CeO2-promoted Ni/activated carbon catalysts for the water–gas shift (WGS) reaction

The low temperature water–gas shift (WGS) reaction has been studied over carbon-supported nickel catalysts promoted by ceria. To this end, cerium oxide has been dispersed (at different loadings: 10, 20, 30 and 40 wt.%) on the activated carbon surface with the aim of obtaining small ceria particles and a highly available surface area. Furthermore, carbon- and ceria-supported nickel catalysts have also been studied as references. A combination of N2 adsorption analysis, powder X-ray diffraction, temperature-programmed reduction with H2, X-ray photoelectron spectroscopy and TEM analysis were used to characterize the Ni–CeO2 interactions and the CeO2 dispersion over the activated carbon support. Catalysts were tested in the low temperature WGS reaction with two different feed gas mixtures: the idealized one (with only CO and H2O) and a slightly harder one (with CO, CO2, H2, and H2O). The obtained results show that there is a clear effect of the ceria loading on the catalytic activity. In both cases, catalysts with 20 and 10 wt.% CeO2 were the most active materials at low temperature. On the other hand, Ni/C shows a lower activity, this assessing the determinant role of ceria in this reaction. Methane, a product of side reactions, was observed in very low amounts, when CO2 and H2 were included in the WGS feed. Nevertheless, our data indicate that the methanation process is mainly due to CO2, and no CO consumption via methanation takes place at the relevant WGS temperatures. Finally, a stability test was carried out, obtaining CO conversions greater than 40% after 150 h of reaction.

Activated Carbons Impregnated with Na2S and H2SO4: Texture, Surface Chemistry and Application to Mercury Removal from Aqueous Solutions

The effects of treatment of an activated carbon with Sulphur precursors on its textural properties and on the ability of the complex synthesized for mercury removal in aqueous solutions are studied. To this end, a commercial activated carbon has been modified by treatments with aqueous solutions of Na2S and H2SO4 at two temperatures (25 and 140 °C) to introduce sulphur species on its surface. The prepared adsorbents have been characterized by N2 (-196 °C) and CO2 (0 °C) adsorption, thermogravimetric analysis, temperature-programmed decomposition and X-ray photoelectron spectroscopy, and their adsorption capacities to remove Hg(II) ions in aqueous solutions have been determined. It has been shown that the impregnation treatments slightly modified the textural properties of the samples, with a small increase in the textural parameters (BET surface area and mesopore volumes). By contrast, surface oxygen content was increased when impregnation was carried out with Na2S, but it decreased when H2SO4 was used. However, the main effect of the impregnation treatments was the formation of surface sulphur complexes of thiol type, which was only achieved when the impregnation treatments were carried out at low temperature (25 °C). The presence of surface sulphur enhances the adsorption behaviour of these samples in the removal of Hg(II) cations in aqueous solutions at pH 2. In fact, complete Hg(II) removal is only obtained with the sulphur-containing activated carbons.

Chemical compositions of rocks and minerals from an underwater volcano of the Kuril deep-sea basin

Mineralogy and geochemistry of low-temperature hydrothermal manifestations occurring on the surface of basalts and in their cracks within a submarine volcano in the north-eastern part of the Kuril deep-sea basin have been studied. The following order of isolation of mineral phases has been found out: Fe-rich sulphides (pyrite) - Fe-rich layered silicates (hydromica of celadonite-nontronite type) - amorphous silica (opal) - Fe-oxyhydroxides (goethite) - Mn-oxyhydroxides (vernadite). Sulphide mineralization is of the phenocryst-stockwork type. Finding of pure barite fragments does not exclude presence of hydrothermal exhalations (smokers) on this volcanic structure.

Petrography, chemistry and magnetic properties of ODP Leg 115 basalts

A detailed study of the Fe-Ti oxides in four basalt samples-one from each of the four holes drilled into basement on Ocean Drilling Program Leg 115 (Sites 706, 707, 713, and 715) has been performed. Ilmenite is present only in samples from Sites 706 and 715. In the sample from Site 715, Ti-magnetite intergrowths are characteristic of subaerial (?) high-temperature oxy-exsolution; Ti-magnetite in the other three samples has experienced pervasive low-temperature oxidation to Ti-maghemite, as evidenced by the double-humped, irreversible, saturation magnetization vs. temperature (Js/T) curves. The bulk susceptibility of these samples, which are similar in terms of major element chemistry, varies by a factor of ~20 and correlates semiquantitatively with the modal abundance of Fe-Ti spinel, as determined by image analysis with an electron microprobe. The variation in Fe-Ti oxide abundance correlates with average grain size: fine-grained samples contain less Fe-Ti oxide. This prompts the speculation that the crystallization rate may also influence Fe-Ti oxide abundance.

Sulfur isotope rations in oceanic basement samples

Low temperature alteration of oceanic basement rocks is characterized by net gain of sulfur, which commonly yields low d34S values, suggesting involvement of microbial sulfate reduction. In order to test whether secondary sulfide minerals are consistent with a biogenic source, we apply high precision multiple sulfur isotope analysis to bulk rock sulfide and pyrite isolates from two contrasting types of altered oceanic basement rocks, namely serpentinized peridotites and altered basalts. Samples from two peridotite sites (Iberian Margin and Hess Deep) and from a basalt site on the eastern flank of the Juan de Fuca Ridge yield overlapping d34S values ranging from 0 per mil to -44 per mil. In contrast, sulfides in the basalt site are characterized by relatively low D33S values ranging from -0.06 per mil to 0.04 per mil, compared to those from peridotite sites (0.00 per mil to 0.16 per mil). The observed D33S signal is significant considering the analytical precision of 0.014 per mil (2 sigma). We present a batch reaction model that uses observed d34S and D33S relationships to quantify the effect of closed system processes and constrain the isotope enrichment factor intrinsic to sulfate reduction. The estimated enrichment factors as large as 61 per mil and 53 per mil, for peridotite and basalt sites respectively, suggest the involvement of microbial sulfate reduction. The relatively high D33S values in the peridotite sites are due to sulfate reduction in a closed system environment, whereas negative D33S values in the basalt site reflect open system sulfate reduction. A larger extent of sulfate reduction during alteration of peridotite to serpentinite is consistent with its higher H2 production capacity compared to basalt alteration, and further supports in-situ microbial sulfate reduction coupled with H2 production during serpentinization reactions.

In situ measurements of hydrogen sulfide, oxygen, and temperature in diffuse fluids of the ultramafic-hosted Logatchev hydrothermal vent field (Mid-Atlantic Ridge)

The Logatchev hydrothermal vent field (14°45'N, Mid-Atlantic Ridge) is located in a ridge segment characterized by mantle-derived ultramafic outcrops. Compared to basalt-hosted vents, Logatchev high temperature fluids are relatively low in sulfide indicating that the diffuse, low temperature fluids of this vent field may not contain sufficient sulfide concentrations to support a chemosymbiotic invertebrate community. However, the high abundances of bathymodiolin mussels with bacterial symbionts related to free-living sulfur oxidizing bacteria suggested that bioavailable sulfide is present at Logatchev. To clarify if diffuse fluids above mussel beds of Bathymodiolus puteoserpentis provide the reductants and oxidants needed by their symbionts for aerobic sulfide oxidation, in situ microsensor measurements of dissolved hydrogen sulfide and oxygen were combined with simultaneous temperature measurements. High temporal fluctuations of all three parameters were measured above the mussel beds. H2S and O2 co-existed with mean concentrations between 9-31 µM (H2S) and 216-228 µM (O2). Temperature maxima (<= 7.4°C) were generally concurrent with H2S maxima (<= 156 µM) and O2 minima (>= 142 µM). Long-term measurements for 250 days using temperature as a proxy for oxygen and sulfide concentrations indicated that the mussels were neither oxygen- nor sulfide-limited. Our in situ measurements at Logatchev indicate that sulfide may also be bioavailable in diffuse fluids from other ultramafic-hosted vents along slow- and ultraslow-spreading ridges.

(Table 4) Chemistry of iron-rich basalts from ODP Hole 106-648B

Analysis numbers 344-370, SAMF 12.5-12.7; 442-369, SAMF 12.7-12.9; 422-77, SAMF 12.9-13.1; 95-156, SAMF 13.1-13.3; 272-82, SAMF 13.3-13.5; 285-33, SAMF 13.5-13.7. Analyses are listed in depth order within each SAMF division.

(Table 2) Geochemistry at DSDP Holes 62-464 and 62-465A

Igneous rocks were recovered from three sites on Hess Rise during Deep Sea Drilling Project Leg 62: altered basalt at Site 464, at the northern end of Hess Rise; and altered trachyte from Site 465, and rounded basalt pebbles in upper Albian to middle Miocene sediments from Site 466, both at the southern end of Hess Rise. Major-, minor-, and trace-element data for basalt from Hole 464 are consistent with these rocks being transitional tholeiites that have undergone low-temperature alteration by reaction with sea water. Trachyte from Hole 465A exhibits as many as three generations of plagioclase along with potash feldspar that are flow aligned in groundmasses alterted to smectites and random mixed-layer clays. Textural evidence indicates that these rocks were eruped subaerially. Chemical data show a range of values when plotted on two- and three-component variation diagrams. The observed variations may result in part from differentiation, but they also reflect the high degree of alteration. Several oxides and elements show strong correlation with H2O+: K2O, SiO2, Rb and Lu decrease and MgO increases with increasing H2O+. These trends, except for that of Lu, are consistent with experimentally determined changes in chemistry that accompany alteration. The trend for Lu has not been previously reported; it may result from a more-intense alteration of the HREE-rich mafic minerals than of the LREE-rich feldspars. Despite their alteration, the trachytes compare favorably with alkalic differentiates from oceanic islands. We interpret Hess Rise as a volcanic platform formed by eruption of off-ridge volcanic rocks onto MORB oceanic crust during the Aptian and Albian stages, after the basement had migrated away from the spreading center. By analogy with present oceanic islands, we propose that early tholeiitic basalts were followed by alkalic basalts and their differentiation products (trachytes), producing a volcanic archipelago of islands and seamounts. Subsequent tectonism and subsidence led to the present state of Hess Rise.

Paleomagnetic and rock magnetic properties of ODP Leg 173 sites, west Iberia continental margin

We present detailed paleomagnetic and rock magnetic results of rock samples recovered during Leg 173. The Leg 173 cores display a multicomponent magnetization nature. Variations in magnetic properties correlate with changes in lithology that result from differences in the abundance and size of magnetic minerals. The combined investigation suggests that the magnetic properties of the "fresher" peridotite samples from Site 1070 are controlled mainly by titanomagnetite, with a strong Verwey transition in the vicinity of 110 K, and with field- and frequency-dependent susceptibility curves that resemble those of titanomagnetites. These results are in excellent agreement with thermomagnetic characteristics where titanomagnetites with Curie temperature ~580°C were identified from the "fresher" peridotites. In contrast to the magnetic properties observed from the "fresher" peridotites, the low-temperature curves for the "altered" peridotites did not show any Verwey transition. Thermomagnetic analysis using the high-temperature vibrating sample magnetometer also failed to show evidence for titanomagnetites. The remanent magnetization is carried by a thermally unstable mineral that breaks down at ~420°C, probably maghemite. The field- and frequency-dependent relationships are also directly opposite to those in the reversal zone, with no signs of titanomagnetite characteristics. Altogether, these rock magnetic data seem to be sensitive indicators of alteration and support the contention that maghemite is responsible for the magnetic signatures displayed in the altered peridotites of the upper section. The magnetic minerals of the basement rocks from Sites 1068, 1069, and 1070 are of variable particle size but fall within the pseudo-single-domain size range (0.2-14 µm). The average natural remanent magnetization (NRM) intensity of recovered serpenitinized peridotite is typically on the order of 20 mA/m for samples from Site 1068, but ~120 mA/m for samples from Site 1070. The much stronger magnetization intensity of Site 1070 is apparently in excellent agreement with the observed magnetic anomaly high. Nearly half of the NRM intensity remained after 400°C demagnetization, suggesting that the remanence can contribute significantly to the marine magnetic anomaly.

Stable oxygen, hydrogene and chlorine isotopes of mid-Atlantic abyssal peridotites

Serpentinized abyssal peridotites sampled by the Ocean Drilling Program Leg 209 along the mid-Atlantic Ridge near the 15°20'N Fracture Zone have been analyzed for oxygen, hydrogen, and chlorine isotope compositions in order to determine isotopic behavior under a wide range of serpentinization conditions and place constraints on fluid history. Oxygen and hydrogen thermometry suggests peak serpentinization temperatures of 300-500°C. Serpentine separates have low deltaD values possibly due to a magmatic fluid component or low-temperature exchange during seafloor weathering. Chlorine geochemistry focused on three holes: 1274A and 1272A (serpentinized peridotites) and 1268A (serpentinite locally altered to talc). Concentrations of both, water-soluble chloride (WSC) and structurally bound chloride (SBC) are significantly lower at Hole 1268A compared to Holes 1274A and 1272A. The delta37Cl values for WSC and SBC of serpentinites in Holes 1274A and 1272A are slightly positive (avg. WSC = 0.20 per mil, n = 22 and avg. SBC = 0.35 per mil, n = 22), representing typical seawater-hydration conditions commonly determined for abyssal peridotite. The SBC of serpentinites from Hole 1268A are also positive (avg. = 0.63 per mil); whereas, the SBC in talc-dominated samples is negative (avg. = -1.22 per mil). The WSC of both talc- and serpentine-dominated samples are also negative (avg. = -0.15 per mil). We interpret the chlorine isotope data to preserve a record of multiple fluid events. As seawater hydrated the peridotite, 37Cl was preferentially incorporated into the forming serpentine and water-soluble salts, yielding similar delta37Cl values on a regional scale as sampled by Holes 1268A, 1274A and 1272A. The resultant pore fluid was left depleted in 37Cl. Locally (Hole 1268A), this evolved fluid was remobilized possibly due to the initiation of hydrothermal circulation in response to emplacement of a mafic magma body. The low delta37Cl pore fluids attained elevated SiO2 and sulfur concentrations due to interaction with the gabbroic intrusion and, when ascending through the surrounding serpentinite, caused formation of isotopically negative talc. This secondary fluid also flushed the preserved serpentinite of its previously formed salts, resulting in negative delta37Cl WSC values. The delta37Cl SBC values of the serpentinite samples remained unmodified by reaction with the secondary fluid.

Chemical and isotopic compositions of pore fluids from ODP Sites 169-1034 and 169-1037

We have analysed the concentrations of Li, K, Rb, Cs, and B, and the isotopic ratios of Li and B of a suite of pore fluids recovered from ODP Sites 1037 (Leg 169; Escanaba Trough) and 1034 (Leg 169S; Saanich Inlet). In addition, we have analysed dissolved K, Rb, and Cs concentrations for estuarine mixing of the Ganges-Brahmaputra river system. Together, these data sets have been used to assess the role of sediments in the marine geochemical cycles of the alkali elements and boron. Uptake onto clay minerals during estuarine mixing removes 20-30% of the riverine input of dissolved Cs and Rb to the oceans. Prior to this study, the only other recognised sink of Rb and Cs was uptake during low-temperature alteration of the oceanic crust. Even with this additional sink there is an excess of inputs over outputs in their modern oceanic mass balance. Pore fluid data show that Li and Rb are transferred into marine sediments during early diagenesis. However, modeling of the Li isotope systematics of the pore fluids from Site 1037 shows that seawater Li taken up during marine sedimentation can be readily returned to solution in the presence of less hydrated cations, such as NH4+. This process also appears to result in high concentrations of pore fluid Cs (relative to local seawater) due to expulsion of adsorbed Cs from cation exchange sites. Flux calculations based on pore fluid data for a series of ODP sites indicate that early diagenesis of clay sediments removes around 8% of the modern riverine input of dissolved Li. Although NH4+-rich fluids do result in a flux of Cs to the oceans, on the global scale this input only augments the modern riverine Cs flux by ~3%. Nevertheless, this may have implications for the fate of radioactive Cs in the natural environment and waste repositories.

Chemistry of very young basalts from ODP Hole 106-648B

Basalts in Hole 648B, located in the rift valley of the Mid-Atlantic Ridge at 23°N in crust estimated to be less than 100,000 years old, are mainly fresh, but small amounts of secondary phases are found on fracture surfaces and in alteration halos within the rocks. The halos are defined by dark bands 1-4 mm thick that have developed parallel to fracture surfaces or pillow margins and which in some cases have migrated some centimeters into the rock. The dark bands are the principal locus of secondary phases. The secondary phases are olive-green and yellow protoceladonites, of composition and structure intermediate between celadonite and iron-rich saponite, red (Mn-poor) to opaque (Mn-rich) iron oxyhydroxides, mixtures of protoceladonite and iron oxyhydroxide, and rare manganese oxides. These phases occur mainly as linings or fillings of open spaces in the basalt within the dark bands. Sulfides and intersertal glass are the only primary phases that can be seen to have been altered. Where dark bands have migrated into the rock, the rock behind the advancing band is almost devoid of secondary phases, implying redissolution. The potassium and magnesium in the secondary phases could have been supplied from ambient seawater. The aluminum in the protoceladonites must have been derived from local reaction of intergranular glass. The source of iron and silica could have been intergranular glass or low temperature mineralizing solutions of the type responsible for the formation of deposits of manganese oxides and iron oxyhydroxides and silicates on the seafloor.

Major and trace element concentration of melt inclusions from Zhupanovsky volcano, Kamchatka

The paper presents data on naturally quenched melt inclusions in olivine (Fo 69-84) from Late Pleistocene pyroclastic rocks of Zhupanovsky volcano in the frontal zone of the Eastern Volcanic Belt of Kamchatka. The composition of the melt inclusions provides insight into the latest crystallization stages (~70% crystallization) of the parental melt (~46.4 wt % SiO2, ~2.5 wt % H2O, ~0.3 wt % S), which proceeded at decompression and started at a depth of approximately 10 km from the surface. The crystallization temperature was estimated at 1100 ± 20°C at an oxygen fugacity of deltaFMQ = 0.9-1.7. The melts evolved due to the simultaneous crystallization of olivine, plagioclase, pyroxene, chromite, and magnetite (Ol: Pl: Cpx : (Crt-Mt) ~ 13 : 54 : 24 : 4) along the tholeiite evolutionary trend and became progressively enriched in FeO, SiO2, Na2O, and K2O and depleted in MgO, CaO, and Al2O3. Melt crystallization was associated with the segregation of fluid rich in S-bearing compounds and, to a lesser extent, in H2O and Cl. The primary melt of Zhupanovsky volcano (whose composition was estimated from data on the most primitive melt inclusions) had a composition of low-Si (~45 wt % SiO2) picrobasalt (~14 wt % MgO), as is typical of parental melts in Kamchatka and other island arcs, and was different from MORB. This primary melt could be derived by ~8% melting of mantle peridotite of composition close to the MORB source, under pressures of 1.5 ± 0.2 GPa and temperatures 20-30°C lower than the solidus temperature of 'dry' peridotite (1230-1240°C). Melting was induced by the interaction of the hot peridotite with a hydrous component that was brought to the mantle from the subducted slab and was also responsible for the enrichment of the Zhupanovsky magmas in LREE, LILE, B, Cl, Th, U, and Pb. The hydrous component in the magma source of Zhupanovsky volcano was produced by the partial slab melting under water-saturated conditions at temperatures of 760-810°C and pressures of ~3.5 GPa. As the depth of the subducted slab beneath Kamchatkan volcanoes varies from 100 to 125 km, the composition of the hydrous component drastically changes from relatively low-temperature H2O-rich fluid to higher temperature H2O-bearing melt. The geothermal gradient at the surface of the slab within the depth range of 100-125 km beneath Kamchatka was estimated at 4°C/km.

Very low temperatures, their attainment and uses : a survey of the physical principles underlying the attainment of extremely low temperatures and of their technical and scientific applications, as illustrated in a special exhibition held in the Science museum--March-May, 1936 /

"Chart of fixed points and temperature scales": p. [3] of cover.

Analysis of adsorption of gases and vapors on nonporous graphitized thermal carbon black

In this paper we analyzed the adsorption of a large number of gases and vapors on graphitized thermal carbon black. The Henry constant was used to determine the adsorbate-adsorbent interaction energy, which is found to be a modest decreasing function of temperature. Analysis of the complete adsorption isotherm over a wider range of pressure yields information on the monolayer coverage concentration and the adsorbate-adsorbate interaction energy. Among the various equations tested, the Hill-de Boer equation accounting for BET-postulated multilayer formation describes well the adsorption isotherms of all adsorbates. On average, the adsorbate-adsorbate interaction energy in the adsorbed phase is less than that in the bulk phase, suggesting that the distance between adsorbed molecules in the first layer of the adsorbed phase is slightly less than the equilibrium distance between two adsorbate molecules in the bulk phase. This suggests that the first layer is in a compressed state, which is due to the attraction of the adsorbent surface. The monolayer concentration as determined from the fitting of the Hill-de Boer equation with experimental data is slightly larger than the values calculated from the molecular projection area, suggesting that molecules can be oriented such that a larger number of molecules can be accommodated on the carbon black surface. This further supports the shorter distance between adsorbate molecules in the adsorbed phase.