Análise topológica experimental por perfilometria cíclica indutiva de superficies de paredes estruturais

To enhance the maintenance practices, Oil and Gas Pipelines are inspected from the inside by automated systems called PIG (Pipeline Inspection Gauge). The inspection and mapping of defects, as dents and holes, in the internal wall of these pipelines are increasingly put into service toward an overall Structural Integrity Policy. The residual life of these structures must be determined such that minimize its probability of failure. For this reason, the investigation on the detection limits of some basic topological features constituted by peaks or valleys disposed along a smooth surface is of great value for determining the sensitivity of the measurements of defects from some combinations of circumferential, axial and radial extent. In this investigation, it was analyzed an inductive profilometric sensor to scan three races, radius r1, r2, r3, in a circular surface of low carbon steel, equipped with eight consecutive defects simulated by bulges and holes by orbit, equally spaced at p/4 rad. A test rig and a methodology for testing in laboratory were developed to evaluate the sensor response and identify their dead zones and jumps due to fluctuations as a function of topological features and scanning velocity, four speeds different. The results are presented, analyzed and suggestions are made toward a new conception of sensor topologies, more sensible to detect these type of damage morphologies

Medição e modelagem da resposta de um sensor de pig perfilométrico sob diferentes solicitações dinâmicas

Ensure the integrity of the pipeline network is an extremely important factor in the oil and gas industry. The engineering of pipelines uses sophisticated robotic inspection tools in-line known as instrumented pigs. Several relevant factors difficult the inspection of pipelines, especially in offshore field which uses pipelines with multi-diameters, radii of curvature accentuated, wall thickness of the pipe above the conventional, multi-phase flow and so on. Within this context, appeared a new instrumented Pig, called Feeler PIG, for detection and sizing of thickness loss in pipelines with internal damage. This tool was developed to overcome several limitations that other conventional instrumented pigs have during the inspection. Several factors influence the measurement errors of the pig affecting the reliability of the results. This work shows different operating conditions and provides a test rig for feeler sensors of an inspection pig under different dynamic loads. The results of measurements of the damage type of shoulder and holes in a cyclic flat surface are evaluated, as well as a mathematical model for the sensor response and their errors from the actual behavior

Desenvolvimento de sistemas de pastas leves para aplicação em cimentação de poços petrolíferos com baixo gradiente de fratura

All around the world, naturally occurring hydrocarbon deposits, consisting of oil and gas contained within rocks called reservoir rocks , generally sandstone or carbonate exists. These deposits are in varying conditions of pressure and depth from a few hundred to several thousand meters. In general, shallow reservoirs have greater tendency to fracture, since they have low fracture gradient, ie fractures are formed even with relatively low hydrostatic columns of fluid. These low fracture gradient areas are particularly common in onshore areas, like the Rio Grande do Norte basin. During a well drilling, one of the most favorable phases for the occurrence of fractures is during cementing, since the cement slurry used can have greater densities than the maximum allowed by the rock structure. Furthermore, in areas which are already naturally fractured, the use of regular cement slurries causes fluid loss into the formation, which may give rise to failures cementations and formation damages. Commercially, there are alternatives to the development of lightweight cement slurries, but these fail either because of their enormous cost, or because the cement properties were not good enough for most general applications, being restricted to each transaction for which the cement paste was made, or both reasons. In this work a statistical design was made to determine the influence of three variables, defined as the calcium chloride concentration, vermiculite concentration and nanosilica concentration in the various properties of the cement. The use of vermiculite, a low density ore present in large amounts in northeastern Brazil, as extensor for cementing slurries, enabled the production of stable cements, with high water/cement ratio, excellent rheological properties and low densities, which were set at 12.5 lb / gal, despite the fact that lower densities could be achieved. It is also seen that the calcium chloride is very useful as gelling and thickening agent, and their use in combination with nanosilica has a great effect on gel strength of the cement. Hydrothermal Stability studies showed that the pastes were stable in these conditions, and mechanical resistance tests showed values of the order of up to 10 MPa

Síntese de Fischer-Tropsch sobre perovskitas LayCu0,4Fe0,6O3

The current natural gas production of 52 Mm3d-1 and the large projects for its expansion has been setting new boundaries for the Brazilian industry of oil and gas. So far, one of the biggest challenges regards to the logistics for gas transportation from offshore fields. Therefore, the transformation of natural gas into gasoline, diesel and/or olefins via Fischer-Tropsch synthesis would be an alternative to this matter. In this work, the production of hydrocarbons by Fischer-Tropsch synthesis in a slurry reactor was investigated and a perovskite-type catalyst (LayCu0,4Fe0,6O3 ± d) was used with y varying from 0 to 1 on a molar basis. In addition, Nb2O5 support was also applied in order to observe the selectivity of the produced hydrocarbons by the Fischer-Tropsch process. It is shown that the hydrogen conversion was influenced by the support as well as the different phases of the samples. The kinetic results for the CO2 production suffered great influence with the introduction of the Nb2O5 support throughout the series of samples studied. The catalysts allowed obtaining welldefined cuts of hydrocarbons in the range of C1-C6 and C17-C28, and these results were clearly influenced by the support and the lanthanum content. The higher olefin/paraffin ratio obtained was 1.8 when using a non-supported perovskite with y equal to 0.8. This would indicate the suitability of using this material for the production of olefins

Bio-óleo e biogás da degradação termoquímica de lodo de esgoto doméstico em cilindro rotativo

The objective of this study was to produce biofuels (bio-oil and gas) from the thermal treatment of sewage sludge in rotating cylinder, aiming industrial applications. The biomass was characterized by immediate and instrumental analysis (elemental analysis, scanning electron microscopy - SEM, X-ray diffraction, infrared spectroscopy and ICP-OES). A kinetic study on non-stationary regime was done to calculate the activation energy by Thermal Gravimetric Analysis evaluating thermochemical and thermocatalytic process of sludge, the latter being in the presence of USY zeolite. As expected, the activation energy evaluated by the mathematical model "Model-free kinetics" applying techniques isoconversionais was lowest for the catalytic tests (57.9 to 108.9 kJ/mol in the range of biomass conversion of 40 to 80%). The pyrolytic plant at a laboratory scale reactor consists of a rotating cylinder whose length is 100 cm with capable of processing up to 1 kg biomass/h. In the process of pyrolysis thermochemical were studied following parameters: temperature of reaction (500 to 600 ° C), flow rate of carrier gas (50 to 200 mL/min), frequency of rotation of centrifugation for condensation of bio-oil (20 to 30 Hz) and flow of biomass (4 and 22 g/min). Products obtained during the process (pyrolytic liquid, coal and gas) were characterized by classical and instrumental analytical techniques. The maximum yield of liquid pyrolytic was approximately 10.5% obtained in the conditions of temperature of 500 °C, centrifugation speed of 20 Hz, an inert gas flow of 200 mL/min and feeding of biomass 22 g/min. The highest yield obtained for the gas phase was 23.3% for the temperature of 600 °C, flow rate of 200 mL/min inert, frequency of rotation of the column of vapor condensation 30 Hz and flow of biomass of 22 g/min. The non-oxygenated aliphatic hydrocarbons were found in greater proportion in the bio-oil (55%) followed by aliphatic oxygenated (27%). The bio-oil had the following characteristics: pH 6.81, density between 1.05 and 1.09 g/mL, viscosity between 2.5 and 3.1 cSt and highest heating value between 16.91 and 17.85 MJ/ kg. The main components in the gas phase were: H2, CO, CO2 and CH4. Hydrogen was the main constituent of the gas mixture, with a yield of about 46.2% for a temperature of 600 ° C. Among the hydrocarbons formed, methane was found in higher yield (16.6%) for the temperature 520 oC. The solid phase obtained showed a high ash content (70%) due to the abundant presence of metals in coal, in particular iron, which was also present in bio-oil with a rate of 0.068% in the test performed at a temperature of 500 oC.

Integração dos processos de flotação e foto-fenton para redução de óleos e graxas de água produzida em campos de petróleo

During production of oil and gas, there is also the production of an aqueous effluent called produced water. This byproduct has in its composition salts, organic compounds, gases and heavy metals. This research aimed to evaluate the integration of processes Induced Air Flotation (IAF) and photo-Fenton for reducing the Total Oils and Greases (TOG) present in produced water. Experiments were performed with synthetic wastewater prepared from the dispersion of crude oil in saline solution. The system was stirred for 25 min at 33,000 rpm and then allowed to stand for 50 min to allow free oil separation. The initial oil concentration in synthetic wastewater was 300 ppm and 35 ppm for the flotation and the photo-Fenton steps, respectively. These values of initial oil concentration were established based on average values of primary processing units in Potiguar Basin. The processes were studied individually and then the integration was performed considering the best experimental conditions found in each individual step. The separation by flotation showed high removal rate of oil with first-order kinetic behavior. The flotation kinetics was dependent on both the concentration and the hydrophilic-lipophilic balance (HLB) of the surfactant. The best result was obtained for the concentration of 4.06.10-3 mM (k = 0.7719 min-1) of surfactant EO 2, which represents 86% of reduction in TOG after 4 min. For series of surfactants evaluated, the separation efficiency was found to be improved by the use of surfactants with low HLB. Regarding the TOG reduction step by photo-Fenton, the largest oil removal reached was 84% after 45 min of reaction, using 0.44 mM and 10 mM of ferrous ions and hydrogen peroxide, respectively. The best experimental conditions encountered in the integrated process was 10 min of flotation followed by 45 min of photo-Fenton with overall TOG reduction of 99%, which represents 5 ppm of TOG in the treated effluent. The integration of processes flotation and photo-Fenton proved to be highly effective in reducing TOG of produced water in oilfields

Caracterização química e toxicológica da água produzida descartada em plataformas de óleo e gás na costa brasileira e seu comportamento dispersivo no mar

The production of oil and gas is usually accompanied by the production of water, also known as produced water. Studies were conducted in platforms that discharge produced water in the Atlantic Ocean due to oil and gas production by Petrobras from 1996 to 2006 in the following basins: Santos (Brazilian south region), Campos (Brazilian southeast region) and Ceara (Brazilian northeast region). This study encompasses chemical composition, toxicological effects, discharge volumes, and produced water behavior after releasing in the ocean, including dispersion plumes modeling and monitoring data of the marine environment. The concentration medians for a sampling of 50 samples were: ammonia (70 mg L-1), boron (1.3 mg L1), iron (7.4 mg L-1), BTEX (4.6 mg L-1), PAH (0.53 mg L-1), TPH (28 mg L-1); phenols (1.3 mg L-1) and radioisotopes (0.15 Bq L-1 for 226Ra and 0.09 Bq L-1 for 228Ra). The concentrations of the organic and inorganic parameters observed for the Brazilian platforms were similar to the international reference data for the produced water in the North Sea and in other regions of the world. It was found significant differences in concentrations of the following parameters: BTEX (p<0.0001), phenols (p=0.0212), boron (p<0.0001), iron (p<0.0001) and toxicological response in sea urchin Lytechinus variegatus (p<0.0001) when considering two distinguished groups, platforms from southeast and northeast Region (PCR-1). Significant differences were not observed among the other parameters. In platforms with large gas production, the monoaromatic concentrations (BTEX from 15.8 to 21.6 mg L-1) and phenols (from 2 to 83 mg L-1) were higher than in oil plataforms (median concentrations of BTEX were 4.6 mg L-1 for n=53, and of phenols were 1.3 mg L-1 for n=46). It was also conducted a study about the influence of dispersion plumes of produced water in the vicinity of six platforms of oil and gas production (P-26, PPG-1, PCR-1, P-32, SS-06), and in a hypothetical critical scenario using the chemical characteristics of each effluent. Through this study, using CORMIX and CHEMMAP models for dispersion plumes simulation of the produced water discharges, it was possible to obtain the dilution dimension in the ocean after those discharges. The dispersion plumes of the produced water modelling in field vicinity showed dilutions of 700 to 900 times for the first 30-40 meters from the platform PCR-1 discharge point; 100 times for the platform P-32, with 30 meters of distance; 150 times for the platform P-26, with 40 meters of distance; 100 times for the platform PPG-1, with 130 meters of distance; 280 to 350 times for the platform SS-06, with 130 meters of distance, 100 times for the hypothetical critical scenario, with the 130 meters of distance. The dilutions continue in the far field, and with the results of the simulations, it was possible to verify that all the parameters presented concentrations bellow the maximum values established by Brazilian legislation for seawater (CONAMA 357/05 - Class 1), before the 500 meters distance of the discharge point. These results were in agreement with the field measurements. Although, in general results for the Brazilian produced water presented toxicological effects for marine organisms, it was verified that dilutions of 100 times were sufficient for not causing toxicological responses. Field monitoring data of the seawater around the Pargo, Pampo and PCR-1 platforms did not demonstrate toxicity in the seawater close to these platforms. The results of environmental monitoring in seawater and sediments proved that alterations were not detected for environmental quality in areas under direct influence of the oil production activities in the Campos and Ceara Basin, as according to results obtained in the dispersion plume modelling for the produced water discharge

Caracterização química e toxicológica da água produzida descartada em plataformas de óleo e gás na costa brasileira e seu comportamento dispersivo no mar

The production of oil and gas is usually accompanied by the production of water, also known as produced water. Studies were conducted in platforms that discharge produced water in the Atlantic Ocean due to oil and gas production by Petrobras from 1996 to 2006 in the following basins: Santos (Brazilian south region), Campos (Brazilian southeast region) and Ceara (Brazilian northeast region). This study encompasses chemical composition, toxicological effects, discharge volumes, and produced water behavior after releasing in the ocean, including dispersion plumes modeling and monitoring data of the marine environment. The concentration medians for a sampling of 50 samples were: ammonia (70 mg L-1), boron (1.3 mg L1), iron (7.4 mg L-1), BTEX (4.6 mg L-1), PAH (0.53 mg L-1), TPH (28 mg L-1); phenols (1.3 mg L-1) and radioisotopes (0.15 Bq L-1 for 226Ra and 0.09 Bq L-1 for 228Ra). The concentrations of the organic and inorganic parameters observed for the Brazilian platforms were similar to the international reference data for the produced water in the North Sea and in other regions of the world. It was found significant differences in concentrations of the following parameters: BTEX (p<0.0001), phenols (p=0.0212), boron (p<0.0001), iron (p<0.0001) and toxicological response in sea urchin Lytechinus variegatus (p<0.0001) when considering two distinguished groups, platforms from southeast and northeast Region (PCR-1). Significant differences were not observed among the other parameters. In platforms with large gas production, the monoaromatic concentrations (BTEX from 15.8 to 21.6 mg L-1) and phenols (from 2 to 83 mg L-1) were higher than in oil plataforms (median concentrations of BTEX were 4.6 mg L-1 for n=53, and of phenols were 1.3 mg L-1 for n=46). It was also conducted a study about the influence of dispersion plumes of produced water in the vicinity of six platforms of oil and gas production (P-26, PPG-1, PCR-1, P-32, SS-06), and in a hypothetical critical scenario using the chemical characteristics of each effluent. Through this study, using CORMIX and CHEMMAP models for dispersion plumes simulation of the produced water discharges, it was possible to obtain the dilution dimension in the ocean after those discharges. The dispersion plumes of the produced water modelling in field vicinity showed dilutions of 700 to 900 times for the first 30-40 meters from the platform PCR-1 discharge point; 100 times for the platform P-32, with 30 meters of distance; 150 times for the platform P-26, with 40 meters of distance; 100 times for the platform PPG-1, with 130 meters of distance; 280 to 350 times for the platform SS-06, with 130 meters of distance, 100 times for the hypothetical critical scenario, with the 130 meters of distance. The dilutions continue in the far field, and with the results of the simulations, it was possible to verify that all the parameters presented concentrations bellow the maximum values established by Brazilian legislation for seawater (CONAMA 357/05 - Class 1), before the 500 meters distance of the discharge point. These results were in agreement with the field measurements. Although, in general results for the Brazilian produced water presented toxicological effects for marine organisms, it was verified that dilutions of 100 times were sufficient for not causing toxicological responses. Field monitoring data of the seawater around the Pargo, Pampo and PCR-1 platforms did not demonstrate toxicity in the seawater close to these platforms. The results of environmental monitoring in seawater and sediments proved that alterations were not detected for environmental quality in areas under direct influence of the oil production activities in the Campos and Ceara Basin, as according to results obtained in the dispersion plume modelling for the produced water discharge

Um monitor de metadados de QoS e QoC para plataformas de middleware

Context-aware applications are typically dynamic and use services provided by several sources, with different quality levels. Context information qualities are expressed in terms of Quality of Context (QoC) metadata, such as precision, correctness, refreshment, and resolution. On the other hand, service qualities are expressed via Quality of Services (QoS) metadata such as response time, availability and error rate. In order to assure that an application is using services and context information that meet its requirements, it is essential to continuously monitor the metadata. For this purpose, it is needed a QoS and QoC monitoring mechanism that meet the following requirements: (i) to support measurement and monitoring of QoS and QoC metadata; (ii) to support synchronous and asynchronous operation, thus enabling the application to periodically gather the monitored metadata and also to be asynchronously notified whenever a given metadata becomes available; (iii) to use ontologies to represent information in order to avoid ambiguous interpretation. This work presents QoMonitor, a module for QoS and QoC metadata monitoring that meets the abovementioned requirement. The architecture and implementation of QoMonitor are discussed. To support asynchronous communication QoMonitor uses two protocols: JMS and Light-PubSubHubbub. In order to illustrate QoMonitor in the development of ubiquitous application it was integrated to OpenCOPI (Open COntext Platform Integration), a Middleware platform that integrates several context provision middleware. To validate QoMonitor we used two applications as proofof- concept: an oil and gas monitoring application and a healthcare application. This work also presents a validation of QoMonitor in terms of performance both in synchronous and asynchronous requests

Evolução da paisagem do baixo curso do rio de Piranhas-Assu (1988-2024): uso de autômatos celulares em modelo dinâmico espacial para simulação de cenários futuros

The lower course of Piranhas-Assu river, located in the north coast of Rio Grande do Norte, Brazil, arouses a keen interest as a study field, once it concentrates, besides petroleum and gas exploration, activities related to shrimp culture, salt and horticulture, factors that also deserve special attention. Thus, the awareness of the study field environmental stage demands studies from researchers and discernment from society, as a way of understanding the inter-relation between environment and men. Therefore, this work attempts at understanding and studying the dynamics of land use in the lower course of Piranhas-Assu river, through a multitemporal analysis of present and past, accomplishing future projections through simulation models. The work is divided in stages that include the research, analysis, interpretation of results, and the generation of simulation models, to analyze the landscape tendencies, making possible to identify indicators which cause such changes in the lower course of the river. From Geographical Database, the necessary exploratory analyses were accomplished to the following items: land use evolution, natural and environmental vulnerability, multiple geodiversity indexes, and preparation of the data to be used in the simulation model. Later, the construction of the landscape simulation model was conducted. Sequentially, simulations of future sceneries were accomplished through the execution of the model in a specific software environment. Last, the analyses of landscape tendencies in the study field were carried out. The lower course of Piranhas-Assu River didn't show any intense dynamics in landscape changing, once in the period taken into account (from 1988 to 2004) class stability proved to be superior to its transformations. Activities related to agriculture and livestock are the ones that influence, mostly, the landscape dynamics. The production of sea shrimp and petroleum also infers in the landscape, although in smaller proportion. INCRA s public policies excessively determined the dynamics of the landscape in the lower course of Piranhas-Assu River, RN. In respect to its natural vulnerability, the lower course of Piranhas-Assu River, RN, features more vulnerable than stable areas. The landscape simulation, in the first taken period (2004-2009), indicated considerable increases and decreases of antropic activities, if compared to its sequent periods (2009-2014, 2014-2019 and 2019-2024). The simulation, in a wider analysis, showed that the determining factors for the space mobility of antropic activities, in the focused area, are related to the pre-existence of communities with agricultural capability and to the existence of access routes and drainage. Considering the area that features fixed and mobile dunes, located in Porto do Mangue district, we recommend its conversion into a conservation area

O circuito espacial da produção petrolífera no rio Grande do Norte

Our study refers to the state of Rio Grande do Norte against the deployment of oil activity in their territory. In this sense the aim of this work was to analyze the presence of the loop space of the oil production system linked to objects and actions on the Rio Grande do Norte territory. From the so-called "oil shock", an event that caused global developments in several countries, Petróleo Brasileiro S/A (PETROBRAS) increased investments in drilling geological basins in Brazil. In the year 1973 was drilled in the sea area well which led to commercial production of oil and gas in Rio Grande do Norte. From that point on were added in some parts of the Potiguar territory, large systems of coupled objects to actions caused by several agents. In this context, geographic situations have been reorganized due to an unprecedented space circuit production accompanied by a new circle of cooperation. In the state happen all instances of the circuit: the production, distribution and consumption. In light of the theory of the geographical area seek to direct our thoughts to the operation of these bodies, and they are linked to material and immaterial flows multiscales. This perspective allows us to think the territory of Rio Grande do Norte entered into a new territorial division of labor characterized by specialization regional production. Oil activity was implemented in the territory of Rio Grande do Norte at a time marked by productive restructuring of various economic sectors. The oil sector has been acting increasingly linked the scientific and informational, with a view to increasing productivity. The presence of this circuit demanded the territory, specifically the Mossoró, an organizational structure that is different from the vast system nationally integrated private commercial corporations to small corporations, all of them relating directly or indirectly to PETROBRAS. The flows between companies whose headquarters are located in distant states and even countries have generated a continuous movement of goods, people, information and ideas, which is also causing new materialities in the territory

Digital radiography for the inspection of weld seams of pipelines - better sensitivity

Conventional radiography, using industrial radiographic films, has its days numbered. Digital radiography, recently, has taken its place in various segments of products and services, such as medicine, aerospace, security, automotive, etc. As well as the technological trend, the digital technique has brought proven benefits in terms of productivity, sensitivity, the environment, tools for image treatment, cost reductions, etc. If the weld to be inspected is on a serried product, such as, for example, a pipe, the best option for the use of digital radiography is the plane detector, since its use can reduce the length of the inspection cycle due to its high degree of automation. This work tested welded joints produced with the submerged arc process, which were specially prepared in such a way that it shows small artificial cracks, which served as the basis forcomparing the sensitivity levels of the techniques involved. After carrying out the various experiments, the digital meth odshowed the highest sensitivity for the image quality indicator (IQI) of the wire and also in terms of detecting small discontinuities, indicating that the use of digital radiography using the plane detector had advantages over the conventional technique (Moreira et al. Digital radiography, the use of plane detectors for the inspection of welds in oil pipes and gas pipes.9th COTEQ and XXV National Testing Congress for Non Destructive Testing and Inspection; Salvador, Bahia, Brazil and Bavendiek et al. New digital radiography procedure exceeds film sensitivity considerably in aerospace applications. ECNDT; 2006; Berlin). The works were carried out on the basis of the specifications for oil and gas pipelines, API 5L 2004 edition (American Petroleum Institute. API 5L: specification for line pipe. 4th ed. p. 155; 2004) and ISO 3183 2007 edition (International Organization for Standardization, ISO 3183. Petroleum and gas industries - steel pipes for pi pelines transportation systems. p. 143; 2007). © 2010 Taylor & Francis.

Analise de tensões com ultrassom em tubos soldados por resistência elétrica

Pós-graduação em Engenharia Mecânica - FEG

Procedimentos de coletas de óleo para análise preditiva de turbinas à gás

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

The international trade position of Argentina. Towards a process of export diversification?

Includes bibliography.