Mitigation of lower order harmonics in a grid-connected single-phase PV inverter

In this paper, a simple single-phase grid-connected photovoltaic (PV) inverter topology consisting of a boost section, a low-voltage single-phase inverter with an inductive filter, and a step-up transformer interfacing the grid is considered. Ideally, this topology will not inject any lower order harmonics into the grid due to high-frequency pulse width modulation operation. However, the nonideal factors in the system such as core saturation-induced distorted magnetizing current of the transformer and the dead time of the inverter, etc., contribute to a significant amount of lower order harmonics in the grid current. A novel design of inverter current control that mitigates lower order harmonics is presented in this paper. An adaptive harmonic compensation technique and its design are proposed for the lower order harmonic compensation. In addition, a proportional-resonant-integral (PRI) controller and its design are also proposed. This controller eliminates the dc component in the control system, which introduces even harmonics in the grid current in the topology considered. The dynamics of the system due to the interaction between the PRI controller and the adaptive compensation scheme is also analyzed. The complete design has been validated with experimental results and good agreement with theoretical analysis of the overall system is observed.

An approach for assessing the accuracy of accelerometer responses during axial impact tests

The primary objective of the present study is to show that for the most common configuration of an impactor system, the accelerometer cannot exactly reproduce the dynamic response of a specimen subjected to impact loading. An equivalent Lumped Parameter Model (LPM) of the given impactor set-up has been formulated for assessing the accuracy of an accelerometer mounted in a drop-weight impactor set-up for an axially loaded specimen. A specimen under the impact loading is represented by a non-linear spring of varying stiffness, while the accelerometer is assumed to behave in a linear manner due to its high stiffness. Specimens made of steel, aluminium and fibre-reinforced composite (FRC) are used in the present study. Assuming the force-displacement response obtained in an actual impact test to be the true behaviour of the test specimen, a suitable numerical approach has been used to solve the governing non-linear differential equations of a three degrees-of-freedom (DOF) system in a piece-wise linear manner. The numerical solution of the governing differential equations following an explicit time integration scheme yields an excellent reproduction of the mechanical behaviour of the specimen, consequently confirming the accuracy of the numerical approach. However, the spring representing the accelerometer predicts a response that qualitatively matches the assumed force-displacement response of the test specimen with a perceptibly lower magnitude of load.

Evaluation of document binarization using eigen value decomposition

A necessary step for the recognition of scanned documents is binarization, which is essentially the segmentation of the document. In order to binarize a scanned document, we can find several algorithms in the literature. What is the best binarization result for a given document image? To answer this question, a user needs to check different binarization algorithms for suitability, since different algorithms may work better for different type of documents. Manually choosing the best from a set of binarized documents is time consuming. To automate the selection of the best segmented document, either we need to use ground-truth of the document or propose an evaluation metric. If ground-truth is available, then precision and recall can be used to choose the best binarized document. What is the case, when ground-truth is not available? Can we come up with a metric which evaluates these binarized documents? Hence, we propose a metric to evaluate binarized document images using eigen value decomposition. We have evaluated this measure on DIBCO and H-DIBCO datasets. The proposed method chooses the best binarized document that is close to the ground-truth of the document.

Evaluation of the accuracy of an impact load cell using lumped parameter modeling and analysis

The objective of the current study is to evaluate the fidelity of load cell reading during impact testing in a drop-weight impactor using lumped parameter modeling. For the most common configuration of a moving impactor-load cell system in which dynamic load is transferred from the impactor head to the load cell, a quantitative assessment is made of the possible discrepancy that can result in load cell response. A 3-DOF (degrees-of-freedom) LPM (lumped parameter model) is considered to represent a given impact testing set-up. In this model, a test specimen in the form of a steel hat section similar to front rails of cars is represented by a nonlinear spring while the load cell is assumed to behave in a linear manner due to its high stiffness. Assuming a given load-displacement response obtained in an actual test as the true behavior of the specimen, the numerical solution of the governing differential equations following an implicit time integration scheme is shown to yield an excellent reproduction of the mechanical behavior of the specimen thereby confirming the accuracy of the numerical approach. The spring representing the load cell, however,predicts a response that qualitatively matches the assumed load-displacement response of the test specimen with a perceptibly lower magnitude of load.

Evaluation of the accuracy of an accelerometer response generated by axial impact loading

The basic objective in the present study is to show that for the most common configuration of an impactor system, an accelerometer cannot exactly reproduce the dynamic response of a specimen subject to impact loading. Assessment of the accelerometer mounted in a drop-weight impactor setup for an axially loaded specimen is done with the aid of an equivalent lumped parameter model (LPM) of the setup. A steel hat-type specimen under the impact loading is represented as a non-linear spring of varying stiffness, while the accelerometer is assumed to behave in a linear manner due to its high stiffness. A suitable numerical approach has been used to solve the non-linear governing equations for a 3 degrees-of-freedom system in a piece-wise linear manner. The numerical solution following an explicit time integration scheme is used to yield an excellent reproduction of the mechanical behavior of the specimen thereby confirming the accuracy of the numerical approach. The spring representing the accelerometer, however, predicts a response that qualitatively matches the assumed load–displacement response of the test specimen with a perceptibly lower magnitude of load.

Development and Evaluation of Statistical Downscaling Models for Monthly Precipitation

Several statistical downscaling models have been developed in the past couple of decades to assess the hydrologic impacts of climate change by projecting the station-scale hydrological variables from large-scale atmospheric variables simulated by general circulation models (GCMs). This paper presents and compares different statistical downscaling models that use multiple linear regression (MLR), positive coefficient regression (PCR), stepwise regression (SR), and support vector machine (SVM) techniques for estimating monthly rainfall amounts in the state of Florida. Mean sea level pressure, air temperature, geopotential height, specific humidity, U wind, and V wind are used as the explanatory variables/predictors in the downscaling models. Data for these variables are obtained from the National Centers for Environmental Prediction-National Center for Atmospheric Research (NCEP-NCAR) reanalysis dataset and the Canadian Centre for Climate Modelling and Analysis (CCCma) Coupled Global Climate Model, version 3 (CGCM3) GCM simulations. The principal component analysis (PCA) and fuzzy c-means clustering method (FCM) are used as part of downscaling model to reduce the dimensionality of the dataset and identify the clusters in the data, respectively. Evaluation of the performances of the models using different error and statistical measures indicates that the SVM-based model performed better than all the other models in reproducing most monthly rainfall statistics at 18 sites. Output from the third-generation CGCM3 GCM for the A1B scenario was used for future projections. For the projection period 2001-10, MLR was used to relate variables at the GCM and NCEP grid scales. Use of MLR in linking the predictor variables at the GCM and NCEP grid scales yielded better reproduction of monthly rainfall statistics at most of the stations (12 out of 18) compared to those by spatial interpolation technique used in earlier studies.

Validation of component assembly model and extension to plasticity

Material potential energy is well approximated by '' pair-functional '' potentials. During calculating potential energy, the orientational and volumetric components have been derived from pair potentials and embedding energy, respectively. Slip results in plastic deformation, and slip component has been proposed accordingly. Material is treated as a component assembly, and its elastic, plastic and damage properties are reflected by different components respectively. Material constitutive relations are formed by means of assembling these three kinds of components. Anisotropy has been incorporated intrinsically via the concept of component. Theoretical and numerical results indicate that this method has the capacity of reproducing some results satisfactorily, with the advantages of physical explicitness, etc. (c) 2007 Elsevier Ltd. All rights reserved.

Numerical-simulation of low supersonic-flow around a sphere

The controlled equations defined in a physical plane are changed into those in a computational plane with coordinate transformations suitable for different Mach number M(infinity). The computational area is limited in the body surface and in the vicinities of detached shock wave and sonic line. Thus the area can be greatly cut down when the shock wave moves away from the body surface as M(infinity) --> 1. Highly accurate, total variation diminishing (TVD) finite-difference schemes are used to calculate the low supersonic flowfield around a sphere. The stand-off distance, location of sonic line, etc. are well comparable with experimental data. The long pending problem concerning a flow passing a sphere at 1.3 greater-than-or-equal-to M(infinity) > 1 has been settled, and some new results on M(infinity) = 1.05 have been presented.

Conceptual model of salt marsh management on Merritt Island National Wildlife Refuge, Florida: final report

Diking and holding water on salt marshes ("impounding" the marsh) is a management technique used on Merritt Island National Wildlife Refuge (MINWR) and elsewhere in the Southeast to: a) prevent the reproduction of saltmarsh mosquitos, and b) attract wintertering waterfowl and other marsh, shore, and wading birds. Because of concern that diking and holding water may interfere with the production of estuarine fish and shellfish, impoundment managers are being asked to consider altering management protocol to reduce or eliminate any such negative influence. How to change protocol and preserve effective mosquito control and wildlife management is a decision of great complexity because: a) the relationships between estuarine organisms and the fringing salt marshes at the land-water interface are complex, and b) impounded marshes are currently good habitat for a variety of species of fish and wildlife. Most data collection by scientists and managers in the area has not been focused on this particular problem. Furthermore, collection of needed data may not be possible before changes in protocol are demanded. Therefore, the purpose of this document is two-fold: 1) to suggest management alternatives, given existing information, and 2) to help identify research needs that have a high probability of leading to improved simultaneous management of mosquitos, waterfowl, other wildlife, freshwater fish, and estuarine fish and shellfish on the marshland of the Merritt Island National Wildlife Refuge. (92 page document)

Statistics of Turbulence in Benthal Boundary Layers

This paper deals with turbulence behavior inbenthalboundarylayers by means of large eddy simulation (LES). The flow is modeled by moving an infinite plate in an otherwise quiescent water with an oscillatory and a steady velocity components. The oscillatory one aims to simulate wave effect on the flow. A number of large-scale turbulence databases have been established, based on which we have obtained turbulencestatisticsof the boundarylayers, such as Reynolds stress, turbulence intensity, skewness and flatness ofturbulence, and temporal and spatial scales of turbulent bursts, etc. Particular attention is paid to the dependences of those statistics on two nondimensional parameters, namely the Reynolds number and the current-wave velocity ratio defined as the steady current velocity over the oscillatory velocity amplitude. It is found that the Reynolds stress and turbulence intensity profile differently from phase to phase, and exhibit two types of distributions in an oscillatory cycle. One is monotonic occurring during the time when current and wave-induced components are in the same direction, and the other inflectional occurring during the time when current and wave-induced components are in opposite directions. Current component makes an asymmetrical time series of Reynolds stress, as well as turbulence intensity, although the mean velocity series is symmetrical as a sine/cosine function. The skewness and flatness variations suggest that the turbulence distribution is not a normal function but approaches to a normal one with the increasing of Reynolds number and the current-wave velocity ratio as well. As for turbulent bursting, the dimensionless period and the mean area of all bursts per unit bed area tend to increase with Reynolds number and current-wave velocity ratio, rather than being constant as in steady channel flows.

Destruction of Chemical Agents in a Plasma Reactor with Working Gas of Hydrogen

The Effects of Salinity, Temperature, and Food on the Growth and Reproductive Output of Polydora nuchalis Woodick, 1953

Polydora nuchalis Woodwick, 1953 (Polychaeta: Spionidae) is a protandric hermaphrodite commonly inhabiting intertidal mud flats in southern California. The species exhibits lecithotrophic larval development and adelphophagia. Reproduction of P. nuchalis was monitored for a year at four sites: Catalina Harbor, San Gabriel River, Huntington Harbour, and Malibu Lagoon. Females deposited from 11 to 31 egg capsules in their tubes, with up to 230 eggs per capsule. An average of 3% of the eggs developed into larvae: the remaining were nurse eggs serving as food for the developing larvae. Reproductive output was quantified by determining the number and size of larvae and nurse eggs for individual capsules. Significant differences among the four populations were found for all the quantified variables. In addition, two size classes of nurse eggs were found to exist in capsules from all of the sites. Egg capsules were found throughout the year at San Gabriel River, but none were found during the winter months at the remaining three sites. Size/frequency data for juveniles and adults of the Catalina Harbor population indicate an annual cycle of recruitment. The laboratory experiment consisted of a 3 x 3 x 2 £actor1al design with replication testing the effects of temperature, salinity, and food supply on growth and reproduction of P. nuchalis. Increasing temperature resulted in significantly increased survivorship, growth rates, and percentage reproduction. It also produced a significant decrease in the size of the nurse eggs and the volume of food per larva. The number of egg capsules was maximum at the intermediate temperature. Increasing the salinity resulted in significant increases in survivorship and Class I nurse egg size. Increaaing food availability produced a significant increase in the percentage of worms reproducing. The interactive effect of salinity and £ood level produced significant changes in the number of larvae per capsule and the number of nurse eggs per capsule. However, the number of nurse eggs per larva did not differ significantly among the experimental treatment groups. (PDF contains 129 pages)

Underwater Passive Acoustic Monitoring for Remote Regions, Hawaii Institute of Marine Biology, Coconut Island, Hawaii, February 7-9, 2007: workshop proceedings

The Alliance for Coastal Technologies (ACT) convened a workshop, sponsored by the Hawaii-Pacific and Alaska Regional Partners, entitled Underwater Passive Acoustic Monitoring for Remote Regions at the Hawaii Institute of Marine Biology from February 7-9, 2007. The workshop was designed to summarize existing passive acoustic technologies and their uses, as well as to make strategic recommendations for future development and collaborative programs that use passive acoustic tools for scientific investigation and resource management. The workshop was attended by 29 people representing three sectors: research scientists, resource managers, and technology developers. The majority of passive acoustic tools are being developed by individual scientists for specific applications and few tools are available commercially. Most scientists are developing hydrophone-based systems to listen for species-specific information on fish or cetaceans; a few scientists are listening for biological indicators of ecosystem health. Resource managers are interested in passive acoustics primarily for vessel detection in remote protected areas and secondarily to obtain biological and ecological information. The military has been monitoring with hydrophones for decades;however, data and signal processing software has not been readily available to the scientific community, and future collaboration is greatly needed. The challenges that impede future development of passive acoustics are surmountable with greater collaboration. Hardware exists and is accessible; the limits are in the software and in the interpretation of sounds and their correlation with ecological events. Collaboration with the military and the private companies it contracts will assist scientists and managers with obtaining and developing software and data analysis tools. Collaborative proposals among scientists to receive larger pools of money for exploratory acoustic science will further develop the ability to correlate noise with ecological activities. The existing technologies and data analysis are adequate to meet resource managers' needs for vessel detection. However, collaboration is needed among resource managers to prepare large-scale programs that include centralized processing in an effort to address the lack of local capacity within management agencies to analyze and interpret the data. Workshop participants suggested that ACT might facilitate such collaborations through its website and by providing recommendations to key agencies and programs, such as DOD, NOAA, and I00s. There is a need to standardize data formats and archive acoustic environmental data at the national and international levels. Specifically, there is a need for local training and primers for public education, as well as by pilot demonstration projects, perhaps in conjunction with National Marine Sanctuaries. Passive acoustic technologies should be implemented immediately to address vessel monitoring needs. Ecological and health monitoring applications should be developed as vessel monitoring programs provide additional data and opportunities for more exploratory research. Passive acoustic monitoring should also be correlated with water quality monitoring to ease integration into long-term monitoring programs, such as the ocean observing systems. [PDF contains 52 pages]

Commercial mariculture of Oreochromis niloticus using net cages

The culture of tilapia has a long history in Africa. Fossil remains of members of the genus have been found which are about 18 million years old (Fryer and Iles, 1972). Oreochromis niloticus was the subject of detailed observations in Egypt of 5,000 years ago. A bas relief of 2,500B.C. depicts tilapia being reared in ponds in Egypt. However, despite this long history the prolific nature of this fish results in very high populations in pond culture systems. Consequently small size fish are harvested. Several methods have thus been tried to control the excessive reproduction of tilapia in captivity with only partial success. This paper reports how large size tilapia especially O. niloticus averaging at least 150g per piece can be commercially produced using floating net cages in the marine environment

Observations on the ecology of Hepsetus odoe, Bloch, 1794 (Pisces: Hepsetidae) in Epie Creek floodplain, Niger Delta, Nigeria

The distribution, abundance, age and growth, the food and feeding habits, condition factor and reproduction of Hepsetus odoe in the Epie Creek Floodplain (Nigeria) was studied. H. odoe occur in the creek, swamp channel and lake. It is a very common, abundant and one of the major commercial species. A total of 457 specimens weighing 76.90 kg were caught during the period of investigation. The catches were more abundant in the dry season than in the wet season. The total length ranged from 10 cm to 46 cm while the weight varied between 50 g and 900 g. Six distinct components or year classes were observed using Bhattacharya's method. A growth exponential value 'b' was 3.35 with condition factor, 'k' values ranging from 0.69 to 0.83. The main diets of Hepsetus odoe were fish, including crustaceans (shrimps) and insects. The mean fecundity was 6060 plus or minus 358 eggs (range 2,769 to 6.667 eggs). The ova diameter of H. odoe was found to range from 2.2 mm to 2.6 mm with overall mean = 2.4 plus or minus 0.1)