Development of copper sulfide/cadmium sulfide thin film solar cell s : fourth technical progress report, April 13 - July 12, 1980 /

"Work Performed Under Contract No. AC02-77CH00178."

Thin film polycrystalline silicon solar cells : technical progress quarterly report no. 3 for March 25 - June 24, 1980 /

"Work Performed Under Contract No. AC02-77CH00178."

Thin-film polycrystalline silcon solar cells : quarterly technical progress report no. 3 for period April 1 - June 30, 1980 /

"Work Performed Under Contract No. AC02-77CH00178."

Thin film polycrystalline silicon solar cells : first technical progress report for April 15 - July 15, 1980.

"Work Performed Under Contract No. AC02-77CH00178."

Thin film polycrystalline silicon solar cells : second technical progress report for July 15 - October 15, 1980.

"Work Performed Under Contract No. AC02-77CH00178."

Indium phosphide/cadmium sulfide thin-film solar cells : quarterly report for period July - October 1980 /

"Work Performed Under Contract No. AC02-77CH00178."

MIS and P/N junction solar cells on thin-film polycrystalline silicon /

"Work Performed Under Contract No. EG-77-C-01-4042."

Electrochemical photovoltaic cells CdSe thin film electrodes : final report, June 1979-June 1980 /

"Contract No. AC02-77CH00178."

Indium phosphide/cadmium sulfide thin-film solar cells : final report for period May 1979 - July 1980 /

"Contract No. AC02-77CH00178."

Thin-film polycrystalline silcon solar cells : final technical report for the period October 1, 1979-September 30, 1980. /

"Contract No. AC02-77CH00178."

Thin-film polycrystalline silicon solar cells.

"Work Performed Under Contract No. ET-78-C-03-1876."

A new method of calibrating thin film gauge backing materials.

Mode of access: Internet.

Research and development of thin film vapor compression, saline water conversion system /

Mode of access: Internet.

An investigation of thin film magnetic recording media

Mechanical, physical and chemical changes in the surface of commercial thin film metal evaporated magnetic recording media have been correlated to recording error and signal degradation measurements. Modified and adapted commercial Hi-8 video recorders have been used for sample generation whilst analytical techniques such as SXPS,IMS and SEM have been employed in the surface characterisation. The durability of the media was assessed through stop motion (still frame) and cycling tests, where error growth and signal degradation were measured as a function of running time. The tests were performed under ambient (22°C, 40% RH) and high humidity (22°C, 80% RH) conditions. Characterisation of the lubricant layer on each tape was performed through models based on XPS and angle resolved XPS. The lubricant thickness can significantly affect the durability and signal output level of a thin film tape and thus it is important that reliable quantification can be achieved. Various models were considered for determining the lubricant thickness although ultimately, the most suitable technique was deemed to be a model that assumed a uniform layer structure. In addition to thin film metal evaporated media, equivalent durability tests and surface analysis experiments were performed using a commercial metal particle tape in order that comparisons could be made between the two types of recording media. The signal performance of the thin film metal evaporated media was found to be quite different from that for the metal particle tape since dropout errors and signal degradation increased at a much earlier stage. Extensive surface analyses enabled the mechanisms responsible for media failure and error growth to be identified in the ME and MP tapes and these were found to result from cyclic stressing and fatigue on the immediate substrate of the media.

Thin film bearings with phase change of lubricant

The possible evaporation of lubricant in fluid film bearings has been investigated theoretically and by experiment using a radial flow hydrostatic bearing supplied with liquid refrigerant R114. Good correlation between measured and theoretical values was obtained using a bespoke computational fluid dynamic model in which the flow was assumed to be laminar and adiabatic. The effects of viscous dissipation and vapour generation within the fluid film are fully accounted for by applying a fourth order Runge-Kutta routine to satisfy the radial and filmwise transverse constraints of momentum, energy and mass conservation. The results indicate that the radial velocity profile remains parabolic while the flow remains in the liquid phase and that the radial rate of enthalpy generation is then constant across the film at a given radius. The results also show that evaporation will commence at a radial location determined by geometry and flow conditions and in fluid layers adjacent to the solid boundaries. Evaporation is shown to progress in the radial direction and the load carrying capacity of such a bearing is reduced significantly. Expressions for the viscosity of the liquid/vapour mixture found in the literature survey have not been tested against experimental data. A new formulation is proposed in which the suitable choice of a characteristic constant yields close representation to any of these expressions. Operating constraints imposed by the design of the experimental apparatus limited the extent of the surface over which evaporation could be obtained, and prevented clear identification of the most suitable relationship for the viscosity of the liquid/vapour mixture. The theoretical model was extended to examine the development of two phase flow in a rotating shaft face seal of uniform thickness. Previous theoretical analyses have been based on the assumption that the radial velocity profile of the flow is always parabolic, and that the tangential component of velocity varies linearly from the value at the rotating surface, to zero at the stationary surface. The computational fluid dynamic analysis shows that viscous shear and dissipation in the fluid adjacent to the rotating surface leads to developing evaporation with a consequent reduction in tangential shear forces. The tangential velocity profile is predicted to decay rapidly through the film, exhibiting a profile entirely different to that assumed by previous investigators. Progressive evaporation takes place close to the moving wall and does not occur completely at a single radial location, as has been claimed in earlier work.