homopolymer-Moleküls einerseits, sowie des Lipids andererseits nicht für alle Mischungsverhältnisse ausreichend stabil ist. Die für die kovalente Fixierung erforderliche Trocknung der Schicht führt zu einer deutlichen Verminderung des Wassergehaltes des Systems und einer daraus resultierenden starken Destabilisierung der aufgebauten Schichten. Insgesamt gesehen stellt somit die photochemische Fixierung der glykosidischen Homopolymer-Membranen ein vielversprechendes Modellsystem dar.

Advanced CMOS Interfaces for Bio-Nanosensors

The improvement of devices provided by Nanotechnology has put forward new classes of sensors, called bio-nanosensors, which are very promising for the detection of biochemical molecules in a large variety of applications. Their use in lab-on-a-chip could gives rise to new opportunities in many fields, from health-care and bio-warfare to environmental and high-throughput screening for pharmaceutical industry. Bio-nanosensors have great advantages in terms of cost, performance, and parallelization. Indeed, they require very low quantities of reagents and improve the overall signal-to-noise-ratio due to increase of binding signal variations vs. area and reduction of stray capacitances. Additionally, they give rise to new challenges, such as the need to design high-performance low-noise integrated electronic interfaces. This thesis is related to the design of high-performance advanced CMOS interfaces for electrochemical bio-nanosensors. The main focus of the thesis is: 1) critical analysis of noise in sensing interfaces, 2) devising new techniques for noise reduction in discrete-time approaches, 3) developing new architectures for low-noise, low-power sensing interfaces. The manuscript reports a multi-project activity focusing on low-noise design and presents two developed integrated circuits (ICs) as examples of advanced CMOS interfaces for bio-nanosensors. The first project concerns low-noise current-sensing interface for DC and transient measurements of electrophysiological signals. The focus of this research activity is on the noise optimization of the electronic interface. A new noise reduction technique has been developed so as to realize an integrated CMOS interfaces with performance comparable with state-of-the-art instrumentations. The second project intends to realize a stand-alone, high-accuracy electrochemical impedance spectroscopy interface. The system is tailored for conductivity-temperature-depth sensors in environmental applications, as well as for bio-nanosensors. It is based on a band-pass delta-sigma technique and combines low-noise performance with low-power requirements.

Ion channels in mixed tethered bilayer lipid membranes

Mixed tethered bilayer lipid membranes (tBLMs) are described based on the self-assembly of a monolayer on template stripped gold, of an archea analogue thiolipid, 2,3-di-o-phytanyl-sn-glycerol-1-tetraethylene glycol-D,L--lipoic acid ester lipid (DPTL), and a newly designed dilution molecule, tetraethylene glycol-D,L--lipoic acid ester (TEGL). The usage of spacer and addition of extra dilution molecules between the substrate and the bilayer is that this architecture provides an ionic reservoir underneath the membrane, avoiding direct contact of the embedded membrane proteins with the gold electrodes and increasing the lateral diffusion of the bilayer, thus allowing for the incorporation of complex channels proteins which are failed in non-diluted systems. The tBLM is completed by fusion of liposomes made from a mixture of 1,2-diphythanolyl-sn-glycero-3-phosphocholine (DPhyPC), cholesterol, and 1,2-diphytanoyl-sn-Glycero-3-phosphate (DPhyPG) in a molar ratio of 6:3:1. Varying the mixing ratio, the optimum mixing ratio was obtained at a dilution factor of DPTL and TEGL at 90%:10%. Only under these conditions, the mixed tBLM showed electrical properties, as shown by EIS, which are comparable to a BLM. With higher dilution factors, a defect-free lipid bilayer was not formed. Formation of bilayers have been characterized by different techniques, such as surface plasmon resonance (SPR), electrochemical impedance spectroscopy (EIS), atomic force microscopy (AFM), and quartz crystal microbalance (QCM). Different proteins such as hemolysin, melittin, gramicidin, M2, Maxi-K, nAChR and bacteriohodopsin are incorporated into these tBLMs as shown by SPR and EIS studies. Ionic conductivity at 0 V vs. Ag|AgCl, 3M KCl were measured by EIS measurements. Our results indicate that these proteins have been successfully incorporated into a very stable tBLM environment in a functionally active form. Therefore, we conclude that the mixed tBLMs have been successfully designed as a general platform for biosensing and screening purposes of membrane proteins.

Surface-plasmon optical and electrochemical characterization of biofunctional surface architectures

The development and characterization of biomolecule sensor formats based on the optical technique Surface Plasmon Resonance (SPR) Spectroscopy and electrochemical methods were investigated. The study can be divided into two parts of different scope. In the first part new novel detection schemes for labeled targets were developed on the basis of the investigations in Surface-plamon Field Enhanced Spectroscopy (SPFS). The first one is SPR fluorescence imaging formats, Surface-plamon Field Enhanced Fluorescence Microscopy (SPFM). Patterned self assembled monolayers (SAMs) were prepared and used to direct the spatial distribution of biomolecules immobilized on surfaces. Here the patterned monolayers would serve as molecular templates to secure different biomolecules to known locations on a surface. The binding processed of labeled target biomolecules from solution to sensor surface were visually and kinetically recorded by the fluorescence microscope, in which fluorescence was excited by the evanescent field of propagating plasmon surface polaritons. The second format which also originates from SPFS technique, Surface-plamon Field Enhanced Fluorescence Spectrometry (SPFSm), concerns the coupling of a fluorometry to normal SPR setup. A spectrograph mounted in place of photomultiplier or microscope can provide the information of fluorescence spectrum as well as fluorescence intensity. This study also firstly demonstrated the analytical combination of surface plasmon enhanced fluorescence detection with analyte tagged by semiconducting nano- crystals (QDs). Electrochemically addressable fabrication of DNA biosensor arrays in aqueous environment was also developed. An electrochemical method was introduced for the directed in-situ assembly of various specific oligonucleotide catcher probes onto different sensing elements of a multi-electrode array in the aqueous environment of a flow cell. Surface plasmon microscopy (SPM) is utilized for the on-line recording of the various functionalization steps. Hybridization reactions between targets from solution to the different surface-bound complementary probes are monitored by surface-plasmon field-enhanced fluorescence microscopy (SPFM) using targets that are either labeled with organic dyes or with semiconducting quantum dots for color-multiplexing. This study provides a new approach for the fabrication of (small) DNA arrays and the recording and quantitative evaluation of parallel hybridization reactions. In the second part of this work, the ideas of combining the SP optical and electrochemical characterization were extended to tethered bilayer lipid membrane (tBLM) format. Tethered bilayer lipid membranes provide a versatile model platform for the study of many membrane related processes. The thiolipids were firstly self-assembled on ultraflat gold substrates. Fusion of the monolayers with small unilamellar vesicles (SUVs) formed the distal layer and the membranes thus obtained have the sealing properties comparable to those of natural membranes. The fusion could be monitored optically by SPR as an increase in reflectivity (thickness) upon formation of the outer leaflet of the bilayer. With EIS, a drop in capacitance and a steady increase in resistance could be observed leading to a tightly sealing membrane with low leakage currents. The assembly of tBLMs and the subsequent incorporation of membrane proteins were investigated with respect to their potential use as a biosensing system. In the case of valinomycin the potassium transport mediated by the ion carrier could be shown by a decrease in resistance upon increasing potassium concentration. Potential mediation of membrane pores could be shown for the ion channel forming peptide alamethicin (Alm). It was shown that at high positive dc bias (cis negative) Alm channels stay at relatively low conductance levels and show higher permeability to potassium than to tetramethylammonium. The addition of inhibitor amiloride can partially block the Alm channels and results in increase of membrane resistance. tBLMs are robust and versatile model membrane architectures that can mimic certain properties of biological membranes. tBLMs with incorporated lipopolysaccharide (LPS) and lipid A mimicking bacteria membranes were used to probe the interactions of antibodies against LPS and to investigate the binding and incorporation of the small antimicrobial peptide V4. The influence of membrane composition and charge on the behavior of V4 was also probed. This study displays the possibility of using tBLM platform to record and valuate the efficiency or potency of numerous synthesized antimicrobial peptides as potential drug candidates.