Stress corrosion crack propagation in AerMet 100

Fracture mechanics tests were carried out for AerMet 100 in distilled water and NaCl (3.5 and 35 gl(-1)). The initiation period at higher values of the stress intensity factor indicated that load application in the stress corrosion cracking (SCC) environment is a necessary but not sufficient factor for SCC and that time is needed for some other factor (e.g., the local hydrogen concentration) to reach an appropriate value. The threshold stress intensity factor, K-ISSC, was found to increase with decreasing NaCl concentration. The plateau stress corrosion crack velocity was 2 x 10(-8) ms(-1) for NaCl (3.5 and 35 gl(-1)). The fracture mode was transgranular with small areas of an intergranular nature. (C) 1998 Chapman & Hall.

Matrix elements of U(2n) generators in a multishell spin-orbit basis. I. The del-operator MEs in a two-shell composite Gelfand-Paldus basis

This is the first in a series of three articles which aimed to derive the matrix elements of the U(2n) generators in a multishell spin-orbit basis. This is a basis appropriate to many-electron systems which have a natural partitioning of the orbital space and where also spin-dependent terms are included in the Hamiltonian. The method is based on a new spin-dependent unitary group approach to the many-electron correlation problem due to Gould and Paldus [M. D. Gould and J. Paldus, J. Chem. Phys. 92, 7394, (1990)]. In this approach, the matrix elements of the U(2n) generators in the U(n) x U(2)-adapted electronic Gelfand basis are determined by the matrix elements of a single Ll(n) adjoint tensor operator called the del-operator, denoted by Delta(j)(i) (1 less than or equal to i, j less than or equal to n). Delta or del is a polynomial of degree two in the U(n) matrix E = [E-j(i)]. The approach of Gould and Paldus is based on the transformation properties of the U(2n) generators as an adjoint tensor operator of U(n) x U(2) and application of the Wigner-Eckart theorem. Hence, to generalize this approach, we need to obtain formulas for the complete set of adjoint coupling coefficients for the two-shell composite Gelfand-Paldus basis. The nonzero shift coefficients are uniquely determined and may he evaluated by the methods of Gould et al. [see the above reference]. In this article, we define zero-shift adjoint coupling coefficients for the two-shell composite Gelfand-Paldus basis which are appropriate to the many-electron problem. By definition, these are proportional to the corresponding two-shell del-operator matrix elements, and it is shown that the Racah factorization lemma applies. Formulas for these coefficients are then obtained by application of the Racah factorization lemma. The zero-shift adjoint reduced Wigner coefficients required for this procedure are evaluated first. All these coefficients are needed later for the multishell case, which leads directly to the two-shell del-operator matrix elements. Finally, we discuss an application to charge and spin densities in a two-shell molecular system. (C) 1998 John Wiley & Sons.

Matrix elements of U(2n) generators in a multishell spin-orbit basis. III. General formulas

This is the third and final article in a series directed toward the evaluation of the U(2n) generator matrix elements (MEs) in a multishell spin/orbit basis. Such a basis is required for many-electron systems possessing a partitioned orbital space and where spin-dependence is important. The approach taken is based on the transformation properties of the U(2n) generators as an adjoint tensor operator of U(n) x U(2) and application of the Wigner-Eckart theorem. A complete set of adjoint coupling coefficients for the two-shell composite Gelfand-Paldus basis (which is appropriate to the many-electron problem) were obtained in the first and second articles of this series. Ln the first article we defined zero-shift coupling coefficients. These are proportional to the corresponding two-shell del-operator matrix elements. See P. J. Burton and and M. D. Gould, J. Chem. Phys., 104, 5112 (1996), for a discussion of the del-operator and its properties. Ln the second article of the series, the nonzero shift coupling coefficients were derived. Having obtained all the necessary coefficients, we now apply the formalism developed above to obtain the U(2n) generator MEs in a multishell spin-orbit basis. The methods used are based on the work of Gould et al. (see the above reference). (C) 1998 John Wiley & Sons, Inc.

The treatment of tardive dyskinesia: A systematic review and meta-analysis

This systematic review aimed to collate randomized controlled trials (RCTs) of various interventions used to treat tardive dyskinesia (TD) and, where appropriate, to combine the data for mete-analysis, Clinical trials were identified by electronic searches, handsearches and contact with principal investigators. Data were extracted independently by two reviewers, for outcomes related to improvement, deterioration, side-effects and drop out rates. Data were pooled using the Mantel-Haenzel Odds Ratio (fixed effect model). For treatments that had significant effects, the number needed to treat (NNT) was calculated. From 296 controlled clinical trials, data were extracted from 47 trials. For most interventions, we could identify no RCT-derived evidence of efficacy. A meta-analysis showed that baclofen, deanol and diazepam were no more effective than a placebo. Single RCTs demonstrated a lack of evidence of any effect for bromocriptine, ceruletide, clonidine, estrogen, gamma linolenic acid, hydergine, lecithin, lithium, progabide, seligiline and tetrahydroisoxazolopyridinol. The meta-analysis found that five interventions were effective: L-dopa, oxypertine, sodium valproate, tiapride and vitamin E; neuroleptic reduction was marginally significant. Data from single RCTs revealed that insulin, alpha methyl dopa and reserpine were more effective than a placebo. There was a significantly increased risk of adverse events associated with baclofen, deanol, L-dopa, oxypertine and reserpine. Metaanalysis of the impact of placebo (n=485) showed that 37.3% of participants showed an improvement. Interpretation of this systematic review requires caution as the individual trials identified tended to have small sample sizes. For many compounds, data from only one trial were available, and where meta-analyses were possible, these were based on a small number of trials. Despite these concerns, the review facilitated the interpretation of the large and diverse range of treatments used for TD. Clinical recommendations for the treatment of TD are made, based on the availability of RCT-derived evidence, the strength of that evidence and the presence of adverse effects. (C) 1999 Elsevier Science B.V. All rights reserved.

Improved methods for predicting individual leaf area and leaf senescence in maize (Zea mays)

The ability to predict leaf area and leaf area index is crucial in crop simulation models that predict crop growth and yield. Previous studies have shown existing methods of predicting leaf area to be inadequate when applied to a broad range of cultivars with different numbers of leaves. The objectives of the study were to (i) develop generalised methods of modelling individual and total plant leaf area, and leaf senescence, that do not require constants that are specific to environments and/or genotypes, (ii) re-examine the base, optimum, and maximum temperatures for calculation of thermal time for leaf senescence, and (iii) assess the method of calculation of individual leaf area from leaf length and leaf width in experimental work. Five cultivars of maize differing widely in maturity and adaptation were planted in October 1994 in south-eastern Queensland, and grown under non-limiting conditions of water and plant nutrient supplies. Additional data for maize plants with low total leaf number (12-17) grown at Katumani Research Centre, Kenya, were included to extend the range in the total leaf number per plant. The equation for the modified (slightly skewed) bell curve could be generalised for modelling individual leaf area, as all coefficients in it were related to total leaf number. Use of coefficients for individual genotypes can be avoided, and individual and total plant leaf area can be calculated from total leaf number. A single, logistic equation, relying on maximum plant leaf area and thermal time from emergence, was developed to predict leaf senescence. The base, optimum, and maximum temperatures for calculation of thermal time for leaf senescence were 8, 34, and 40 degrees C, and apply for the whole crop-cycle when used in modelling of leaf senescence. Thus, the modelling of leaf production and senescence is simplified, improved, and generalised. Consequently, the modelling of leaf area index (LAI) and variables that rely on LAI will be improved. For experimental purposes, we found that the calculation of leaf area from leaf length and leaf width remains appropriate, though the relationship differed slightly from previously published equations.

Synthesis, NMR studies and conformational analysis of oxazolidine derivatives of the beta-adrenoreceptor antagonists metoprolol, atenolol and timolol

Formaldehyde-derived oxazolidine derivatives 4-7 of the beta-adrenoreceptor antagonists metoprolol 1, atenolol 2 and timolol 3 have been synthesised. Conformational analysis of 1-3 and the oxazolidine derivatives 4-7 has been performed using H-1 NMR spectroscopy and computational methods. The H-1 NMR studies show that for the aryloxypropanolamine beta-adrenoreceptor antagonists there is a predominance of the conformer in which the amine group is approximately antiperiplanar or trans to the aryloxymethylene group. Both H-1 NMR data and theoretical studies indicate that the oxazolidine derivatives 4-7 and the aryloxypropanolamine beta-adrenoreceptor antagonists 1-3 adopt similar conformations around the beta-amino alcohol moiety. Thus, oxazolidine ring formation does not dramatically alter the preferred conformation adopted by the beta-amino alcohol moiety of 1-3. Oxazolidine derivatives of aryloxypropanolamine beta-adrenoreceptor antagonists may therefore be appropriate as prodrugs, or semi-rigid analogues, when greater lipophilicity is required for drug delivery.

Distribution of transferrin saturation in an Australian population: Relevance to the early diagnosis of hemochromatosis

Background & Aims: An elevated transferrin saturation is the earliest phenotypic abnormality in hereditary hemochromatosis. Determination of transferrin saturation remains the most useful noninvasive screening test for affected individuals, but there is debate as to the appropriate screening level. The aims of this study were to estimate the mean transferrin saturation in hemochromatosis heterozygotes and normal individuals and to evaluate potential transferrin saturation screening levels. Methods: Statistical mixture modeling was applied to data from a survey of asymptomatic Australians to estimate the mean transferrin saturation in hemochromatosis heterozygotes and normal individuals. To evaluate potential transferrin saturation screening levels, modeling results were compared with data from identified hemochromatosis heterozygotes and homozygotes. Results: After removal of hemochromatosis homozygotes, two populations of transferrin saturation were identified in asymptomatic Australians (P < 0.01). In men, 88.2% of the truncated sample had a lower mean transferrin saturation of 24.1%, whereas 11.8% had an increased mean transferrin saturation of 37.3%. Similar results were found in women, A transferrin saturation threshold of 45% identified 98% of homozygotes without misidentifying any normal individuals. Conclusions: The results confirm that hemochromatosis heterozygotes form a distinct transferrin saturation subpopulation and support the use of transferrin saturation as an inexpensive screening test for hemochromatosis. In practice, a fasting transferrin saturation of greater than or equal to 45% identifies virtually all affected homozygous subjects without necessitating further investigation of unaffected normal individuals.

Preeruptive intracoronal radiolucencies: Review and report of case

Intracoronal radiolucencies in unerupted teeth are an uncommon radiographic finding; but their early detection and classification allow the most appropriate management protocol to be developed. Early separation of lesions into those that are developmental and remain static and those that are reactive and aggressive is necessary for a controlled outcome. The current paper reviews possible formative mechanisms and describes a case of severe intracoronal resorption resulting in loss of the tooth.

Ester prodrugs of a potent analgesic, morphine-6-sulfate: syntheses, spectroscopic and physicochemical properties

The aim of this work is to develop 3-acyl prodrugs of the potent analgesic morphine-6-sulfate (M6S). These are expected to have higher potency and/or exhibit longer duration of analgesic action than the parent compound. M6S and the prodrugs were synthesized, then purified either by recrystallization or by semi-preparative HPLC and the structures confirmed by mass spectrometry, IR spectrophotometry and by detailed 1- and 2-D NMR studies. The lipophilicities of the compounds were assessed by a combination of shake-flask, group contribution and HPLC retention methods. The octanol-buffer partition coefficient could only be obtained directly for 3-heptanoylmorphine-6-sulfate, using the shake-flask method. The partition coefficients (P) for the remaining prodrugs were estimated from known methylene group contributions. A good linear relationship between log P and the HPLC log capacity factors was demonstrated. Hydrolysis of the 3-acetyl prodrug, as a representative of the group, was found to occur relatively slowly in buffers (pH range 6.15-8.01), with a small buffer catalysis contribution. The rates of enzymatic hydrolysis of the 3-acyl group in 10% rat blood and in 10% rat brain homogenate were investigated. The prodrugs followed apparent first order hydrolysis kinetics, with a significantly faster hydrolysis rate found in 10% rat brain homogenate than in 10% rat blood for all compounds. (C) 1998 Elsevier Science B.V. All rights reserved.

Classical and quantum noise in electronic systems

We review the description of noise in electronic circuits in terms of electron transport. The Poisson process is used as a unifying principle. In recent years, much attention has been given to current noise in light-emitting diodes and laser diodes. In these devices, random events associated with electron transport are correlated with photon emission times, thus modifying both the current statistics and the statistics of the emitted light. We give a review of experiments in this area with special emphasis on the ability of such devices to produce subshot-noise currents and light beams. Finally we consider the noise properties of a class of mesoscopic devices based on the quantum tunnelling of an electron into and out of a bound state. We present a simple quantum model of this process which confirms that the current noise in such a device should be subshot-noise.

A study of the stability of subcycling algorithms in structural dynamics

Algorithms for explicit integration of structural dynamics problems with multiple time steps (subcycling) are investigated. Only one such algorithm, due to Smolinski and Sleith has proved to be stable in a classical sense. A simplified version of this algorithm that retains its stability is presented. However, as with the original version, it can be shown to sacrifice accuracy to achieve stability. Another algorithm in use is shown to be only statistically stable, in that a probability of stability can be assigned if appropriate time step limits are observed. This probability improves rapidly with the number of degrees of freedom in a finite element model. The stability problems are shown to be a property of the central difference method itself, which is modified to give the subcycling algorithm. A related problem is shown to arise when a constraint equation in time is introduced into a time-continuous space-time finite element model. (C) 1998 Elsevier Science S.A.

What is a healthy weight for middle aged women?

OBJECTIVE: To explore associations between body mass index (BMI) and selected indicators of health and well-being and to suggest a healthy weight range (based on BMI) for middle aged Australian women. DESIGN: population based longitudinal study (cross-sectional baseline data). SUBJECTS: 13431 women aged 45-49 y who participated in the baseline survey for the Australian Longitudinal Study on Women's Health. RESULTS: Forty-eight percent of women had a BMI>25kg/m(2). Prevalence of medical problems (for example, hypertension, diabetes), surgical procedures (cholescystectomy, hysterectomy) and symptoms (for example, back pain) increased monotonically with BMI, while indicators of health care use (for example, visits to doctors) showed a 'J' shaped relationship with BMI. Scores for several sub-scales of the MOS short form health survey (SF36) (for example, general health, role limitations due to emotional difficulties, social function, mental health and vitality) were optimal when BMI was around 19-24 kg/m(2). After adjustment for area of residence, education, smoking, exercise and menopausal status, low BMI was associated with fewer physical health problems than mid-level or higher BMI, and the nationally recommended BMI range of 20-25 was associated with optimum mental health, lower prevalence of tiredness and lowest use of health services. CONCLUSIONS: Acknowledging the limitations of the cross-sectional nature of these data, the results firmly support the benefits of leanness in terms of reducing the risk of cardiovascular disease, diabetes and gall bladder disease. The findings are moderated, however, by the observation that both low and high BMI are associated with decreased vitality and poorer mental health. The optimal range for BMI appears to be about 19-24 kg/m(2). From a public health perspective this study provides strong support for the recommended BMI range of 20-25 as an appropriate target for the promotion of healthy weight in middle aged Australian women.

Subcycling first- and second-order generalizations of the trapezoidal rule

Subcycling algorithms which employ multiple timesteps have been previously proposed for explicit direct integration of first- and second-order systems of equations arising in finite element analysis, as well as for integration using explicit/implicit partitions of a model. The author has recently extended this work to implicit/implicit multi-timestep partitions of both first- and second-order systems. In this paper, improved algorithms for multi-timestep implicit integration are introduced, that overcome some weaknesses of those proposed previously. In particular, in the second-order case, improved stability is obtained. Some of the energy conservation properties of the Newmark family of algorithms are shown to be preserved in the new multi-timestep extensions of the Newmark method. In the first-order case, the generalized trapezoidal rule is extended to multiple timesteps, in a simple way that permits an implicit/implicit partition. Explicit special cases of the present algorithms exist. These are compared to algorithms proposed previously. (C) 1998 John Wiley & Sons, Ltd.

The development of an early warning system to detect trends in illicit drug use in Australia: The illicit drug reporting-system

Appropriate ways to monitor the availability and use of illicit drugs were examined. Four methods were tested concurrently: (1) a quantitative survey of injecting drug users, (2) a qualitative key informant study of illicit drug users and professionals working in the drug field, (3) examination of existing sources of survey, health and law enforcement data and (4) an ethnographic study of a high risk group of illicit drug users. The first three methods were recommended for inclusion in an ongoing national monitoring system, enabling the collection of both quantitative and qualitative data on a range of illicit drugs in a relatively brief, quick and cost-effective manner. A degree of convergent validity was also noted among these methods, improving the degree of confidence in drug trends. The importance of injecting drug users as a sentinel population of illicit drug users was highlighted, along with optimal methods for qualitative research.

Kinetic analysis of vascular marker distribution in perfused rat livers after regeneration following partial hepatectomy

Background/Aims: Liver clearance models are based on information (or assumptions) on solute distribution kinetics within the microvasculatory system, The aim was to study albumin distribution kinetics in regenerated livers and in livers of normal adult rats, Methods: A novel mathematical model was used to evaluate the distribution space and the transit time dispersion of albumin in livers following regeneration after a two-thirds hepatectomy compared to livers of normal adult rats. Outflow curves of albumin measured after bolus injection in single-pass perfused rat livers were analyzed by correcting for the influence of catheters and fitting a long-tailed function to the data. Results: The curves were well described by the proposed model. The distribution volume and the transit time dispersion of albumin observed in the partial hepatectomy group were not significantly different from livers of normal adult rats. Conclusions: These findings suggest that the distribution space and the transit time dispersion of albumin (CV2) is relatively constant irrespective of the presence of rapid and extensive repair. This invariance of CV2 implies, as a first approximation, a similar degree of intrasinusoidal mixing, The finding that a sum of two (instead of one) inverse Gaussian densities is an appropriate empirical function to describe the outflow curve of vascular indicators has consequences for an improved prediction of hepatic solute extraction.