Fatigue crack propagation in nickel-base superalloys:effects of microstructure, load ratio, and temperature

The current state of knowledge and understanding of the long fatigue crack propagation behavior of nickel-base superalloys are reviewed, with particular emphasis on turbine disk materials. The data are presented in the form of crack growth rate versus stress intensity factor range curves, and the effects of such variables as microstructure, load ratio, and temperature in the near-threshold and Paris regimes of the curves, are discussed.

Effects of dynamic strain ageing on fatigue crack propagation and threshold behaviour in a Ni-base superalloy

In the temperature range 200-400 degree C the Ni-base superalloy, N901, develops marked dynamic strain ageing effects in its tensile behavior. These include inverse strain rate sensitivity, especially in UTS values, strongly serrated stress-strain curves and a heavily sheared failure mode at the higher test-temperatures. As for steels these effects seem to be due to interactions between the dislocations and the interstitial carbon atoms present. The results of tensile and fatigue threshold tests carried out between 20 degree C and 420 degree C are reported and the fatigue behavior is discussed in terms of the effects of surface roughness induced closure, temperature and strain aging interactions.

Effects of microstructure, temperature and R-ratio on fatigue crack propagation and threshold behaviour in two Ni-base alloys

Fatigue crack propagation and threshold data for two Ni-base alloys, Astroloy and Nimonic 901, are reported. At room temperature the effect which altering the load ratio (R-ratio) has on fatigue behaviour is strongly dependent on grain size. In the coarse grained microstructures crack growth rates increase and threshold values decrease markedly as R rises from 0. 1 to 0. 8, whereas only small changes in behaviour occur in fine grained material. In Astroloy, when strength level and gamma grain size are kept constant, there is very little effect of processing route and gamma prime distribution on room temperature threshold and crack propagation results. The dominant microstructural effect on this type of fatigue behaviour is the matrix ( gamma ) grain size itself.

Nonlinearity compensation via spectral inversion and digital back-propagation:a practical approach

We report performance enhancements enabled by pre-dispersed spectral inversion equivalent to that of ideal back-propagation, with further x2 increase in reach from multi-channel compensation, with spectral inversion employed upto 400km (from mid-link) with <1dB penalties. © 2012 OSA.

Proposal and design of airy-based rocket pulses for invariant propagation in lossy dispersive media

A novel kind of Airy-based pulse with an invariant propagation in lossy dispersive media is proposed. The basic principle is based on an optical energy trade-off between different parts of the pulse caused by the chromatic dispersion, which is used to compensate the attenuation losses of the propagation medium. Although the ideal concept of the proposed pulses implies infinite pulse energy, the numerical simulations show that practical finite energy pulses can be designed to obtain a partially invariant propagation over a finite distance of propagation.

Unrepeatered Nyquist PDM-16QAM transmission over 364 km using Raman amplification and multi-channel digital back-propagation

Transmission of a net 467-Gb/s PDM-16QAM Nyquist-spaced superchannel is reported with an intra-superchannel net spectral efficiency (SE) of 6.6 (b/s)/Hz, over 364-km SMF-28 ULL ultra-low loss optical fiber, enabled by bi-directional second-order Raman amplification and digital nonlinearity compensation. Multi-channel digital back-propagation (MC-DBP) was applied to compensate for nonlinear interference; an improvement of 2 dB in Q2 factor was achieved when 70-GHz DBP bandwidth was applied, allowing an increase in span length of 37 km.

Integrated sensitivity analysis, calibration, and uncertainty propagation analysis approaches for supporting hydrological modeling

The successful performance of a hydrological model is usually challenged by the quality of the sensitivity analysis, calibration and uncertainty analysis carried out in the modeling exercise and subsequent simulation results. This is especially important under changing climatic conditions where there are more uncertainties associated with climate models and downscaling processes that increase the complexities of the hydrological modeling system. In response to these challenges and to improve the performance of the hydrological models under changing climatic conditions, this research proposed five new methods for supporting hydrological modeling. First, a design of experiment aided sensitivity analysis and parameterization (DOE-SAP) method was proposed to investigate the significant parameters and provide more reliable sensitivity analysis for improving parameterization during hydrological modeling. The better calibration results along with the advanced sensitivity analysis for significant parameters and their interactions were achieved in the case study. Second, a comprehensive uncertainty evaluation scheme was developed to evaluate three uncertainty analysis methods, the sequential uncertainty fitting version 2 (SUFI-2), generalized likelihood uncertainty estimation (GLUE) and Parameter solution (ParaSol) methods. The results showed that the SUFI-2 performed better than the other two methods based on calibration and uncertainty analysis results. The proposed evaluation scheme demonstrated that it is capable of selecting the most suitable uncertainty method for case studies. Third, a novel sequential multi-criteria based calibration and uncertainty analysis (SMC-CUA) method was proposed to improve the efficiency of calibration and uncertainty analysis and control the phenomenon of equifinality. The results showed that the SMC-CUA method was able to provide better uncertainty analysis results with high computational efficiency compared to the SUFI-2 and GLUE methods and control parameter uncertainty and the equifinality effect without sacrificing simulation performance. Fourth, an innovative response based statistical evaluation method (RESEM) was proposed for estimating the uncertainty propagated effects and providing long-term prediction for hydrological responses under changing climatic conditions. By using RESEM, the uncertainty propagated from statistical downscaling to hydrological modeling can be evaluated. Fifth, an integrated simulation-based evaluation system for uncertainty propagation analysis (ISES-UPA) was proposed for investigating the effects and contributions of different uncertainty components to the total propagated uncertainty from statistical downscaling. Using ISES-UPA, the uncertainty from statistical downscaling, uncertainty from hydrological modeling, and the total uncertainty from two uncertainty sources can be compared and quantified. The feasibility of all the methods has been tested using hypothetical and real-world case studies. The proposed methods can also be integrated as a hydrological modeling system to better support hydrological studies under changing climatic conditions. The results from the proposed integrated hydrological modeling system can be used as scientific references for decision makers to reduce the potential risk of damages caused by extreme events for long-term water resource management and planning.

Crack propagation in non-homogenous materials: Evaluation of mixed-mode SIFs, T-stress and kinking angle using a variant EFG method

A new variant of the Element-Free Galerkin (EFG) method, that combines the diffraction method, to characterize the crack tip solution, and the Heaviside enrichment function for representing discontinuity due to a crack, has been used to model crack propagation through non-homogenous materials. In the case of interface crack propagation, the kink angle is predicted by applying the maximum tangential principal stress (MTPS) criterion in conjunction with consideration of the energy release rate (ERR). The MTPS criterion is applied to the crack tip stress field described by both the stress intensity factor (SIF) and the T-stress, which are extracted using the interaction integral method. The proposed EFG method has been developed and applied for 2D case studies involving a crack in an orthotropic material, crack along an interface and a crack terminating at a bi-material interface, under mechanical or thermal loading; this is done to demonstrate the advantages and efficiency of the proposed methodology. The computed SIFs, T-stress and the predicted interface crack kink angles are compared with existing results in the literature and are found to be in good agreement. An example of crack growth through a particle-reinforced composite materials, which may involve crack meandering around the particle, is reported.

3D Ionospheric Effects on HF Propagation and Heating

The thesis uses a three-dimensional, first-principles model of the ionosphere in combination with High Frequency (HF) raytracing model to address key topics related to the physics of HF propagation and artificial ionospheric heating. In particular: 1. Explores the effect of the ubiquitous electron density gradients caused by Medium Scale Traveling Ionospheric Disturbances (MSTIDs) on high-angle of incidence HF radio wave propagation. Previous studies neglected the all-important presence of horizontal gradients in both the cross- and down-range directions, which refract the HF waves, significantly changing their path through the ionosphere. The physics-based ionosphere model SAMI3/ESF is used to generate a self-consistently evolving MSTID that allows for the examination of the spatio-temporal progression of the HF radio waves in the ionosphere. 2. Tests the potential and determines engineering requirements for ground- based high power HF heaters to trigger and control the evolution of Equatorial Spread F (ESF). Interference from ESF on radio wave propagation through the ionosphere remains a critical issue on HF systems reliability. Artificial HF heating has been shown to create plasma density cavities in the ionosphere similar to those that may trigger ESF bubbles. The work explores whether HF heating may trigger or control ESF bubbles. 3. Uses the combined ionosphere and HF raytracing models to create the first self-consistent HF Heating model. This model is utilized to simulate results from an Arecibo experiment and to provide understanding of the physical mechanism behind observed phenomena. The insights gained provide engineering guidance for new artificial heaters that are being built for use in low to middle latitude regions. In accomplishing the above topics: (i) I generated a model MSTID using the SAMI3/ESF code, and used a raytrace model to examine the effects of the MSTID gradients on radio wave propagation observables; (ii) I implemented a three- dimensional HF heating model in SAMI3/ESF and used the model to determine whether HF heating could artificially generate an ESF bubble; (iii) I created the first self-consistent model for artificial HF heating using the SAMI3/ESF ionosphere model and the MoJo raytrace model and ran a series of simulations that successfully modeled the results of early artificial heating experiments at Arecibo.

Bacterial and pathological study of caudal fin rot in brood stocks of Salmo trutta caspius from the propagation and breeding center of Shahid Bahonar of Kelardasht region

In order to study caudal fin rot with emphasis on Aeromonas hydrophila and Pseudomonas fluorescens in Salmo trutta caspius from the salmonids propagation and breeding center of Shahid Bahonar of kelardasht region, One hundred and eighty brood stocks having fin damage symptoms were chosen. Two bacterial samples from each fish were cultured on Aeromonas and Pseudomonas specific media. Biochemical tests, API2OE identification system and antibiogram test using six antibiotic disks were performed for diagnosing isolates bacteria and finding suitable antibiotic. Thirty samples from caudal fin of damaged fishes were fixed in 10% formalin and 51.tm microscopic sections were prepared using standard scatological methods and then stained by Haematoxylin-Eosin staining method to observe the pathological changes and also Maccallum-Goodpasture staining method to observe the bacterial colonies. In second stage of the study, bacterial samples were taken from thirty brood stocks using similar method at the first stage of sampling. For isolation and biochemical diagnosis of Aeromonas and Pseudormonas genus, the samples were analyzed by molecular research included PCR amplification (using 16S rDNA genes of the genus pseudomonas and 16S-23S rDNA intergenic spacer of the genus Aeromonas) and restriction analysis by four restriction enzymes for each genus. The results of biochemical tests showed that isolated bacteria were belonged to Aeromonas caviae and Aeromonas hydrophila (subspecies anaerogenes), Pseudomonas fluorescens, Pseudomonas putida and Pseudomonas alcaligenes while the results of API2OE identification system showed that the isolated bacteria belonged to Aeromonas hydrophila, Pseudomonas fluorescens, Pseudomonas putida and Pseudomonas aeruginosa. Restriction analysis of Aeromonas samples with Hin6l, Csp6I, Taql, and Tasl revealed three samples were different from others while restriction analysis of Pseudomonas samples with Alul, Hinfl, Rsal, and Trull showed at least five species or biovars. The results of antibiogram test showed all Aeromonas samples were sensitive to Trimethoprim, Chloramphenicol and Nitrofurazone, mostly to Nalidixic acid and Chloramphenicol, while most of samples were resistant to Erythromycin and Oxytetracycline. Pseudomonas samples were only sensitive to Nitrofurazone and mostly resistant to Oxytetracycline, Nalidixic acid, Erythromycin, Trimethoprim and Chloramphenicol. The results of light microscope study showed hyperplasia and spongiosis of the malpigian cells of epidermis, increasing of melanin pigments underlying epidermis; sever necrosis in both epidermis and dermis and also sloughing the epidermis in some cases. Occurrence of clefts through the epithelium, neovascularization, hyperemia and mild inflammatory response in dermis and separation of the fin rays also were observed. No bacterial colonies were found in the sections.

Seed and vegetative propagation methods for the rare Florida native species Chionanthus pygmaeus (pygmy fringetree)

Chionanthus pygmaeus Small (pygmy fringetree) (Oleaceae) is an endemic and rare Florida species, which has an attractive, small habit giving it great potential for use in managed landscapes. Members of the genus Chionanthus are difficult to propagate via cuttings and possess complex seed dormancies that are not well understood. Conservation of pygmy fringetree and its potential for commercial propagation for use in managed landscapes is contingent on a better understanding of its complex seed dormancy and enhancement of its propagation. I conducted two experiments to assess sexual and asexual propagation methods for pygmy fringetree. The first experiment was conducted to determine what factors are involved in overcoming seed dormancy. Various scarification treatments, which mimicked conditions seeds are exposed to in the wild, were investigated to determine their effects on germination of 20-year-old seeds originally collected from the species’ native range. Treatments included endocarp removal, sulfuric acid, boiling-water, and smoke-water treatments. Prior to treatment initiation, seed viability was estimated to be 12%. Treated seeds went through two cold- and two warm-stratification periods of 4°C and 25°C, respectively, in a dark growth chamber. After 180 days, none of the treatments induced early germination. Seeds were then tested for viability, which was 11%. Seed dormancy of the species is apparently complex, allowing some of the seeds to retain some degree of viability, but without dormancy requirements satisfied. The second experiment was conducted to assess if pygmy fringetree could be successfully propagated via hardwood or root cuttings if the appropriate combination of environmental conditions and hormones were applied. Hardwood and root cuttings were treated with either 1000 ppm IBA talc, 8000 ppm IBA talc, or inert talc. All cuttings were placed on a mist bench in a greenhouse for 9 weeks. Hardwood cuttings were supplemented with bottom heat at 24 °C. No treatments were successful in inducing adventitious root formation. I conclude that pygmy fringetree seeds possess complex dormancy that was not able to be overcome by the treatments utilized. However, this result is confounded by the age of the seeds used in the experiment. I also conclude that vegetative propagation of pygmy fringetree is highly dependent on the time of year cuttings are harvested. Further research of both seed and asexual propagation methods need to be explored before pygmy fringetree can be propagated on a commercial scale.

The Influence of Propagation Model and Sectorization over WCDMA Capacity

In this paper we use a dynamic model that we have developed for WCDMA capacity analysis using MATLAB and a GIS based planning tool, to estimate the capacity of a mobile system under different conditions like number of cells, propagation model, sectorization and handover margin.

Sistematic, population genetics, propagation and conservation of Prunus azorica (Rosaceae)

Tese de Doutoramento, Biologia (Ecologia Vegetal), 25 de Junho de 2013, Universidade dos Açores.

Sistematics, population genetics, propagation and conservation of Picconia azorica (Tutin) Knobl. (Oleaceae)

Tese de Doutoramento, Biologia (Ecologia Vegetal), 24 de Junho de 2013, Universidade dos Açores.