Electrochemical and metallurgical industry.

Title from cover.

Bulletin de la Société chimique de France

Mode of access: Internet.

Material and energy balances /

Mode of access: Internet.

Afffinity tag excision strategies for Car9-tagged proteins

Thesis (Master's)--University of Washington, 2016-06

Bioinspired Anti-fouling Coating on Hydrophobic Surfaces

Thesis (Master's)--University of Washington, 2016-06

Mixed-charge copolymer as environmentally friendly low fouling marine coatings

Thesis (Master's)--University of Washington, 2016-06

Characterization and Degradation of Fatty Acid Methyl Esters and Biodiesel in Artificial Seawater Under UV Exposure Using Raman Spectroscopy

Thesis (Master's)--University of Washington, 2016-06

Remote Control Electrodeposition: Patterning on Substrates without Direct Electrical Connections

Thesis (Ph.D.)--University of Washington, 2016-06

Chemically-Addressable Protein Entrapment in Silica Sol-Gels

Thesis (Master's)--University of Washington, 2016-06

Improving the Manufacturability of Active Microfluidic Devices using Stereolithography (SL)

Thesis (Master's)--University of Washington, 2016-06

A population balance model for high shear granulation

In a previous paper, Hoornaert et al. (Powder Technol. 96 (1998); 116-128) presented data from granulation experiments performed in a 50 L Lodige high shear mixer. In this study that same data was simulated with a population balance model. Based on an analysis of the experimental data, the granulation process was divided into three separate stages: nucleation, induction, and coalescence growth. These three stages were then simulated separately, with promising results. it is possible to derive a kernel that fit both the induction and the coalescence growth stage. Modeling the nucleation stage proved to be more challenging due to the complex mechanism of nucleus formation. From this work some recommendations are made for the improvement of this type of model.

Strength and attrition resistance of agglomerates and particulate coatings

The mechanical properties of a range of agglomerates and particulate coatings have been measured using a nanoindenter. The effect of formulation properties such as powder and binder properties on coating hardness is described. An attempt is also made to measure the fracture hardness with the nanoindenter. The use of indentation technology to measure fundamental agglomerate properties is critically analysed. Based on the indentation measurements and standard attrition test results, the coating hardness is found closely related to the attrition rate under standard conditions and can be used to screen different powder/binder formulations. (C) 2002 Elsevier Science B.V All rights reserved.

Structural and mechanical properties of nanostructured granular alumina catalysts

Granular gamma-Al2O3 support and 8 wt % CuO/gamma-Al2O3 catalyst were synthesized by a sol-gel granulation method. The pore structure, crush strength, hardness, and elasticity of these sol-gel-derived catalysts were studied and compared with similar commercial catalysts prepared by non-sol-gel methods. Alumina and CuO-coated alumina granular particles prepared by different methods have different macro- and microstructure. The sol-gel-derived granular gamma-alumina and CuO-coated gamma-alumina granular particles have a structure defined by compact packing of uniform, nanosized gamma-alumina crystallites. They are characterized by a more uniform pore size distribution and larger surface area as compared to similar commercial samples with a structure defined by packing of aggregates consisting of nonuniform gamma-alumina crystallites. Because of the differences in the macro- and microstructure, the sol-gel-derived granular samples offer higher crush strength and greater hardness than the commercial samples.

Nucleation regime map for liquid bound granules

Nucleation is the first step in granulation where the powder and liquid first contact. Two types of nucleation in wet granulation processes are proposed. Drop controlled nucleation, where one drop forms one nucleus, occurs when drops hitting the powder surface do not overlap (low spray flux Psi(a)) and the drop must wet quickly into the bed (short drop penetration time t(p)). If either criterion is not met, powder mixing characteristics will dominate (mechanical dispersion regime). Granulation experiments were performed with lactose powder, water, PEG200, and 7% HPC solution in a 6 L and a 25 L mixer granulator. Size distributions were measured as the drop penetration time and spray flux were varied. At short penetration times, decreasing Psi(a) caused the nuclei distribution to become narrower. When drop penetration time was high, the nuclei size distribution was broad independent of changes in dimensionless spray flux. Nucleation regime maps were plotted for each set of experiments in each mixer as a function of the dimensionless distribution width delta. The nucleation regime map demonstrates the interaction between drop penetration time and spray flux in nucleation. The narrowest distribution consistently occurred at low spray flux and low penetration time, proving the existence of the drop controlled regime. The nucleation regime map provides a rational basis for design and scale-up of nucleation and wetting in wet granulation.

Flow patterns in granulating systems

Particle flow patterns were investigated for wet granulation and dry powder mixing in ploughshare mixers using Positron Emission Particle Tracking (PEPT). In a 4-1 mixer, calcium carbonate with mean size 45 mum was granulated using a 50 wt.% solution of glycerol and water as binding fluid, and particle movement was followed using a 600-mum calcium hydroxy-phosphate tracer particle. In a 20-1 mixer, dry powder flow was studied using a 600-mum resin bead tracer particle to simulate the bulk polypropylene powder with mean size 600 mum. Important differences were seen between particle flow patterns for wet and dry systems. Particle speed relative to blade speed was lower in the wet system than in the dry system, with the ratios of average particle speed to blade tip speed for all experiments in the range 0.01-015. In the axial plane, the same particle motion was observed around each blade; this provides a significant advance for modelling flow in ploughshare mixers. For the future, a detailed understanding of the local velocity, acceleration and density variations around a plough blade will reveal the effects of flow patterns in granulating systems on the resultant distribution of granular product attributes such as size, density and strength. (C) 2002 Elsevier Science B.V All rights reserved.