Ultra-low friction coefficient in alumina-silicon nitride pair lubricated with water

In a ball-on-disc wear test, an alumina ceramic body sliding against a silicon nitride ceramic body in water achieved an ultra-low friction coefficient (ULFC) of 0.004. The profilometer and EDX measurements indicated that the ULFC regime in this unmated Al2O3-Si3N4 pair was achieved because of the formation of a flat and smooth interface of nanometric roughness, which favored the hydrodynamic lubrication. The triboreactions formed silicon and aluminum hydroxides which contributed to decrease roughness and shear stress at the contact interface. This behavior enables the development of low energy loss water-based tribological systems using oxide ceramics. 13 2012 Elsevier B.V. All rights reserved.

The effect of curing light and chemical catalyst on the degree of conversion of two dual cured resin luting cements

The aim of this study was to evaluate the influence of different curing lights and chemical catalysts on the degree of conversion of resin luting cements. A total of 60 disk-shaped specimens of RelyX ARC or Panavia F of diameter 5 mm and thickness 0.5 mm were prepared and the respective chemical catalyst (Scotchbond Multi-Purpose Plus or ED Primer) was added. The specimens were light-cured using different curing units (an argon ion laser, an LED or a quartz-tungsten-halogen light) through shade A2 composite disks of diameter 10 mm and thickness 2 mm. After 24 h of dry storage at 37A degrees C, the degree of conversion of the resin luting cements was measured by Fourier-transformed infrared spectroscopy. For statistical analysis, ANOVA and the Tukey test were used, with p a parts per thousand currency signaEuro parts per thousand 0.05. Panavia F when used without catalyst and cured using the LED or the argon ion laser showed degree of conversion values significantly lower than RelyX ARC, with and without catalyst, and cured with any of the light sources. Therefore, the degree of conversion of Panavia F with ED Primer cured with the quartz-tungsten-halogen light was significantly different from that of RelyX ARC regardless of the use of the chemical catalyst and light curing source. In conclusion, RelyX ARC can be cured satisfactorily with the argon ion laser, LED or quartz-tungsten-halogen light with or without a chemical catalyst. To obtain a satisfactory degree of conversion, Panavia F luting cement should be used with ED Primer and cured with halogen light.

Effect of light sources and curing mode techniques on sorption, solubility and biaxial flexural strength of a composite resin

Adequate polymerization plays an important role on the longevity of the composite resin restorations. Objectives: The aim of this study was to evaluate the effect of light-curing units, curing mode techniques and storage media on sorption, solubility and biaxial flexural strength (BFS) of a composite resin. Material and Methods: Two hundred and forty specimens were made of one composite resin (Esthet-X) in a stainless steel mold (2 mm x 8 mm 0), and divided into 24 groups (n=10) established according to the 4 study factors: light-curing units: quartz tungsten halogen (QTH) lamp and light-emitting diodes (LED); energy densities: 16 J/cm(2) and 20 J/cm(2); curing modes: conventional (CM) and pulse-delay (PD); and permeants: deionized water and 75% ethanol for 28 days. Sorption and solubility tests were performed according to ISO 4049:2000 specifications. All specimens were then tested for BFS according to ASTM F394-78 specification. Data were analyzed by three-way ANOVA followed by Tukey, Kruskal-Wallis and Mann-Whitney tests (alpha=0.05). Results: In general, no significant differences were found regarding sorption, solubility or BFS means for the light-curing units and curing modes (p>0.05). Only LED unit using 16 J/cm(2) and PD using 10 s produced higher sorption and solubility values than QTH. Otherwise, using CM (16 J/cm(2)), LED produced lower values of BFS than QTH (p<0.05). 75% ethanol permeant produced higher values of sorption and solubility and lower values of BFS than water (p<0.05). Conclusion: Ethanol storage media produced more damage on composite resin than water. In general the LED and QTH curing units using 16 and 20 J/cm(2) by CM and PD curing modes produced no influence on the sorption, solubility or BFS of the tested resin.

Microstructural characterization of as-cast hf-b alloys

An accurate knowledge of several metal-boron phase diagrams is important to evaluation of higher order systems such as metal-silicon-boron ternaries. The refinement and reassessment of phase diagram data is a continuous work, thus the reevaluation of metal-boron systems provides the possibility to confirm previous data from an investigation using higher purity materials and better analytical techniques. This work presents results of rigorous microstructural characterization of as-cast hafnium-boron alloys which are significant to assess the liquid composition associated to most of the invariant reactions of this system. Alloys were prepared by arc melting high purity hafnium (minimum 99.8%) and boron (minimum 99.5%) slices under argon atmosphere in water-cooled copper crucible with non consumable tungsten electrode and titanium getter. The phases were identified by scanning electron microscopy, using back-scattered electron image mode and X-ray diffraction. In general, a good agreement was found between our data and those from the currently accepted Hafnium-Boron phase diagram. The phases identified are αHfSS and B-RhomSS, the intermediate compounds HfB and HfB2 and the liquide L. The reactions are the eutectic L ⇔ αHfSS + HfB and L ⇔ HfB2 + B-Rhom, the peritectic L + HfB2 ⇔ HfB and the congruent formation of HfB2.

Concentration quenching and thermal activation of the luminescence from terbium-doped a-SiC:H and c-AlN thin films

The effect of terbium (Tb) doping on the photoluminescence (PL) of crystalline aluminum nitride (c-AlN) and amorphous hydrogenated silicon carbide (a-SiC:H) thin films has been investigated for different Tb atomic concentrations. The samples were prepared by DC and RF magnetron reactive sputtering techniques covering the concentration range of Tb from 0.5 to 11 at.%. The Tb-related light emission versus the Tb concentration is reported for annealing temperatures of 450 °C, 750 °C and 1000 °C. In the low concentration region the intensity exhibits a linear increase and its slope is enhanced with the annealing temperature giving an activation energy of 0.106 eV in an Arrhenius plot. In the high concentration region an exponential decay is recorded which is almost independent on the host material, its structure and the annealing process.

Preparation and characterisation of refractory whiskers and selected alumina composites

A whisker is a common name of single crystalline inorganic fibre of small dimensions, typically 0.5-1 μm in diameter and 20-50 μm in length. Whiskers are mainly used as reinforcement of ceramics. This work describes the synthesis and characterisation of new whisker types. Ti0.33Ta0.33Nb0.33CxN1-x, TiB2, B4C, and LaxCe1-xB6 have been prepared by carbothermal vapour–liquid–solid (CTR-VLS) growth mechanisms in the temperature range 900-1800°C, in argon or nitrogen. Generally, carbon and different suitable oxides were used as whisker precursors. The oxides reacted via a carbothermal reduction process. A halogenide salt was added to form gaseous metal halogenides or oxohalogenides and small amount of a transition metal was added to catalyse the whisker growth. In this mechanism, the whisker constituents are dissolved into the catalyst, in liquid phase, which becomes supersaturated. Then a whisker could nucleate and grow out under continuous feed of constituents. The syntheses of TiC, TiB2, and B4C were followed at ordinary synthesis conditions by means of mass spectrometry (MS), thermogravimetry (TG), differential thermal analysis (DTA) and quenching. The main reaction starting temperatures and reaction time for the different mixtures was revealed, and it was found that the temperature inside the crucible during the reactions was up to 100°C below the furnace set-point, due to endothermic nature of the reactions. Quench experiments showed that whiskers were formed already when reaching the temperature plateau, but the yield increased fast with the holding time and reached a maximum after about 20-30 minutes. Growth models for whisker formation have been proposed. Alumina based composites reinforced by (2-5 vol.%) TiCnano and TiNnano and 25 vol.% of carbide, and boride phases (whiskers and particulates of TiC, TiN, TaC, NbC, (Ti,Ta)C, (Ti,Ta,Nb)C, SiC, TiB2 and B4C) have been prepared by a developed aqueous colloidal processing route followed by hot pressing for 90 min at 1700°C, 28 MPa or SPS sintering for 5 minutes at 1200-1600°C and 75 MPa. Vickers indentation measurements showed that the lowest possible sintering temperature is to prefer from mechanical properties point of view. In the TiNnano composites the fracture mode was typically intergranular, while it was transgranular in the SiCnano composites. The whisker and particulate composites have been compared in terms of e.g. microstructure and mechanical properties. Generally, additions of whiskers yielded higher fracture toughness compared to particulates. Composites of commercially available SiC whiskers showed best mechanical properties with a low spread but all the other whisker phases, especially TiB2, exhibited a great potential as reinforcement materials.

Aspetti innovativi per la valutazione e la misura della porosità nei materiali dell'edilizia antica e moderna. La geometria frattale della porosità

New concepts on porosity appraisal in ancient and modern construction materials. The role of Fractal Geometry on porosity characterization and transport phenomena. This work studied the potential of Fractal Geometry to the characterization of porous materials. Besides the descriptive aspects of the pore size distribution, the fractal dimensions have led to the development of rational relations for the prediction of permeability coefficients to fluid and heat transfer. The research considered natural materials used in historical buildings (rock and earth) as well as currently employed materials as hydraulic cement and technologically advanced materials such as silicon carbide or YSZ ceramics. The experimental results of porosity derived from the techniques of mercury intrusion and from the image analysis. Data elaboration was carried out according to established procedures of Fractal Geometry. It was found that certain classes of materials are clearly fractal and respond to simple patterns such as Sierpinski and Menger models. In several cases, however, the fractal character is not recognised because the microstructure of the material is based on different phases at different dimensional scales, and in consequence the “fractal dimensions” calculated from porosimetric data do not come within the standard range (less than 3). Using different type and numbers of fractal units is possible, however, to obtain “virtual” microstructures that have the fraction of voids and pore size distribution equivalent with the experimental ones for almost any material. Thus it was possible to take the expressions for the permeability and the thermal conduction which does not require empirical “constants”, these expressions have also provided values that are generally in agreement with the experimental available data. More problematic has been the fractal discussion of the geometry of the rupture of the material subjected to mechanical stress both external and internal applied. The results achieved on these issues are qualitative and prone to future studies. Keywords: Materials, Microstructure, Porosity, Fractal Geometry, Permeability, Thermal conduction, Mechanical strength.

Development and characterization of non-oxide ceramic composites for mechanical and tribological applications

The main reasons for the attention focused on ceramics as possible structural materials are their wear resistance and the ability to operate with limited oxidation and ablation at temperatures above 2000°C. Hence, this work is devoted to the study of two classes of materials which can satisfy these requirements: silicon carbide -based ceramics (SiC) for wear applications and borides and carbides of transition metals for ultra-high temperatures applications (UHTCs). SiC-based materials: Silicon carbide is a hard ceramic, which finds applications in many industrial sectors, from heat production, to automotive engineering and metals processing. In view of new fields of uses, SiC-based ceramics were produced with addition of 10-30 vol% of MoSi2, in order to obtain electro conductive ceramics. MoSi2, indeed, is an intermetallic compound which possesses high temperature oxidation resistance, high electrical conductivity (21·10-6 Ω·cm), relatively low density (6.31 g/cm3), high melting point (2030°C) and high stiffness (440 GPa). The SiC-based ceramics were hot pressed at 1900°C with addition of Al2O3-Y2O3 or Y2O3-AlN as sintering additives. The microstructure of the composites and of the reference materials, SiC and MoSi2, were studied by means of conventional analytical techniques, such as X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive spectroscopy (SEM-EDS). The composites showed a homogeneous microstructure, with good dispersion of the secondary phases and low residual porosity. The following thermo-mechanical properties of the SiC-based materials were measured: Vickers hardness (HV), Young’s modulus (E), fracture toughness (KIc) and room to high temperature flexural strength (σ). The mechanical properties of the composites were compared to those of two monolithic SiC and MoSi2 materials and resulted in a higher stiffness, fracture toughness and slightly higher flexural resistance. Tribological tests were also performed in two configurations disco-on-pin and slideron cylinder, aiming at studying the wear behaviour of SiC-MoSi2 composites with Al2O3 as counterfacing materials. The tests pointed out that the addition of MoSi2 was detrimental owing to a lower hardness in comparison with the pure SiC matrix. On the contrary, electrical measurements revealed that the addition of 30 vol% of MoSi2, rendered the composite electroconductive, lowering the electrical resistance of three orders of magnitude. Ultra High Temperature Ceramics: Carbides, borides and nitrides of transition metals (Ti, Zr, Hf, Ta, Nb, Mo) possess very high melting points and interesting engineering properties, such as high hardness (20-25 GPa), high stiffness (400-500 GPa), flexural strengths which remain unaltered from room temperature to 1500°C and excellent corrosion resistance in aggressive environment. All these properties place the UHTCs as potential candidates for the development of manoeuvrable hypersonic flight vehicles with sharp leading edges. To this scope Zr- and Hf- carbide and boride materials were produced with addition of 5-20 vol% of MoSi2. This secondary phase enabled the achievement of full dense composites at temperature lower than 2000°C and without the application of pressure. Besides the conventional microstructure analyses XRD and SEM-EDS, transmission electron microscopy (TEM) was employed to explore the microstructure on a small length scale to disclose the effective densification mechanisms. A thorough literature analysis revealed that neither detailed TEM work nor reports on densification mechanisms are available for this class of materials, which however are essential to optimize the sintering aids utilized and the processing parameters applied. Microstructural analyses, along with thermodynamics and crystallographic considerations, led to disclose of the effective role of MoSi2 during sintering of Zrand Hf- carbides and borides. Among the investigated mechanical properties (HV, E, KIc, σ from room temperature to 1500°C), the high temperature flexural strength was improved due to the protective and sealing effect of a silica-based glassy phase, especially for the borides. Nanoindentation tests were also performed on HfC-MoSi2 composites in order to extract hardness and elastic modulus of the single phases. Finally, arc jet tests on HfC- and HfB2-based composites confirmed the excellent oxidation behaviour of these materials under temperature exceeding 2000°C; no cracking or spallation occurred and the modified layer was only 80-90 μm thick.

Untersuchung magnetischer Nanostrukturen mittels Rastertunnelspektroskopie und Kerr-Magnetometrie am Beispiel von Fe, Co, Co-Fe und Fe-Mn Nanostrukturen

Nach einer kurzen Einführung in die Entwicklung der magnetischen Anwendungen, werden in Kapitel 2 und 3 die physikalischen Grundlagen der Messmethoden, insbesondere die Rastertunnelspektroskopie und Kerr-Magnetometrie, sowie der experimentelle Aufbau erläutert. Kapitel 4 beschäftigt sich mit den magnetischen Eigenschaften von quasi ein-dimensionalen ferromagnetischen Nanostreifen und Monolagen, die durch Selbstorganisation auf einem Wolfram(110)-Einkristall mit vizinaler und glatter Oberfläche präpariert werden. Hierbei wird die Temperaturabhängigkeit der magnetischen Größen, wie Remanenz, Sättigungsmagnetisierung und Suszeptibilität, sowie die Auswirkung einer Abdeckung des Systems auf die Domänenwandenergie und Anisotropie untersucht. Zusätzlich wird die Kopplung von parallelen Nanostreifen in Abhängigkeit des Streifenabstandes betrachtet. In Kapitel 5 werden das Wachstum und die Morphologie von Co-Monolagen auf W(110) untersucht. Der Übergang von pseudomorphem zu dicht gepacktem Wachstum in der Monolage wird mit Hilfe der Rastertunnelspektroskopie sichtbar gemacht, ebenso wie unterschiedliche Stapelfolgen in Tripellagen Co-Systemen. Atomar aufgelöste Rastertunnelmikroskopie erlaubt die genauen Atompositionen der Oberfläche zu bestimmen und mit theoretischen Wachstumsmodellen zu vergleichen. Auf die Untersuchung zwei-dimensionaler binärer Co-Fe und Fe-Mn Legierungen auf W(110) wird in Kapitel 6 eingegangen. Mit einer Präparationstemperatur von T=520 K ist es möglich, atomar geordnete Co-Fe Legierungsmonolagen wachsen zu lassen. Ein direkter Zusammenhang zwischen der Magnetisierung und der lokalen Zustandsdichte in Abhängigkeit der Legierungszusammensetzung wird gezeigt.

Photoemissions-Elektronenmikroskopie an Adsorbatsystemen

Die Photoemissions-Elektronenmikroskopie ist eine hervorragend geeignete Methode zur Untersuchung dynamischer Vorgänge auf realen polykristallinen Oberflächen im sub-μm Bereich. Bei der Anwendung auf Adsorbatsysteme lassen sich geringe Bedeckungsunterschiede, sowie Adsorbatstrukturen und -phasen unterscheiden. Die Methode erlaubt dabei ein breites Anwendungsspektrum über weite Temperaturbereiche und Systeme unterschiedlichster Bindungsenergie. Bei der Chemisorption von Sauerstoff auf polykristallinen Metallen wird unterschiedliches Aufwachsverhalten in den Helligkeitswerten im Mikroskopbild widergespiegelt. Bei Kupferproben zeigen Oberflächen mit unterschiedlicher kristalliner Richtung aufgrund der Symmetrie des fcc-Gitters ein ähnliches Verhalten. Das hexagonale Gitter des Titans zeigt dagegen große Unterschiede im Adsorptionsverhalten in Abhängigkeit der kristallinen Richtung. Diese Unterschiede konnten auf verschiedene Haftkoeffizienten und Oxidationsstufen der Metalle zurückgeführt werden. In einem Modell zur Photostromanalyse konnte beim Kupfer der Übergang von verschiedenen Überstrukturen bei wachsender Bedeckung gezeigt und die Übergänge ermittelt werden.. Auf den Titanoberflächen wurde so das Wachstum der Oxide TiO, TiO₂ und Ti₂O₃ unterschieden und die Übergänge des unterschiedlichen Wachstums ermittelt. Bei der thermischen Desorption der Schichten konnten unterschiedliche Haftkoeffizient auf einzelnen Kristalliten qualitativ gezeigt werden. Diese erstmalig eingesetzte Analysemethode weist Ähnlichkeiten zur Thermo-Desorptions-Spektroskopie (TDS) auf, zeigt jedoch ortsaufgelöst lokale Unterschiede auf polykristallinen Oberflächen. Bei thermisch gestützten Oberflächenreaktionen ließen sich die Reaktionskeime deutlich identifizieren und mit einer Grauwertanalyse konnte die Oxidation der karbidischen Lagen zu Kohlenmonoxid und die Metalloxidation unterschieden werden. Dabei konnte gezeigt werden, daß die Reaktionskeime nur an Plattengrenzen auftreten, nicht jedoch auf der Oberfläche. Durch die Aufrauhung der Plattengrenzen mit zunehmender Reaktionsdauer nimmt die Zahl der Reaktionskeime kontinuierlich zu, die laterale Ausdehnung der Einzelreaktionen bleibt aber konstant. Bei der Physisorption von Xenon auf Graphit wurde erstmals für die Photoemissionsmikroskopie die resonanten Anregung ausgenutzt. Die verschiedenen Phasen des Adsorbats können dabei deutlich unterschieden werden; bei niedrigen Temperaturen (40K) findet ein gleichmäßiges Wachstum auf der gesamten Oberfläche statt, bei höheren Temperaturen von 60-65K ist dagegen ein Inselwachstum in verschiedenen Phasen zu beobachten. Die zeitliche Entwicklung des Wachstums, die örtliche Lage der Phasen und die Phasenübergänge (gas, fest inkommensurabel, fest kommensurabel) konnten bestimmt werden. Bei der Desorption der Schichten konnten die einzelnen Phasen ebenfalls getrennt werden und das unterschiedliche Desorptionsverhalten sowie die Phasenübergänge selber verifiziert werden.

Sviluppo, ottimizzazione delle prestazioni e caratterizzazione di materiali compositi a matrice amorfa

Durante l'attività di ricerca sono stati sviluppati tre progetti legati allo sviluppo e ottimizzazione di materiali compositi. In particolare, il primo anno, siamo andati a produrre materiali ceramici ultrarefrattari tenacizzati con fibre di carburo di silicio, riuscendo a migliorare il ciclo produttivo e ottenendo un materiale ottimizzato. Durante il secondo anno di attività ci siamo concentrati nello sviluppo di resine epossidiche rinforzate con particelle di elastomeri florurati che rappresentano un nuovo materiale non presente nel mercato utile per applicazioni meccaniche e navali. L'ultimo anno di ricerca è stato svolto presso il laboratorio materiali di Ansaldo Energia dove è stato studiato il comportamenteo di materiali per turbine a gas.

Developments for transactinide chemistry experiments behind the gas-filled separator TASCA

Topic of this thesis is the development of experiments behind the gas-filled separator TASCA(TransActinide Separator and Chemistry Apparatus) to study the chemical properties of the transactinide elements.rnIn the first part of the thesis, the electrodepositions of short-lived isotopes of ruthenium and osmium on gold electrodes were studied as model experiments for hassium. From literature it is known that the deposition potential of single atoms differs significantly from the potential predicted by the Nernst equation. This shift of the potential depends on the adsorption enthalpy of therndeposited element on the electrode material. If the adsorption on the electrode-material is favoured over the adsorption on a surface made of the same element as the deposited atom, the electrode potential is shifted to higher potentials. This phenomenon is called underpotential deposition.rnPossibilities to automatize an electro chemistry experiment behind the gas-filled separator were explored for later studies with transactinide elements.rnThe second part of this thesis is about the in-situ synthesis of transition-metal-carbonyl complexes with nuclear reaction products. Fission products of uranium-235 and californium-249 were produced at the TRIGA Mainz reactor and thermalized in a carbon-monoxide containing atmosphere. The formed volatile metal-carbonyl complexes could be transported in a gas-stream.rnFurthermore, short-lived isotopes of tungsten, rhenium, osmium, and iridium were synthesised at the linear accelerator UNILAC at GSI Helmholtzzentrum für Schwerionenforschung, Darmstadt. The recoiling fusion products were separated from the primary beam and the transfer products in the gas-filled separator TASCA. The fusion products were stopped in the focal plane of TASCA in a recoil transfer chamber. This chamber contained a carbon-monoxide – helium gas mixture. The formed metal-carbonyl complexes could be transported in a gas stream to various experimental setups. All synthesised carbonyl complexes were identified by nuclear decay spectroscopy. Some complexes were studied with isothermal chromatography or thermochromatography methods. The chromatograms were compared with Monte Carlo Simulations to determine the adsorption enthalpyrnon silicon dioxide and on gold. These simulations based on existing codes, that were modified for the different geometries of the chromatography channels. All observed adsorption enthalpies (on silcon oxide as well as on gold) are typical for physisorption. Additionally, the thermalstability of some of the carbonyl complexes was studied. This showed that at temperatures above 200 °C therncomplexes start to decompose.rnIt was demonstrated that carbonyl-complex chemistry is a suitable method to study rutherfordium, dubnium, seaborgium, bohrium, hassium, and meitnerium. Until now, only very simple, thermally stable compounds have been synthesized in the gas-phase chemistry of the transactindes. With the synthesis of transactinide-carbonyl complexes a new compound class would be discovered. Transactinide chemistry would reach the border between inorganic and metallorganic chemistry.rnFurthermore, the in-situ synthesised carbonyl complexes would allow nuclear spectroscopy studies under low background conditions making use of chemically prepared samples.

Nanocrystalline Silicon Based Films for Renewable Energy Applications

The present thesis is focused on the study of innovative Si-based materials for third generation photovoltaics. In particular, silicon oxi-nitride (SiOxNy) thin films and multilayer of Silicon Rich Carbide (SRC)/Si have been characterized in view of their application in photovoltaics. SiOxNy is a promising material for applications in thin-film solar cells as well as for wafer based silicon solar cells, like silicon heterojunction solar cells. However, many issues relevant to the material properties have not been studied yet, such as the role of the deposition condition and precursor gas concentrations on the optical and electronic properties of the films, the composition and structure of the nanocrystals. The results presented in the thesis aim to clarify the effects of annealing and oxygen incorporation within nc-SiOxNy films on its properties in view of the photovoltaic applications. Silicon nano-crystals (Si NCs) embedded in a dielectric matrix were proposed as absorbers in all-Si multi-junction solar cells due to the quantum confinement capability of Si NCs, that allows a better match to the solar spectrum thanks to the size induced tunability of the band gap. Despite the efficient solar radiation absorption capability of this structure, its charge collection and transport properties has still to be fully demonstrated. The results presented in the thesis aim to the understanding of the transport mechanisms at macroscopic and microscopic scale. Experimental results on SiOxNy thin films and SRC/Si multilayers have been obtained at macroscopical and microscopical level using different characterizations techniques, such as Atomic Force Microscopy, Reflection and Transmission measurements, High Resolution Transmission Electron Microscopy, Energy-Dispersive X-ray spectroscopy and Fourier Transform Infrared Spectroscopy. The deep knowledge and improved understanding of the basic physical properties of these quite complex, multi-phase and multi-component systems, made by nanocrystals and amorphous phases, will contribute to improve the efficiency of Si based solar cells.

Glycerol oxidehydration to acrylic acid on complex mixed-metal oxides

The project of this Ph.D. thesis is based on a co-supervised collaboration between Università di Bologna, ALMA MATER STUDIORUM (Italy) and Instituto de Tecnología Química, Universitat Politècnica de València ITQ-UPV (Spain). This Ph.D. thesis is about the synthesis, characterization and catalytic testing of complex mixed-oxide catalysts mainly related to the family of Hexagonal Tungsten Bronzes (HTBs). These materials have been little explored as catalysts, although they have a great potential as multifunctional materials. Their peculiar acid properties can be coupled to other functionalities (e.g. redox sites) by isomorphous substitution of tungsten atoms with other transition metals such as vanadium, niobium and molybdenum. In this PhD thesis, it was demonstrated how it is possible to prepare substituted-HTBs by hydrothermal synthesis; these mixed-oxide were fully characterize by a number of physicochemical techniques such as XPS, HR-TEM, XAS etc. They were also used as catalysts for the one-pot glycerol oxidehydration to acrylic acid; this reaction might represent a viable chemical route to solve the important issue related to the co-production of glycerin along the biodiesel production chain. Acrylic acid yields as high as 51% were obtained and important structure-reactivity correlations were proved to govern the catalytic performance; only fine tuning of acid and redox properties as well as the in-framework presence of vanadium are fundamental to achieve noteworthy yields into the acid monomer. The overall results reported herein might represent an important contribution for future applications of HTBs in catalysis as well as a general guideline for a multifaceted approach for their physicochemical characterization.

Progettazione e realizzazione di un convertitore monofase in sic per applicazioni fotovoltaiche

Negli ultimi anni si è assistito ad un notevole sviluppo e diffusione dei sistemi di produzione di energia rinnovabile, in particolar modo di sistemi eolici e fotovoltaici. La sempre maggior richiesta di energia e la necessità di far fronte ai problemi di inquinamento sempre più intenso, a causa dei combustibili fossili, ha portato ad una crescita nell’interesse ad adottare queste nuove tecnologie per il sostentamento energetico della popolazione. In seguito all’adozione di tali sistemi si è verificata un’intensificazione della ricerca e dello sviluppo tecnologico in tale ambito al fine di massimizzare la produzione dell’energia. Un ruolo chiave nella gestione dell’energia ed in particolar modo l’interfacciamento del sistema di produzione con il carico è svolto elettronica di potenza. L’obiettivo principale della ricerca in tale ambito consiste nella individuazione di nuove tecnologie che permettano un incremento dell’efficienza di conversione anche di soli pochi punti percentuale. L’attività di tesi, svolta presso il LEMAD (Laboratorio di Macchine e Azionamenti del Dipartimento DEI), è stata quindi focalizzata nella progettazione e in seguito realizzazione di un convertitore per applicazioni fotovoltaiche. L’interesse nei confronti delle nuovetecnologie ha portato ad una scelta innovativa per quanto riguarda la configurazione dell’inverter costituente il convertitore. Tale configurazione, che prende il nome di Full Bridge DC Bypass o più semplicemente ponte H6, ha permesso la realizzazione di un convertitore compatto poiché non necessitante di un trasformatore per garantire l’isolamento tra i moduli PV e la rete. Inoltre l’adozione di due switch aggiuntivi rispetto ad un comune ponte H ha garantito una notevole riduzione delle perdite dovute alla tensione di modo comune(CMV)con conseguente incremento dell’efficienza. La ricerca di nuove tecnologie non è stata concentrata solamente nello studio di nuove configurazioni di inverter ma anche nell’individuazione di innovativi dispositivi di potenza. In particolar modo il silicon carbide o SiC ha dimostrato in diverse occasioni di essere un materiale superiore al silicio nelle applicazioni di potenza. Sono stati quindi realizzati due convertitori utilizzanti due differenti dispositivi di potenza (MOSFET in SiC e IGBT in Si)in modo tale da determinare le diverse prestazioni. Un ulteriore studio è stato svolto sulle tecniche di modulazione al fine di valutarne le differenti caratteristiche ed individuare quella più conveniente nella conversione utilizzante il ponte H6.