Painéis-sanduíche com núcleo de EPS reciclado: metodologia de execução e determinação de propriedades termofísicas

New materials made from industrial wastes have been studied as an alternative to traditional fabrication processes in building and civil engineering. These materials are produced considering some issues like: cost, efficiency and reduction of nvironmental damage. Specifically in cases of materials destined to dwellings in low latitude regions, like Brazilian Northeast, efficiency is related to mechanical and thermal resistance. Thus, when thermal insulation and energetic efficiency are aimed, it s important to increase thermal resistance without depletion of mechanical properties. This research was conducted on a construction element made of two plates of cement mortar, interspersed with a plate of recycled expanded polystyrene (EPS). This component, widely known as sandwich-panel, is commonly manufactured with commercial EPS whose substitution was proposed in this study. For this purpose it was applied a detailed methodology that defines parameters to a rational batching of the elements that constitute the nucleus. Samples of recycled EPS were made in two different values of apparent specific mass (ρ = 65 kg/m³; ρ = 130 kg/m³) and submitted to the Quick-Line 30TM that is a thermophysical properties analyzer. Based on the results of thermal conductivity, thermal capacity and thermal diffusivity obtained, it was possible to assure that recycled EPS has thermal insulation characteristics that qualify it to replace commercial EPS in building and civil engineering industry

Análise das propriedades termofísicas, mecânicas e geométricas de telhas cerâmicas queimadas em forno caieira e forno abóbada

In the industry of ceramic in Rio G. do Norte, tile stands out as the most manufactured product by this industry, being the intermittent kiln abóbada and caieira the principal type of kiln used in burning. There was a need to make a study of the influence exerted by the type of kiln in which tiles are burnt in their thermo physical properties. The analysis started with 24 raw samples of tile, which was split in two groups of 12 samples and burnt in Abóbada and Caieira kiln. Besides that, it was made study of the tax of heat transfer to the environment (for each kiln). After having been burnt the samples were taken for laboratory analysis. The properties verified were impermeability, determination of dry mass, absorption of water, the load of bending rupture and its geometric characteristics, the tests were conducted following the currents standards. The tests were carried out according to the ABNT - NBR 15310. The calculation of the rate of heat transfer showed that the abóbada kiln is more efficient than the Caieira, however the results of tests on the samples revealed no superiority of one over another sample. So the furnace had no influence on the performance of the ceramic tiles

Análise comparativa entre propriedades mecânicas, termofísicas e geométricas de tijolos produzidos pelos fornos caieira e abóbada

In the State of Rio Grande do Norte potteries are distributed in several counties in the four meso, which are: West Potiguar, Center Potiguar, Agreste Potiguar and East Portiguar. The ceramics, mostly, are responsible for products used in construction as bricks, tiles and white brick and wood used as fuel. This paper had a primary focus in the region of Seridó. The furnaces in this region, used to manufacture bricks are configured Caieira and Valt, in most of them using principles rustic, usually operated in an empirical way, using principles of control rather primitive, predominantly visual control. The focus of this study was to analyze the differences in the thermophysical, mechanical and geometric characteristics of bricks produced by Caieira and vault furnaces, using the NBR 15720 and the evaluation of energy efficiency in both furnaces. Thermophysical characteristics were analyzed through tests to determine the water absorption obtained from the difference between dry mass and wet mass of the sample and analysis of the thermal gradient, the mechanical characteristics from determination of the compressive strength of ceramic brick popularly known as bricks and also analyzed the geometrical characteristics of the bricks in order to verify the homogeneity of manufacturing. The tests showed that the energy difference of the two furnaces is not considered responsible for a significant difference in the properties of the products

Estudo das propriedades mecânicas de biocompósitos de polipropileno reforçados com fibras naturais

This research presents an approach to the addition of curauá fibers and licuri fibers in a polypropylene resin matrix, such as an alternative proposal to reinforce the polymeric composites. Fiber content of 0 %, 5 %, 10 %, and 20% were analyzed for verification of their mechanical properties comparing them, inclusive with the properties of polypropylene. The grainulated biocomposites had been prepared in an extrusora. The test bodies had been molded by injection and submitted to the mechanical essays uniaxial traction, flexion on three points, impact, in addition to thermal tests (HDT). These biocomposites had been also subjected the essay physicist-chemistry index of fluidity (IF). It was observed that the biocomposites of PP with 20% curauá, obtained bigger increase in the modulus of elasticity and a bigger reduction in the resistance to the impact. In the mechanical behavior, for all the biocomposites, these were increases in values of the limit of drainage and tension of rupture, when tested by uniaxial traction, as they added the fibers. Another important point was the increase of the resistance the flexion. It was also noted that the addition of fibers reduced the thermal degradation of the mixture natural fibers / polypropylene.

Reguladores vegetais no desenvolvimento e produtividade da cana-de-açúcar

O objetivo deste trabalho foi avaliar o desenvolvimento e a produtividade de colmos de cana-de-açúcar, resultantes da aplicação de reguladores vegetais no iníco da safra. Ostratamentos consistiram na aplicação de três reguladores vegetais inibidores de crescimento - sulfometuron metil, glifosato e compostos de radicais carboxílicos orgânicos + glifosato - e na maturação natural como testemunha, em delineamento experimental em blocos ao acaso, com cinco repetições. Os maturadores retardam o processo de crescimento em altura das plantas, sem afetar o número e o diâmetro de colmos na colheita, e influenciam de forma e intensidade distintas a ocorrência do florescimento e chochamento. O glifosato proporciona elevados índices de brotação lateral e prejudica a rebrota da soqueira. Os maturadores induzem o aumento do teor de açúcares redutores totais, o que contribui para a melhoria da qualidade tecnológica da cana-de-açúcar.

Propriedades físicas do solo em sistemas de rotação de culturas conforme o uso de corretivos da acidez

O objetivo deste trabalho foi avaliar o efeito de sistemas de rotação de culturas e de corretivos da acidez nas propriedades físicas do solo. O experimento foi realizado entre outubro de 2006 e julho de 2008, em Botucatu, SP, em blocos ao acaso, com parcelas subdivididas e oito repetições. As parcelas foram constituídas por quatro sistemas de rotação: soja/pousio/milho/pousio, soja/aveia-branca/milho/feijão, soja/milheto/milho/guandu e soja/braquiária/milho/braquiária. As subparcelas consistiram do tratamento testemunha, sem correção, e da aplicação de 3,8 Mg ha-1 de calcário dolomítico (PRNT = 90%) ou de 4,1 Mg ha-1 de silicato de cálcio e magnésio (PRNT = 80%), na superfície de um Latossolo Vermelho argiloso. Foram determinadas: estabilidade de agregados, densidade do solo, porosidade total, macro e microporosidade, resistência do solo à penetração e umidade do solo. A aplicação dos corretivos de acidez em superfície não reduz a agregação do solo e aumenta a macroporosidade até 0,20 m de profundidade, após aplicação de silicato, e até 0,10 m, após aplicação de calcário. A manutenção do solo em pousio, na entressafra, prejudica a estruturação do solo, reduz a estabilidade de agregados e aumenta a resistência à penetração nas camadas superficiais. A semeadura de braquiária, entre as safras de verão, aumenta a estabilidade de agregados até 0,10 m de profundidade.

Estudo comparativo das propriedades mecânicas em compósitos da fibra modal e poliester

In the present work, three composites with distinct reinforcements (polyester, modal e polyester + modal), all if a unsaturated orthophthalic polyester resin as matrix were used, in order to conduct a comparative study by mechanical tests and water absorption. The fibre mats were prepared in a mat preparatory by immersion developed in the Textile Engineering Laboratory. The composites were manufactured using a closed mould process by compression using an unsaturated orthophthalic polyester resin as matrix and 1% MEK (methyl ethyl ketone peroxide) as an initiator. In each composite twelve samples with the dimensions of 150x25x3 mm were cut randomly for the mechanical analysis (tension x extension, three points bending and water absorption and Scanning Electron Micsroscopy). The mechanical tests were carried out in the Laboratório de Metais e Ensaios Mecânicos UFRN . All the analyses were carried out according to the ASTM norms. The resultant samples from the mechanical analysis were subjected for the Scanning Electron Microscopy analysis. Based on the results obtained, it was observed that the reinforced composite with two fibres (modal + polyester) presented better results in comparison to the other two composites both in the tension/extension as well on the three point bending tests. In the water absorption test, it was possible to observe an equilibrium in the water absorption by the modal and polyester composite, due to the union of the two fibres. In the SEM images, the regions of rupture in the composites as well as the adsorption between the fiber and the matrix could be observed

Caracterização e análise das propriedades da fibra de Macambira (Bromelia Laciniosa)

Concern for the environment and the exploitation of natural resources has motivated the development of research in lignocellulosic materials, mainly from plant fibers. The major attraction of these materials include the fact that the fibers are biodegradable, they are a renewable natural resource, low cost and they usually produce less wear on equipment manufacturing when compared with synthetic fibers. Its applications are focused on the areas of technology, including automotive, aerospace, marine, civil, among others, due to the advantageous use in economic and ecological terms. Therefore, this study aims to characterize and analyze the properties of plant fiber macambira (bromelia laciniosa), which were obtained in the municipality of Ielmo Marino, in the state of Rio Grande do Norte, located in the region of the Wasteland Potiguar. The characterization of the fiber is given by SEM analysis, tensile test, TG, FTIR, chemical analysis, in addition to obtaining his title and density. The results showed that the extraction of the fibers, only 0.5% of the material is converted into fibers. The results for title and density were satisfactory when compared with other fibers of the same nature. Its structure is composed of microfibrils and its surface is roughened. The cross section has a non-uniform geometry, therefore, it is understood that its diameter is variable along the entire fiber. Values for tensile strength were lower than those of sisal fibers and curauá. The degradation temperature remained equivalent to the degradation temperatures of other vegetable fibers. In FTIR analysis showed that the heat treatment may be an alternative to making the fiber hydrophobic, since, at high temperature can remove the hemicellulose layer, responsible for moisture absorption. Its chemical constitution is endowed with elements of polar nature, so their moisture is around 8.5% which is equivalent to the percentage of moisture content of hydrophilic fibers. It can be concluded that the fiber macambira stands as an alternative materials from renewable sources and depending on the actual application and purpose, it may achieve satisfactory results

Influência da umidade nas propriedades mecânicas dos compósitos poliméricos híbridos (sisal/ vidro)

This study aims to evaluate the mechanical properties of polymer matrix composites reinforced with sisal fabric bidirectional tissue (Agave sisalana,) and E-glass fibers, containing the following configuration: a polymer matrix hybrid composite (Polyester Resin orthophalic) reinforced with three (3) layers of glass fibers and alternating-2 (two) layers of bidirectional sisal fabric, and finally a composite of polymer matrix reinforced with five (5) layers of glass fiber mat-type E. For this purpose as first step, the preparation of by sisal, since they are not on the market. The composites were made by manual lamination (Hand lay-up) and evaluated for tensile properties and three point bending both in the dry, and wet conditions aswele as immersed in oil. Macroscopic and microscopic characteristics of the materialsweve awalysed, after the completion of the mechanical tests. After the studies, it was proven that the sisal fiber decreases the tensile stiffness of the material above 50% for both situations studied the tensile strength of the material decreases by approximately 40% for the cases mentioned, and when compared to the specific strength stiffness values drop to 14.6% and 29.02% respectively for the dry state only. Constants for bending the values were are to approximately 50% to 25% for strength and stiffness of the material for the cases dry, wet and immersed in oil. Under the influence of tension fluids do not interfere in the stiffness of the material for the bending tests, the same does not occur with the resistance, and these values are modified only in the cases stiffness and flexural strength

Morfologia e propriedades mecânicas da fibra de sisal unidirecional e em sobreposição de compósito com resina epóxi

The composites manufactured with long fibres aligned in a single direction, and overlay has been shown to have better performance than the short fibers randomly distributed. In particular, the lignocellulosic fibers extracted from the sisal leaves, used in conjunction with the epoxy resin has attracted the attention of many researchers because the final properties of the system formed. In this work composites based on epoxy resin reinforced with sisal fibers were manufactured. The sisal fibres were treated with an alkaline solution of 0.06 mol/l NaOH. The treated, and untreated fibres were subjected to tension x extension tests. The composites were manufactured in the "Lossy" mold with the specifications of the samples to be produced (300x20x4 mm). The tension tests were carried out in accordance with the ASTM standards 3039 (for the composite aligned in a single direction) and ASTM D5573 (for composites in overlay), three point bending tests were performed according to ASTM D790. Analyzing the results of the tests of tension and three point bending tests, it was observed that the composites with the configuration of overlapping had the better elastic module in both tests. As to the maximum resistance to tension, the best result was the composites aligned in a single direction. Tests of absorption of water and micrographs are in progress

Estudo das propriedades físico-químicas do biodiesel e suas influências na deterioração dos elastômeros aplicados no sistema de injeção dos motores diesel

The biodiesel use has become important due to its renewable character and to reduce environmental impacts during the fuel burning. Theses benefit will be valid if the fuel shows good performance, chemistry stability and compatibility with engines. Biodiesel is a good fuel to diesel engines due to its lubricity. Then, the aimed of this study was to verify the physicalchemistry properties of biodiesel and their correlations with possible elastomers damage after biodiesel be used as fuel in an injection system. The methodology was divided in three steps: biodiesels synthesis by transesterification of three vegetable oil (soybean, palm and sunflower) and their physical-chemistry characterization (viscosity, oxidative stability, flash point, acidity, humidity and density); pressurized test of compatibility between elastomers (NBR and VITON) and biodiesel, and the last one, analyze of biodiesels lubricity by tribological test ball-plan( HFRR). Also, the effect of mixture of biodiesel and diesel in different concentrations was evaluated. The results showed that VITON showed better compatibility with all biodiesel blends in relation to NBR, however when VITON had contact with sunflower biodiesel and its blends the swelling degree suffer higher influences due to biodiesel humidity. For others biodiesels and theirs blends, this elastomer kept its mechanical properties constant. The better tribological performance was observed for blends with high biodiesel concentration, lower friction coefficient was obtained when palm biodiesel was used. The main mechanisms observed during the HFRR tests were abrasive and oxidative wear

Emergência em campo de dicotiledôneas infestantes em solo coberto com palha de cana-de-açúcar

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Competitividade de diferentes atmosferas de plasma sobre as propriedades hidrofílicas em tecidos de polilático

Os polímeros biodegradáveis, como o poliácido láctico (PLA) apesar de consolidado nos campos farmacêuticos, médico e biomédico como biomateriais úteis para aplicações variadas, porém, depende da necessidade de funcionalizar a sua superfície estudando suas propriedades tais como hidrofilidade e hidrofobicidade favorecendo a interação do polímero com os materiais de aplicação farmacêutica, médica e biomédica. Este trabalho tem como objetivo produzir um material com características diferentes em cada um de seus lados, sendo um lado hidrofílico e o outro hidrofóbico. O substrato têxtil utilizado neste estudo foi um tecido de malha de composição 100% PLA que é biodegradável e biocompatível, o que possibilita sua aplicação na área biomédica. Para modificação superficial foi utilizado o tratamento a plasma de baixa pressão. A técnica de modificação de superfície por plasma foi escolhida por ser uma tecnologia limpa, anticorrosiva e não tóxica ao contrario de muitos processos químicos convencionais utilizados na indústria têxtil, além disso, não afeta as propriedades de massa do substrato. Neste estudo, um lado da superfície do substrato foi tratado com plasma oxigênio, argônio e nitrogênio, para o trabalho de melhoria da hidrofilidade da superfície e metano para a hidrofobicidade da amostra. A espectroscopia de emissão ótica (OEE) foi utilizada para fazer o diagnóstico das espécies do plasma durante o tratamento. Após o tratamento a plasma as amostras foram caracterizadas por medidas de ângulo de contato, microscopia eletrônica de varredura (MEV), Espectroscopia de fotoelétrons de raios-X (XPS), Infravermelho com Transformada de Fourier (FTIR) de reflexão total atenuada (ATR), medidas da área de espalhamento do líquido e arraste vertical. Onde foi caracterizado o aumento e diminuição da molhabilidade das amostras tratadas por plasma bem como as variáveis que contribuíram para tal efeito. O tratamento das amostras de PLA com O2 + CH4 apresenta comportamento hidrofílico no lado tratado com O2, apresentando aumento de rugosidade e grupos funcionais e no lado tratado com CH4, apresentando a formação de um filme polimérico formado sobre a superfície da amostra. O tratamento com N2 + CH4 apresenta comportamento hidrofóbico, porém com variações no fluxo do CH4 tem-se um controle da molhabilidade na superfície das amostras, podendo ir de hidrofóbico a hidrofílico, neste tratamento as amostras apresentaram pequenas diferenças de molhabilidade entre os lados tratados com plasma de N2 e com plasma de CH4

Seletividade de herbicidas aplicados em pré-emergência na cultura de cana-de-açúcar tratada com nematicidas

O objetivo do trabalho foi estudar a seletividade de herbicidas para a cultura da cana-de-açúcar quando aplicado em culturas tratadas com nematicidas. O experimento foi instalado em área pertencente à Usina São José, município de Borebi-SP, ano agrícola de 2000/01. A variedade de cana-de-açúcar utilizada foi a RB855113. Utilizou-se o delineamento experimental de blocos ao acaso em parcelas subdivididas, com quatro repetições. Cada parcela correspondeu a 27 linhas de 10,0 m, espaçadas em 1,0 m, sendo dividida em três subparcelas. As parcelas corresponderam aos tratamentos com os herbicidas, e as subparcelas, à aplicação ou não dos nematicidas carbofuran (2,10 kg ha-1) e terbufós 2,25 kg ha¹). Os herbicidas testados foram: tebuthiuron (1,12 kg ha-1), ametryne (1,75 kg ha¹), sulfentrazone (0,8 kg ha-1), metribuzin (1,92 kg ha-1), isoxaflutole (0,0525 kg ha¹), clomazone (1,25 kg ha¹), oxyfluorfen (0,36 kg ha-1) e azafenidin+hexazinone (0,1575 + 0,2025 kg ha-1), sendo todos aplicados em pré-emergência, além de uma parcela como testemunha. Os resultados obtidos evidenciaram que os herbicidas oxyfluorfen e azafenidin+hexazinone causaram os maiores níveis de fitotoxicidade na cana-de-açúcar, independentemente do uso dos nematicidas carbofuran e terbufós. Os herbicidas tebuthiuron, ametryne, sulfentrazone, metribuzin, isoxaflutole, clomazone, oxyfluorfen e azafenidin+hexazinone, aplicados em doses representativas das comercialmente utilizadas, mostraram-se seletivos à cana-de-açúcar, não afetando seu crescimento, sua produtividade e suas características tecnológicas. Os nematicidas não interferiram nos níveis de intoxicação provocados pelos herbicidas utilizados na cultura.

Eficiência e seletividade dos herbicidas trifloxysulfuron-sodium + ametryne e hexazinone + diuron em função da tecnologia de aplicação e do manejo mecânico da palha de cana-de-açúcar na linha de plantio

Com objetivo de otimizar a utilização de trifloxysulfuron-sodium + ametryne e hexazinone + diuron em função da adoção de diferentes pontas de pulverização e manejo mecânico da palha de cana-de-açúcar na linha de plantio, dois experimentos foram conduzidos na Destilaria Parálcool S/A, localizada em Paraguaçu Paulista/SP. No experimento 1, 12 tratamentos foram estudados em esquema fatorial 2 x 2 x 3, com quatro repetições, contrastando a presença e ausência de palha da cana na linha de plantio; dos herbicidas trifloxysulfuron sodium + ametryne (37 + 1.463 g i.a. ha-1 e 0,2% v/v de Aterbane®) e hexazinone + diuron (330 + 1.170 g i.a. ha-1 e 0,2% v/v de Aterbane®) e das pontas de pulverização XR11002-VS (128 L ha-1), AI11002-VS (200 L ha-1) e TF-VP5 (310 L ha-1). No experimento 2, a deposição da calda de pulverização nas plantas de cana-de-açúcar e Digitaria horizontalis, gerada pelas interações entre herbicidas e pontas, foi monitorada utilizando-se solução traçadora constituída por corante FDC-1 + herbicida. Os resultados sugerem que a presença da palhada da cultura proporcionou controle excelente das espécies infestantes mesmo na ausência do tratamento herbicida. O controle químico de D. horizontalis (6 folhas até 1-2 perfilhos) e Brachiaria decumbens (2 a 6 folhas) apresentou-se eficiente (> 91%) nas linhas sem palha a partir dos 14 DAA (dias após aplicação) para os herbicidas e pontas de pulverização estudados. D. horizontalis foi mais rapidamente controlada aos 7 DAA pelo trifloxysulfuron-sodium + ametryne com a ponta AI11002-VS. Houve toxicidade até os 21 DAA, sendo esta mais intensa para os tratamentos com hexazinone + diuron associado com as pontas AI11002-VS e TF-VP5, em decorrência da maior deposição do herbicida nas folhas da cultura.