Characterization of thermal and mechanical properties of polypropylene-based composites for fuel cell bipolar plates and development of educational tools in hydrogen and fuel cell technologies

In this project we developed conductive thermoplastic resins by adding varying amounts of three different carbon fillers: carbon black (CB), synthetic graphite (SG) and multi-walled carbon nanotubes (CNT) to a polypropylene matrix for application as fuel cell bipolar plates. This component of fuel cells provides mechanical support to the stack, circulates the gases that participate in the electrochemical reaction within the fuel cell and allows for removal of the excess heat from the system. The materials fabricated in this work were tested to determine their mechanical and thermal properties. These materials were produced by adding varying amounts of single carbon fillers to a polypropylene matrix (2.5 to 15 wt.% Ketjenblack EC-600 JD carbon black, 10 to 80 wt.% Asbury Carbon's Thermocarb TC-300 synthetic graphite, and 2.5 to 15 wt.% of Hyperion Catalysis International's FIBRILTM multi-walled carbon nanotubes) In addition, composite materials containing combinations of these three fillers were produced. The thermal conductivity results showed an increase in both through-plane and in-plane thermal conductivities, with the largest increase observed for synthetic graphite. The Department of Energy (DOE) had previously set a thermal conductivity goal of 20 W/m·K, which was surpassed by formulations containing 75 wt.% and 80 wt.% SG, yielding in-plane thermal conductivity values of 24.4 W/m·K and 33.6 W/m·K, respectively. In addition, composites containing 2.5 wt.% CB, 65 wt.% SG, and 6 wt.% CNT in PP had an in–plane thermal conductivity of 37 W/m·K. Flexural and tensile tests were conducted. All composite formulations exceeded the flexural strength target of 25 MPa set by DOE. The tensile and flexural modulus of the composites increased with higher concentration of carbon fillers. Carbon black and synthetic graphite caused a decrease in the tensile and flexural strengths of the composites. However, carbon nanotubes increased the composite tensile and flexural strengths. Mathematical models were applied to estimate through-plane and in-plane thermal conductivities of single and multiple filler formulations, and tensile modulus of single-filler formulations. For thermal conductivity, Nielsen's model yielded accurate thermal conductivity values when compared to experimental results obtained through the Flash method. For prediction of tensile modulus Nielsen's model yielded the smallest error between the predicted and experimental values. The second part of this project consisted of the development of a curriculum in Fuel Cell and Hydrogen Technologies to address different educational barriers identified by the Department of Energy. By the creation of new courses and enterprise programs in the areas of fuel cells and the use of hydrogen as an energy carrier, we introduced engineering students to the new technologies, policies and challenges present with this alternative energy. Feedback provided by students participating in these courses and enterprise programs indicate positive acceptance of the different educational tools. Results obtained from a survey applied to students after participating in these courses showed an increase in the knowledge and awareness of energy fundamentals, which indicates the modules developed in this project are effective in introducing students to alternative energy sources.

Dynamic modeling of active regeneration in catalyzed and non-catalyzed diesel particulate filters

Particulate matter (PM) emissions standards set by the US Environmental Protection Agency (EPA) have become increasingly stringent over the years. The EPA regulation for PM in heavy duty diesel engines has been reduced to 0.01 g/bhp-hr for the year 2010. Heavy duty diesel engines make use of an aftertreatment filtration device, the Diesel Particulate Filter (DPF). DPFs are highly efficient in filtering PM (known as soot) and are an integral part of 2010 heavy duty diesel aftertreatment system. PM is accumulated in the DPF as the exhaust gas flows through it. This PM needs to be removed by oxidation periodically for the efficient functioning of the filter. This oxidation process is also known as regeneration. There are 2 types of regeneration processes, namely active regeneration (oxidation of PM by external means) and passive oxidation (oxidation of PM by internal means). Active regeneration occurs typically in high temperature regions, about 500 - 600 °C, which is much higher than normal diesel exhaust temperatures. Thus, the exhaust temperature has to be raised with the help of external devices like a Diesel Oxidation Catalyst (DOC) or a fuel burner. The O2 oxidizes PM producing CO2 as oxidation product. In passive oxidation, one way of regeneration is by the use of NO2. NO2 oxidizes the PM producing NO and CO2 as oxidation products. The passive oxidation process occurs at lower temperatures (200 - 400 °C) in comparison to the active regeneration temperatures. Generally, DPF substrate walls are washcoated with catalyst material to speed up the rate of PM oxidation. The catalyst washcoat is observed to increase the rate of PM oxidation. The goal of this research is to develop a simple mathematical model to simulate the PM depletion during the active regeneration process in a DPF (catalyzed and non-catalyzed). A simple, zero-dimensional kinetic model was developed in MATLAB. Experimental data required for calibration was obtained by active regeneration experiments performed on PM loaded mini DPFs in an automated flow reactor. The DPFs were loaded with PM from the exhaust of a commercial heavy duty diesel engine. The model was calibrated to the data obtained from active regeneration experiments. Numerical gradient based optimization techniques were used to estimate the kinetic parameters of the model.

How do we teach usability? An Investigation of Usability Instruction in Technical Communication

This dissertation investigates the curricular implementation of usability instruction in technical communication. Though there are a plethora of publications and studies on usability in technical communication, little discussion focuses on usability instruction in the classroom or its implementation in the curriculum. Thus, this exploratory qualitative research seeks to contribute to a better understanding about technical communication students' and instructors' knowledge of and experiences with usability practices in the classroom, the challenges that impacted their usability efforts, and their recommendations on how their efforts could be improved. The study results demonstrate the need for more productive discussion on this issue and for developing more effective strategies for implementing usability in the classroom.

AN ASSESSMENT OF BALLAST SOURCE'S QUALITY AND LOCATIONS WITH RESPECT TO MDOT'S UPGRADE OF THE WOLVERINE RAILROAD LINE FOR HIGH SPEED RAIL USEAGE

The Michigan Department of Transportation is evaluating upgrading their portion of the Wolverine Line between Chicago and Detroit to accommodate high speed rail. This will entail upgrading the track to allow trains to run at speeds in excess of 110 miles per hour (mph). An important component of this upgrade will be to assess the requirement for ballast material for high speed rail. In the event that the existing ballast materials do not meet specifications for higher speed train, additional ballast will be required. The purpose of this study, therefore, is to investigate the current MDOT railroad ballast quality specifications and compare them to both the national and international specifications for use on high speed rail lines. The study found that while MDOT has quality specifications for railroad ballast it does not have any for high speed rail. In addition, the American Railway Engineering and Maintenance-of-Way Association (AREMA), while also having specifications for railroad ballast, does not have specific specifications for high speed rail lines. The AREMA aggregate specifications for ballast include the following tests: (1) LA Abrasion, (2) Percent Moisture Absorption, (3) Flat and Elongated Particles, (4) Sulfate Soundness test. Internationally, some countries do require a highly standard for high speed rail such as the Los Angeles (LA) Abrasion test, which is uses a higher standard performance and the Micro Duval test, which is used to determine the maximum speed that a high speed can operate at. Since there are no existing MDOT ballast specification for high speed rail, it is assumed that aggregate ballast specifications for the Wolverine Line will use the higher international specifications. The Wolverine line, however, is located in southern Michigan is a region of sedimentary rocks which generally do not meet the existing MDOT ballast specifications. The investigation found that there were only 12 quarries in the Michigan that meet the MDOT specification. Of these 12 quarries, six were igneous or metamorphic rock quarries, while six were carbonate quarries. Of the six carbonate quarries four were locate in the Lower Peninsula and two in the Upper Peninsula. Two of the carbonate quarries were located in near proximity to the Wolverine Line, while the remaining quarries were at a significant haulage distance. In either case, the cost of haulage becomes an important consideration. In this regard, four of the quarries were located with lake terminals allowing water transportation to down state ports. The Upper Peninsula also has a significant amount of metal based mining in both igneous and metamorphic rock that generate significant amount of waste rock that could be used as a ballast material. The main drawback, however, is the distance to the Wolverine rail line. One potential source is the Cliffs Natural Resources that operates two large surface mines in the Marquette area with rail and water transportation to both Lake Superior and Lake Michigan. Both mines mine rock with a very high compressive strength far in excess of most ballast materials used in the United States and would make an excellent ballast materials. Discussions with Cliffs, however, indicated that due to environmental concerns that they would most likely not be interested in producing a ballast material. In the United States carbonate aggregates, while used for ballast, many times don't meet the ballast specifications in addition to the problem of particle degradation that can lead to fouling and cementation issues. Thus, many carbonate aggregate quarries in close proximity to railroads are not used. Since Michigan has a significant amount of carbonate quarries, the research also investigated using the dynamic properties of aggregate as a possible additional test for aggregate ballast quality. The dynamic strength of a material can be assessed using a split Hopkinson Pressure Bar (SHPB). The SHPB has been traditionally used to assess the dynamic properties of metal but over the past 20 years it is now being used to assess the dynamic properties of brittle materials such as ceramics and rock. In addition, the wear properties of metals have been related to their dynamic properties. Wear or breakdown of railroad ballast materials is one of the main problems with ballast material due to the dynamic loading generated by trains and which will be significantly higher for high speed rails. Previous research has indicated that the Port Inland quarry along Lake Michigan in the Southern Upper Peninsula has significant dynamic properties that might make it potentially useable as an aggregate for high speed rail. The dynamic strength testing conducted in this research indicate that the Port Inland limestone in fact has a dynamic strength close to igneous rocks and much higher than other carbonate rocks in the Great Lakes region. It is recommended that further research be conducted to investigate the Port Inland limestone as a high speed ballast material.

The Role of Fraternal Organisation in Migration and Informal Labour Organisations in Mining Communities: Cornwall, the Keweenaw, and California Compared

During the second half of the nineteenth century fraternal and benevolent associations of numerous descriptions grew and prospered in mining communities everywhere. They played an important, but neglected role, in assisting transatlantic migration and movement between mining districts as well as building social capital within emerging mining communities. They helped to build bridges between different ethnic communities, provided conduits between labour and management, and networked miners into the non-mining community. Their influence spread beyond the adult males that made up most of their membership to their wives and families and provided levels of social and economic support otherwise unobtainable at that time. Of course, the influence of these organisations could also be divisive where certain groups or religions were excluded and they may have worked to exacerbate, as much as ameliorate, the problems of community development. This paper will examine some of these issues by looking particularly at the role of Freemasonry and Oddfellowry in Cornwall, Calumet, and Nevada City between 1860 and 1900. Work on fraternity in the Keweenaw was undertaken in Houghton some years ago with a grant from the Copper Country Archive and has since been continued by privately funded research in California and other Western mining states. Some British aspects of this research can be found in my article on mining industrial relations in Labour History Review April 2006

An Investigation of Age-Hardening in a Commercial Copper-Beryllium Alloy

This investigation is concerned with the age-hardening process as exemplified by the aging of a commercial Cu-Be alloy and, in particular, with this pro­cess as determined by X-ray methods. The amount of infor­mation available on age-hardening of commercial alloys is scanty and what information there is, is inaccurate.

Teaching and assessment of implant dentistry in undergraduate and postgraduate education: a European consensus

This paper constitutes a summary of the consensus documents agreed at the First European Workshop on Implant Dentistry University Education held in Prague on 19-22 June 2008. Implant dentistry is becoming increasingly important treatment alternative for the restoration of missing teeth, as patients expectations and demands increase. Furthermore, implant related complications such as peri-implantitis are presenting more frequently in the dental surgery. This consensus paper recommends that implant dentistry should be an integral part of the undergraduate curriculum. Whilst few schools will achieve student competence in the surgical placement of implants this should not preclude the inclusion of the fundamental principles of implant dentistry in the undergraduate curriculum such as the evidence base for their use, indications and contraindications and treatment of the complications that may arise. The consensus paper sets out the rationale for the introduction of implant dentistry in the dental curriculum and the knowledge base for an undergraduate programme in the subject. It lists the competencies that might be sought without expectations of surgical placement of implants at this stage and the assessment methods that might be employed. The paper also addresses the competencies and educational pathways for postgraduate education in implant dentistry.

In vitro comparison of laser fluorescence performance with visual examination for detection of occlusal caries in permanent and primary molars

The aim of this study was to compare the performance of the DIAGNOdent 2095 with visual examination for occlusal caries detection in permanent and primary molars. The sample comprised 148 permanent human molars and 179 primary human molars. The samples were measured and visually examined three times by two examiners. After measurement, the teeth were histologically prepared and assessed for caries extension. Sensitivity, specificity, accuracy and area under the receiver operating characteristics (ROC) curve were calculated. Intra-class correlation (ICC), unweighted kappa and the Bland and Altman method were used to assess inter- and intra-examiner reproducibility. DIAGNOdent showed higher specificity and lower sensitivity than did visual examination. The ICC values indicated an excellent agreement between the examinations. Kappa values varied from good to excellent for DIAGNOdent but from poor to good for visual examination. In conclusion, the DIAGNOdent may be a useful adjunct to conventional methods for occlusal caries detection.

Comparison of music perception in bilateral and unilateral cochlear implant users and normal-hearing subjects

Music plays an important role in the daily life of cochlear implant (CI) users, but electrical hearing and speech processing pose challenges for enjoying music. Studies of unilateral CI (UCI) users' music perception have found that these subjects have little difficulty recognizing tempo and rhythm but great difficulty with pitch, interval and melody. The present study is an initial step towards understanding music perception in bilateral CI (BCI) users. The Munich Music Questionnaire was used to investigate music listening habits and enjoyment in 23 BCI users compared to 2 control groups: 23 UCI users and 23 normal-hearing (NH) listeners. Bilateral users appeared to have a number of advantages over unilateral users, though their enjoyment of music did not reach the level of NH listeners.

Thromboelastometry for the assessment of coagulation abnormalities in early and established adult sepsis: a prospective cohort study

INTRODUCTION: The inflammatory response to an invading pathogen in sepsis leads to complex alterations in hemostasis by dysregulation of procoagulant and anticoagulant factors. Recent treatment options to correct these abnormalities in patients with sepsis and organ dysfunction have yielded conflicting results. Using thromboelastometry (ROTEM(R)), we assessed the course of hemostatic alterations in patients with sepsis and related these alterations to the severity of organ dysfunction. METHODS: This prospective cohort study included 30 consecutive critically ill patients with sepsis admitted to a 30-bed multidisciplinary intensive care unit (ICU). Hemostasis was analyzed with routine clotting tests as well as thromboelastometry every 12 hours for the first 48 hours, and at discharge from the ICU. Organ dysfunction was quantified using the Sequential Organ Failure Assessment (SOFA) score. RESULTS: Simplified Acute Physiology Score II and SOFA scores at ICU admission were 52 +/- 15 and 9 +/- 4, respectively. During the ICU stay the clotting time decreased from 65 +/- 8 seconds to 57 +/- 5 seconds (P = 0.021) and clot formation time (CFT) from 97 +/- 63 seconds to 63 +/- 31 seconds (P = 0.017), whereas maximal clot firmness (MCF) increased from 62 +/- 11 mm to 67 +/- 9 mm (P = 0.035). Classification by SOFA score revealed that CFT was slower (P = 0.017) and MCF weaker (P = 0.005) in patients with more severe organ failure (SOFA >or= 10, CFT 125 +/- 76 seconds, and MCF 57 +/- 11 mm) as compared with patients who had lower SOFA scores (SOFA <10, CFT 69 +/- 27, and MCF 68 +/- 8). Along with increasing coagulation factor activity, the initially increased International Normalized Ratio (INR) and prolonged activated partial thromboplastin time (aPTT) corrected over time. CONCLUSIONS: Key variables of ROTEM(R) remained within the reference ranges during the phase of critical illness in this cohort of patients with severe sepsis and septic shock without bleeding complications. Improved organ dysfunction upon discharge from the ICU was associated with shortened coagulation time, accelerated clot formation, and increased firmness of the formed blood clot when compared with values on admission. With increased severity of illness, changes of ROTEM(R) variables were more pronounced.

The Active Subjects of Welfare Reform: a Street-Level Comparison of Employment Services in Australia and Denmark

This paper explores the similarities and differences between Denmark and Australia in adopting welfare reform activation measures in the field of employment services. In Australia and Denmark the discourse of welfare reform centres the 'activation' of citizens through 'mutual obligation' type requirements. Through various forms of case management, unemployed individuals are encouraged to act upon themselves in creating the right set of ethical dispositions congruent with 'active citizenship'. At the same time any resistance to heightened conditionality on the part of the unemployed person is dealt with through a range of coercive and disciplinary techniques. A comparative case study between these two countries allows us to consider how similar ideas, discourse and principles are shaping policy implementation in countries that have very different welfare state trajectories and institutional arrangements for the delivery of social welfare generally and employment services specifically. And in research terms, a comparison between a Nordic welfare state and an Anglo-Saxon welfare state provides an opportunity to critically examine the utility of 'welfare regime' type analyses and the neo-liberal convergence thesis in comparative welfare research. On the basis of empirical analysis, the article concludes that a single focus on abstract typologies or political ideologies is not very helpful in getting the measure of welfare reform (or any other major policy development for that matter). At the 'street-level' of policy practice there is considerably more ambiguity, incoherence and contradiction than is suggested by linear accounts of welfare reform.

Epidemiology and direct medical costs of osteoporotic fractures in men and women in Switzerland

The aim of this study was to estimate the hospitalization incidence and the total number of hospital days related to all fractures and osteoporotic fractures in the year 2000 in Switzerland and to compare these with data from other frequent disorders in men and women. The official administrative and medical statistics database of the Swiss Federal Office of Statistics (SFOS) from the year 2000 was used. It covered 81.2% of all registered patient admissions and was considered to be representative of the entire population. We included the ICD-10 codes of 84 diagnoses that were compatible with an underlying osteoporosis and applied the best matching age-specific osteoporosis attribution rates published for the ICD-9 diagnosis codes to the individual ICD-10 codes. To preserve comparability with previously published data from 1992, we grouped the data related to the ICD-10 fracture codes into seven diagnosis pools (fractures of the axial skeleton, fractures of the proximal upper limbs, fractures of the distal upper limbs, fractures of the proximal lower limbs, fractures of the distal lower limbs, multiple fractures, and osteoporosis) and analyzed them separately for women and men by age group. Incidences of hospitalization due to fractures were calculated, and the direct medical costs related to hospitalization were estimated. In addition, we compared the results with those from chronic pulmonary obstructive disease (COPD), stroke, acute myocardial infarction, heart failure, diabetes and breast carcinoma from the same database. In Switzerland during 2000, 62,535 hospitalizations for fractures (35,586 women and 26,949 men) were registered. Fifty-one percent of all fractures in women and 24% in men were considered as osteoporotic. The overall incidences of hospitalization due to fractures were 969 and 768 per 100,000 in women and men, respectively. The hospitalization incidences for fractures of the proximal lower limbs and the axial skeleton increased exponentially after the age of 65 years. The direct medical cost of hospitalization of patients with osteoporosis and/or related fractures was 357 million CHF. Hip fractures accounted for approximately half of these costs in women and men. Among other common diseases in women and men, osteoporosis ranked number 1 in women and number 2 (behind COPD) in men. When compared with data from 1992, the average length of stay had shortened by 8.4 days for women and 4.7 days for men, leading to a decrease of almost 40% in direct medical costs related to acute hospitalizations. This apparent decrease in cost might result from a shift into the ambulatory cost segment, for which the assessment and management tools need to be developed. We conclude that, in 2000, osteoporosis continued to be a heavy burden on the Swiss healthcare system. Lack of awareness of the disease and its consequences prevents widespread use of drugs with anti-fracture efficacy. This limits their potential to reduce costs.

Risk scoring for setting priorities in a monitoring of antimicrobial resistance in meat and meat products

Meat and meat products can be contaminated with different species of bacteria resistant to various antimicrobials. The human health risk of a type of meat or meat product carry by emerging antimicrobial resistance depends on (i) the prevalence of contamination with resistant bacteria, (ii) the human health consequences of an infection with a specific bacterium resistant to a specific antimicrobial and (iii) the consumption volume of a specific product. The objective of this study was to compare the risk for consumers arising from their exposure to antibiotic resistant bacteria from meat of four different types (chicken, pork, beef and veal), distributed in four different product categories (fresh meat, frozen meat, dried raw meat products and heat-treated meat products). A semi-quantitative risk assessment model, evaluating each food chain step, was built in order to get an estimated score for the prevalence of Campylobacter spp., Enterococcus spp. and Escherichia coli in each product category. To assess human health impact, nine combinations of bacterial species and antimicrobial agents were considered based on a published risk profile. The combination of the prevalence at retail, the human health impact and the amount of meat or product consumed, provided the relative proportion of total risk attributed to each category of product, resulting in a high, medium or low human health risk. According to the results of the model, chicken (mostly fresh and frozen meat) contributed 6.7% of the overall risk in the highest category and pork (mostly fresh meat and dried raw meat products) contributed 4.0%. The contribution of beef and veal was of 0.4% and 0.1% respectively. The results were tested and discussed for single parameter changes of the model. This risk assessment was a useful tool for targeting antimicrobial resistance monitoring to those meat product categories where the expected risk for public health was greater.

Antibodies to Aqx toxin of Actinobacillus equuli in horses and foals

Actinobacillus equuli is found in the normal oral flora of horses, but has been associated with several diseases, and particularly with the usually fatal septicaemia in neonatal foals which is thought to be associated with a failure of the passive transfer of immunoglobulins via the colostrum. The Aqx protein of A equuli, belonging to the RTX family of pore-forming toxins, is also cytotoxic to horse lymphocytes. The presence of antibodies to Aqx was investigated in sera from individual horses from different regions; the sera from adult horses and foals 24 hours after birth reacted with Aqx, and sera from foals sampled shortly after an intake of colostrum also reacted with Aqx, but sera from foals taken before an intake of colostrum did not react with Aqx.

An Evaluation of Effective Fiber in Beef Feedlot Finishing Diets

A study was designed to collect a database of Iowa feedlot rations for determination of effective neutral detergent fiber (NDF) in complete diets from fiber analysis and particle size determination of individual feed ingredients and compare this with particle size determination of mixed wet rations. Seventy-one beef finishing total mixed rations were collected by ISU Extension Beef Field Specialists across Iowa. Producers were asked to complete a form assessing the acidosis risk associated with each ration. The average NDF of these diets was 25.9%. Of the total mixed rations 1.33 % remained in the top tray (>.75 in.), 47.27 % remained in the middle tray (>.31 in.), and 50.88 % was smaller than the .31 in screen. The effective NDF (eNDF) calculated from the eNDF of the ingredients averaged 10.56%. Estimated eNDF from total diet NDF and the percentage of the total diet in the top and middle trays averaged 12.47%. The calculated eNDF from non-grain sources alone averaged 3.6%. The percentage of digestive deads was weakly related to the percentage of the ration in the bottom tray (r=.19), the percentage in the top tray (r=- .46) and the effective NDF of the ration (r=-.23). The percentage of bloat was related to the total NDF of the diet (r=.28) and the effective fiber from non-grain sources (r=-.23). The number of off-feed incidences was related to the dry matter of the ration (r=.38), the apparent eNDF (r=-.28) and the percentage of ration in the bottom tray (r=.24). This study confirms that there is some relationship between effective NDF of the diet, effective NDF from non-grain sources or diet particle size; and acidosis indicators. These relationships are weak, however, indicating that other factors such as feedbunk management, feed processing, feed presentation and feed mixing likely also play a role in the incidence of acidosis in feedlot cattle.