Air flow humidification for air-assisted boom sprayer

The air-assisted ground spray is fairly widespread. However, due to the unpredictable weather conditions, the operational efficiency is impaired by stops on grounds of low humidity and high temperatures. The aim of this work was to assess an air humidification method and evaluate its impact on temperature and air humidity for the air curtain of the air-assisted sprayer. With respect to relative air humidity, it has increased in 6.59%, being the maximum change when inserting 1.92 L min-1. So, it is concluded that the pipeline humidification might significantly reduce temperature and enhance air humidity. The treatments performed in this study consisted of a varied flow of a humidity device, related to weather conditions. Temperature and relative air humidity were measured at 1.0 m height from right to left of middle point of the machine, corresponding to the end of the spray boom, in the middle and end of right spray boom. The readings were also performed at three different distances from the end of the pipeline and at 0.25 and 0.50 m from that to the soil. The results show that 0.48 L min-1 in the humidification system has promoted a better efficiency in reducing air-temperature, on average 2.52 ºC when compared to the non-humidified one.

Coeficiente de descarga em emissores de pivô central

Este trabalho foi desenvolvido com o objetivo de determinar, em condições laboratoriais, o coeficiente de descarga (Cd) dos emissores fixos tipo “spray” (Senninger, Nelson e Fabrimar) utilizados em equipamentos pivô central no Brasil. Foram avaliados 45 bocais Senninger, 42 bocais Nelson e 36 bocais Fabrimar, com três repetições, totalizando 369 bocais ensaiados. As pressões de funcionamento variaram entre 6 e 30 PSI (41,37 a 206,84 kPa), com intervalo de leitura a cada 2 PSI (13,79 kPa), totalizando 13 pressões analisadas por bocal. Foram ajustadas as curvas do coeficiente de descarga em função do diâmetro de bocal, para quatro pressões de operação: 10; 15; 20 e 30 PSI (68,95; 103,42; 137,90 e 206,84 kPa). Utilizou-se de dois manômetros de precisão (analógico e digital) previamente calibrados em um manômetro de peso morto. As vazões foram obtidas utilizando três medidores eletromagnético-indutivos, calibrados em recipiente volumétrico. O diâmetro dos bocais foi mensurado através de uma ampliação em projetor de perfil da marca Starrett, modelo HB 400. Os resultados evidenciaram que o coeficiente de descarga varia em função da pressão e do diâmetro do bocal. Nos ensaios conduzidos, obtiveram-se Cds compreendidos na faixa de 0,88 a 0,98 para a faixa de emissores analisados.

Physical characteristics of oily spraying liquids and droplets formed on coffee leaves and glass surfaces

The physical characteristics of a spray liquid are important in getting a good droplet formation and control efficiency over a particular target. As a function of these characteristics, it is possible to decipher which is the best adjuvant based on the respective concentration used during the spray. Therefore, ten spraying liquids were prepared, which varied in concentrations of pesticide lufenuron + profenofos, mineral oil, water and manganese sulfate. Pendant droplets formed from these mixtures were measured to examine their impact on surface tension. Droplets were applied to the surface of coffee leaves and the surface tension, contact angle formed and the leaf area wetted by the droplet, were measured. A smooth glass surface was taken as a comparative to the coffee leaves. The highest concentrations of oil resulted in lower surface tension, smaller contact angles of droplets on leaf surfaces and larger areas wetted by the droplets. Both surfaces showed hydrophilic behavior.

Distribution pattern, surface tension and contact angle of herbicides associated to adjuvants on spraying and control of Ipomoea hederifolia under rainfall incidence

ABSTRACTScarlet Morning Glory is considered to be an infesting weed that affects several crops and causes serious damage. The application of chemical herbicides, which is the primary control method, requires a broad knowledge of the various characteristics of the solution and application technology for a more efficient phytosanitary treatment. Therefore this study aimed to characterize the effect of rainfall incidence on the control of Ipomoea hederifolia, considering droplet size, surface tension, contact angle of droplets formed by herbicides liquid on vegetal and artificial surfaces, associated to adjuvants and the volumetric distribution profile of the spray jet. The addition of the adjuvants to the herbicide spraying liquid improved the application quality, as it influenced the angle formed by the spray by broadening the deposition band of the spray nozzle and thus the possible distance between the nozzles on spray boom and due the changes at droplet size, which contribute to a safety application. The rainfall occurrence affected negatively the weed control with the different spraying liquids and also the dry matter weight, suggesting that the phytosanitary product applied was washed off.

Spraying systems and traveling speed in the deposit and spectrum of droplets in cotton plant

ABSTRACT Tractor traveling speed can influence the quality of spraying depending on the application technology used. This study aimed to evaluate the droplet spectrum, the deposition and uniformity of spray distribution with different spraying systems and traveling speeds of a self-propelled sprayer in two phenological stages of the cotton plant (B9 and F13). The experimental design was randomized blocks and treatments were three spraying techniques: common flat spray tips; tilted flat jet with air induction, at 120 L ha-1; and rotary atomizer disk, 20 L ha-1, combined with four traveling speeds: 12, 15, 18 and 25 km h-1, with four replications. Spraying deposition was evaluated for both leaf surfaces from the cotton plant apex and base (stage B9) and middle part of the plant (stage F13) with a cupric marker. A laser particle analyzer also assessed the droplet spectrum. The centrifugal power spray system produces more homogeneous droplet spectrum and increased penetration of droplets into the canopy in both phenological stages. Variation on the operating conditions necessary for increased traveling speed negatively influences the pattern of spraying deposits.

Thermal Stress in a Roll-to-Roll Printed Electronics Substrate

The Roll-to-Roll process makes it possible to print electronic products continuously onto a uniform substrate. Printing components on flexible surfaces can bring down the costs of simple electronic devices such as RFID tags, antennas and transistors. The possibility of quickly printing flexible electronic components opens up a wide array of novel products previously too expensive to produce on a large scale. Several different printing methods can be used in Roll-to-Roll printing, such as gravure, spray, offset, flexographic and others. Most of the methods can also be mixed in one production line. Most of them still require years of research to reach a significant commercial level. The research for this thesis was carried out at the Konkuk University Flexible Display Research Center (KU-FDRC) in Seoul, Korea. A system using Roll-to-Roll printing requires that the motion of the web can be controlled in every direction in order to align different layers of ink properly. Between printers the ink is dried with hot air. The effects of thermal expansion on the tension of the web are studied in this work, and a mathematical model was constructed on Matlab and Simulink. Simulations and experiments lead to the conclusion that the thermal expansion of the web has a great influence on the tension of the web. Also, experimental evidence was gained that the particular printing machine used for these experiments at KU-FDRC may have a problem in controlling the speeds of the cylinders which pull the web.

Structural and operational optimisation : applications in energy systems

In this work mathematical programming models for structural and operational optimisation of energy systems are developed and applied to a selection of energy technology problems. The studied cases are taken from industrial processes and from large regional energy distribution systems. The models are based on Mixed Integer Linear Programming (MILP), Mixed Integer Non-Linear Programming (MINLP) and on a hybrid approach of a combination of Non-Linear Programming (NLP) and Genetic Algorithms (GA). The optimisation of the structure and operation of energy systems in urban regions is treated in the work. Firstly, distributed energy systems (DES) with different energy conversion units and annual variations of consumer heating and electricity demands are considered. Secondly, district cooling systems (DCS) with cooling demands for a large number of consumers are studied, with respect to a long term planning perspective regarding to given predictions of the consumer cooling demand development in a region. The work comprises also the development of applications for heat recovery systems (HRS), where paper machine dryer section HRS is taken as an illustrative example. The heat sources in these systems are moist air streams. Models are developed for different types of equipment price functions. The approach is based on partitioning of the overall temperature range of the system into a number of temperature intervals in order to take into account the strong nonlinearities due to condensation in the heat recovery exchangers. The influence of parameter variations on the solutions of heat recovery systems is analysed firstly by varying cost factors and secondly by varying process parameters. Point-optimal solutions by a fixed parameter approach are compared to robust solutions with given parameter variation ranges. In the work enhanced utilisation of excess heat in heat recovery systems with impingement drying, electricity generation with low grade excess heat and the use of absorption heat transformers to elevate a stream temperature above the excess heat temperature are also studied.

Mädätysjäännöksen rakeistus, terminen kuivaus ja energiahyötykäyttö

Tutkimuksen tavoitteena oli kartoittaa alueellisen jäteyhtiön Kymenlaakson Jäte Oy:n mahdollisuuksia rakeistaa ja termisesti kuivata mekaanisesti kuivattua mädätysjäännöstä sekä mahdollisuuksia toimittaa termisesti kuivattua materiaalia energiahyötykäyttöön. Tutkimuksessa selvitettiin myös kokemuksia lattialämmityksen käyttämisestä mädätysjäännöksen kuivaukseen. Tutkimuksessa perehdyttiin erilaisiin rakeistus- ja kuivausmenetelmiin sekä termisen kuivurin valintaan vaikuttaviin asioihin. Kuvaukset perustuvat kirjallisuudesta ja internetistä saatuihin tietoihin. Tekniikkakuvausten pohjalta lähdettiin kyselemään tarjouksia termisiä kuivauslaitteistoja myyviltä yrityksiltä. Tarjoukset pyydettiin kuiva-ainepitoisuuden muutokselle 30 %:sta 90 %:iin ja oletettiin, että kuivaukseen on käytettävissä lämpöä viideltä kaatopaikkakaasua käyttävältä mikroturbiinilta. Tutkimuksen aikana saatiin tarjous kuudelta yritykseltä. Saadut tarjoukset esiteltiin tiivistetysti raportissa ja kokonaisuudessaan ne sisällytettiin Kymenlaakson Jäte Oy:n laajempaan raporttiin, joka ei ole julkinen. Yritykset antoivat hyvin erilaisia tietoja siitä, mitä tarjoukseen sisältyy, joten tarjoukset eivät olleet suoraan vertailukelpoisia. Tarjouksista myös havaittiin, että jos Mäkikylän biokaasulaitokselta vastaanotettaisiin enimmäismäärä (19 500 t/a) mädätysjäännöstä, mikroturbiineilta saatava lämpömäärä ei riittäisi kuivaamaan kaikkea mädätysjäännöstä 90 % kuiva-ainepitoisuuteen. Tutkimuksen aikana huomattiin myös, että sitovan tarjouksen saamiseksi mädätysjäännös tulee toimittaa testattavaksi, jolloin saadaan vahvistus kuivausmenetelmän soveltuvuudesta kyseiselle materiaalille. Tutkimuksessa selvitettiin myös, minkälaisia kokemuksia löytyy lattialämmityksen käyttämisestä kuivaukseen niin Suomesta kuin maailmalta ja voiko menetelmää käyttää mädätysjäännöksen kuivaukseen. Kyseistä menetelmää on käytetty tehostamaan aurinkokuivausta, joten tutkimuksen aikana perehdyttiin erityisesti aurinkokuivaukseen liittyviin tieteellisiin artikkeleihin. Lattialämmityksen käytöstä löytyi niin heikkouksia kuin vahvuuksia. Suomessa aurinkokuivauksen ja lattialämmityksen yhdistelmä ei ole kuitenkaan päätynyt laajaan käyttöön ja syynä voidaan nähdä muun muassa kylmät ja pimeät vuodenajat sekä suuri pinta-alan tarve. Tutkimusraportissa selvitettiin lisäksi polttolaitosten edustajien kiinnostusta ja rajoituksia ottaa vastaan termisesti kuivattua mädätysjäännöstä. Tutkimuksen aikana otettiin yhteyttä alle 100 km etäisyydellä Kymenlaakson Jäte Oy:stä sijaitsevien jätteenpolttoluvan omaavien yritysten edustajiin. Saatuja vastauksia käsiteltiin tiivistetysti raportissa ja vastaukset sisällytettiin kokonaisuudessaan Kymenlaakson Jäte Oy:n laajempaan raporttiin, joka ei ole julkinen. Puhelinhaastattelujen pohjalta nähtiin, että yrityksillä on kiinnostusta materiaalia kohtaan, mutta samalla vastauksiin vaikuttavat mädätysjäännöksen analyysitulokset. Poltto-ominaisuuksiin liittyvät analyysit tullaan toteuttamaan vuoden 2012 aikana. Laitoksilla oli myös vaihtelevia rajoituksia materiaalia kohtaan, mutta analyysituloksista riippuen materiaalia voidaan hyödyntää energiana tuhansia tai jopa kymmeniä tuhansia tonneja vuodessa alle 100 km etäisyydellä Kymenlaakson Jäte Oy:stä.

Avaliação da eficiência da desinfecção de teteiras e dos tetos no processo de ordenha mecânica de vacas

O presente trabalho teve como objetivos avaliar a eficiência do processo de desinfecção de teteiras por imersão em solução desinfetante utilizando duas fontes de cloro, hipoclorito de sódio e cloro orgânico, a dinâmica de cloro residual nesses dois tipos de soluções, ao longo do processo de ordenha, e a eficiência de três métodos de desinfecção: imersão, spray e esponja na remoção de microrganismos dos tetos de vacas em lactação, utilizando o cloro como desinfetante. Foram determinados os números de coliformes totais, coliformes fecais, Staphylococcus sp e microrganismos mesófilos nas amostras colhidas das teteiras, dos tetos e da solução desinfetante. Os resultados obtidos demonstraram que a prática da desinfecção de teteiras entre vacas, utilizando-se hipoclorito de sódio ou dicloroisocianurato de sódio como fontes de cloro, na concentração em torno de 150ppm não foi eficiente na redução dos microrganismos presentes nas teteiras. A solução desinfetante a base de dicloroisocianurato de sódio apresentou maior estabilidade. Os métodos de desinfecção dos tetos proporcionaram redução nos números de microrganismos pesquisados, em todos os tratamentos utilizados, mostrando ser uma ferramenta simples para minimizar o risco de transmissão de patógenos durante a ordenha e aumentar a qualidade microbiológica do leite produzido.

Liquid transportation and distribution during (re)wetting : impact on coated papers in printing

In many industrial applications, such as the printing and coatings industry, wetting of porous materials by liquids includes not only imbibition and permeation into the bulk but also surface spreading and evaporation. By understanding these phenomena, valuable information can be obtained for improved process control, runnability and printability, in which liquid penetration and subsequent drying play important quality and economic roles. Knowledge of the position of the wetting front and the distribution/degree of pore filling within the structure is crucial in describing the transport phenomena involved. Although exemplifying paper as a porous medium in this work, the generalisation to dynamic liquid transfer onto a surface, including permeation and imbibition into porous media, is of importance to many industrial and naturally occurring environmental processes. This thesis explains the phenomena in the field of heatset web offset printing but the content and the analyses are applicable in many other printing methods and also other technologies where water/moisture monitoring is crucial in order to have a stable process and achieve high quality end products. The use of near-infrared technology to study the water and moisture response of porous pigmented structures is presented. The use of sensitive surface chemical and structural analysis, as well as the internal structure investigation of a porous structure, to inspect liquid wetting and distribution, complements the information obtained by spectroscopic techniques. Strong emphasis has been put on the scale of measurement, to filter irrelevant information and to understand the relationship between interactions involved. The near-infrared spectroscopic technique, presented here, samples directly the changes in signal absorbance and its variation in the process at multiple locations in a print production line. The in-line non-contact measurements are facilitated by using several diffuse reflectance probes, giving the absolute water/moisture content from a defined position in the dynamic process in real-time. The nearinfrared measurement data illustrate the changes in moisture content as the paper is passing through the printing nips and dryer, respectively, and the analysis of the mechanisms involved highlight the roles of the contacting surfaces and the relative liquid carrier properties of both non-image and printed image areas. The thesis includes laboratory studies on wetting of porous media in the form of coated paper and compressed pigment tablets by mono-, dual-, and multi-component liquids, and paper water/moisture content analysis in both offline and online conditions, thus also enabling direct sampling of temporal water/moisture profiles from multiple locations. One main focus in this thesis was to establish a measurement system which is able to monitor rapid changes in moisture content of paper. The study suggests that near-infrared diffuse reflectance spectroscopy can be used as a moisture sensitive system and to provide accurate online qualitative indicators, but, also, when accurately calibrated, can provide quantification of water/moisture levels, its distribution and dynamic liquid transfer. Due to the high sensitivity, samples can be measured with excellent reproducibility and good signal to noise ratio. Another focus of this thesis was on the evolution of the moisture content, i.e. changes in moisture content referred to (re)wetting, and liquid distribution during printing of coated paper. The study confirmed different wetting phases together with the factors affecting each phase both for a single droplet and a liquid film applied on a porous substrate. For a single droplet, initial capillary driven imbibition is followed by equilibrium pore filling and liquid retreat by evaporation. In the case of a liquid film applied on paper, the controlling factors defining the transportation were concluded to be the applied liquid volume in relation to surface roughness, capillarity and permeability of the coating giving the liquid uptake capacity. The printing trials confirmed moisture gradients in the printed sheet depending on process parameters such as speed, fountain solution dosage and drying conditions as well as the printed layout itself. Uneven moisture distribution in the printed sheet was identified to be one of the sources for waving appearance and the magnitude of waving was influenced by the drying conditions.

Pallomaisen rullalaakerin vauriotutkimus kartonkikoneen kiertoöljyvoidellulla kuivatusosalla

Tämä työ on tehty Stora Enson Imatran kartonkitehtaan kunnossapidosta vastaavalle Efora Oy:lle. Tavoitteena oli selvittää syy Imatran Kartonkikone 5:n kuivatussylinterien laakerivaurioiden suureen määrään verrattuna tehtaiden kolmeen muuhun kartonkikoneeseen. Tutkimuksissa keskityttiin laakerien käyttöolosuhteisiin. Syyn selvittämiseksi työssä vertailtiin eri kartonkikoneiden kiertoöljyvoitelujärjestelmiä, voiteluöljyjä, voiteluolosuhteita, öljyjen kuntoa ja kunnon seurantaa. Myös laakereihin kohdistuvia kuormia arvioitiin. Alan kirjallisuuden avulla on käyty läpi kartonkikoneen rakennetta ja toimintaa tarvittavassa laajuudessa, voitelun ja laakerin vaurioitumisen teoriaa sekä voiteluaineiden ominaisuuksien ja koostumuksen perusteita. Vertailevissa tutkimuksissa ei löytynyt vauriomäärien eroja selittäviä eroavaisuuksia Imatran tehtaiden eri kartonkikoneiden välillä, joskin Kartonkikone 5:n kiertovoiteluöljyn puhtaustaso oli muita Imatran kartonkikoneita heikompi. Laakerikuormien osalta havaittiin joidenkin laakerien käyvän laakerille asetetun vähimmäiskuorman alittavilla kuormituksilla. Vähimmäiskuormaa pienempi radiaalikuorma voi johtaa laakerin virheelliseen toimintaan ja edelleen vaurioitumiseen. Voiteluolosuhteet todettiin erittäin vaikeiksi ja niillä on epäilemättä vaikutusta voiteluöljyn ja laakerien lyhentyneeseen käyttöikään.

Paperin spraypäällystys

Tässä työssä esitellään paperin spraypäällystykseen soveltuvaa tekniikkaa sekä yleistä sprayteknologiaa ja teoriaa sen taustalla. Lisäksi käydään läpi pohjapaperilta vaadittuja ominaisuuksia ja käsitellään spraypäällystykseen sopivan pastan koostumusta.

Eri MAG-hitsausprosessien ja -parametrien vaikutus suurlujuusteräksestä valmistetun otsapienahitsin äärikestävyyteen, muodonmuutoskykyyn ja vauriomuotoon

Työssä tutkittiin Ruukki Oyj:n suorasammutetusta S960QC-teräksestä valmistetun kuormaakantavan levyjen ristiliitoksen pienahitsien lujuutta, muodonmuutoskykyä ja vaurioitumismekanismia laajaan kokeelliseen aineistoon perustuen. Tärkeimpänä muuttujana koematriisissa olivat eri MAG-hitsausprosessit. Perinteisen kuumakaarihitsauksen vertailukohteena oli Kemppi Oy:n uusi adaptiivinen valokaaren pituutta säätävä WiseFusion-hitsaustoiminto kuuma- ja pulssikaarihitsauksessa. Näiden kolmen hitsausprosessin rinnalla varioitiin erisuuruisia a-mittoja, eri hitsauslisäaineita ja hitsin erikylkisyyttä. Lisäksi juuritunkeuman estämisen vaikutusta hitsien käyttäytymiseen tutkittiin täydentävällä koesarjalla, jossa tunkeuman muodostuminen estettiin levyjen väliin asetetulla volframilevyllä. Työn perimmäisenä tavoitteena oli selvittää syy aiemmassa tutkimuksessa havaitulle pienahitsien vaurioitumiselle leikkautumalla sularajaa pitkin. Sularajan suhteellista pituutta saadaan kasvatettua estämällä hitsin juuritunkeuma ja absoluuttista pituutta saadaan lisää kateettipoikkeaman avulla. Lisäksi tutkimuksessa oli tarkoitus tuoda esille suurlujuusteräksisen liitoksen eri mitoituslähtökohdat (mm. lämmöntuonnin kontrollointi). Tämän vuoksi hitsausparametrit mitattiin jännitteen ja virran hetkellisiin arvoihin perustuen, jolloin kuuma- ja pulssikaarihitsauksen laskennalliset hitsaustehot ovat vertailukelpoisia. Koehitseistä valmistettiin hieet hitsien tarkan geometrian määrittämiseksi ja liitoksen mekaaniset ominaisuudet tutkittiin vetokokeella. Tulosten perusteella sularajavaurio aktivoituu pulssikaarella hitsatuissa koekappaleissa. Tämä aiheutunee pulssi- ja kuumakaarihitsauksen sularajan mikrorakenteiden eroavaisuudesta. Sularajavaurio näyttää huonontavan hitsien muodonmuutoskykyä, mutta jatkokokeita tuloksen verifioimiseksi on tehtävä. S960QC-teräkselle ominaisen pehmenneen vyöhykkeen vaurio ei aktivoitunut, vaikka Ruukin antamat jäähtymisaikasuositukset ylitettiin reilusti.

Efficacy of the d-phenothrin/pyriproxyfen association against mites in naturally co-infested rabbits

The aim of the present study was to evaluate the efficacy of the d-phenothrin/pyriproxyfen association against Psoroptes ovis, Cheyletiella parasitivorax, and Leporacarus gibbus infestations in naturally co-infested rabbits. Twenty crossbreed (New Zealand White x California) rabbits concurrently infested by the three mite species were randomly divided in two groups. All rabbits presented with hyperemia, erythema and formation of crusts in the ear canals caused by P. ovis. Infestations by both C. parasitivorax and L. gibbus were considered asymptomatic in all animals.Ten animals were treated with a 4.4% d-phenothrin and 0.148% pyriproxyfen spray formulation until have their body surface uniformly sprayed, including external ear canals. The other ten rabbits remained untreated, serving as control group. Observations were done on days +7, +14, +21, +28, and +35 post-treatment. The d-phenothrin/pyriproxyfen association showed 100% efficacy against the three mite species and was responsible for the remission of psoroptic mange lesions on treated animals. No signs of intoxication were observed. The results indicate that d-phenothrin/pyriproxyfen spray formulation in a single application is an effective and clinically safe option for the control of different mite infestations in rabbits.