Flash pyrolysis of biomass for liquid fuels

DUE TO COPYRIGHT RESTRICTIONS ONLY AVAILABLE FOR CONSULTATION AT ASTON UNIVERSITY LIBRARY AND INFORMATION SERVICES WITH PRIOR ARRANGEMENT

Intermediate pyrolysis of biomass energy pellets for producing sustainable liquid, gaseous and solid fuels

This work describes the use of intermediate pyrolysis system to produce liquid, gaseous and solid fuels from pelletised wood and barley straw feedstock. Experiments were conducted in a pilot-scale system and all products were collected and analysed. The liquid products were separated into an aqueous phase and an organic phase (pyrolysis oil) under gravity. The oil yields were 34.1 wt.% and 12.0 wt.% for wood and barley straw, respectively. Analysis found that both oils were rich in heterocyclic and phenolic compounds and have heating values over 24 MJ/kg. The yields of char for both feedstocks were found to be about 30 wt.%, with heating values similar to that of typical sub-bituminous class coal. Gas yields were calculated to be approximately 20 wt.%. Studies showed that both gases had heating values similar to that of downdraft gasification producer gas. Analysis on product energy yields indicated the process efficiency was about 75%. © 2014 Elsevier Ltd. All rights reserved.

The intermediate pyrolysis of de-inking sludge to produce a sustainable liquid fuel

De-inking sludge is a waste product generated from secondary fibre paper mills who manufacture recycled paper into new paper sheets; it refers directly to the solid residues which evolve during the de-inking stage of the paper pulping process. The current practice for the disposal of this waste is either by land-spreading, land-filling or incineration which are unsustainable. This work has explored the intermediate pyrolysis of pre-conditioned de-inking sludge pellets in a recently patented 20 kg/h intermediate pyrolysis reactor (The Pyroformer). The reactor is essentially two co-axial screws which are configured in such a way as to circulate solids within the reactor and thus facilitate in the cracking of tars. The potential application of using the volatile organic vapours and permanent gases evolved would be to generate both combined heat and power (CHP) located at paper making sites. The results show that de-inking sludge could be successfully pyrolysed and the organic vapours produced were composed of a mixture of aromatic hydrocarbons, phenolic compounds and some fatty acid methyl esters as detected by liquid GC-MS. The calorific value of the oil after condensing was between 36 and 37 MJ/kg and the liquid fuel properties were also determined, permanent gases were detected by a GC-TCD and were composed of approximately 24% CO, 6% CH and 70% CO (v/v%). The solid residue from pyrolysis also contained a small residual calorific value, and was largely composed of mainly calcium based inert metal oxides. The application of applying intermediate pyrolysis to de-inking sludge for both CHP production and waste reduction is in principle a feasible technology which could be applied at secondary fibre paper mills. © 2013 Elsevier B.V. All rights reserved.

Pyrolysis of polyamide 6 under catalytic conditions and its application to reutilization of carpets

ε-caprolactam is a monomer of high value. Therefore, the chemical reutilization of polyamide 6 containing carpets for ε-caprolactam recovery offers some economic benefit and is performed on a technical scale with the help of the Zimmer-process. By this process polyamide 6 is depolymerized with steam and phosphoric acid. An alternative to this process is the thermal depolymerization - catalyzed or non-catalyzed. To investigate this alternative in more detail, the formal kinetic parameters of (i) the thermal depolymerization of polyamide 6, (ii) the thermal depolymerization in presence of sodium/potassium hydoxide, and (iii) the thermal depolymerization in presence of phosphoric acid are determined in this work. Based on the kinetics of the catalyzed or non-catalyzed depolymerization a stepwise pyrolysis procedure is designed by which the formation of ε-caprolactam from polyamide 6 can be separated from the formation of other pyrolysis products. © 2001 Elsevier Science B.V.

Matricial Model for the Study of Lower Bounds

Let V be an array. The range query problem concerns the design of data structures for implementing the following operations. The operation update(j,x) has the effect vj ← vj + x, and the query operation retrieve(i,j) returns the partial sum vi + ... + vj. These tasks are to be performed on-line. We define an algebraic model – based on the use of matrices – for the study of the problem. In this paper we establish as well a lower bound for the sum of the average complexity of both kinds of operations, and demonstrate that this lower bound is near optimal – in terms of asymptotic complexity.

A lumped parameter model for the analysis of the motion of the muscles of the lower limbs under whole-body vibration

Through a lumped parameter modelling approach, a dynamical model, which can reproduce the motion of the muscles of a human body standing in different postures during Whole Body Vibrations (WBVs) treatment, has been developed. The key parameters, associated to the dynamics of the motion of the muscles of the lower limbs, have been identified starting from accelerometer measurements. The developed model can be usefully applied to the optimization of WBVs treatments which can effectively enhance muscle activation. © 2013 IEEE.

Experimental comparison of dynamic tracking performance of iGPS and laser tracker

External metrology systems are increasingly being integrated with traditional industrial articulated robots, especially in the aerospace industries, to improve their absolute accuracy for precision operations such as drilling, machining and jigless assembly. While currently most of the metrology assisted robotics control systems are limited in their position update rate, such that the robot has to be stopped in order to receive a metrology coordinate update, some recent efforts are addressed toward controlling robots using real-time metrology data. The indoor GPS is one of the metrology systems that may be used to provide real-time 6DOF data to a robot controller. Even if there is a noteworthy literature dealing with the evaluation of iGPS performance, there is, however, a lack of literature on how well the iGPS performs under dynamic conditions. This paper presents an experimental evaluation of the dynamic measurement performance of the iGPS, tracking the trajectories of an industrial robot. The same experiment is also repeated using a laser tracker. Besides the experiment results presented, this paper also proposes a novel method for dynamic repeatability comparisons of tracking instruments. © 2011 Springer-Verlag London Limited.

Intermediate pyrolysis of biomass

A comparison of fast and intermediate processes is given. New developments in technology are described for intermediate pyrolysis and an advanced integrative combination of biomass based processes is proposed. © 2013 Woodhead Publishing Limited All rights reserved.

Fast pyrolysis of biomass for the production of liquids

This chapter examines the fast pyrolysis of biomass to produce liquids for use as fuels and chemicals. The technology for fast pyrolysis is described and the characteristics of the main product bio-oil. This primary liquid is characterised by the many properties that affect its use. These properties have caused increasingly extensive research to be undertaken to address properties that need modification and this area is reviewed in terms of physical, catalytic and chemical upgrading. Of particular note is the increasing diversity of upgrading methods. © 2013 Woodhead Publishing Limited All rights reserved.

Comprehensive secondary pyrolysis in fluidized-bed fast pyrolysis of biomass, a fluid dynamics based modelling effort

Homogenous secondary pyrolysis is category of reactions following the primary pyrolysis and presumed important for fast pyrolysis. For the comprehensive chemistry and fluid dynamics, a probability density functional (PDF) approach is used; with a kinetic scheme comprising 134 species and 4169 reactions being implemented. With aid of acceleration techniques, most importantly Dimension Reduction, Chemistry Agglomeration and In-situ Tabulation (ISAT), a solution within reasonable time was obtained. More work is required; however, a solution for levoglucosan (C6H10O5) being fed through the inlet with fluidizing gas at 500 °C, has been obtained. 88.6% of the levoglucosan remained non-decomposed, and 19 different decomposition product species were found above 0.01% by weight. A homogenous secondary pyrolysis scheme proposed can thus be implemented in a CFD environment and acceleration techniques can speed-up the calculation for application in engineering settings.

Predicting practical benefits of dynamic asset ratings of 33kv distribution transformers

This paper reports potential benefits around dynamic thermal rating prediction of primary transformers within Western Power Distribution (WPD) managed Project FALCON (Flexible Approaches to Low Carbon Optimised Networks). Details of the thermal modelling, parameter optimisation and results validation are presented with asset and environmental data (measured and day/week-ahead forecast) which are used for determining dynamic ampacity. Detailed analysis of ratings and benefits and confidence in ability to accurately predict dynamic ratings are presented. Investigating the effect of sustained ONAN rating compared to a dynamic rating shows that there is scope to increase sustained ratings under ONAN operating conditions by up to 10% higher between December and March with a high degree of confidence. However, under high ambient temperature conditions this dynamic rating may also reduce in the summer months.

Weather forecasting to predict practical dynamic asset rating of overhead lines

This paper describes the potential of pre-setting 11kV overhead line ratings over a time period of sufficient length to be useful to the real-time management of overhead lines. This forecast is based on short and long term freely available weather forecasts and is used to help investigate the potential for realising dynamic rating benefits on the electricity network. A comparison between the realisable benefits in ratings using this forecast data, over the period of a year has been undertaken.

Expanding the biomass resource:sustainable oil production via fast pyrolysis of low input high diversity biomass and the potential integration of thermochemical and biological conversion routes

Waste biomass is generated during the conservation management of semi-natural habitats, and represents an unused resource and potential bioenergy feedstock that does not compete with food production. Thermogravimetric analysis was used to characterise a representative range of biomass generated during conservation management in Wales. Of the biomass types assessed, those dominated by rush (Juncus effuses) and bracken (Pteridium aquilinum) exhibited the highest and lowest volatile compositions respectively and were selected for bench scale conversion via fast pyrolysis. Each biomass type was ensiled and a sub-sample of silage was washed and pressed. Demineralization of conservation biomass through washing and pressing was associated with higher oil yields following fast pyrolysis. The oil yields were within the published range established for the dedicated energy crops miscanthus and willow. In order to examine the potential a multiple output energy system was developed with gross power production estimates following valorisation of the press fluid, char and oil. If used in multi fuel industrial burners the char and oil alone would displace 3.9 × 105 tonnes per year of No. 2 light oil using Welsh biomass from conservation management. Bioenergy and product development using these feedstocks could simultaneously support biodiversity management and displace fossil fuels, thereby reducing GHG emissions. Gross power generation predictions show good potential.

Development of a technological innovation capability assessment model:a case study of manufacturing SMEs in Sialkot, Pakistan

Small and Medium Enterprises (SMEs) play an important part in the economy of any country. Initially, a flat management hierarchy, quick response to market changes and cost competitiveness were seen as the competitive characteristics of an SME. Recently, in developed economies, technological capabilities (TCs) management- managing existing and developing or assimilating new technological capabilities for continuous process and product innovations, has become important for both large organisations and SMEs to achieve sustained competitiveness. Therefore, various technological innovation capability (TIC) models have been developed at firm level to assess firms‘ innovation capability level. These models output help policy makers and firm managers to devise policies for deepening a firm‘s technical knowledge generation, acquisition and exploitation capabilities for sustained technological competitive edge. However, in developing countries TCs management is more of TCs upgrading: acquisitions of TCs from abroad, and then assimilating, innovating and exploiting them. Most of the TIC models for developing countries delineate the level of TIC required as firms move from the acquisition to innovative level. However, these models do not provide tools for assessing the existing level of TIC of a firm and various factors affecting TIC, to help practical interventions for TCs upgrading of firms for improved or new processes and products. Recently, the Government of Pakistan (GOP) has realised the importance of TCs upgrading in SMEs-especially export-oriented, for their sustained competitiveness. The GOP has launched various initiatives with local and foreign assistance to identify ways and means of upgrading local SMEs capabilities. This research targets this gap and developed a TICs assessment model for identifying the existing level of TIC of manufacturing SMEs existing in clusters in Sialkot, Pakistan. SME executives in three different export-oriented clusters at Sialkot were interviewed to analyse technological capabilities development initiatives (CDIs) taken by them to develop and upgrade their firms‘ TCs. Data analysed at CDI, firm, cluster and cross-cluster level first helped classify interviewed firms as leader, follower and reactor, with leader firms claiming to introduce mostly new CDIs to their cluster. Second, the data analysis displayed that mostly interviewed leader firms exhibited ‗learning by interacting‘ and ‗learning by training‘ capabilities for expertise acquisition from customers and international consultants. However, these leader firms did not show much evidence of learning by using, reverse engineering and R&D capabilities, which according to the extant literature are necessary for upgrading existing TIC level and thus TCs of firm for better value-added processes and products. The research results are supported by extant literature on Sialkot clusters. Thus, in sum, a TIC assessment model was developed in this research which qualitatively identified interviewed firms‘ TIC levels, the factors affecting them, and is validated by existing literature on interviewed Sialkot clusters. Further, the research gives policy level recommendations for TIC and thus TCs upgrading at firm and cluster level for targeting better value-added markets.