Removal of organic contaminants from wastewater using the electrodialytic process

Pharmaceuticals and personal care products (PPCPs) are widely used on a daily basis. After their usage they reach the wastewater treatment plants (WWTPs). These compounds have different physico-chemical characteristics, which makes them difficult to completely remove in the WWTPs, througth conventional treatments. Currently, there is no legislation regarding PPCPs thresholds in effluent discharge. But, even at vestigial concentrations, these compounds enclose environmental risks due to, e.g., endocrine disruption potential. There is a need of alternative techniques for their removal in WWTPs. The main goal of this work was to assess the use of electrodialytic (ED) process to remove PPCPs from the effluent to be discharged. A two-compartment ED cell was used testing (i) the effluent position in the cell (anode and cathode compartment); (ii) the use of anion (AEM) and cation exchange membrane (CEM); (iii) the treatment period (6, 12 and 24 hours); (iv) effluent recirculation and current steps; (v) the feasibility of sequential treatments. Phosphorus (P) removal from effluent and energetic costs associated to the process were also evaluated. Five PPCPs were studied – caffeine (CAF), bisphenol A (BPA), 17 β-estradiol (E2), ethinyl estradiol (EE2) and oxybenzone (MBPh). The ED process showed to be effective in the removal when effluent is in the anode compartment. Oxidation is suggested to be the main removal process, which was between 88 and 96%, for all the compounds, in 6 hours. Nevertheless, the presence of intermediates and/or by-products was also observed in some cases. Effluent recirculation should have a retention time in the ED cell big enough to promote removal whereas the current steps (effluent in anode compartment) slightly increased removal efficiencies (higher than 80% for all PPCPs). The sequential set of ED treatment (effluent in anode compartment) showed to be effective during both periods with a removal percentage between 80 and 95% and 73 to 88% in the case of AEM and CEM, respectively. Again, the main removal process is strongly suggested to be oxidation in the anode compartment. However, there was an increase of BOD5 and COD, which might be explained by effluent spiking, these parameters limiting the effluent discharge. From these treatments, the use of AEM, enhanced the P removal from effluent to minimize risk of eutrophication. Energetic costs of the best set-up (6 hours) are approximately 0,8€/m3 of wastewater, a value considered low, attending to the prices of other treatment processes.

Validation of plant dynamic model by online and laboratory measurements – a tool to predict online COD loads out of production of mechanical printing papers

COD discharges out of processes have increased in line with elevating brightness demands for mechanical pulp and papers. The share of lignin-like substances in COD discharges is on average 75%. In this thesis, a plant dynamic model was created and validated as a means to predict COD loading and discharges out of a mill. The assays were carried out in one paper mill integrate producing mechanical printing papers. The objective in the modeling of plant dynamics was to predict day averages of COD load and discharges out of mills. This means that online data, like 1) the level of large storage towers of pulp and white water 2) pulp dosages, 3) production rates and 4) internal white water flows and discharges were used to create transients into the balances of solids and white water, referred to as “plant dynamics”. A conversion coefficient was verified between TOC and COD. The conversion coefficient was used for predicting the flows from TOC to COD to the waste water treatment plant. The COD load was modeled with similar uncertainty as in reference TOC sampling. The water balance of waste water treatment was validated by the reference concentration of COD. The difference of COD predictions against references was within the same deviation of TOC-predictions. The modeled yield losses and retention values of TOC in pulping and bleaching processes and the modeled fixing of colloidal TOC to solids between the pulping plant and the aeration basin in the waste water treatment plant were similar to references presented in literature. The valid water balances of the waste water treatment plant and the reduction model of lignin-like substances produced a valid prediction of COD discharges out of the mill. A 30% increase in the release of lignin-like substances in the form of production problems was observed in pulping and bleaching processes. The same increase was observed in COD discharges out of waste water treatment. In the prediction of annual COD discharge, it was noticed that the reduction of lignin has a wide deviation from year to year and from one mill to another. This made it difficult to compare the parameters of COD discharges validated in plant dynamic simulation with another mill producing mechanical printing papers. However, a trend of moving from unbleached towards high-brightness TMP in COD discharges was valid.

Devenir environnemental des antidépresseurs dans les rejets urbains par chromatographie liquide à haute performance couplée à la spectrométrie de masse en tandem

Les troubles reliés à la dépression, l’épuisement professionnel et l’anxiété sont de plus en plus répandus dans notre société moderne. La consommation croissante d’antidépresseurs dans les différents pays du monde est responsable de la récente détection de résidus à l’état de traces dans les rejets urbains municipaux. Ainsi, ces substances dites « émergentes » qui possèdent une activité pharmacologique destinée à la régulation de certains neurotransmetteurs dans le cerveau suscitent maintenant de nombreuses inquiétudes de la part de la communauté scientifique. L’objectif principal de ce projet de doctorat a été de mieux comprendre le devenir de plusieurs classes d’antidépresseurs présents dans diverses matrices environnementales (i.e. eaux de surfaces, eaux usées, boues de traitement, tissus biologiques) en développant de nouvelles méthodes analytiques fiables capables de les détecter, quantifier et confirmer par chromatographie liquide à haute performance couplée à la spectrométrie de masse en tandem (LC-QqQMS, LC-QqToFMS). Une première étude complétée à la station d’épuration de la ville de Montréal a permis de confirmer la présence de six antidépresseurs et quatre métabolites N-desmethyl dans les affluents (2 - 330 ng L-1). Pour ce traitement primaire (physico-chimique), de faibles taux d’enlèvement (≤ 15%) ont été obtenus. Des concentrations d’antidépresseurs atteignant près de 100 ng L-1 ont également été détectées dans le fleuve St-Laurent à 0.5 km du point de rejet de la station d’épuration. Une seconde étude menée à la même station a permis l’extraction sélective d’antidépresseurs dans trois tissus (i.e. foie, cerveau et filet) de truites mouchetées juvéniles exposées à différentes concentrations d’effluent dilué traité et non-traité à l’ozone. Un certain potentiel de bioaccumulation dans les tissus (0.08-10 ng g-1) a été observé pour les spécimens exposés à l’effluent non-traité (20% v/v) avec distribution majoritaire dans le foie et le cerveau. Une intéressante corrélation a été établie entre les concentrations de trois antidépresseurs dans le cerveau et l’activité d’un biomarqueur d’exposition (i.e. pompe N/K ATPase impliquée dans la régulation de la sérotonine) mesurée à partir de synaptosomes de truites exposées aux effluents. Une investigation de l’efficacité de plusieurs stations d’épuration canadiennes opérant différents types de traitements a permis de constater que les traitements secondaires (biologiques) étaient plus performants que ceux primaires (physico-chimiques) pour enlever les antidépresseurs (taux moyen d’enlèvement : 30%). Les teneurs les plus élevées dans les boues traitées (biosolides) ont été obtenues avec le citalopram (1033 ng g-1), la venlafaxine (833 ng g-1) et l’amitriptyline (78 ng g-1). Des coefficients de sorption expérimentaux (Kd) calculés pour chacun des antidépresseurs ont permis d’estimer une grande sorption des composés sertraline, desméthylsertraline, paroxetine et fluoxetine sur les solides (log Kd > 4). Finalement, un excellent taux d’enlèvement moyen de 88% a été obtenu après ozonation (5 mg L-1) d’un effluent primaire. Toutefois, la caractérisation de nouveaux sous-produits N-oxyde (venlafaxine, desmethylvenlafaxine) par spectrométrie de masse à haute résolution (LC-QqToFMS) dans l’effluent traité à l’ozone a mis en lumière la possibilité de formation de multiples composés polaires de toxicité inconnue.

Développement d’une méthode d’extraction des contaminants émergents dans les solides particulaires par LDTD-APCI-MS/MS

Douze contaminants émergents (composés pharmaceutiques, pesticides et hormones) ont été quantifiés et extraits de l'eau de rivières et d’échantillons d'eaux usées municipales. La séparation des solides en suspension est effectuée par filtration des échantillons d'eau. L'effet de filtration sur les concentrations de contaminants dissous a été évaluée afin de minimiser les pertes de composés cibles. Les échantillons ont été lyophilisés et ont été extraits en deux cycles par ultrasons combinés avec une étape de nettoyage sur cartouche d’extraction de type C18. La quantification a été réalisée en utilisant la spectrométrie de masse. Les recouvrements de la méthode pour tous les composés ont varié de 68 à 112% dans toutes les matrices étudiées, sauf pour le sulfaméthoxazole et le diclofénac où des recouvrements plus modestes ont été obtenus (38 à 85%). Les limites de détection pour les 12 analytes dans les sédiments et particules en suspension (SPM) de la rivière variaient de 0,7 à 9,4 ng g-1 et de 21 à 92 ng g-1, pour les échantillons SPM de station d'épuration. Tous les contaminants émergents cibles ont été détectés à des concentrations variant de 3 à 5440 ng g-1 dans les matrices étudiées, les concentrations les plus élevées ont été observées dans les échantillons SPM de stations d'épuration. Une partie importante de certains de ces contaminants est clairement associée aux sédiments de rivière ou aux particules en suspension. L’optimisation des processus de traitement de l'eau et le devenir environnemental doit absolument tenir compte de la fraction de contaminants qui liée à des particules si on espère avoir un bilan de masse raisonnable.

Studies on Magnetic Iron Oxide Loaded Activated Carbon

The current water treatment technology is oriented towards the removal of contaminants, mostly organic compounds, by activated carbon. Activated carbons are classified as Granular Activated Carbons (GAC) and Powdered Activated Carbons (PAC) on the basis of the particle size of the carbon granules. Powdered carbons are generally less expensive than granular carbon, operating costs with powdered carbon could be lower. Though powdered activated carbon has many advantages over granular carbon, its application in large-scale separation process is limited by difficulty in recovery and regeneration. Deposition of magnetic iron oxide on carbon particles provides a convenient way of recovering the spent carbon from process water. The study deals with the preparation and physico-chemical characterization of magnetic iron oxide loaded activated carbons. The evaluation of absorption properties of magnetic iron oxide loaded activated carbon composites. The target molecules studied were phenol, p-nitro phenol and methylene blue. The feasibility of magnetic separation of iron oxide loaded activated carbons were studied and described in this thesis.

Optical and Thermal Characterization of Dye Intercalated Montmorillonites and Rare Earth Doped Materials

Nondestructive photothermal methods as well as optical absorption and fluorescence spectroscopy are utilized to characterise three different materials, both thermally and optically. The possibility of using montmorillonite clay minerals, after textile waste-water treatment, is investigated for further applications. The laser induced luminescence studies and thermal characterisation of certain rare earth titanates prepared by self propagating high temperature synthesis method are also presented. Moreover, effort is made to characterise rare earth doped sol gel silica glasses with the help of these nondestructive techniques.

Multivariate Statistical Process Control and Case-Based Reasoning for situation assessment of Sequencing Batch Reactors

ABSRACT This thesis focuses on the monitoring, fault detection and diagnosis of Wastewater Treatment Plants (WWTP), which are important fields of research for a wide range of engineering disciplines. The main objective is to evaluate and apply a novel artificial intelligent methodology based on situation assessment for monitoring and diagnosis of Sequencing Batch Reactor (SBR) operation. To this end, Multivariate Statistical Process Control (MSPC) in combination with Case-Based Reasoning (CBR) methodology was developed, which was evaluated on three different SBR (pilot and lab-scales) plants and validated on BSM1 plant layout.

Adsorbents a partir de fangs biològics excedents de depuradora mitjançant l'aplicació de microones: estudi d'obtenció, caracterització i aplicació en fase líquida

El fang biològic es produeix en les plantes de tractament d'aigües residuals urbanes i industrials. El tractament i la gestió dels fangs és un dels problemes més importants en el camp del tractament de les aigües residuals. Aquesta situació es preveu que es veurà agreujada en el futur, per un increment del volum de fang produït associat a l'exigència de nivells més alts de depuració i per l'augment dels nombre d'estacions depuradores en funcionament. D'altre banda, les limitacions que presenten les opcions tradicionals de gestió dels fangs, fa necessari buscar solucions innovadores i efectives per a solucionar el problema que suposa la gestió d'aquests fangs biològics. Els fangs biològics són de naturalesa carbonosa i amb un alt contingut de matèria orgànica. Aquestes característiques, permeten la conversió del fang en un sòlid adsorbent de tipus carbonós. Aquesta conversió ofereix el doble benefici de reduir el volum de fang que ha de ser gestionat i alhora produir un adsorbent amb un cost inferior a la dels adsorbents convencionals (carbons actius comercials). Fins el moment, els tractaments alta temperatura han demostrat la seva efectivitat per du a terme el procés de transformació dels excedents de fang biològic en un sòlid adsorbent carbonós (carbó actiu). Com a alternativa a aquests processos a alta temperatura, es proposa un nou procés d'obtenció d'un sòlid adsorbent carbonós a partir dels excedents de fangs biològics, mitjançant un tractament a baixa temperatura, combinant el tractament per microones amb l'addició d'un reactiu químic (H2SO4). La present tesi analitza el tractament dels excedents de fangs biològics utilitzant un tractament mitjançant microones i l'addició d'àcid sulfúric (H2SO4), al mateix temps analitza la possibilitat d'utilitzar els sòlids adsorbents obtinguts per a millorar la qualitat de les aigües residuals. Paràmetres d'operació com poden ser la quantitat d'àcid sulfúric addicionada al fang, el nivell de potència del forn microones i el temps de tractament, es modificaran per tal de determinar la influència que poden tenir sobre la qualitat del sòlid adsorbent. Un cop determinada la qualitat dels diferent sòlids adsorbents s'avalua la seva capacitat per a l'eliminació de colorant i metalls en fase líquida. Els resultats obtinguts es comparen amb els obtinguts per un carbó actiu derivat de fangs i un carbó actiu comercial.

Avaluació de la toxicitat de metalls pesants i arsènic en diferents models biològics

En aquest estudi, la toxicitat de diversos metalls pesants i l'arsènic va ser analitzada utilitzant diferents models biològics. En la primera part d'aquest treball, el bioassaig de toxicitat Microtox, el qual està basat en la variació de l'emissió lumínica del bacteri luminiscent Vibrio fischeri, va ser utilitzat per establir les corbes dosi-resposta de diferents elements tòxics com el Zn(II), Pb(II), Cu(II), Hg(II), Ag(I), Co(II), Cd(II), Cr(VI), As(V) i As(III) en solucions aquoses. Els experiments es varen portar a terme a pH 6.0 i 7.0 per tal de mostrar que el pH pot influir en la toxicitat final mesurada d'alguns metalls degut als canvis relacionats amb la seva especiació química. Es varen trobar diferents tipus de corbes dosi-resposta depenent del metall analitzat i el pH del medi. En el cas de l'arsènic, l'efecte del pH en la toxicitat de l'arsenat i l'arsenit es va investigar utilitzant l'assaig Microtox en un rang de pHs comprès entre pH 5.0 i 9.0. Els valors d'EC50 determinats per l'As(V) disminueixen, reflectint un augment de la toxicitat, a mesura que el pH de la solució augmenta mentre que, en el cas de l'As(III), els valors d'EC50 quasi bé no varien entre pH 6.0 i 8.0 i només disminueixen a pH 9.0. HAsO42- i H2AsO3- es varen definir com les espècies més tòxiques. Així mateix, una anàlisi estadística va revelar un efecte antagònic entre les espècies químiques d'arsenat que es troben conjuntament a pH 6.0 i 7.0. D'altra banda, els resultats de dos mètodes estadístics per predir la toxicitat i les possibles interaccions entre el Co(II), Cd(II), Cu(II), Zn(II) i Pb(II) en mescles binàries equitòxiques es varen comparar amb la toxicitat observada sobre el bacteri Vibrio fischeri. L'efecte combinat d'aquests metalls va resultar ser antagònic per les mescles de Co(II)-Cd(II), Cd(II)-Zn(II), Cd(II)-Pb(II) i Cu(II)-Pb(II), sinèrgic per Co(II)-Cu(II) i Zn(II)-Pb(II) i additiu en els altres casos, revelant un patró complex de possibles interaccions. L'efecte sinèrgic de la combinació Co(II)-Cu(II) i la forta disminució de la toxicitat del Pb(II) quan es troba en presència de Cd(II) hauria de merèixer més atenció quan s'estableixen les normatives de seguretat ambiental. La sensibilitat de l'assaig Microtox també va ser determinada. Els valors d'EC20, els quals representen la toxicitat llindar mesurable, varen ser determinats per cada element individualment i es va veure que augmenten de la següent manera: Pb(II) < Ag(I) < Hg(II)  Cu(II) < Zn(II) < As(V) < Cd(II)  Co(II) < As(III) < Cr(VI). Aquests valors es varen comparar amb les concentracions permeses en aigues residuals industrials establertes per la normativa oficial de Catalunya (Espanya). L'assaig Microtox va resultar ser suficientment sensible per detectar els elements assajats respecte a les normes oficials referents al control de la contaminació, excepte en el cas del cadmi, mercuri, arsenat, arsenit i cromat. En la segona part d'aquest treball, com a resultats complementaris dels resultats previs obtinguts utilitzant l'assaig de toxicitat aguda Microtox, els efectes crònics del Cd(II), Cr(VI) i As(V) es varen analitzar sobre la taxa de creixement i la viabilitat en el mateix model biològic. Sorprenentment, aquests productes químics nocius varen resultar ser poc tòxics per aquest bacteri quan es mesura el seu efecte després de temps d'exposició llargs. Tot i això, en el cas del Cr(VI), l'assaig d'inhibició de la viabilitat va resultar ser més sensible que l'assaig de toxicitat aguda Microtox. Així mateix, també va ser possible observar un clar fenomen d'hormesis, especialment en el cas del Cd(II), quan s'utilitza l'assaig d'inhibició de la viabilitat. A més a més, diversos experiments es varen portar a terme per intentar explicar la manca de toxicitat de Cr(VI) mostrada pel bacteri Vibrio fischeri. La resistència mostrada per aquest bacteri podria ser atribuïda a la capacitat d'aquest bacteri de convertir el Cr(VI) a la forma menys tòxica de Cr(III). Es va trobar que aquesta capacitat de reducció depèn de la composició del medi de cultiu, de la concentració inicial de Cr(VI), del temps d'incubació i de la presència d'una font de carboni. En la tercera part d'aquest treball, la línia cel·lular humana HT29 i cultius primaris de cèl·lules sanguínies de Sparus sarba es varen utilitzar in vitro per detectar la toxicitat llindar de metalls mesurant la sobreexpressió de proteines d'estrès. Extractes de fangs precedents de diverses plantes de tractament d'aigues residuals i diferents metalls, individualment o en combinació, es varen analitzar sobre cultius cel·lulars humans per avaluar el seu efecte sobre la taxa de creixement i la capacitat d'induir la síntesi de les proteïnes Hsp72 relacionades amb l'estrès cel·lular. No es varen trobar efectes adversos significatius quan els components s'analitzen individualment. Nogensmenys, quan es troben conjuntament, es produeix un afecte advers sobre tan la taxa de creixement com en l'expressió de proteins d'estrès. D'altra banda, cèl·lules sanguínies procedents de Sparus sarba es varen exposar in vitro a diferents concentracions de cadmi, plom i crom. La proteïna d'estrès HSP70 es va sobreexpressar significativament després de l'exposició a concentracions tan febles com 0.1 M. Sota les nostres condicions de treball, no es va evidenciar una sobreexpressió de metal·lotioneïnes. Nogensmenys, les cèl·lules sanguínies de peix varen resultar ser un model biològic interessant per a ser utilitzat en anàlisis de toxicitat. Ambdós models biològics varen resultar ser molt adequats per a detectar acuradament la toxicitat produïda per metalls. En general, l'avaluació de la toxicitat basada en l'anàlisi de la sobreexpressió de proteïnes d'estrès és més sensible que l'avaluació de la toxicitat realitzada a nivell d'organisme. A partir dels resultats obtinguts, podem concloure que una bateria de bioassaigs és realment necessària per avaluar acuradament la toxicitat de metalls ja que existeixen grans variacions entre els valors de toxicitat obtinguts emprant diferents organismes i molts factors ambientals poden influir i modificar els resultats obtinguts.

Sub-irrigation of Petunia: benefits in dry summers

With the increasing frequency and magnitude of warmer days during the summer in the UK, bedding plants which were a traditional part of the urban green landscape are perceived as unsustainable and water-demanding. During recent summers when bans on irrigation have been imposed, use and sales of bedding plants have dropped dramatically having a negative financial impact on the nursery industry. Retaining bedding species as a feature in public and even private spaces in future may be conditional on them being managed in a manner that minimises their water use. Using Petunia x hybrida ‘Hurrah White’ we aimed to discover which irrigation approach was the most efficient for maintaining plants’ ornamental quality (flower numbers, size and longevity), shoot and root growth under water deficit and periods of complete water withdrawal. Plants were grown from plugs for 51 days in wooden rhizotrons (0.35 m (h) x 0.1 m (w) x 0.065 m (d)); the rhizotrons’ front comprised clear Perspex which enabled us to monitor root growth closely. Irrigation treatments were: 1. watering with the amount which constitutes 50% of container capacity by conventional surface drip-irrigation (‘50% TOP’); 2. 50% as sub-irrigation at 10 cm depth (‘50% SUB’); 3. ‘split’ irrigation: 25% as surface drip- and 25% as sub-irrigation at 15 cm depth (‘25/25 SPLIT’); 4. 25% as conventional surface drip-irrigation (‘25% TOP’). Plants were irrigated daily at 18:00 apart from days 34-36 (inclusive) when water was withdrawn for all the treatments. Plants in ‘50% SUB’ had the most flowers and their size was comparable to that of ‘50% TOP’. Differences between treatments in other ‘quality’ parameters (height, shoot number) were biologically small. There was less root growth at deeper soil surface levels for ‘50% TOP’ which indicated that irrigation methods like ‘50% SUB’ and ‘25/25 SPLIT’ and stronger water deficits encouraged deeper root growth. It is suggested that sub-irrigation at 10 cm depth with water amounts of 50% container capacity would result in the most root growth with the maximum flowering for Petunia. Leaf stomatal conductance appeared to be most sensitive to the changes in substrate moisture content in the deepest part of the soil profile, where most roots were situated.

Acidity controls on dissolved organic carbon mobility in organic soils

Dissolved organic carbon (DOC) concentrations in surface waters have increased across much of Europe and North America, with implications for the terrestrial carbon balance, aquatic ecosystem functioning, water treatment costs and human health. Over the past decade, many hypotheses have been put forward to explain this phenomenon, from changing climate and land-management to eutrophication and acid deposition. Resolution of this debate has been hindered by a reliance on correlative analyses of time-series data, and a lack of robust experimental testing of proposed mechanisms. In a four-year, four-site replicated field experiment involving both acidifying and de-acidifying treatments, we tested the hypothesis that DOC leaching was previously suppressed by high levels of soil acidity in peat and organo-mineral soils, and therefore that observed DOC increases a consequence of decreasing soil acidity. We observed a consistent, positive relationship between DOC and acidity change at all sites. Responses were described by similar hyperbolic relationships between standardised changes in DOC and hydrogen ion concentrations at all sites, suggesting potentially general applicability. These relationships explained a substantial proportion of observed changes in peak DOC concentrations in nearby monitoring streams, and application to a UK-wide upland soil pH dataset suggests that recovery from acidification alone could have led to soil solution DOC increases in the range 46-126% by habitat type since 1978. Our findings raise the possibility that changing soil acidity may have wider impacts on ecosystem carbon balances. Decreasing sulphur deposition may be accelerating terrestrial carbon loss, and returning surface waters to a natural, high-DOC condition.

Nitrogen speciation and phosphorus fractionation dynamics in a lowland chalk catchment

A detailed analysis of temporal and spatial trends in nitrogen (N) speciation and phosphorus (P) fractionation in the Wylye, a lowland Chalk sub-catchment of the Hampshire Avon, UK is presented, identifying the sources contributing to nutrient enrichment, and temporal variability in the fractionation of nutrients in transit from headwaters to lower reaches of the river. Samples were collected weekly from ten monitoring stations with daily sampling at three further sites over one year, and monthly inorganic N and total reactive P (TRP) concentrations at three of the ten weekly monitoring stations over a ten year period are also presented. The data indicate significant daily and seasonal variation in nutrient fractionation in the water column, resulting from plant uptake of dissolved organic and inorganic nutrient fractions in the summer months, increased delivery of both N and P from diffuse sources in the autumn to winter period and during high flow events, and lack of dilution of point source discharges to the Wylye from septic tank, small package Sewage Treatment Works (STW) and urban Waste Water Treatment Works (WwTW) during the summer low flow period. Weekly data show that contributing source areas vary along the river with headwater N and P strongly influenced by diffuse inorganic N and particulate P fluxes, and SRP and organic-rich point source contributions from STW and WwTW having a greater influence in the lower reaches. Long-term data show a decrease in TRP concentrations at all three monitoring stations, with the most pronounced decrease occurring downstream from Warminster WwTW, following the introduction of P stripping at the works in 2001. Inorganic N demonstrates no statistically significant change over the ten year period of record in the rural headwaters, but an increase in the lower reaches downstream from the WwTW which may be due to urban expansion in the lower catchment.

Endophytic bacterial community composition in wheat (Triticum aestivum) is determined by plant tissue type, developmental stage and soil nutrient availability

Aims: To understand effects of tissue type, growth stage and soil fertilisers on bacterial endophyte communities of winter wheat (Triticum aestivum cv. Hereward). Methods: Endophytes were isolated from wheat grown under six fertiliser conditions in the long term Broadbalk Experiment at Rothamsted Research, UK. Samples were taken in May and July from root and leaf tissues. Results: Root and leaf communities differed in abundance and composition of endophytes. Endophytes were most abundant in roots and the Proteobacteria were most prevalent. In contrast, Firmicutes and Actinobacteria, the Gram positive phyla, were most prevalent in the leaves. Both fertiliser treatment and sample time influenced abundance and relative proportions of each phylum and genus in the endosphere. A higher density of endophytes was found in the Nil input treatment plants. Conclusions: Robust isolation techniques and stringent controls are critical for accurate recovery of endophytes. The plant tissue type, plant growth stage, and soil fertiliser treatment all contribute to the composition of the endophytic bacterial community in wheat. These results should help facilitate targeted development of endophytes for beneficial applications in agriculture.

On site flotation for recovering polluted aquatic systems: is it a feasible solution for a Brazilian urban river?

Pinheiros River (Brazil) plays a pivotal role in supplying water to Billings Reservoir, which presents multiple uses (human drinking, energy generation, irrigation, navigation, fishing and leisure) An intense monitoring program was performed during the years 2007 and 2008 to find out whether on site flotation is a feasible solution or not for improving the water quality of this urban river, attenuating the pollutants load caused by the water pumping to the reservoir (approximately 10 m(3)s(-1)) The monitoring of 18 variables (13,429 laboratorial analysis during the period of 490 days), suggested that despite the convenience of the on site approach for water treatment, especially for rivers located in fully urbanized areas, the flotation system is not enough itself to recover Pinheiros River water quality, given the several constraints that apply Total phosphorus removal was high in percentage terms (about 90%), although the remaining concentrations were not so low (mean of 0 05 mg L(-1)) The removal efficiency of some variables was insufficient, leading to high final mean concentrations of metals [e g aluminium (0 29 mg L(-1)), chromium (0 02 mg L(-1)) and iron (1 1 mg L(-1))] as well as nitrogen-ammonia (25 8 mg L(-1)) and total suspended solids (18 mg L(-1)) in the treated water