The design of robust protocols for distributed real-time systems

Modern distributed control systems comprise of a set of processors which are interconnected using a suitable communication network. For use in real-time control environments, such systems must be deterministic and generate specified responses within critical timing constraints. Also, they should be sufficiently robust to survive predictable events such as communication or processor faults. This thesis considers the problem of coordinating and synchronizing a distributed real-time control system under normal and abnormal conditions. Distributed control systems need to periodically coordinate the actions of several autonomous sites. Often the type of coordination required is the all or nothing property of an atomic action. Atomic commit protocols have been used to achieve this atomicity in distributed database systems which are not subject to deadlines. This thesis addresses the problem of applying time constraints to atomic commit protocols so that decisions can be made within a deadline. A modified protocol is proposed which is suitable for real-time applications. The thesis also addresses the problem of ensuring that atomicity is provided even if processor or communication failures occur. Previous work has considered the design of atomic commit protocols for use in non time critical distributed database systems. However, in a distributed real-time control system a fault must not allow stringent timing constraints to be violated. This thesis proposes commit protocols using synchronous communications which can be made resilient to a single processor or communication failure and still satisfy deadlines. Previous formal models used to design commit protocols have had adequate state coverability but have omitted timing properties. They also assumed that sites communicated asynchronously and omitted the communications from the model. Timed Petri nets are used in this thesis to specify and design the proposed protocols which are analysed for consistency and timeliness. Also the communication system is mcxielled within the Petri net specifications so that communication failures can be included in the analysis. Analysis of the Timed Petri net and the associated reachability tree is used to show the proposed protocols always terminate consistently and satisfy timing constraints. Finally the applications of this work are described. Two different types of applications are considered, real-time databases and real-time control systems. It is shown that it may be advantageous to use synchronous communications in distributed database systems, especially if predictable response times are required. Emphasis is given to the application of the developed commit protocols to real-time control systems. Using the same analysis techniques as those used for the design of the protocols it can be shown that the overall system performs as expected both functionally and temporally.

The development of hard real-time systems using a formal approach

Hard real-time systems are a class of computer control systems that must react to demands of their environment by providing `correct' and timely responses. Since these systems are increasingly being used in systems with safety implications, it is crucial that they are designed and developed to operate in a correct manner. This thesis is concerned with developing formal techniques that allow the specification, verification and design of hard real-time systems. Formal techniques for hard real-time systems must be capable of capturing the system's functional and performance requirements, and previous work has proposed a number of techniques which range from the mathematically intensive to those with some mathematical content. This thesis develops formal techniques that contain both an informal and a formal component because it is considered that the informality provides ease of understanding and the formality allows precise specification and verification. Specifically, the combination of Petri nets and temporal logic is considered for the specification and verification of hard real-time systems. Approaches that combine Petri nets and temporal logic by allowing a consistent translation between each formalism are examined. Previously, such techniques have been applied to the formal analysis of concurrent systems. This thesis adapts these techniques for use in the modelling, design and formal analysis of hard real-time systems. The techniques are applied to the problem of specifying a controller for a high-speed manufacturing system. It is shown that they can be used to prove liveness and safety properties, including qualitative aspects of system performance. The problem of verifying quantitative real-time properties is addressed by developing a further technique which combines the formalisms of timed Petri nets and real-time temporal logic. A unifying feature of these techniques is the common temporal description of the Petri net. A common problem with Petri net based techniques is the complexity problems associated with generating the reachability graph. This thesis addresses this problem by using concurrency sets to generate a partial reachability graph pertaining to a particular state. These sets also allows each state to be checked for the presence of inconsistencies and hazards. The problem of designing a controller for the high-speed manufacturing system is also considered. The approach adopted mvolves the use of a model-based controller: This type of controller uses the Petri net models developed, thus preservIng the properties already proven of the controller. It. also contains a model of the physical system which is synchronised to the real application to provide timely responses. The various way of forming the synchronization between these processes is considered and the resulting nets are analysed using concurrency sets.

Computer control of machines utilising independent drive mechanisms

The thesis describes an investigation into methods for the specification, design and implementation of computer control systems for flexible manufacturing machines comprising multiple, independent, electromechanically-driven mechanisms. An analysis is made of the elements of conventional mechanically-coupled machines in order that the operational functions of these elements may be identified. This analysis is used to define the scope of requirements necessary to specify the format, function and operation of a flexible, independently driven mechanism machine. A discussion of how this type of machine can accommodate modern manufacturing needs of high-speed and flexibility is presented. A sequential method of capturing requirements for such machines is detailed based on a hierarchical partitioning of machine requirements from product to independent drive mechanism. A classification of mechanisms using notations, including Data flow diagrams and Petri-nets, is described which supports capture and allows validation of requirements. A generic design for a modular, IDM machine controller is derived based upon hierarchy of control identified in these machines. A two mechanism experimental machine is detailed which is used to demonstrate the application of the specification, design and implementation techniques. A computer controller prototype and a fully flexible implementation for the IDM machine, based on Petri-net models described using the concurrent programming language Occam, is detailed. The ability of this modular computer controller to support flexible, safe and fault-tolerant operation of the two intermittent motion, discrete-synchronisation independent drive mechanisms is presented. The application of the machine development methodology to industrial projects is established.

Nations and organizations:a comparative study of English and Indian work-related attitudes and values in matched manufacturing firms

This thesis reports a cross-national study carried out in England and India in an attempt to clarify the association of certain cultural and non-cultural characteristics with people's work-related attitudes and values, and with the structure of their work organizations. Three perspectives are considered to be relevant to the objectives of the study. The contingency perspective suggests that a 'fit' between an organization's context and its structural arrangements will be fundamentally necessary for achieving success and survival. The political economy perspective argues for the determining role of the social and economic structures within which the organization operates. The culturalist perspective looks to cultural attitudes and values of organizational members for an explanation for their organization's structure. The empirical investigation was carried out in three stages in each of the two countries involved by means of surveys of cultural attitudes, work-related attitudes and organizational structures and systems. The cultural surveys suggested that Indian and English people were different from one another with regard to fear of, and respect and obedience to, their seniors, ability to cope with ambiguity, honesty, independence, expression of emotions, fatalism, reserve, and care for others; they were similar with regard to tolerance, friendliness, attitude to change, attitude to law, self-control and self-confidence, and attitude to social differentiation. The second stage of the study, involving the employees of fourteen organizations, found that the English ones perceived themselves to have more power at work, expressed more tolerance for ambiguity, and had different expectations from their job than did the Indian equivalents. The two samples were similar with respect to commitment to their company and trust in their colleagues. The findings also suggested that employees' occupations, education and age had some influences on their work-related attitudes. The final stage of the research was a study of structures, control systems, and reward and punishment policies of the same fourteen organizations which were matched almost completely on their contextual factors across the two countries. English and Indian organizations were found to be similar in terms of centralization, specialization, chief executive's span of control, height and management control strategies. English organizations, however, were far more formalized, spent more time on consultation and their managers delegated authority lower down the hierarchy than Indian organizations. The major finding of the study was the multiple association that cultural, national and contingency factors had with the structural characteristics of the organizations and with the work-related attitudes of their members. On the basis of this finding, a multi-perspective model for understanding organizational structures and systems is proposed in which the contributions made by contingency, political economy and cultural perspectives are recognized and incorporated.

The dynamics and control of a remotely piloted plan-symmetric helicopter

Prior to the development of a production standard control system for ML Aviation's plan-symmetric remotely piloted helicopter system, SPRITE, optimum solutions to technical requirements had yet to be found for some aspects of the work. This thesis describes an industrial project where solutions to real problems have been provided within strict timescale constraints. Use has been made of published material wherever appropriate, new solutions have been contributed where none existed previously. A lack of clearly defined user requirements from potential Remotely Piloted Air Vehicle (RPAV) system users is identified, A simulation package is defined to enable the RPAV designer to progress with air vehicle and control system design, development and evaluation studies and to assist the user to investigate his applications. The theoretical basis of this simulation package is developed including Co-axial Contra-rotating Twin Rotor (CCTR), six degrees of freedom motion, fuselage aerodynamics and sensor and control system models. A compatible system of equations is derived for modelling a miniature plan-symmetric helicopter. Rigorous searches revealed a lack of CCTR models, based on closed form expressions to obviate integration along the rotor blade, for stabilisation and navigation studies through simulation. An economic CCTR simulation model is developed and validated by comparison with published work and practical tests. Confusion in published work between attitude and Euler angles is clarified. The implementation of package is discussed. dynamic adjustment of assessment. the theory into a high integrity software Use is made of a novel technique basing the integration time step size on error Simulation output for control system stability verification, cross coupling of motion between control channels and air vehicle response to demands and horizontal wind gusts studies are presented. Contra-Rotating Twin Rotor Flight Control System Remotely Piloted Plan-Symmetric Helicopter Simulation Six Degrees of Freedom Motion ( i i)

International selling and sales management:sales force research beyond geographic boundaries

An introduction is presented for this issue which includes the articles "Internationalizing Sales Research: Current Status, Opportunities and Challenges" by Nikolaos G. Panagopoulos and colleagues, "Cultural Intelligence in Cross-Cultural Selling: Propositions and Directions for Future Research" by John D. Hansen and colleagues, and "A New Conceptual Framework of Sales Force Control Systems" by Ren Y. Darmon and Xavier C. Martin

A contingency theory perspective on the risk management control system within Birmingham City Council

In recent years the topic of risk management has moved up the agenda of both government and industry, and private sector initiatives to improve risk and internal control systems have been mirrored by similar promptings for change in the public sector. Both regulators and practitioners now view risk management as an integral part of the process of corporate governance, and an aid to the achievement of strategic objectives. The paper uses case study material on the risk management control system at Birmingham City Council to extend existing theory by developing a contingency theory for the public sector. The case demonstrates that whilst the structure of the control system fits a generic model, the operational details indicate that controls are contingent upon three core variables—central government policies, information and communication technology and organisational size. All three contingent variables are suitable for testing the theory across the broader public sector arena.

A multihop peer-communication protocol with fairness guarantee for IEEE 802.16-based vehicular networks

Wireless-communication technology can be used to improve road safety and to provide Internet access inside vehicles. This paper proposes a cross-layer protocol called coordinated external peer communication (CEPEC) for Internet-access services and peer communications for vehicular networks. We assume that IEEE 802.16 base stations (BS) are installed along highways and that the same air interface is equipped in vehicles. Certain vehicles locating outside of the limited coverage of their nearest BSs can still get access to the Internet via a multihop route to their BSs. For Internet-access services, the objective of CEPEC is to increase the end-to-end throughput while providing a fairness guarantee in bandwidth usage among road segments. To achieve this goal, the road is logically partitioned into segments of equal length. A relaying head is selected in each segment that performs both local-packet collecting and aggregated packets relaying. The simulation results have shown that the proposed CEPEC protocol provides higher throughput with guaranteed fairness in multihop data delivery in vehicular networks when compared with the purely IEEE 802.16-based protocol.

Modeling link adaptation algorithm for IEEE 802.11 wireless LAN networks

Link adaptation is a critical component of IEEE 802.11 systems. In this paper, we analytically model a retransmission based Auto Rate Fallback (ARF) link adaptation algorithm. Both packet collisions and packet corruptions are modeled with the algorithm. The models can provide insights into the dynamics of the link adaptation algorithms and configuration of algorithms parameters. It is also observed that when the competing number of stations is high, packet collisions can largely affected the performance of ARF and make ARF operate with the lowest date rate, even when no packet corruption occur. This is in contrast to the existing assumption that packet collision will not affect the correct operation of ARF and can be ignored in the evaluation of ARF. The work presented in this paper can provide guidelines on configuring the link adaptation algorithms and designing new link adaptation algorithms for future high speed 802.11 systems. © 2006 IEEE.

Logical Models of Composite Dynamic Objects Control

The questions of designing multicriteria control systems on the basis of logic models of composite dynamic objects are considered.

The Complex Unified Evolutionary Approach to the Creation of the Multilevel Distributed Control System of a Gas-transport Company

The objects of a large-scale gas-transport company (GTC) suggest a complex unified evolutionary approach, which covers basic building concepts, up-to-date technologies, models, methods and means that are used in the phases of design, adoption, maintenance and development of the multilevel automated distributed control systems (ADCS).. As a single methodological basis of the suggested approach three basic Concepts, which contain the basic methodological principles and conceptual provisions on the creation of distributed control systems, were worked out: systems of the lower level (ACS of the technological processes based on up-to-date SCADA), of the middle level (ACS of the operative-dispatch production control based on MES-systems) and of the high level (business process control on the basis of complex automated systems ERP).

A mixture density network approach to modelling and exploiting uncertainty in nonlinear control problems

In nonlinear and stochastic control problems, learning an efficient feed-forward controller is not amenable to conventional neurocontrol methods. For these approaches, estimating and then incorporating uncertainty in the controller and feed-forward models can produce more robust control results. Here, we introduce a novel inversion-based neurocontroller for solving control problems involving uncertain nonlinear systems which could also compensate for multi-valued systems. The approach uses recent developments in neural networks, especially in the context of modelling statistical distributions, which are applied to forward and inverse plant models. Provided that certain conditions are met, an estimate of the intrinsic uncertainty for the outputs of neural networks can be obtained using the statistical properties of networks. More generally, multicomponent distributions can be modelled by the mixture density network. Based on importance sampling from these distributions a novel robust inverse control approach is obtained. This importance sampling provides a structured and principled approach to constrain the complexity of the search space for the ideal control law. The developed methodology circumvents the dynamic programming problem by using the predicted neural network uncertainty to localise the possible control solutions to consider. A nonlinear multi-variable system with different delays between the input-output pairs is used to demonstrate the successful application of the developed control algorithm. The proposed method is suitable for redundant control systems and allows us to model strongly non-Gaussian distributions of control signal as well as processes with hysteresis. © 2004 Elsevier Ltd. All rights reserved.

Special issue on intelligent wireless sensor networks and applications

Editorial

High-Order Control Variations and Small-Time Local Controllability

The importance of “control variations” for obtaining local approximations of the reachable set of nonlinear control systems is well known. Heuristically, if one can construct control variations in all possible directions, then the considered control system is small-time locally controllable (STLC). Two concepts of control variations of higher order are introduced for the case of smooth control systems. The relation between these variations and the small-time local controllability is studied and a new sufficient STLC condition is proved.

Optimization of adaptive traffic signal control with transit signal priority at isolated intersections using parallel genetic algorithms

Optimization of adaptive traffic signal timing is one of the most complex problems in traffic control systems. This dissertation presents a new method that applies the parallel genetic algorithm (PGA) to optimize adaptive traffic signal control in the presence of transit signal priority (TSP). The method can optimize the phase plan, cycle length, and green splits at isolated intersections with consideration for the performance of both the transit and the general vehicles. Unlike the simple genetic algorithm (GA), PGA can provide better and faster solutions needed for real-time optimization of adaptive traffic signal control. ^ An important component in the proposed method involves the development of a microscopic delay estimation model that was designed specifically to optimize adaptive traffic signal with TSP. Macroscopic delay models such as the Highway Capacity Manual (HCM) delay model are unable to accurately consider the effect of phase combination and phase sequence in delay calculations. In addition, because the number of phases and the phase sequence of adaptive traffic signal may vary from cycle to cycle, the phase splits cannot be optimized when the phase sequence is also a decision variable. A "flex-phase" concept was introduced in the proposed microscopic delay estimation model to overcome these limitations. ^ The performance of PGA was first evaluated against the simple GA. The results show that PGA achieved both faster convergence and lower delay for both under- or over-saturated traffic conditions. A VISSIM simulation testbed was then developed to evaluate the performance of the proposed PGA-based adaptive traffic signal control with TSP. The simulation results show that the PGA-based optimizer for adaptive TSP outperformed the fully actuated NEMA control in all test cases. The results also show that the PGA-based optimizer was able to produce TSP timing plans that benefit the transit vehicles while minimizing the impact of TSP on the general vehicles. The VISSIM testbed developed in this research provides a powerful tool to design and evaluate different TSP strategies under both actuated and adaptive signal control. ^