Physical and chemical kinetics of structural build-up of cement suspensions

Abstract : The structural build-up of fresh cement-based materials has a great impact on their structural performance after casting. Accordingly, the mixture design should be tailored to adapt the kinetics of build-up given the application on hand. The rate of structural build-up of cement-based suspensions at rest is a complex phenomenon affected by both physical and chemical structuration processes. The structuration kinetics are strongly dependent on the mixture’s composition, testing parameters, as well as the shear history. Accurate measurements of build-up rely on the efficiency of the applied pre-shear regime to achieve an initial well-dispersed state as well as the applied stress during the liquid-solid transition. Studying the physical and chemical mechanisms of build-up of cement suspensions at rest can enhance the fundamental understanding of this phenomenon. This can, therefore, allow a better control of the rheological and time-dependent properties of cement-based materials. The research focused on the use of dynamic rheology in investigating the kinetics of structural build-up of fresh cement pastes. The research program was conducted in three different phases. The first phase was devoted to evaluating the dispersing efficiency of various disruptive shear techniques. The investigated shearing profiles included rotational, oscillatory, and combination of both. The initial and final states of suspension’s structure, before and after disruption, were determined by applying a small-amplitude oscillatory shear (SAOS). The difference between the viscoelastic values before and after disruption was used to express the degree of dispersion. An efficient technique to disperse concentrated cement suspensions was developed. The second phase aimed to establish a rheometric approach to dissociate and monitor the individual physical and chemical mechanisms of build-up of cement paste. In this regard, the non-destructive dynamic rheometry was used to investigate the evolutions of both storage modulus and phase angle of inert calcium carbonate and cement suspensions. Two independent build-up indices were proposed. The structural build-up of various cement suspensions made with different cement contents, silica fume replacement percentages, and high-range water reducer dosages was evaluated using the proposed indices. These indices were then compared to the well-known thixotropic index (Athix.). Furthermore, the proposed indices were correlated to the decay in lateral pressure determined for various cement pastes cast in a pressure column. The proposed pre-shearing protocol and build-up indices (phases 1 and 2) were then used to investigate the effect of mixture’s parameters on the kinetics of structural build-up in phase 3. The investigated mixture’s parameters included cement content and fineness, alkali sulfate content, and temperature of cement suspension. Zeta potential, calorimetric, spectrometric measurements were performed to explore the corresponding microstructural changes in cement suspensions, such as inter-particle cohesion, rate of Brownian flocculation, and nucleation rate. A model linking the build-up indices and the microstructural characteristics was developed to predict the build-up behaviour of cement-based suspensions The obtained results showed that oscillatory shear may have a greater effect on dispersing concentrated cement suspension than the rotational shear. Furthermore, the increase in induced shear strain was found to enhance the breakdown of suspension’s structure until a critical point, after which thickening effects dominate. An effective dispersing method is then proposed. This consists of applying a rotational shear around the transitional value between the linear and non-linear variations of the apparent viscosity with shear rate, followed by an oscillatory shear at the crossover shear strain and high angular frequency of 100 rad/s. Investigating the evolutions of viscoelastic properties of inert calcite-based and cement suspensions and allowed establishing two independent build-up indices. The first one (the percolation time) can represent the rest time needed to form the elastic network. On the other hand, the second one (rigidification rate) can describe the increase in stress-bearing capacity of formed network due to cement hydration. In addition, results showed that combining the percolation time and the rigidification rate can provide deeper insight into the structuration process of cement suspensions. Furthermore, these indices were found to be well-correlated to the decay in the lateral pressure of cement suspensions. The variations of proposed build-up indices with mixture’s parameters showed that the percolation time is most likely controlled by the frequency of Brownian collisions, distance between dispersed particles, and intensity of cohesion between cement particles. On the other hand, a higher rigidification rate can be secured by increasing the number of contact points per unit volume of paste, nucleation rate of cement hydrates, and intensity of inter-particle cohesion.

Synthesis, characterization and chemical vapor deposition of transition metal di(tert-butyl)amido compounds

Although the transition metal chemistry of many dialkylamido ligands has been well studied, the chemistry of the bulky di(tert-butyl)amido ligand has been largely overlooked. The di(tert-butyl)amido ligand is well suited for synthesizing transition metal compounds with low coordination numbers; such compounds may exhibit interesting structural, physical, and chemical properties. Di(tert-butyl)amido complexes of transition metals are expected to exhibit high volatilities and low decomposition temperatures, thus making them well suited for the chemical vapor deposition of metals and metal nitrides. Treatment of MnBr₂(THF)₂, FeI₂, CoBr₂(DME), or NiBr₂(DME) with two equivalents of LiN(t-Bu)2 in benzene affords the two-coordinate complex M[N(t-Bu)₂]₂, where M is Mn, Fe, Co, or Ni. Crystallographic studies show that the M-N distances decrease across the series: 1.9365 (Mn), 1.8790 (Fe), 1.845 (Co), 1.798 Å (Ni). The N-M- N angles are very close to linear for Mn and Fe (179.30 and 179.45°, respectively), but bent for Co and Ni (159.2 and 160.90°, respectively). As expected, the d⁵ Mn complex has a magnetic moment of 5.53 μΒ that is very close to the spin only value. The EPR spectrum is nearly axial with a low E/D ratio of 0.014. The d⁶ Fe compound has a room temperature magnetic moment of 5.55 μΒ indicative of a large orbital angular momentum contribution. It does not exhibit a Jahn-Teller distortion despite the expected doubly degenerate ground state. Applied field Mössbauer spectroscopy shows that the effective internal hyperfine field is unusually large, Hint = 105 T. The magnetic moments of Co[N(t-Bu)₂]₂ and Ni[N(t-Bu)₂]₂ are 5.24 and 3.02 μΒ respectively. Both are EPR silent at 4.2 K. Treatment of TiCl₄ with three equivalents of LiN(t-Bu)2 in pentane affords the briding imido compound Ti₂[μ-N(t-Bu)]₂Cl₂[N(t-Bu)₂]₂ via a dealkylation reaction. Rotation around the bis(tert-butyl)amido groups is hindered, with activation parameters of ΔH‡ = 12.8 ± 0.6 kcal mol-1 and ΔS‡ = -8 ± 2 cal K-1 ·mol-1, as evidenced by variable temperature 1H NMR spectroscopy. Treatment of TiCl₄ with two equivalents of HN(t-Bu)₂ affords Ti₂Cl₆[N(t-Bu)₂]₂. This complex shows a close-contact of 2.634(3) Å between Ti and the carbon atom of one of the CH₃ substituents on the tert-butyl groups. Theoretical considerations and detailed structural comparisons suggest this interaction is not agostic in nature, but rather is a consequence of interligand repulsions. Treatment of NiI₂(PPh3)₂ and PdCl₂(PPh₃)₂ with LiN(t-Bu)₂in benzene affords Ni[N(t-Bu)₂](PPh₃)I and Pd₃(μ₂-NBut₂)2(μ₂-PPh₂)Ph(PPh₃) respectively. The compound Ni[N(t-Bu)₂](PPh₃)I has distorted T-shape in geometry, whereas Pd₃(μ₂-NBut₂)₂(μ₂-PPh₂)Ph(PPh₃) contains a triangular palladium core. Manganese nitride films were grown from Mn[N(t-Bu)₂]₂ in the presence of anhydrous ammonia. The growth rate was several nanometers per minute even at the remarkably low temperature of 80⁰C. As grown, the films are carbon- and oxygen-free, and have a columnar morphology. The spacings between the columns become smaller and the films become smoother as the growth temperature is increased. The composition of the films is consistent with a stoichiometry of Mn₅N₂.

Nutritional and chemical characterization of food products enriched with biological produced fruits of Vaccinum myrtillus L

Vaccinum myrtillus L. belongs to Ericaceae family, being commonly known for its sweet small fruits: the blueberries. Widely consumed in fresh, these fruits are also used in jams and marmalades due to their digestive and hypoglycemic properties and also due to the presence of several bioactive compounds [!]. Therefore, it has become a very appealing matrix in the development of functional products that, beyond their nutritional properties, will add a long-term beneficial physiological/health effect [2]. In the present work, three novel blueberry based products developed by RBR Foods Company (Portugal), were characterized in terms of their nutritional and chemical properties: carbohydrates, ash, proteins, fat and energetic value (following official methods of food analysis), fatty acids profile (by CG-FID), soluble sugars (by HPLCRI), organic acids (by HPLC-DAD) and tocopherols (by HPLC-fluorescence). The products result from a mixture of the fruits with rose petals (PI), marigold petals (P2) and apple and goji berries (P3). The blueberry fruits were used as control sample. The nutritional profile of the novel products was very similar to the control sample: the carbohydrates were the most abundant macronutrient, followed by proteins and total fat. Regarding sugars, fructose, glucose and sucrose were identified in all the samples. P 1 and P2 didn't show significant differences in comparison to the control, however, P3 revealed a lower concentration of sugars. In terms of fatty acids composition, all the studied samples presented higher contents in polyunsaturated fatty acids, especially due to the contribution of linoleic and alinolenic acids. The results of tocopherols revealed that the control sample only presented two isoforrns of tocopherols, a- and y-tocopherol, being the same observed in P3. However, P 1 revealed the presence of all the isoforrns of tocopherols, while P2 was lacking otocopherol; which is related with the contribution of rose and marigold petals, respectively. The a-tocopherol isoforrn was the most abundant in all the studied samples. Overall, this work contributed to the nutritional characterization of novel blueberry based products and is a part of a wider project that aims the detailed study of these products, namely their potential to be used as functional foods.

Sequestering of Fe and Pb ions from Wastewater by Canarium schweinfurthii after carbonization and chemical treatment: Isothermal and Kinetic Modeling

In this paper agricultural waste; Canarium schweinfurthii was explored for the sequestering of Fe and Pb ions from wastewater solution after carbonization and chemical treatment at 400oC. Optimum time of 30 and 150 min with percentage removal of 95 and 98% at optimum pH of 2 and 6 was obtained for Fe and Pb ions. Kinetics model followed pseudofirst order as sum of absolute error (EABS) between Qe and Qc greater than that of pseudo second order. Parameters evaluated from isothermal equation (Freundlich and Langmuir) showed that KL and QO for Fe > Pb and R2 for Langmuir> Freundlich. The study reveals the suitability of the adsorbent for sequestering of Fe and Pb ions from industrial wastewater.

In vivo antileishmanial activity and chemical profile of polar extract from Selaginella sellowii

The polar hydroethanolic extract from Selaginella sellowii (SSPHE) has been previously proven active on intracellular amastigotes (in vitro test) and now was tested on hamsters infected with Leishmania (Leishmania) amazonensis (in vivo test). SSPHE suppressed a 100% of the parasite load in the infection site and draining lymph nodes at an intralesional dose of 50 mg/kg/day × 5, which was similar to the results observed in hamsters treated with N-methylglucamine antimonate (Sb) (28 mg/Kg/day × 5). When orally administered, SSPHE (50 mg/kg/day × 20) suppressed 99.2% of the parasite load in infected footpads, while Sb suppressed 98.5%. SSPHE also enhanced the release of nitric oxide through the intralesional route in comparison to Sb. The chemical fingerprint of SSPHE by high-performance liquid chromatography with diode-array detection and tandem mass spectrometry showed the presence of biflavonoids and high molecular weight phenylpropanoid glycosides. These compounds may have a synergistic action in vivo. Histopathological study revealed that the intralesional treatment with SSPHE induced an intense inflammatory infiltrate, composed mainly of mononuclear cells. The present findings reinforce the potential of this natural product as a source of future drug candidates for American cutaneous leishmaniasis.

A simple approach to integrate the ecotoxicological and chemical data for the establishment of environmental risk levels

O presente trabalho utilizou métodos multivariados e matemáticos para integrar dados químicos e ecotoxicológicos obtidos para o Sistema Estuarino de Santos e para a região próxima à zona de lançamento do emissário submarino de Santos, com a finalidade de estabelecer com maior exatidão os riscos ambientais, e assim identificar áreas prioritárias e orientar programas de controle e políticas públicas. Para ambos os conjuntos de dados, as violações de valores numéricos de qualidade de sedimento tenderam a estar associadas com a ocorrência de toxicidade. Para o estuário, essa tendência foi corroborada pelas correlações entre a toxicidade e as concentrações de HPAs e Cu, enquanto para a região do emissário, pela correlação entre toxicidade e conteúdo de mercúrio no sedimento. Valores normalizados em relação às medias foram calculados para cada amostra, permitindo classificá-las de acordo com a toxicidade e a contaminação. As análises de agrupamento confirmaram os resultados das classificações. Para os dados de sistema estuarino, houve a separação das amostras em três categorias: as estações SSV-2, SSV-3 e SSV-4 encontram-se sob maior risco, seguidas da estação SSV-6. As estações SSV-1 e SSV-5 demonstraram melhores condições. Já em relação ao emissário, as amostras 1 e 2 apresentaram melhores condições, enquanto a estação 5 pareceu apresentar um maior risco, seguida das estações 3 e 4 que tiveram apenas alguns indícios de alteração.

Changes in physical and chemical parameters of the traditional portuguese product água-mel during the production process

Changes in physical and chemical parameters (viscosity, total soluble solids and Hunter color parameters L*, a*, b*, chroma and hue angle) of água-mel were investigated throughout processing. Kinetic parameters for color change of heatprocessed água-mel were monitored. A zero-order kinetic model was applied to changes in L* and b*, while a* and C* were described using a first-order kinetic model. The heating process changed all three color parameters (L*, a*, b*), causing a shift toward the darker colors. Parameters L* decreased, while a*, b*, C* and hue angle (°h) increased during heating. Regarding changes in total soluble solids and in apparent viscosity, both fitted first-order kinetics. A direct relationship was found between the changes in these two parameters. The increase in both total soluble solids and viscosity affected a*, b* and C*. In addition, a flow diagram for the Portuguese água-mel production process has been established.

Physical and chemical properties of starch and flour from different common bean (Phaseolus vulgaris L.) cultivar.

The physical, chemical and pasting properties of the flour and isolated starches from six different bean cultivars (Phaseolus vulgaris L.) were investigated in order to obtain information for application in new products. The protein and total starch contents of the bean flours ranged from 17.72 to 20.27% and from 39.68 to 43.78%, respectively. The bean starches had low amounts of proteins, lipids and ash and showed an amylose content ranging between 45.32 and 51.11% and absolute density values between 1.55 and 1.78 g.cm?3. The bean starch granules were round to oval with a smooth surface. Results viscoamylographic profiles of the starches and flours showed the possibility of selecting cultivars for specific applications according to these characteristics.

Biological and chemical strategies for the recovery of precious and rare metals as nanoparticles

Tese de Doutoramento, Ciências do Mar da Terra e do Ambiente, Ramo: Ciências e Tecnologias do Ambiente, Especialidade em Biotecnologia, Faculdade de Ciências e Tecnologia, Universidade do Algarve, 2016

Fast Detection and Chemical Characterization of Gunshot Residues by CMV-GC-MS and LIBS

Gunshot residue (GSR) is the term used to describe the particles originating from different parts of the firearm and ammunition during the discharge. A fast and practical field tool to detect the presence of GSR can assist law enforcement in the accurate identification of subjects. A novel field sampling device is presented for the first time for the fast detection and quantitation of volatile organic compounds (VOCs). The capillary microextraction of volatiles (CMV) is a headspace sampling technique that provides fast results (< 2 min. sampling time) and is reported as a versatile and high-efficiency sampling tool. The CMV device can be coupled to a Gas Chromatography-Mass Spectrometry (GC-MS) instrument by installation of a thermal separation probe in the injection port of the GC. An analytical method using the CMV device was developed for the detection of 17 compounds commonly found in polluted environments. The acceptability of the CMV as a field sampling method for the detection of VOCs is demonstrated by following the criteria established by the Environmental Protection Agency (EPA) compendium method TO-17. The CMV device was used, for the first time, for the detection of VOCs on swabs from the hands of shooters, and non-shooters and spent cartridges from different types of ammunition (i.e., pistol, rifle, and shotgun). The proposed method consists in the headspace extraction of VOCs in smokeless powders present in the propellant of ammunition. The sensitivity of this method was demonstrated with method detection limits (MDLs) 4-26 ng for diphenylamine (DPA), nitroglycerine (NG), 2,4-dinitrotoluene (2,4-DNT), and ethyl centralite (EC). In addition, a fast method was developed for the detection of the inorganic components (i.e., Ba, Pb, and Sb) characteristic of GSR presence by Laser Induced Breakdown Spectroscopy (LIBS). Advantages of LIBS include fast analysis (~ 12 seconds per sample) and good sensitivity, with expected MDLs in the range of 0.1-20 ng for target elements. Statistical analysis of the results using both techniques was performed to determine any correlation between the variables analyzed. This work demonstrates that the information collected from the analysis of organic components has the potential to improve the detection of GSR.