Mathematical Model and Simulation of a Pneumatic Apparatus for In-Drilling Alignment of an Inertial Navigation Unit during Horizontal Well Drilling

Conventional methods in horizontal drilling processes incorporate magnetic surveying techniques for determining the position and orientation of the bottom-hole assembly (BHA). Such means result in an increased weight of the drilling assembly, higher cost due to the use of non-magnetic collars necessary for the shielding of the magnetometers, and significant errors in the position of the drilling bit. A fiber-optic gyroscope (FOG) based inertial navigation system (INS) has been proposed as an alternative to magnetometer -based downhole surveying. The utilizing of a tactical-grade FOG based surveying system in the harsh downhole environment has been shown to be theoretically feasible, yielding a significant BHA position error reduction (less than 100m over a 2-h experiment). To limit the growing errors of the INS, an in-drilling alignment (IDA) method for the INS has been proposed. This article aims at describing a simple, pneumatics-based design of the IDA apparatus and its implementation downhole. A mathematical model of the setup is developed and tested with Bloodshed Dev-C++. The simulations demonstrate a simple, low cost and feasible IDA apparatus.

A comparison of in situ constant and falling head permeameter tests to assess the distribution of clogging within horizontal subsurface flow constructed wetlands

Clogging is the main operational problem associated with horizontal subsurface flow constructed wetlands (HSSF CWs). The measurement of saturated hydraulic conductivity has proven to be a suitable technique to assess clogging within HSSF CWs. The vertical and horizontal distribution of hydraulic conductivity was assessed in two full-scale HSSF CWs by using two different in situ permeameter methods (falling head (FH) and constant head (CH) methods). Horizontal hydraulic conductivity profiles showed that both methods are correlated by a power function (FH= CH 0.7821, r 2=0.76) within the recorded range of hydraulic conductivities (0-70 m/day). However, the FH method provided lower values of hydraulic conductivity than the CH method (one to three times lower). Despite discrepancies between the magnitudes of reported readings, the relative distribution of clogging obtained via both methods was similar. Therefore, both methods are useful when exploring the general distribution of clogging and, specially, the assessment of clogged areas originated from preferential flow paths within full-scale HSSF CWs. Discrepancy between methods (either in magnitude and pattern) aroused from the vertical hydraulic conductivity profiles under highly clogged conditions. It is believed this can be attributed to procedural differences between the methods, such as the method of permeameter insertion (twisting versus hammering). Results from both methods suggest that clogging develops along the shortest distance between water input and output. Results also evidence that the design and maintenance of inlet distributors and outlet collectors appear to have a great influence on the pattern of clogging, and hence the asset lifetime of HSSF CWs. © Springer Science+Business Media B.V. 2011.

A finite element approach to modelling the hydrological regime in horizontal subsurface flow constructed wetlands for wastewater treatment

A Finite Element Analysis (FEA) model is used to explore the relationship between clogging and hydraulics that occurs in Horizontal Subsurface Flow Treatment Wetlands (HSSF TWs) in the United Kingdom (UK). Clogging is assumed to be caused by particle transport and an existing single collector efficiency model is implemented to describe this behaviour. The flow model was validated against HSSF TW survey results obtained from the literature. The model successfully simulated the influence of overland flow on hydrodynamics, and the interaction between vertical flow through the low permeability surface layer and the horizontal flow of the saturated water table. The clogging model described the development of clogging within the system but under-predicted the extent of clogging which occurred over 15 years. This is because important clogging mechanisms were not considered by the model, such as biomass growth and vegetation establishment. The model showed the usefulness of FEA for linking hydraulic and clogging phenomenon in HSSF TWs and could be extended to include treatment processes. © 2011 Springer Science+Business Media B.V.

On the role of surface roughness in the aerodynamic performance and energy conversion of horizontal wind turbine blades:a review

Summary: Renewable energy is one of the main pillars of sustainable development, especially in developing economies. Increasing energy demand and the limitation of fossil fuel reserves make the use of renewable energy essential for sustainable development. Wind energy is considered to be one of the most important resources of renewable energy. In North African countries, such as Egypt, wind energy has an enormous potential; however, it faces quite a number of technical challenges related to the performance of wind turbines in the Saharan environment. Seasonal sand storms affect the performance of wind turbines in many ways, one of which is increasing the wind turbine aerodynamic resistance through the increase of blade surface roughness. The power loss because of blade surface deterioration is significant in wind turbines. The surface roughness of wind turbine blades deteriorates because of several environmental conditions such as ice or sand. This paper is the first review on the topic of surface roughness effects on the performance of horizontal-axis wind turbines. The review covers the numerical simulation and experimental studies as well as discussing the present research trends to develop a roadmap for better understanding and improvement of wind turbine performance in deleterious environments.

A horizontális és vertikális ágazaton belüli agrárkereskedelem meghatározó tényezői az EU új tagországaiban (Determinants of horizontal and vertical intra-industry agri-food trade in the new EU member-states)

Az ágazaton belüli kereskedelem egyre komolyabb szerepet tölt be a nemzetközi kereskedelemben, mind ez idáig azonban kevés mezőgazdasági témájú elemzés készült e témában. A cikk célja a horizontális és vertikális ágazaton belüli agrárkereskedelem meghatározó tényezőinek azonosítása az új tagországok és az EU–27 közötti kereskedelemben 1999–2010 között. Ehhez a szerző statikus és dinamikus panelmódszereket alkalmaz különböző specifikációkkal. Eredményei szerint a tényezőellátottság a horizontális ágazaton belüli kereskedelemmel negatív, míg a vertikálissal pozitív kapcsolatban áll. Az országok mérete az ágazaton belüli kereskedelem mindkét oldalával pozitívan, míg a távolság negatívan korrelál. Az eredmények azt is kimutatják, hogy az ágazaton belüli kereskedelem mértéke nagyobb, ha egy új tagország a kelet-közép-európai régióba exportál, és az is világossá vált, hogy az EU-csatlakozás pozitívan hatott az ágazaton belüli kereskedelemre, jelezve a gazdasági integráció kereskedelemösztönző szerepét. _____ Intra-industry trade (IIT) has a growing role in international trade, although the number of papers on its agricultural aspects is limited. This article identifies the determinants of horizontal and vertical intra-industry agri-food trade between new member-states (NMS) and the EU27 in 1999-2010, by applying to panel data static and dynamic models with different specifications. The results show that factor endowments are negatively related to agri-food horizontal intra-industry trade (HIIT), but positively to vertical intra-industry trade (VIIT). Economic size is positively and significantly related to both, while distance and IIT are found to be negatively related. This also suggests that HIIT and VIIT are greater if an NMS exports agri-food products to another NMS, while EU accession has had positive and significant impacts on both HIIT and VIIT, which suggests that economic integration fosters IIT.

Horizontal diversity of higher education institutions. The case of Hungary – in European context

In the European Higher Education Area the diversification of higher education is considered to be an emphasized value, a guarantee of creativity. The various institutional rankings are the displays of vertical diversity, but in parallel with these, there is an increasing attention directed at horizontal diversity, the entirety of the institutions' activities. The European Mapping Project (U-map) undertook this challenge. The paper presents the research program, which is an attempt to adapt the U-map model to Hungary. According to the results, the U-map method which was intended for application on an international level, is very useful in the identification of the main groups of institutions in a specific national higher education system as well, and may provide a basis for the creation of institutional strategies and the development of the institutions’ network.

Country-specific determinants of horizontal and vertical intra-industry agri-food trade: the case of Bulgaria and Romania

The article analyses patterns and country-specific determinants of agri-food trade of Bulgaria and Romania with the European Union. As literature focusing on agricultural aspects of the topic is limited, the paper seeks to contribute to the literature by providing up to date results and suggestions as well as by identifying the determinants of horizontal and vertical intra-industry trade of the Bulgaria and Romania after EU accession. Results suggest that intra-industry agri-food trade is mainly of vertical nature, referring to trade of different quality products. Results verify that determinants of horizontal and vertical IIT are similar and suggest that economic size and FDI are positively, while factor endowments and distance are negatively related to both sides of IIT. Results are mainly in line with the majority of empirical literature in the field.

Horizontal genetic transfer in asexual fungi

Four aspects of horizontal genetic transfer during heterokaryon formation were examined in the asexual pathogen Fusarium oxysporum f.sp. cubense (Foc): (1) variability based on method of heterokaryon formation; (2) differences in nuclear and mitochondrial inheritance; (3) the occurrence of recombination without nuclear fusion; (4) the occurrence of horizontal genetic transfer between distantly related isolates. The use of non-pathogenic strains of Fusarium oxysporum as biocontrol agents warrants a closer examination at the reproductive life cycle of this fungus, particularly if drug resistance or pathogenicity genes can be transmitted horizontally. Experiments were divided into three phases. Phase I looked at heterokaryon formation by hyphal anastomosis and protoplast fusion. Phase II was a time course of heterokaryon formation to look at patterns of nuclear and mitochondrial inheritance. Phase III examined the genetic relatedness of the different vegetative compatibility groups using a multilocus analysis approach. Heterokaryon formation was evident within and between vegetative compatibility groups. Observation of non-parental genotypes after heterokaryon formation confirmed that, although a rare event, horizontal genetic transfer occurred during heterokaryon formation. Uniparental mitochondria inheritance was observed in heterokaryons formed either by hyphal anastomosis or protoplast fusion. Drug resistance was expressed during heterokaryon formation, even across greater genetic distances than those distances imposed by vegetative compatibility. Phylogenies inferred from different molecular markers were incongruent at a significant level, challenging the clonal origins of Foc. Mating type genes were identified in this asexual pathogen Polymorphisms were detected within a Vegetative Compatibility Group (VCG) suggesting non-clonal inheritance and/or sexual recombination in Foc. This research was funded in part by a NIH-NIGMS (National Institutes of Health-National Institute of General Medical Sciences) Grant through the MBRS (Minority Biomedical Research Support), the Department of Biological Sciences and the Tropical Biology Program at FIU. ^

Determination of vertical and horizontal pathways of injected fresh wastewater into a deep saline aquifer (Florida, USA) using natural chemical tracers

Two deep-well injection sites in south Florida, USA, inject an average of 430 million liters per day (MLD) of treated domestic fresh wastewater into a deep saline aquifer 900 m below land surface. Elevated levels of NH3 (highest concentration 939 µmol) in the overlying aquifer above ambient concentrations (concentration less than 30 µmol) were evidence of the upward migration of injected fluids. Three pathways were distinguished based on ammonium, chloride and bromide ratios, and temperature. At the South District Wastewater Treatment Plant, the tracer ratios showed that the injectate remained chemically distinct as it migrated upwards through rapid vertical pathways via density-driven buoyancy. The warmer injectate (mean 28°C) retained the temperature signal as it vertically migrated upwards; however, the temperature signal did not persist as the injectate moved horizontally into the overlying aquifers. Once introduced, the injectate moved slowly horizontally through the aquifer and mixed with ambient water. At the North District Wastewater Treatment Plant, data provide strong evidence of a one-time pulse of injectate into the overlying aquifers due to improper well construction. No evidence of rapid vertical pathways was observed at the North District Wastewater Treatment Plant.

Fluidos de perfuração aquosos: a contribuição da goma xantana e carboximetilcelulose no controle de filtrado

This study aimed mainly to evaluate the influence of xanthan gum (XG) and carboxymethylcellulose (CMC) in the filtration process of water-based drilling fluids, considering the conformational changes suffered by the polyelectrolyte with the addition of sodium chloride (NaCl) in different concentrations (0.17, 0.34 and 0.51 mol.L-1). It was also evaluated the behavior of the fluid by the addition of calcium carbonate (CaCO3) in pure water and in brine. Seeking a better understanding of the interaction between the polymers used and CaCO3, polymer adsorption analyzes were performed using a depletion method, which yielded a higher percentage of adsorption of Xanthan Gum in this material (29%), which can justify the formation of a thin and waterproof filter cake for drilling fluids containing this polymer. However, the best values of apparent viscosity (20 and 24 mPa.s) and volume of filtrate (8.0 and 8.1 mL) were obtained for the systems consisting of xanthan gum, CMC and CaCO3, in NaCl aqueous solutions concentrations of 0.34 and 0.51 mol.L-1, respectively. The values can be related to the presence of CMC that increases the apparent viscosity and reduces the volume of filtrate. In addition, the CaCO3 added acts as a bridging agent, promoting the formation of a less permeable filter cake

Comportamento geotécnico de misturas de solo e resíduos de perfuração onshore

The drilling of wells for petroleum extraction generates rocks and soils fragments, among other residues. These fragments are denominated petroleum drilling gravel or simply petroleum drilling residue. On the sites of onshore exploration are formed big deposits of drilling gravel, an expensive final destination material. This work aims at evaluating the addition of drilling residue to a lateritic soil, as composite material, for construction of compacted fills for earth work projects. Soil and residue were evaluated by X-ray diffraction (XRD) and X-ray fluorescence (XRF) and by laboratory tests traditionally used in soil mechanics, as particle-size analysis of soils, determination of liquid and plasticity indexes and compaction test. After soil and residue characterization, soil-residue mixtures were studied, using dosages of 2,5%, 5%, 10%, and 15% of residue in relation to the dry soil mass. These mixtures were submitted to compaction test, CBR, direct shear test and consolidation test. The test results were compared to the current legislation of DNIT for compacted fill construction. The results showed that the mixtures presented the minimal necessary parameters, allowing, from the point of view of geotechnical analysis, the use of these mixtures for construction of compacted fills

Avaliação de compatibilidade entre pasta de cimento e fluido de perfuração não-aquoso utilizados em poços petrolíferos

Compatibility testing between a drilling fluid and a cement slurry is one of the steps before an operation of cementing oil wells. This test allows us to evaluate the main effects that contamination of these two fluids may cause the technological properties of a cement paste. The interactions between cement paste and drilling fluid, because its different chemical compositions, may affect the cement hydration reactions, damaging the cementing operation. Thus, we carried out the study of the compatibility of non-aqueous drilling fluid and a cement slurry additives. The preparation procedures of the non-aqueous drilling fluid, the cement paste and completion of compatibility testing were performed as set out by the oil industry standards. In the compatibility test is evaluated rheological properties, thickening time, stability and compressive strength of cement pastes. We also conducted analyzes of scanning electron microscopy and X-ray diffraction of the mixture obtained by the compatibility test to determine the microstructural changes in cement pastes. The compatibility test showed no visual changes in the properties of the cement paste, as phase separation. However, after the addition of nonaqueous drilling fluid to cement slurry there was an increased amount of plastic viscosity, the yield point and gel strength. Among the major causative factors can include: chemical reaction of the components present in the non-aqueous drilling fluid as the primary emulsifier, wetting agent and paraffin oil, with the chemical constituents of the cement. There was a reduction in the compressive strength of the cement paste after mixing with this drilling fluid. Thickening test showed that the oil wetting agent and high salinity of the non-aqueous fluid have accelerating action of the handle of the cement paste time. The stability of the cement paste is impaired to the extent that there is increased contamination of the cement slurry with the nonaqueous fluid. The X-ray diffraction identified the formation of portlandite and calcium silicate in contaminated samples. The scanning electron microscopy confirmed the development of the identified structures in the X-ray diffraction and also found the presence of wells in the cured cement paste. The latter, formed by the emulsion stability of the drilling fluid in the cement paste, corroborate the reduction of mechanical strength. The oil wetting agent component of the non-aqueous drilling fluid, the modified cement hydration processes, mainly affecting the setting time.

Estudo da incorporação de resíduos de perfuração para aplicação em cimentação de poços de petróleo

During the drilling of oil and natural gas are generated solid waste, liquid and gaseous. These solid fragments, which are known as cuttings, are carried to the surface through the drilling fluid. Furthermore, this fluid serves to cool the bit, keeping the internal pressure of the well, and others. This solid residue is very polluting, because it has incorporated beyond the drilling fluid, which has several chemical additives harmful to the environment, some heavy metals that are harmful to the environment, such as lead. To minimize the residue generated, are currently being studied numerous techniques to mitigate the problems that such waste can cause to the environment, like addition of cuttings in the composition of soil cement brick masonry construction, addition of cuttings on the clay matrix for the manufacture of solid masonry bricks and ceramic blocks and coprocessing of the cuttings in cement. So, the main objective of this work is the incorporation of cuttings drilling of oil wells, the cement slurry used in the cementing operation of the well. This cuttings used in this study, arising from the formation Pendências, was milled and separated in a sieve of 100 mesh. After grinding had a mean particle sike in order of 86 mm and crystal structure containing phases of quartz and calcite type, characteristic of the Portland cement. Were formulated and prepared slurries of cement with density 13 lb / gal, containing different concentrations of gravel, and realized characterization tests API SPEC 10A and RP 10B. Free water tests showed values lower than 5.9% and the rheological model that best described the behavior of the mixtures was the power. The results of compressive strength (10.3 MPa) and stability (Dr <0.5 lb / gal) had values within the set of operational procedures. Thus, the gravel from the drilling operation, may be used as binders in addition to Portland cement oil wells, in order to reuse this waste and reduce the cost of the cement paste.

Uso de água produzida na formulação de fluidos de perfuração

Drilling fluids have fundamental importance in the petroleum activities, since they are responsible for remove the cuttings, maintain pressure and well stability, preventing collapse and inflow of fluid into the rock formation and maintain lubrication and cooling the drill. There are basically three types of drilling fluids: water-based, non-aqueous and aerated based. The water-based drilling fluid is widely used because it is less aggressive to the environment and provide excellent stability and inhibition (when the water based drilling fluid is a inhibition fluid), among other qualities. Produced water is generated simultaneously with oil during production and has high concentrations of metals and contaminants, so it’s necessary to treat for disposal this water. The produced water from the fields of Urucu-AM and Riacho da forquilha-RN have high concentrations of contaminants, metals and salts such as calcium and magnesium, complicating their treatment and disposal. Thus, the objective was to analyze the use of synthetic produced water with similar characteristics of produced water from Urucu-AM and Riacho da Forquilha-RN for formulate a water-based drilling mud, noting the influence of varying the concentration of calcium and magnesium into filtered and rheology tests. We conducted a simple 32 factorial experimental design for statistical modeling of data. The results showed that the varying concentrations of calcium and magnesium did not influence the rheology of the fluid, where in the plastic viscosity, apparent viscosity and the initial and final gels does not varied significantly. For the filtrate tests, calcium concentration in a linear fashion influenced chloride concentration, where when we have a higher concentration of calcium we have a higher the concentration of chloride in the filtrate. For the Urucu’s produced water based fluids, volume of filtrate was observed that the calcium concentration influences quadratically, this means that high calcium concentrations interfere with the power of the inhibitors used in the formulation of the filtered fluid. For Riacho’s produced water based fluid, Calcium’s influences is linear for volume of filtrate. The magnesium concentration was significant only for chloride concentration in a quadratic way just for Urucu’s produced water based fluids. The mud with maximum concentration of magnesium (9,411g/L), but minimal concentration of calcium (0,733g/L) showed good results. Therefore, a maximum water produced by magnesium concentration of 9,411g/L and the maximum calcium concentration of 0,733g/L can be used for formulating water-based drilling fluids, providing appropriate properties for this kind of fluid.

Tratamento de cascalho de perfuração utilizando sistemas microemulsionados

The oil industry is one of the activities that generates more waste to the environment. The drill cuttings is a waste generated in large quantities in the drilling process and that may cause environmental damage such as soil contamination and consequently the contamination of groundwater if disposed of without prior treatment. Arises the need to develop scientific activities and research ways to adapt these wastes the current environmental standards. In the case of solid wastes, the NBR 10004: 2004 of the Brazilian Association of Technical Standards (ABNT) classifies them into class I waste (hazardous) and class II (not dangerous), which determines which wastes may or may not be discarded in the environment without causing environmental impact. This study presents a novel alternative for treating drill cuttings, where this waste was classified as class I (Abreu & Souza, 2005), mainly by removing the n-paraffin present in it, since this arises when using drilling fluids base oil. Using microemulsion systems promotes the removal of this contaminant drill cuttings samples from wells located in Alto do Rodrigues - RN. Initially, we determined the concentration of paraffin using infrared method in samples were extracted with ultrasound, we obtained a paraffin concentration in the range from 36.59 to 43.52 g of paraffin per kilogram of cuttings. Used two microemulsion systems containing two nonionic surfactants from different classes, one is an alcohol ethoxylated (UNTL-90) and the other an nonylphenol ethoxylated (RNX 110). The results indicated that the system UNTL-90 surfactant has better efficiency than the system with RNX 110. The study of the influence of contact time at the extraction showed that for times greater than 25 minutes has a tendency to increase the percentage extraction with increasing contact time. It was also observed that the extraction is fast because at 1 minute contact has 22.7% extraction. The reuse of the microemulsion system without removing the paraffin extracted in previous steps, showed reduction of 29.32 in percentage of extraction by comparing the first and third extraction, but by comparing the first and second extractions reduction is 8.5 in percentage extraction, so the systems reuse optimization can be an option for economically viable removing paraffin from cuttings. The extraction with shaking is more effective in the treatment of cuttings, reaching the extraction percentage of 87.04%, that is, obtaining a drill cuttings with 0.551% paraffin. Using the percentage of paraffin employed in non-aqueous drilling fluids and fluid maximum limit on cuttings for disposal established by the Environmental Protection Agency of the United States (US EPA), one arrives at the conclusion that the level of paraffin on gravel cannot exceed 3.93%. Conclude that the amount of paraffin in the treated cuttings with the microemulsion system with shaking is below the established by US EPA, showing that the system used was efficient in removing the paraffin from the drill cuttings.