Studies on the adsorption property of NO on the Ni-based mixed oxide catalysts with Perovskite-like (ABO(3) and A(2)BO(4)) structure

The mixed oxides LaNiO3, La0.1Sr0.9NiO3, La2NiO4 and LaSrNiO4 with perovskite (ABO(3)) and related(A(2)BO(4)) structures were prepared and the adsorption property for NO and the catalytic activity for NO decomposition over these oxidse were also tested. The catalysts were characterized by means of BET surface measurement, chemical analysis, NO-TPD etc.. It was shown that the adsorption amount of NO is correlated with the concentration of oxygen vacancy formed and the adsorption type and strength of NO are related to the valence of metallic ion. Generally there are three kinds of adsorption species, NO-, NO+ and NO on the mixed oxides, among them the negative adsorpion species (NO-) are active for NO decomposition. The weaker the adsorption of oxygen on the catalyst is, the faster the mobility of oxygen is and the easier the redox process takes place in reproducing the active sites in which the oxygen species (O-, O2-) would participate.

KINETIC-STUDY OF ELECTROCATALYTIC REDUCTION OF HYDROGEN-PEROXIDE AT IRON(III) PORPHYRIN MODIFIED GLASSY-CARBON ELECTRODE IN ALKALINE-MEDIUM USING THE ROTATION-SCAN METHOD

Reduction of hydrogen peroxide at a glassy carbon (GC) electrode modified with sigma-bonded pyrrole iron(III) octaethylporphyrin complex, (OEP)Fe(Pyr), was studied by cyclic voltammetry and a rotating disk electrode. In 0.1N NaOH solution, it is shown that such an (OEP)Fe(Pyr)/GC electrode has a significant catalytic activity towards hydrogen peroxide reduction (E(D) = -0.80 V, k = 0.066 cm s(-1)); however, the electrode stability is low. The deactivation is observed when the reaction charge (Q) is passing through the (OEP)Fe(Pyr)/GC disk electrode. A linear rotation scan method is applied to study the kinetic process by determining the disk electrochemical response (i(D)) to rotation rate (omega) at a definite disk potential (E(D)). Considering that the number of adsorbed electroreduced catalyst molecules (Red) varies according to the disk potential, a factor theta(= Gamma(Red)/(Gamma(Red) + Gamma(Ox))) is introduced to describe the electrode surface area fraction for electroreduced species. The obtained Koutecky-Levich equation is applicable whatever the potential is.

POLYMERIZATION OF ACRYLONITRILE INITIATED BY DI(2,6-DI-TERT-BUTYL-4-METHYLPHENOXO) SAMARIUM COMPLEX

The polymerization of acrylonitrile initiated by organolanthanide complexes alone is studied for the first time. The effect df polymerization conditions on catalytic activity of the title complex and molecular weight of the polymers produced have been studied.

STUDIES ON THE PEROVSKITE-TYPE MIXED CATALYSTS OF TITANIUM SYSTEM FOR OXIDATIVE COUPLING OF METHANE - THE INFLUENCE OF CALCINATION TEMPERATURE

The correlations of the calcination temperature, structure and catalytic activity for the oxidative coupling of methane on the LiLa0.5Ti0.5O2+lambda catalysts whose main phase and major active phase is Perovskite-type ternary complex oxide LaTi1-yLiyO3-lambda have been studied. The surface and bulk structures of the catalysts were characterized by means of XRD, XPS, IR, BET and so on, The results cleary indicated that the effect of calcination temperature on the activity for the oxidative coupling of methane is twofold. On one hand, it is favorable for Li+ substitution for Ti3+ to enter into the lattice of LaTiO3 and produce more oxygen vacancies in which active oxygens are formed; however, excessively high calcination temperature make the amount of Li+ substitution for Ti3+ lower, due to a little change of structure or phases for the catalyst. On the other hand, the conversion of CH4 drops because of the decrease of surface area, when the calcination temperature is raised.

A STUDY OF SURFACE OXYGEN SPECIES FROM LA-ME-O (ME=MG, CA, SR, BA) CATALYSTS FOR METHANE OXIDATIVE COUPLING

CO2-TPD was used to study the surface basicity of La-Me-O mixed oxides and O-2-TPD, CH4-TPD were employed to study the surface active oxygen species. Comparing the CO2-TPD with O-2-TPD, we can see that the basicity of catalyst is in parallel with the catalystic activity. The stronger basicity is more profitable for the catalyst to adsorb oxygen to form active oxygen species and to activate CH4 by breaking a C-H bond, By comparing the catalytic activity, the results showed that La-Ba-O(La/Ba=7/3) catalyst had the strongest basicity, and it gave the highest CH4 conversion and C-2 selectivity, The results from the pulse reaction showed that the lattice oxygen participated in the OCM reaction without gas oxygen, and it was the selective oxygen species.

Study of Methane Oxidative Coupling over Ti-La-Li Mixed Oxides

The composition and structures of Li-Ti-La mixed oxides as well as their catalytic activity for methane oxidative coupling have been studied by means of XRD XPS, IR, SEM and so on. The results indicate that by changing x value in Li-La1-xTixO2 oxides phas

SYNTHESIS AND CHARACTERIZATION OF POLYMER-SUPPORTED LANTHANIDE COMPLEXES AND BUTADIENE POLYMERIZATION BASED ON THEM

Poly(styrene-acrylic acid)-lanthanide (Ln.PSAA) and poly(ethylene-acrylic acid)-neodymium (NdPEAA) complexes have been prepared and characterized. The infrared and X-ray photoelectron spectra indicate that the lanthanide complexes possess the bidentate carboxylate structure Ln-O-C(R)-O (see structure B in text). The catalytic behavior of the complexes has been described. The catalytic activities of Nd.PSAA and Nd.PEAA are much greater than that of the corresponding low molecular weight catalyst for butadiene polymerization. The activities of various individual lanthanide elements are quite different from one another. Neodymium shows the highest activity. Europium, samarium and the heavy elements exhibit very low or no activities. The cis-1,4 content of the polybutadiene obtained is not affected by different lanthanide elements in the series. The complex with the intermediate content of the functional group has a higher activity than the others. The polymer-supported lanthanide complexes having different constitutions have different catalytic activities. When the molar ratio of lanthanide to the functional group is ca. 0.2, the activity of the complex is in the optimum state. The activity is influenced by the dispersion of the lanthanide metal immobilized on the polymer chain. Catalytic activity can be improved by adding other metals to the catalyst system.

RAPID-DETERMINATION OF KINETIC-PARAMETERS FOR THE ELECTROCATALYTIC REDUCTION OF DIOXYGEN BY VITAMIN-B12 ADSORBED ON GLASSY-CARBON ELECTRODE

In this paper, the electrochemical behavior of vitamin B-12, ie cyanocobalamin (abbr. VB12) in a weak acidic aqueous solution and adsorbed on glassy carbon (GC) surface (abbr. VB12(ad)/GC) in different pH buffer solutions have been described by using cyclic voltammetry (cv). It is found that VB12 and VB12(ad)/GC exhibit catalytic activity for the electroreduction of O2 according to two reduction peaks at -0.50 and -1.00 V vs. sce; but their electrocatalytic activity is very unstable. Based on the method of hydrodynamic amperometry [B. Miller and S. Bruckenstein, J. electrochem. Soc. 117, 1033 (1970)], some kinetic parameters for the electrocatalytic reduction of O2 by VB12(ad)/GC have been determined rapidly by using a linear rotation-scan method [Rongzhong Jiang and Shaojun Dong, Electrochim. Acta 35, 1451 (1990)]. These kinetic parameters indicate that the reduction of O2 on VB12(ad)/GC gives water predominantly in both potential ranges which correspond to those two reduction peaks. Possible reaction mechanisms have been suggested.

SYNTHESIS, PROPERTIES AND MOLECULAR-STRUCTURE OF 5-COORDINATE N,N-DIBENZYLDITHIOCARBAMATE COMPLEXES OF TITANOCENE, ZIRCONOCENE AND HAFNOCENE

The five complexes (RC5H4)2M(S2CNBz2)Cl (R = H, CH3; M = Ti, Zr, Hf; Bz = CH2C6H5) have been prepared by the reaction of (RC5H4)2MCl2 with anhydrous sodium salts of dibenzyldithiocarbamate in refluxing CH2Cl2. These complexes have been characterized by elemental analysis, IR and H-1 NMR. X-ray crystal structure determination of Cp2Zr(S2CNBZ2)Cl shows the molecule has a five-coordinate bent metallocene geometry in which the zirconium atom is attached to two eta-5-C5H5 groups, one bidentate dibenzyldithiocarbamate ligand and one chlorine [Zr-Cl, 2.549(1) angstrom; Zr-S, 2.734(1), 2.667(1); Cl-Zr-S, 137.6(1)-degrees and 73.3(1)-degrees; S-Zr-S, 64.3(1)-degrees]. The catalytic system Cp2Ti (S2CNBZ2)Cl-NaH exhibits high initial catalytic activity of hydrogenation of hexene-1 under mild conditions.

SYNTHESIS OF ALKALI-METAL HYDRIDES USING LANTHANIDE TRICHLORIDE-NAPHTHALENE AS CATALYST UNDER MILD CONDITIONS

The hydrogenation of alkali metals using lanthanide trichloride and naphthalene as catalyst has been studied. LnCl3(Ln = La, Nd, Sm, Dy, Yb) and naphthalene can catalyze the hydrogenation of sodium under atmospheric pressure and 40-degrees-C to form sodium hydride. The activities of lanthanide trichlorides are in the following order: LaCl3 > NdCl3 > SmCl3 > DyCl3 > YbCl3. Although lithium proceeds in the same catalytic reaction, the kinetic curve of the lithium hydrogenation is different from that of sodium. Lanthanide trichlorides display no catalytic effect on the hydrogenation of potassium in presence of naphthalene. The mechanism of this reaction has been studied and it is suggested that the anion-radical of alkali metal naphthalene complexes may be the intermediate for the hydrogenation of alkali metals and the function of LnCl3 is to catalyze the hydrogenation of the intermediate. The products are porous solids with high specific surface area (83 m2/g for NaH) and pyrophoric in air. They are far more active than the commercial alkali metal hydrides. The combination of these hydrides with some transition metal complexes exhibits high catalytic activity for the hydrogenation of olefins.

Direct synthesis and characterization of titanium-substituted mesoporous molecular sieve SBA-15

Ti-substituted mesoporous SBA-15 (Ti-SBA-15) materials have been synthesized by using a new approach in which the hydrolysis of the silicon precursor (tetramethoxysilane, TMOS) is accelerated by fluoride. These materials were characterized by powder X-ray diffraction patterns (XRD), X-ray fluorescence spectroscopy (Y-RF), N-2 sorption isotherms, diffuse-reflectance UV-visible (UV-vis) and UV-Raman spectroscopy, Si-29 MAS NMR, and the catalytic epoxidation reaction of styrene. Experiments show that Ti-SBA-15 samples of high quality can be obtained under the following conditions: F/Si greater than or equal to 0.03 (molar ratio), pH less than or equal to 1.0, aging temperature less than or equal to 80 degreesC, and Ti/Si less than or equal to 0.01. It was found that the hydrolysis rate of TMOS was remarkably accelerated by fluoride, which was suggested to play the main role in the formation of Ti-SBA-15 materials of high quality. There is no stoichiometric incorporation of Ti, and the Ti contents that are obtained are quite low in the case of the approach that is proposed. The calcined Ti-SBA-15 materials show highly catalytic activity in the epoxidation of styrene.

Synergetic effect between NiO and Ni3V2O8 in propane oxidative dehydrogenation

The oxidative dehydrogenation (ODH) of propane was investigated on Ni-V-O catalysts in a wide range of vanadium contents (5-40%). The addition of a small amount of vanadium significantly increased the catalytic activity of NiO for oxidative dehydrogenation of propane to propene. The formation of propene has a good correlation with the coexistence of NiO and Ni3V2O8. This result strongly suggests that a synergetic effect exists between them in NiXV1-XOY (X = 0.95 to 0.6). The best results were obtained with a high Ni/V ratio (e.g. X = 0.95 to 0.85). The active sites and selective oxygen species are discussed. The influence of the catalyst preparation technique and the redox properties of the catalyst were also examined.

The effect of additives on Cu/HZSM-5 catalyst for DME synthesis

The addition of ZnO or ZrO2 into CuO/HZSM-5 was investigated for DME synthesis from syngas by using the reactive frontal chromatography method, TPR and in situ TPR. These promoters enhanced the catalytic activity of Cu/HZSM-5 and promotion with ZnO and ZrO2 produced a maximum activity, which could be explained by the improvement of the dispersion of Cu and the promotion of CuO reduction. The Cu+ species existing during the reaction have been detected, based on which a Cu-0 <-> Cu+1 redox cycle model was put forward.

Epoxidation of cyclohexene on Ti/SiO2 catalysts prepared by chemical grafting TiCl4 on deboronated silica xerogel

Ti/SiO2 (or Ti/de[B]SiO2) catalysts were prepared by grafting deboronated silica xerogel with gaseous TiCl4. Using TBHP as oxidant, the Ti/de[B]SiO2 catalyst shows both catalytic activity and selectivity in epoxidation of cyclohexene better than 80%, and the activity can be comparable with that of Ti-beta. The catalytic activity of Ti/de[B]SiO2 strongly depends on the content of B of support precursor, and the pretreatment temperature of the support. IR studies show that the sites in the deboronated silica xerogel to react with TiCl4 are not only the silanol nests, but also the defect sites produced during the deboronation. (C) 2001 Elsevier Science B.V. All rights reserved.

A remarkable synergic effect of water-soluble bimetallic catalyst in the hydrogenation of aromatic nitrocompounds

Hydrogenation of nitrobenzene can be catalyzed by the water-soluble catalyst PdCl2(TPPTS)(2) (TPPTS = tris(m-sulfonatophenyl)phosphine trisodium salt) under normal pressure at 65 degrees C in H2O/toluene biphasic solvent system. The exhibits higher catalytic activity and selectivity for the hydrogenation of aromatic nitrocompounds, compared with PdCl2(TPPTS)(2) or H2PtCl6 alone. The transmission electron micrographs demonstrate that the monometallic catalyst is composed of ultrafine palladium particles of almost uniform size while the particles of bimetallic catalyst are more widely distributed in size than those of the monometallic ones. (C) 1999 Elsevier Science B.V. All rights reserved.