Ecologia alimentar e reprodutiva da piaba-do-rabo-amarelo, Astyanax cf. lacustris (Reinhardt, 1874) (Osteichthyes: Characidae) na Lagoa do Piató, Assu, Rio Grande do Norte, Brasil

The feeding habits and biological aspects of the reproductive cycle of two-spot astyanax, Astyanax cf. lacustris (Reinhardt, 1874) were investigated. Fish samples were captured on a monthly basis, using gillnets of 4 cm mesh size, from the Piató Lake, Assu, Rio Grande do Norte, during the period of September, 2006 to August, 2007. Physico-chemical parameters, such as, temperature, electrical conductivity and dissolved oxygen of the lake were registered. The monthly values of rainfall also were obtained. The 360 individuals captured, were measured, weighed, dissected, and stomach weight and the stage of gonadal maturity were registered. The stomach contents analyses were carried out based on volumetric method, points, frequency of occurrence and applying the Index of Relative Importance. The degrees of repletion of the stomachs were determined besides the Index of Repletion relating to feeding activity variations and frequency of ingestion with limnological parameters and rainfall. The food items identified were separated into distinct groups according to their origin. Sex ratio and Gonadosomatic Relation of females were verified to determine the spawning period and fecundity. The physico-chemical parameters presented the following annual mean values: temperature = 28.8ºC, electrical conductivity = 992.5 µS.cm-1; dissolved oxygen = 4.9 mg.L-1 during the study period. The annual mean of the rainfall was 63.5 mm. The results indicate that this species present an omnivorous feeding habit with a tendency towards insectivory, with an increase in feeding activity during the dry season. The aquatic oxygen to interfere very importance in the feeding activity than the others factors physico-chemicals of water and rainfall. There was a predominance of females, with a sex proportion of 1M:7F. The macroscopic characteristics of the ovaries and testicles revealed four stages of gonadal development: immature, maturing, mature and spent. A temporal variation was observed for the gonadal development of males and females. There was reproductive activity through out the year, with peaks in the months of February, April and June to correspond with the rain of precipitation of the region. The mean fecundity was 7.681 mature oocytes, varying from 4.476 to 12.036, with mean of 7.681. There was positive relation between fecundity and body mass. Condition Factor is not an efficient indicator of the reproductive period of this species. The species A. cf. lacustris is an opportunist and is well adapted to the conditions of the semi-arid Caatinga Biome

Resposta imune à saliva de flebotomíneos (diptera: psychodidae) em indivíduos residentes em áreas urbana e periurbana no nordeste do brasil

Visceral leishmaniasis (VL) has a wide geographical distribution in tropical and subtropical areas of the planet, which is a protozoan parasite of the genus Leishmania. This pathogen is transmitted to the host through the sandflies bite, with its saliva, the immune response that leads to both. In the state of Rio Grande do Norte, 85% of the sand flies captured is Lutzomyia longipalpis, but the second most abundant, Lutzomyia evandroi, it deserves emphasis because its wide distribution and eclectic behavior. The exposure of people living in endemic areas for the insect vector VL greatly increases the chances of infection. This study aimed to evaluate aspects of the epidemiological profile of VL in endemic areas of human and nonendemic in the metropolitan area of Natal, as well as verify the abundance and seasonal fluctuations of sandflies species in two counties endemic for VL. Were collected in the municipalities of Nísia Floresta, Parnamirim, São Gonçalo do Amarante and Macaíba, of which groups of females were separated for further dissection of the salivary glands and identification of species. The blood samples used were from individuals of two Natal s districts where it has never been reported cases of VL and neighborhoods of Parnamirim applicants who present cases of VL. In the municipality of Nísia Floresta, the most abundant species was L. evandroi with 38.39%, followed by L. longipalpis with 36.22%, L. walkeri 19.67% L. lenti 3.81%, L. wellcomei 1.39% and L. whitmani 0.52%. Already in Parnamirim the proportions were L. walkeri with 73.15%, L. evandroi with 10.55%, L. wellcomei 7.63%, L. longipalpis 6.37%, L. whitmani 1.46%, L. sordellii 0.52%, L. intermedia 0.21 and L. shanonni 0.1%. In both municipalities was observed higher abundance of species distributed in the initial months of the year, as February and March. The study showed that no difference in exposure to the vector of VL among individuals from endemic and non endemic area for this disease. But there are differences in exposure between individuals of L. longipalpis and L. evandroi, confirming the great powers of the first vector. It was also characterized as predominant phenotype in the population of endemic areas who had negative serologic responses to antigens of Leishmania and result in negative Montenegro skin test (DTH), indicating that much of the population hasn t been bitten by infected insects

Influência do teor de calcário no comportamento físico, mecânico e microestrutural de cerâmicas estruturais

There are ores of clay in Piauí State that are used for red structural ceramics, which are naturally contaminated with calcareous vein. This is one thing that impedes its exploration in an adequate way, especially for tile production. The present work aims at verifying the influence of the calcareous contents in the technological structural ceramics area, seeking to determine a maximum permissible calcareous proportion/contents in the ceramic mass using the patterns of the local industry production. For the consecution of this paper, it was characterized the clay and calcareous material by FRX, DRX, TGA and DTA. It was also configurated by extrusion and burnt in the temperatures of 850°C, 900°C, 950°C and 1000°C pieces of the corpus with 0, 5, 10, 15 e 20% of calcareous proportion. After that, it was carried out technological samples of linear retraction, water absortion, apparent porosity, specific apparent mass and mechanic resistance. The results showed the possibility of using calcareous in the ceramic mass and in some cases the technological properties got better

Estudo do comportamento plástico, mecânico, microestrutural e térmico do concreto produzido com resíduo de porcelanato

Population growth experienced in major cities, allied to society s need of infra-structure, especially ones related to habitational demands, increases the consumption of construction materials. As a consequence, consumption of natural resources itself. Thus, due to this process, concrete is one of the most produced materials in civil construction. This is also due to the great diversity of its application, easiness in its execution and adequate mechanical performance, as well as low production costs. Following the same tendencies in construction development, the ceramic industry has intensified the production of porcelain ceramic tiles and floors. These are achieved by a fine finishing and receive polishing at the end of the fabrication process. This work researched the use of porcelain residues in polishing for the production of concrete. All of which; due to economical and environmental issues. This process aims to prove adequate destiny for this type of residue, due to environmental issues, incorporating it to the concrete itself; all of which provides economy in consumption of the materials that constitute concrete. Thus, the main characteristics of concrete were investigated through the inclusion of different concentration of the porcelain residue as additional trait element. The residue rates incorporated to the trait varied from 10% to 50% in relation to the cement mass, in the traits with plastic additives and without plastic additives. It is observed that the inclusion of porcelain residue produced a meaningful alteration in the consistency of fresh concrete. This residue has a fine granulometry and it considerably absorbed the water used in the concrete spreading, influencing the way this material is dealt with. Thus, the value of cement striking decreases with the increase of residues present in trait. The maximal incorporation of the residue was of 50%, massively, for the same factor water/initial cement. The use of residues in concrete results in an 40% increase in the compression resistance. It is also proportional to residue concentration of porcelain in the trait. The microstructure was also favored once porosity and concrete absorption decreases with the use of this residue. The parameters demonstrate the quality and durability of the concrete produced with this residue. The use of porcelain residue in concrete composition has not produced meaningful thermal behavior changes. Thermal conductivity, heat capacity and thermal diffusivity have been maintained basically constant

Estudos de Durabilidade Frente ao Ataque Ácido de Compósitos Portland-Polímero para Cimentação de Poços de Petróleo

Portland-polymers composites are promising candidates to be used as cementing material in Northeastern oil wells of Brazil containing heavy oils submitted to steam injection. In this way, it is necessary to evaluate its degradation in the commonly acidizind agents. In addition, to identify how aggressive are the different hostile environments it is an important contribution on the decision of the acidic systems to be used in. It was investigated the performance of the Portland-polymer composites using powdered polyurethane, aqueous polyurethane, rubber tire residues and a biopolymer, those were reinforced with polished carbon steel SAE 1045 to make the electrochemical measurements. HCl 15,0 %, HCl 6,0 % + HF 1,5 % (soft mud acid), HCl 12,0 % + HF 3,0 % (regular mud acid) and HAc 10 % + HF 1,5 % were used as degrading environment and electrolytes. The more aggressive acid solution to the plain Portland hardened cement paste was the regular mud acid, that showed loss of weight around 23.0 %, followed by the soft mud acid, the showed 11.0 %, 15.0 % HCl with 7,0 % and, at last the 10.0 % HAc plus HF 1.5 % with just 1.0 %. The powdered polyurethane-composite and the aqueous polyurethane one showed larger durability, with reduction around 87.0 % on the loss of weight in regular mud acid. The acid attack is superficial and it occurs as an action layer, where the degraded layer is responsible for the decrease on the kinetic of the degrading process. This behavior can be seen mainly on the Portland- aqueous polyurethane composite, because the degraded layer is impregnated with chemically modified polymer. The fact of the acid attack does not have influence on the compressive strength or fratography of the samples, in a general way, confirms that theory. The mechanism of the efficiency of the Portland-polymers composites subjected to acid attack is due to decreased porosity and permeability related with the plain Portland paste, minor quantity of Ca+2, element preferentially leached to the acidic solution, wave effect and to substitute part of the degrading bulk for the polymeric one. The electrolyte HAc 10 % + HF 1,5 % was the least aggressive one to the external corrosion of the casing, showing open circuit potentials around +250 mV compared to -130 mV to the simulated pore solution to the first 24 hours immersion. This behavior has been performed for two months at least. Similar corrosion rates were showed between both of the electrolytes, around 0.01 μA.cm-2. Total impedance values, insipient arcs and big polarization resistance capacitive arcs on the Nyquist plots, indicating passivity process, confirm its efficiency. In this way, Portlandpolymers composites are possible solutions to be succeed applied to oilwell cementing concomitant submitted to steam injection and acidizing operation and the HAc 10,0 % + HF 1,5 % is the less aggressive solution to the external corrosion of the casing

Estudo de massa cerâmica triaxial visando à otimização do ciclo de queima da indústria de cerâmica estrutural

Over recent years the structural ceramics industry in Brazil has found a very favorable market for growth. However, difficulties related to productivity and product quality are partially inhibiting this possible growth. An alternative for trying to solve these problems and, thus, provide the pottery industry the feasibility of full development, is the substitution of firewood used in the burning process by natural gas. In order to contribute to this process of technological innovation, this paper studies the effect of co-use of ceramic phyllite and kaolin waste on the properties of a clay matrix, verifying the possible benefits that these raw materials can give to the final product, as well as the possibility of such materials to reduce the heat load necessary to obtain products with equal or superior quality. The study was divided into two steps: characterization of materials and study of formulations. Two clays, a phyllite and a residue of kaolin were characterized by the following techniques: laser granulometry, plasticity index by Atterberg limits, X-ray fluorescence, X-ray diffraction, mineralogical composition by Rietveld, thermogravimetric and differential thermal analysis. To study the formulations, specifically for evaluation of technological properties of the parts, was performed an experimental model that combined planning involving a mixture of three components (standard mass x phyllite x kaolin waste) and a 23 factorial design with central point associated with thermal processing parameters. The experiment was performed with restricted strip-plot randomization. In total, 13 compositional points were investigated within the following constraints: phyllite ≤ 20% by weight, kaolin waste ≤ 40% by weight, and standard mass ≥ 60% by weight. The thermal parameters were used at the following levels: 750 and 950 °C to the firing temperature, 5 and 15 °C/min at the heating rate, 15 and 45min to the baseline. The results showed that the introduction of phyllite and/or kaolin waste in ceramic body produced a number of benefits in properties of the final product, such as: decreased absorption of water, apparent porosity and linear retraction at burn; besides the increase in apparent specific mass and mechanical properties of parts. The best results were obtained in the compositional points where the sum of the levels of kaolin waste and phyllite was maximal (40% by weight), as well as conditions which were used in firing temperatures of 950 °C. Regarding the prospect of savings in heat energy required to form the desired microstructure, the phyllite and the residue of kaolin, for having small particle sizes and constitutions mineralogical phases with the presence of fluxes, contributed to the optimization of the firing cycle.

Comportamento magnético de compósitos de matriz polimérica com adição de ferritas

Polymer matrix composites offer advantages for many applications due their combination of properties, which includes low density, high specific strength and modulus of elasticity and corrosion resistance. However, the application of non-destructive techniques using magnetic sensors for the evaluation these materials is not possible since the materials are non-magnetizable. Ferrites are materials with excellent magnetic properties, chemical stability and corrosion resistance. Due to these properties, these materials are promising for the development of polymer composites with magnetic properties. In this work, glass fiber / epoxy circular plates were produced with 10 wt% of cobalt or barium ferrite particles. The cobalt ferrite was synthesized by the Pechini method. The commercial barium ferrite was subjected to a milling process to study the effect of particle size on the magnetic properties of the material. The characterization of the ferrites was carried out by x-ray diffraction (XRD), field emission gun scanning electron microscopy (FEG-SEM) and vibrating sample magnetometry (VSM). Circular notches of 1, 5 and 10 mm diameter were introduced in the composite plates using a drill bit for the non-destructive evaluation by the technique of magnetic flux leakage (MFL). The results indicated that the magnetic signals measured in plates with barium ferrite without milling and cobalt ferrite showed good correlation with the presence of notches. The milling process for 12 h and 20 h did not contribute to improve the identification of smaller size notches (1 mm). However, the smaller particle size produced smoother magnetic curves, with fewer discontinuities and improved signal-to-noise ratio. In summary, the results suggest that the proposed approach has great potential for the detection of damage in polymer composites structures

Adição de subprodutos da cinza da casca de café (coffea canephora) em massa cerâmica para porcelanato

To produce porcelain tiles fluxing agents are used in order to obtain a liquid phase during firing. This liquid phase fills the pores decreasing porosity, water absorption and contributes to material densification. In the porcelain tiles industry, feldspar is the main flux material used, with quantities ranging between 35 and 50%. Studies focus on the discovery of materials with flux characteristics that can reduce the consumption of feldspar by porcelain tiles industry. In this context, the coffee husk ashes, a residue obtained when coffee husks are burned to produce heat for the dryers during the processing of the green fruit, have as main chemical constituents potassium, calcium and magnesium, giving them characteristics of fluxing material. Brazil is the largest coffee producer in the world and is responsible for over 30% of the world s production. In this work a physical treatment of coffee husk ash was carried out in order to eliminate the organic matter and, after this, two by-products were obtained: residual wastes R1 and R2. Both residues were added separately as single fluxes and also in association with feldspar in mixtures with raw materials collected in a porcelain industry located in Dias d Ávila-Ba. The addition of these residues aimed to contribute to the reduction of the consumption of feldspar in the production of porcelain tiles. Specimens were produced with dimensions of 60 mm x 20 mm x 6 mm in an uniaxial die with compacting pressure of 45 MPa. The samples were heated to a temperature of 1200 °C, for 8 minutes. Tests were performed to characterize the raw materials by XRF, XRD, particle size analysis, DTA and TGA and, additionally, the results of the physical properties of water absorption, apparent porosity, linear shrinkage, density, dilatometry, flexural strength and SEM of sintered body were analyzed. Additions of less than 8% of the residue R1 contributed to the decrease of porosity, but the mechanical strength of the samples was not satisfactory. Additions of 5% the R2 residue contributed significantly to decrease the water absorption and apparent porosity, and also to increase the mechanical strength. Samples with addition of feldspar associated with the R2 residue, in proportions of 6.7% of R2 and 6.7% of feldspar, led to results of water absorption of 0.12% and mechanical strength of 46 MPa, having parameters normalized to the manufacture of porcelain stoneware tiles

Efeito da adição de fibras da palma do licuri (syagrus coronata) no comportamento físico e mecânico de compósitos de matriz cimentícia

This research was motivated by the requirement of asbestos s replacement in building systems and the need to generate jobs and income in the country side of the state of Bahia, Brazil. The project aimed at using fibers from licuri leaves (syagrus coronata), an abundant palm in the region, to produce composites appropriate for the sustainable production of cement fibre reinforced products in small plants. The composites were produced in laboratory using Portland cement CP-II-F32, sand, water, licuri palm fiber contents of 1.0, 1.5 and 2.0% by weight of binder (two different fiber length) and metakaolin. The latter was chosen as an additional binder for its efficiency to reduce the alkalinity of cementitious matrixes therefore preventing the degradation of vegetable fibers. The characterization of the composite components was carried out by sieving and laser particle size analyses, thermal analysis, fluorescence and X-ray diffraction. The composites performance was evaluated by 3- point-bending tests, compressive strength, ultrasound module of elasticity, free and restrained shrinkage, water capillarity absorption and apparent specific gravity. It has been found that the addition of fibers increased the time to onset of cracking over 200.00% and a 25% reduction in cracks opening in the restrained shrinkage test. The capillary absorption reduced about 25% when compared to fiber-free composites. It was also observed with regard to flexural strength, compressive strength and specific gravity, that the addiction of fibers did not affect the composite performance presenting similar results for compounds with and without fibers. In general it can be stated that the reinforced composite fibers of palm licuri presents physical and mechanical characteristics which enable them to be used in the intended proposals of this research

Influência da adição de gres porcelanato no comportamento mecânico e microestrutural em pastas de cimento portland para cimentação de poços de petróleo

Cementation operation consists in an extremely important work for the phases of perforation and completion of oil wells, causing a great impact on the well productivity. Several problems can occur with the cement during the primary cementation, as well as throughout the productive period. The corrective operations are frequent, but they are expensive and demands production time. Besides the direct cost, prejudices from the interruption of oil and gas production till the implementation of a corrective operation must be also taken into account. The purpose of this work is the development of an alternative cement paste constituted of Portland cement and porcelainized stoneware residue produced by ceramic industry in order to achieve characteristics as low permeability, high tenacity, and high mechanical resistance, capable of supporting various operations as production or oil wells recuperation. Four different concentration measures of hydrated paste were evaluated: a reference paste, and three additional ones with ceramic residue in concentrations of the order of 10%, 20% and 30% in relation to cement dough. High resistance and low permeability were found in high concentration of residues, as well as it was proved the pozolanic reactivity of the residue in relation to Portland cement, which was characterized through x-ray and thermogravimetry assays. It was evident the decrease of calcium hydroxide content, once it was substituted by formation of new hydrated products as it was added ceramic residue

Atividade antiplasmódica e toxicológica de plantas medicinais usadas popularmente no Brasil : uma abordagem etnobotânica

Malaria is a disease of global distribution, recognized by governments around the world as a serious public health problem, affecting more than 109 countries and territories and endangering more than 3.3 billion people. The economic costs of this disease are also relevant: the African continent itself has malaria-related costs of about $ 12 billion annually. Nowadays, in addition to chloroquine, Plasmodium falciparum is resistant to many drugs used in the treatment of malaria, such as amodiaquine, mefloquine, quinine and sulfadoxine-pyrimethamine; resistance of Plasmodium vivax to treatments, although less studied, is also reported. Nature, in general, is responsible for the production of most known organic substances, and the plant kingdom is responsible for the most of the chemical diversity known and reported in the literature. Most medicinal plants commercialized in Brazil, however, are of exotic origin, which makes the search for endemic medicinal plants, besides a patent necessity, a fascinating subject of academic research and development. This study aimed to: (i) verify the antimalarial activity of ethanolic and hydroalcoholic extracts of Boerhavia paniculata Rich. And acetonic extract of Clethra scabra Pers. in Swiss albino mice infected by Plasmodium berghei NK65, (ii) observe possible combined effects between the course of infection by P. berghei NK65 and administration of these extracts in Swiss albino mice, and (iii) conduct a preliminary study of the acute toxicity of these extracts in Swiss albino mice. All extracts notable pharmacological activities - with parasite infections inhibitions ranging from 22% to 54%.These characteristics suggest that the activities are relevant, although comparatively lower than the activity displayed by the positive control group (always above 90%). The general framework of survival analysis demonstrates an overall reduction in survival times for all groups. Necroscopy has not pointed no change in color, shape, size and/or consistency in the evaluated organs - the only exception was the livers of rats submitted to treatment to hydroalcoholic extracts: these organs have been presented in a slightly congestive aspect with mass increasing roughly 28% higher than the other two groups and a p-value of 0.0365. The 250 mg/Kg ethanolic group has been pointed out by the Dunn s post test, as the only class with simultaneous inequalities (p<0.05) between positive and negative control groups. The extracts, notably ethanol extract, have, in fact, a vestigial antimalarial activity, although well below from the ones perceived to chloroquine-treated groups; nevertheless, the survival times of the animals fed with the extracts do not rise by presence of such therapy. Both the toxicopharmacological studies of the synergism between the clinical course of malaria and administration of extracts and the isolated evaluation of toxicity allow us to affirm the absence of toxicity of the extracts at the level of CNS and ANS, as well as their non-influence on food and water consumption patterns, until dosages of 500 mg/Kg. Necroscopic analysis leads us to deduct a possible hepatotoxic effect of hydroalcoholic extract at dosages of 500 mg/Kg, and an innocuous tissue activity of the ethanol extract, in the same dosage. We propose a continuation of the studies of these extracts, with protocol modifications capable of addressing more clearly and objectively their pharmacological and toxicological aspects

Estudo estatístico sobre eventos de precipitação intensa no nordeste do Brasil

The Northeast of Brazil (NEB) shows high climate variability, ranging from semiarid regions to a rainy regions. According to the latest report of the Intergovernmental Panel on Climate Change, the NEB is highly susceptible to climate change, and also heavy rainfall events (HRE). However, few climatology studies about these episodes were performed, thus the objective main research is to compute the climatology and trend of the episodes number and the daily rainfall rate associated with HRE in the NEB and its climatologically homogeneous sub regions; relate them to the weak rainfall events and normal rainfall events. The daily rainfall data of the hydrometeorological network managed by the Agência Nacional de Águas, from 1972 to 2002. For selection of rainfall events used the technique of quantiles and the trend was identified using the Mann-Kendall test. The sub regions were obtained by cluster analysis, using as similarity measure the Euclidean distance and Ward agglomerative hierarchical method. The results show that the seasonality of the NEB is being intensified, i.e., the dry season is becoming drier and wet season getting wet. The El Niño and La Niña influence more on the amount of events regarding the intensity, but the sub-regions this influence is less noticeable. Using daily data reanalysis ERAInterim fields of anomalies of the composites of meteorological variables were calculated for the coast of the NEB, to characterize the synoptic environment. The Upper-level cyclonic vortex and the South atlantic convergene zone were identified as the main weather systems responsible for training of EPI on the coastland