Soodakattilan lentotuhkan uudentyyppisen analysaattorin arviointi

RBDA (Recovery Boiler Dust Analyzer) on soodakattilan savukaasujen hiukkasten määrää mittaava laite. Yksi laitteen mahdollisista sovelluskohteista on soodakattilan nuohouksen optimointi. Tämän työn tarkoituksena oli parantaa RBD-analysaattorin toimintaa ja erityisesti tutkia laitteen toimivuutta soodakattilan nuohouksen optimoinnis-sa. Soodakattilan nuohouksen optimoinnilla voidaan vähentää nuohoukseen kuluneen höyryn määrää ja näin saavuttaa taloudellisia säästöjä. RBD-analysaattorin toimivuutta testattiin toimivan soodakattilan avulla. Tutkimuksen tueksi testeissä käytetyn soodakattilan savukaasujen lämpötilat ja tuhkan tarttumisomi-naisuudet selvitettiin. Laitteen toimivuutta testattiin vertaamalla RBDA:n mittaustulosta standardin mukaiseen savukaasujen hiukkasmittausmenetelmään. Mittajärjestelmän soveltuvuutta soodakattilan nuohouksen optimointiin tutkittiin ajamalla nuohoimia käsin eri seisonta-aikojen jälkeen sekä mittaamalla soodakattilan normaalia nuohousjärjes-tystä. Mittausten perusteella todettiin, että RBDA havaitsee savukaasujen pölypitoisuuden ja sen muutokset luotettavasti. Nuohouksen optimointiin RBDA:n todettiin soveltuvan ny-kyisessä mallissaan vain vedenesilämmittimien osalta. Keittopinnan ja tulistimien nuo-hointen optimointiin ei saatu riittävän luotettavia mittaustuloksia. RBDA:n kehittäminen jatkotutkimuksilla todettiin mahdolliseksi.

Test of a microlysimeter for measurement of soil evaporation

Quantifying soil evaporation is required on studies of soil water balance and applications aiming to improve water use efficiency by crops. The performance of a microlysimeter (ML) to measure soil evaporation under irrigation and non-irrigation was evaluated. The MLs were constructed using PVC tubes, with dimensions of 100 mm inner diameter, 150 mm depth and 2.5 mm wall thickness. Four MLs were uniformly distributed on the soil surface of two weighing lysimeters conducted under bare soil, previously installed at Iapar, in Londrina, PR, Brazil. The lysimeters had 1.4 m width, 1.9 m length and 1.3 m depth and were conducted with and without irrigation. Evaporation measurements by MLs (E ML) were compared with measurements by lysimeters (E L) during four different periods in the year. Differences between E ML and E L were small either for low or high atmospheric demand and also for either irrigated or non-irrigated conditions, which indicates that the ML tested here is suitable for measurement of soil evaporation.

Measurement systems of soil water matric potential and evaluation of soil moisture under different irrigation depths

The development of new methodologies and tools that enable to determine the water content in soil is of fundamental importance to the practice of irrigation. The objective of this study was to evaluate soil matric potential using mercury tensiometer and puncture digital tensiometer, and to compare the gravimetric soil moisture values obtained by tensiometric system with gravimetric soil moisture obtained by neutron attenuation technique. Four experimental plots were maintained with different soil moisture by irrigation. Three repetitions of each type of tensiometer were installed at 0.20 m depth. Based on the soil matric potential and the soil water retention curve, the corresponding gravimetric soil moisture was determined. The data was then compared to those obtained by neutron attenuation technique. The results showed that both tensiometric methods showed no difference under soil matric potential higher than -40 kPa. However, under drier soil, when the water was replaced by irrigation, the soil matric potential of the puncture digital tensiometer was less than those of the mercury tensiometer.

Design of Pulsed Electroacoustic Measurement System for Space Charge Characterisation

Pulsed electroacoustic (PEA) method is a commonly used non-destructive technique for investigating space charges. It has been developed since early 1980s. These days there is continuing interest for better understanding of the influence of space charge on the reliability of solid electrical insulation under high electric field. The PEA method is widely used for space charge profiling for its robust and relatively inexpensive features. The PEA technique relies on a voltage impulse used to temporarily disturb the space charge equilibrium in a dielectric. The acoustic wave is generated by charge movement in the sample and detected by means of a piezoelectric film. The spatial distribution of the space charge is contained within the detected signal. The principle of such a system is already well established, and several kinds of setups have been constructed for different measurement needs. This thesis presents the design of a PEA measurement system as a systems engineering project. The operating principle and some recent developments are summarised. The steps of electrical and mechanical design of the instrument are discussed. A common procedure for measuring space charges is explained and applied to verify the functionality of the system. The measurement system is provided as an additional basic research tool for the Corporate Research Centre of ABB (China) Ltd. It can be used to characterise flat samples with thickness of 0.2–0.5 mm under DC stress. The spatial resolution of the measurement is 20 μm.

Automatisointiin ja monistettavuuteen perustuvan palvelumallin soveltaminen tietojärjestelmätoimituksissa

Ohjelmistotuotannon yleinen ongelma on se, että toimitusprojektien läpivientiajat pitkittyvät. Kilpailun kiristyessä ohjelmistoalalla on alettu kiinnittää erityistä huomiota projektien eri vaiheiden tehostamiseen. Process Vision Oy kehittää energiatietojärjestelmiä Suomen energia-alan yrityksille. Yrityksessä on kehitetty vuonna 2010 palvelumalli, jonka avulla pyritään nopeuttamaan toimitusprojektien eri vaiheita. Valtioneuvosto valmisteli vuonna 2009 tuntimittausasetuksen, joka määritti sääntöjä mittaustiedon hallintaan energia-alalla. Kyseisen asetuksen pohjalta Energiateollisuus julkaisi vuonna 2010 ohjeistuksen, joka selkeyttää asetuksen sisällön vaatimuksia jakeluverkonhaltijoille ja sähkön myyjille. Process Vision Oy on valmistellut ohjeistuksen pohjalta tuntimittauspaketin, joka sisältää ohjeistuksen mukaiset toiminnot GENERIS-järjestelmässä. Tässä diplomityössä määritellään Process Vision Oy:n palvelumallin mukaiset standardikomponentit tuntimittauspaketin toimitusprojekteja varten. Työn tavoitteena on kehittää mahdollisimman pitkälle tuotteistettu tuntimittauspaketin toimitus uusille ja vanhoille asiakkaille. Työn lopussa pohditaan miten hyvin palvelumalli soveltuu tuntimittauspaketin toimitusprojekteihin. Lisäksi työssä kartoitetaan yrityksessä käytössä olevien automatisointityökalujen kehitystarpeita. Työn tuloksena saatiin määriteltyä GENERIS-objektit ja konfiguraatiot, jotka toimitetaan tuntimittauspaketin mukana. Työn ohessa sisällytettiin yrityksen Suomen taseselvitysjärjestelmien asennusohjeeseen tuntimittauspaketin toiminnallisuuksien konfigurointi. Uusien vientimäärittelyjen avulla voidaan tuntimittauspaketin toiminnallisuudet toimittaa jatkossa tehokkaammin kuin aiemmin.

Developing the measurement and management of knowledge: applying the constructive research approach in a knowledge intensive service environment

Intellectual assets have attained continuous attention in the academic field, as they are vital sources of competitive advantage and organizational performance in the contemporary knowledge intensive business environment. Intellectual capital measurement is quite thoroughly addressed in the accounting literature. However, the purpose of the measurement is to support the management of intellectual assets, but the reciprocal relationship between measurement and management has not been comprehensively considered in the literature. The theoretical motivation for this study rose from this paradox, as in order to maximise the effectiveness of knowledge management the two initiatives need to be closely integrated. The research approach of this interventionist case study is constructive. The objective is to develop the case organization’s knowledge management and intellectual capital measurement in a way that they would be closely integrated and the measurement would support the management of intellectual assets. The case analysis provides valuable practical considerations about the integration and related issues as the case company is a knowledge intensive organization in which the know-how of the employees is the central competitive asset and therefore, the management and measurement of knowledge are essential for its future success. The results suggest that the case organization is confronting challenges in managing knowledge. In order to appropriately manage knowledge processes and control the related risks, support from intellectual capital measurement is required. However, challenges in measuring intellectual capital, especially knowledge, could be recognized in the organization. By reflecting the knowledge management situation and the constructed strategy map, a new intellectual measurement system was developed for the case organization. The construction of the system as well as its indicators can be perceived to contribute to the literature, emphasizing of the importance of properly considering the organization’s knowledge situation in developing an intellectual capital measurement system.

Understanding the in vitro dissolution rate of glasses with respect to future clinical applications

Glass is a unique material with a long history. Several glass products are used daily in our everyday life, often unnoticed. Glass can be found not only in obvious applications such as tableware, windows, and light bulbs, but also in tennis rackets, windmill turbine blades, optical devices, and medical implants. The glasses used at present as implants are inorganic silica-based melt-derived compositions mainly for hard-tissue repair as bone graft substitute in dentistry and orthopedics. The degree of glass reactivity desired varies according to implantation situation and it is vital that the ion release from any glasses used in medical applications is controlled. Understanding the in vitro dissolution rate of glasses provides a first approximation of their behavior in vivo. Specific studies concerning dissolution properties of bioactive glasses have been relatively scarce and mostly concentrated to static condition studies. The motivation behind this work was to develop a simple and accurate method for quantifying the in vitro dissolution rate of highly different types of glass compositions with interest for future clinical applications. By combining information from various experimental conditions, a better knowledge of glass dissolution and the suitability of different glasses for different medical applications can be obtained. Thus, two traditional and one novel approach were utilized in this thesis to study glass dissolution. The chemical durability of silicate glasses was tested in water and TRIS-buffered solution at static and dynamic conditions. The traditional in vitro testing with a TRISbuffered solution under static conditions works well with bioactive or with readily dissolving glasses, and it is easy to follow the ion dissolution reactions. However, in the buffered solution no marked differences between the more durable glasses were observed. The hydrolytic resistance of the glasses was studied using the standard procedure ISO 719. The relative scale given by the standard failed to provide any relevant information when bioactive glasses were studied. However, the clear differences in the hydrolytic resistance values imply that the method could be used as a rapid test to get an overall idea of the biodegradability of glasses. The standard method combined with the ion concentration and pH measurements gives a better estimate of the hydrolytic resistance because of the high silicon amount released from a glass. A sensitive on-line analysis method utilizing inductively coupled plasma optical emission spectrometer and a flow-through micro-volume pH electrode was developed to study the initial dissolution of biocompatible glasses. This approach was found suitable for compositions within a large range of chemical durability. With this approach, the initial dissolution of all ions could be measured simultaneously and quantitatively, which gave a good overall idea of the initial dissolution rates for the individual ions and the dissolution mechanism. These types of results with glass dissolution were presented for the first time during the course of writing this thesis. Based on the initial dissolution patterns obtained with the novel approach using TRIS, the experimental glasses could be divided into four distinct categories. The initial dissolution patterns of glasses correlated well with the anticipated bioactivity. Moreover, the normalized surface-specific mass loss rates and the different in vivo models and the actual in vivo data correlated well. The results suggest that this type of approach can be used for prescreening the suitability of novel glass compositions for future clinical applications. Furthermore, the results shed light on the possible bioactivity of glasses. An additional goal in this thesis was to gain insight into the phase changes occurring during various heat treatments of glasses with three selected compositions. Engineering-type T-T-T curves for glasses 1-98 and 13-93 were stablished. The information gained is essential in manufacturing amorphous porous implants or for drawing of continuous fibers of the glasses. Although both glasses can be hot worked to amorphous products at carefully controlled conditions, 1-98 showed one magnitude greater nucleation and crystal growth rate than 13-93. Thus, 13-93 is better suited than 1-98 for working processes which require long residence times at high temperatures. It was also shown that amorphous and partially crystalline porous implants can be sintered from bioactive glass S53P4. Surface crystallization of S53P4, forming Na2O∙CaO∙2SiO2, was observed to start at 650°C. The secondary crystals of Na2Ca4(PO4)2SiO4, reported for the first time in this thesis, were detected at higher temperatures, from 850°C to 1000°C. The crystal phases formed affected the dissolution behavior of the implants in simulated body fluid. This study opens up new possibilities for using S53P4 to manufacture various structures, while tailoring their bioactivity by controlling the proportions of the different phases. The results obtained in this thesis give valuable additional information and tools to the state of the art for designing glasses with respect to future clinical applications. With the knowledge gained we can identify different dissolution patters and use this information to improve the tuning of glass compositions. In addition, the novel online analysis approach provides an excellent opportunity to further enhance our knowledge of glass behavior in simulated body conditions.

Design of Instrument for Knee Joint Kinematics Measurement

This thesis describes the process of design and modeling of instrument for knee joint kinematics measurement that can work for both in-vivo and in-vitro subjects. It is designed to be compatible with imaging machine in a sagittal plane. Due to the invasiveness of the imaging machine, the instrument is designed to be able to function independently. The flexibility of this instrument allows to measure anthropometrically different subject. Among the sixth degree of freedom of a knee, three rotational and one translational degree of freedom can be measured for both type of subject. The translational, proximal-distal, motion is stimulated by external force directly applied along its axis. These angular and linear displacements are measured by magnetic sensors and high precision potentiometers respectively

Pricing anomalies in the Finnish stock market

The aim of this thesis is to examine whether the pricing anomalies exists in the Finnish stock markets by comparing the performance of quantile portfolios that are formed on the basis of either individual valuation ratios, composite value measures or combined value and momentum indicators. All the research papers included in the thesis show evidence of value anomalies in the Finnish stock markets. In the first paper, the sample of stocks over the 1991-2006 period is divided into quintile portfolios based on four individual valuation ratios (i.e., E/P, EBITDA/EV, B/P, and S/P) and three hybrids of them (i.e. composite value measures). The results show the superiority of composite value measures as selection criterion for value stocks, particularly when EBITDA/EV is employed as earnings multiple. The main focus of the second paper is on the impact of the holding period length on performance of value strategies. As an extension to the first paper, two more individual ratios (i.e. CF/P and D/P) are included in the comparative analysis. The sample of stocks over 1993- 2008 period is divided into tercile portfolios based on six individual valuation ratios and three hybrids of them. The use of either dividend yield criterion or one of three composite value measures being examined results in best value portfolio performance according to all performance metrics used. Parallel to the findings of many international studies, our results from performance comparisons indicate that for the sample data employed, the yearly reformation of portfolios is not necessarily optimal in order to maximally gain from the value premium. Instead, the value investor may extend his holding period up to 5 years without any decrease in long-term portfolio performance. The same holds also for the results of the third paper that examines the applicability of data envelopment analysis (DEA) method in discriminating the undervalued stocks from overvalued ones. The fourth paper examines the added value of combining price momentum with various value strategies. Taking account of the price momentum improves the performance of value portfolios in most cases. The performance improvement is greatest for value portfolios that are formed on the basis of the 3-composite value measure which consists of D/P, B/P and EBITDA/EV ratios. The risk-adjusted performance can be enhanced further by following 130/30 long-short strategy in which the long position of value winner stocks is leveraged by 30 percentages while simultaneously selling short glamour loser stocks by the same amount. Average return of the long-short position proved to be more than double stock market average coupled with the volatility decrease. The fifth paper offers a new approach to combine value and momentum indicators into a single portfolio-formation criterion using different variants of DEA models. The results throughout the 1994-2010 sample period shows that the top-tercile portfolios outperform both the market portfolio and the corresponding bottom-tercile portfolios. In addition, the middle-tercile portfolios also outperform the comparable bottom-tercile portfolios when DEA models are used as a basis for stock classification criteria. To my knowledge, such strong performance differences have not been reported in earlier peer-reviewed studies that have employed the comparable quantile approach of dividing stocks into portfolios. Consistently with the previous literature, the division of the full sample period into bullish and bearish periods reveals that the top-quantile DEA portfolios lose far less of their value during the bearish conditions than do the corresponding bottom portfolios. The sixth paper extends the sample period employed in the fourth paper by one year (i.e. 1993- 2009) covering also the first years of the recent financial crisis. It contributes to the fourth paper by examining the impact of the stock market conditions on the main results. Consistently with the fifth paper, value portfolios lose much less of their value during bearish conditions than do stocks on average. The inclusion of a momentum criterion somewhat adds value to an investor during bullish conditions, but this added value turns to negative during bearish conditions. During bear market periods some of the value loser portfolios perform even better than their value winner counterparts. Furthermore, the results show that the recent financial crisis has reduced the added value of using combinations of momentum and value indicators as portfolio formation criteria. However, since the stock markets have historically been bullish more often than bearish, the combination of the value and momentum criteria has paid off to the investor despite the fact that its added value during bearish periods is negative, on an average.

Genetic analysis and cAMP measurement: comparison between lean and obese anovulating mice

PURPOSE: To evaluate genes differentially expressed in ovaries from lean (wild type) and obese (ob/ob) female mice and cyclic AMP production in both groups.METHODS: The expression on messenger RNA levels of 84 genes concerning obesity was analyzed through the PCR array, and cyclic AMP was quantified by the enzyme immunoassay method.RESULTS: The most downregulated genes in the Obesity Group included adenylate cyclase-activating polypeptide type 1, somatostatin, apolipoprotein A4, pancreatic colipase, and interleukin-1 beta. The mean decrease in expression levels of these genes was around 96, 40, 9, 4.2 and 3.6-fold, respectively. On the other hand, the most upregulated genes in the Obesity Group were receptor (calcitonin) activity-modifying protein 3, peroxisome proliferator activated receptor alpha, calcitonin receptor, and corticotropin-releasing hormone receptor 1. The increase means in the expression levels of such genes were 2.3, 2.7, 4.8 and 6.3-fold, respectively. The ovarian cyclic AMP production was significantly higher in ob/ob female mice (2,229±52 fMol) compared to the Control Group (1,814±45 fMol).CONCLUSIONS: Obese and anovulatory female mice have reduced reproductive hormone levels and altered ovogenesis. Several genes have their expression levels altered when leptin is absent, especially adenylate cyclase-activating polypeptide type 1.

Dynaamisen lämmönsiirtomallin kehittäminen

Dynaamisia simulointimalleja tarvitaan, jotta voidaan tarkastella järjestelmän käyttäytymistä ajan funktiona. Simulointimallilla voidaan simuloida järjestelmän lähtö erilaisilla herätteillä. Mallin avulla saadaan myös tarkempi käsitys järjestelmästä ja sen osa-alueista, koska simulointimallista voidaan tarkastella sellaisia asioita, jotka voivat olla oikeasta järjestelmästä vaikeasti mitattavia. Tässä työssä kehitetään LUT Energian hyötysuhdemittapaikan keskikokoista kalorimetriä approksimoiva dynaaminen lämmönsiirtomalli käyttäen Matlab® Simulink -ohjelmistoa. Kehitetyn lämmönsiirtomallin tarkkuutta arvioidaan todellisella järjestelmällä tehdyillä mittauksilla. Työssä käytetään karkeita approksimaatioita, jotka tulee korvata tarkemmilla matemaattisilla malleilla jatkokehitystä varten. Työssä kehitetty dynaaminen lämmönsiirtomalli approksimoi todellisen järjestelmän vastetta lämmitysvaiheessa keskimääräisenvirheen ±0,19 °C tarkkuudella.

Customer profitability measurement in a not-for-profit organization

The objective of this study was to find out the factors that affect customer profitability in the not-for-profit case company. The customer profitability was examined in two different segments of the customer base. The effects that price, cost and the amount of services provided have on the profit margin were studied. The distribution of profitability among the customers and the effect of certain characteristics, such as size of the customer measured in services purchased, on the profitability were analyzed. The theoretical framework was built around customer profitability and the use of customer profitability information in a not-for-profit organization. The present use of customer profitability information and the possibilities of using the results of this research in the case company were presented. Quantitative research methods were used in the empirical part of the study. The results indicate that the two customer segments have differences in their buying behaviors which affect the profitability and thus the measures taken to improve the profitability should be considered with the different characteristics of the customers in mind. Finally the limitations of the study were discussed as possible further research topics.

Design of an amplifier and an instrumentation setup for a harsh environment heat flux measurement application – case axial flux electric machine

Measurement is a tool for researching. Therefore, it is important that the measuring process is carried out correctly, without distorting the signal or the measured event. Researches of thermoelectric phenomena have been focused more on transverse thermoelectric phenomena during recent decades. Transverse Seebeck effect enables to produce thinner and faster heat flux sensor than before. Studies about transverse Seebeck effect have so far focused on materials, so in this Master’s Thesis instrumentation of transverse Seebeck effect based heat flux sensor is studied, This Master’s Thesis examines an equivalent circuit of transverse Seebeck effect heat flux sensors, their connectivity to electronics and choosing and design a right type amplifier. The research is carried out with a case study which is Gradient Heat Flux Sensors and an electrical motor. In this work, a general equivalent circuit was presented for the transverse Seebeck effect-based heat flux sensor. An amplifier was designed for the sensor of the case study, and the solution was produced for the measurement of the local heat flux of the electric motor to improve the electromagnetic compatibility.

Ethological activities, ruminal parameters and weight gain of calves supplemented with different amounts of sodium chloride

The daily weight gain, behavioral activities (grazing, ruminating and water consumption) and the number of rumen protozoa, pH, NH3, and the osmolarity of rumen fluid was evaluated for four groups of six calves HPB/Zebu submitted to daily intake of 15, 30, 60 and 90g of NaCl during 135 days (9th Jan. to 24th May 2008).Throughout the experimental period the calves were in perfect health condition and did not show any signs suggestive of chronic sodium poisoning. There was no significant difference in average daily gain of the calves as the intake of NaCl increased. No significant behavioral changes were observed in the activities of grazing and rumination. However, there was a noticeable change in the frequency of water consumption in the calves that ingested 90g/d of NaCl; they went more often to the trough and drank more water than the group that ingested only 15g sodium chloride/d. The osmolarity of ruminal liquid was higher in the group of calves fed 90g of NaCl/d. The pH, NH3 concentration and number of rumen protozoa was within the normal range.