Aerodynamic parametric analysis of an unconventional joined-wing aircraft configuration

In this paper, the experimental results of an unconventional joined-wing aircraft configuration are presented. The test model uses two different wings, forward and rear, both joined in tandem and forming diamond shapes both in plant and front views. The wings are joined in such a way that it is possible to change the rear wing dihedral angle values and the rear wing sweep angle values in 25 different positions that modify the relative distance and the relative height between the wings. To measure the system aerodynamic coefficients itis necessary to perform wind tunnel tests. The datapresented corresponds to the lift, drag and induced drag aerodynamic coefficients, as well as the aerodynamic efficiency and the parameter for minimum required power, from the calculated values of the lift and drag time series measured by a 6-axis force and torque sensor. The results show the influence on the aerodynamic coefficients of the rear wing sweep and dihedral angles parameters. As a main result, it can be concluded that, in general terms, the lift and induced drag aerodynamic coefficients values decrease as both the distance and height between the wings increase, on the other hand, the total drag aerodynamic coefficient decreases if the distance between the wings increases, but nevertheless shows a slight tendency to increase if the height of the rear wing increases, whereas the aerodynamic efficiency and the parameter for minimum required power increase if the distance between the wings increases

Distance and overcurrent relay coordination considering non standardized inverse time curves

Protective relaying comprehends several procedures and techniques focused on maintaining the power system working safely during and after undesired and abnormal network conditions, mostly caused by faulty events. Overcurrent relay is one of the oldest protective relays, its operation principle is straightforward: when the measured current is greater than a specified magnitude the protection trips; less variables are required from the system in comparison with other protections, causing the overcurrent relay to be the simplest and also the most difficult protection to coordinate; its simplicity is reflected in low implementation, operation, and maintenance cost. The counterpart consists in the increased tripping times offered by this kind of relays mostly before faults located far from their location; this problem can be particularly accentuated when standardized inverse-time curves are used or when only maximum faults are considered to carry out relay coordination. These limitations have caused overcurrent relay to be slowly relegated and replaced by more sophisticated protection principles, it is still widely applied in subtransmission, distribution, and industrial systems. In this work, the use of non standardized inverse-time curves, the model and implementation of optimization algorithms capable to carry out the coordination process, the use of different levels of short circuit currents, and the inclusion of distance relays to replace insensitive overcurrent ones are proposed methodologies focused on the overcurrent relay performance improvement. These techniques may transform the typical overcurrent relay into a more sophisticated one without changing its fundamental principles and advantages. Consequently a more secure and still economical alternative can be obtained, increasing its implementation area

Comparing the performance of the EQ-5D-3L and the EQ-5D-5L in young Portuguese adults

Background Some studies have reported a ceiling effect in EQ-5D-3L, especially in healthy and/or young individuals. Recently, two further levels have been included in its measurement model (EQ-5D-5L). The purposes of this study were (1) to assess the properties of the EQ-5D-5L in comparison with the standard EQ-5D-3L in a sample of young adults, (2) to foreground the importance of collecting qualitative data to confirm, validate or refine the EQ-5D questionnaire items and (3) to raise questions pertaining to the wording in these questionnaire items. Methods The data used came from a sample of respondents aged 30 or under (n = 624). They completed both versions of the EQ-5D, which were compared in terms of feasibility, level of inconsistency and ceiling effect. Agreement between the instruments was assessed using correlation coefficients and Bland-Altman plots. Known-groups validity of the EQ-5D-5L was also assessed using non-parametric tests. The discriminative properties were compared using receiver operating characteristic curves. Finally, four interviews were conducted for retrospective reports to elicit respondents’ understanding and perceptions of the format, instructions, items, and responses. Results Quantitative results show a ceiling effect reduction of 25.3 % and a high level agreement between both indices. Known-groups validity was confirmed for the EQ-5D-5L. Explorative interviews indicated ambiguity and low degree of certainty in regards to conceptualizing differences between levels moderate-slight across three dimensions. Conclusions The EQ-5D-5L performed better than the EQ-5D-3L. However, the explorative interviews demonstrated several limitations in the EQ-5D questionnaire wording and high context-dependent answers point to lack of illnesses’ experience amongst young adults.

Removal of paracetamol on biomass-derived activated carbon: Modeling the fixed bed breakthrough curves using batch adsorption experiments

The remediation of paracetamol (PA), an emerging contaminant frequently found in wastewater treatment plants, has been studied in the low concentration range (0.3–10 mg L−1) using as adsorbent a biomass-derived activated carbon. PA uptake of up to 100 mg g−1 over the activated carbon has been obtained, with the adsorption isotherms being fairly explained by the Langmuir model. The application of Reichemberg and the Vermeulen equations to the batch kinetics experiments allowed estimating homogeneous and heterogeneous diffusion coefficients, reflecting the dependence of diffusion with the surface coverage of PA. A series of rapid small-scale column tests were carried out to determine the breakthrough curves under different operational conditions (temperature, PA concentration, flow rate, bed length). The suitability of the proposed adsorbent for the remediation of PA in fixed-bed adsorption was proven by the high PA adsorption capacity along with the fast adsorption and the reduced height of the mass transfer zone of the columns. We have demonstrated that, thanks to the use of the heterogeneous diffusion coefficient, the proposed mathematical approach for the numerical solution to the mass balance of the column provides a reliable description of the breakthrough profiles and the design parameters, being much more accurate than models based in the classical linear driving force.

PARAMETRIC STUDY OF REAXFF SIMULATION PARAMETERS FOR MOLECULAR DYNAMICS MODELING OF REACTIVE CARBON GASES

Abstract The development of innovative carbon-based materials can be greatly facilitated by molecular modeling techniques. Although the Reax Force Field (ReaxFF) can be used to simulate the chemical behavior of carbon-based systems, the simulation settings required for accurate predictions have not been fully explored. Using the ReaxFF, molecular dynamics (MD) simulations are used to simulate the chemical behavior of pure carbon and hydrocarbon reactive gases that are involved in the formation of carbon structures such as graphite, buckyballs, amorphous carbon, and carbon nanotubes. It is determined that the maximum simulation time step that can be used in MD simulations with the ReaxFF is dependent on the simulated temperature and selected parameter set, as are the predicted reaction rates. It is also determined that different carbon-based reactive gases react at different rates, and that the predicted equilibrium structures are generally the same for the different ReaxFF parameter sets, except in the case of the predicted formation of large graphitic structures with the Chenoweth parameter set under specific conditions.

A computational model of hydrogen production by steam reforming of dimethyl ether in a large scale CFB reactor. Part II:parametric analysis

This study presents a computational parametric analysis of DME steam reforming in a large scale Circulating Fluidized Bed (CFB) reactor. The Computational Fluid Dynamic (CFD) model used, which is based on Eulerian-Eulerian dispersed flow, has been developed and validated in Part I of this study [1]. The effect of the reactor inlet configuration, gas residence time, inlet temperature and steam to DME ratio on the overall reactor performance and products have all been investigated. The results have shown that the use of double sided solid feeding system remarkable improvement in the flow uniformity, but with limited effect on the reactions and products. The temperature has been found to play a dominant role in increasing the DME conversion and the hydrogen yield. According to the parametric analysis, it is recommended to run the CFB reactor at around 300 °C inlet temperature, 5.5 steam to DME molar ratio, 4 s gas residence time and 37,104 ml gcat -1 h-1 space velocity. At these conditions, the DME conversion and hydrogen molar concentration in the product gas were both found to be around 80%.

E-polynomial of SL(2,C)-character varieties of complex curves of genus 3.

We compute the E-polynomials of the moduli spaces of representations of the fundamental group of a complex curve of genus g = 3 into SL(2, C), and also of the moduli space of twisted representations. The case of genus g = 1, 2 has already been done in [12]. We follow the geometric technique introduced in [12], based on stratifying the space of representations, and on the analysis of the behaviour of the E-polynomial under fibrations.

Centile curves and reference values for height, body mass, body mass index and waist circumference of peruvian children and adolescents

This study aimed to provide height, body mass, BMI and waist circumference (WC) growth centile charts for school-children, aged 4–17 years, from central Peru, and to compare Peruvian data with North-American and Argentinean references. The sample consisted of 8753 children and adolescents (4130 boys and 4623 girls) aged 4 to 17 years, from four Peruvian cities: Barranco, La Merced, San Ramón and Junín. Height, body mass and WC were measured according to standardized techniques. Centile curves for height, body mass, BMI and WC were obtained separately for boys and girls using the LMS method. Student t-tests were used to compare mean values. Overall boys have higher median heights than girls, and the 50th percentile for body mass increases curvilinearly from 4 years of age onwards. In boys, the BMI and WC 50th percentiles increase linearly and in girls, the increase presents a curvilinear pattern. Peruvian children are shorter, lighter and have higher BMI than their counterparts in the U.S. and Argentina; in contrast, age and sex-specific WC values are lower. Height, body mass and WC of Peruvian children increased with age and variability was higher at older ages. The growth patterns for height, body mass, BMI and WC among Peruvian children were similar to those observed in North-American and Argentinean peers.

Learning curves: analysing pace and challenge in four successful puzzle games

The pace at which challenges are introduced in a game has long been identified as a key determinant of both the enjoyment and difficulty experienced by game players, and their ability to learn from game play. In order to understand how to best pace challenges in games, there is great value in analysing games already demonstrated as highly engaging. Play-through videos of four puzzle games (Portal, Portal 2 Co-operative mode, Braid and Lemmings), were observed and analysed using metrics derived from a behavioural psychology understanding of how people solve problems. Findings suggest that; 1) the main skills learned in each game are introduced separately, 2) through simple puzzles that require only basic performance of that skill, 3) the player has the opportunity to practice and integrate that skill with previously learned skills, and 4) puzzles increase in complexity until the next new skill is introduced. These data provide practical guidance for designers, support contemporary thinking on the design of learning structures in games, and suggest future directions for empirical research.

An alternative methodology for fitting selectivity curves to pre-defined distributions

A non-linear least-squares methodology for simultaneously estimating parameters of selectivity curves with a pre-defined functional form, across size classes and mesh sizes, using catch size frequency distributions, was developed based on the model of Kirkwood and Walker [Kirkwood, G.P., Walker, T.L, 1986. Gill net selectivities for gummy shark, Mustelus antarcticus Gunther, taken in south-eastern Australian waters. Aust. J. Mar. Freshw. Res. 37, 689-697] and [Wulff, A., 1986. Mathematical model for selectivity of gill nets. Arch. Fish Wiss. 37, 101-106]. Observed catches of fish of size class I in mesh m are modeled as a function of the estimated numbers of fish of that size class in the population and the corresponding selectivities. A comparison was made with the maximum likelihood methodology of [Kirkwood, G.P., Walker, T.I., 1986. Gill net selectivities for gummy shark, Mustelus antarcticus Gunther, taken in south-eastern Australian waters. Aust. J. Mar. Freshw. Res. 37, 689-697] and [Wulff, A., 1986. Mathematical model for selectivity of gill nets. Arch. Fish Wiss; 37, 101-106], using simulated catch data with known selectivity curve parameters, and two published data sets. The estimated parameters and selectivity curves were generally consistent for both methods, with smaller standard errors for parameters estimated by non-linear least-squares. The proposed methodology is a useful and accessible alternative which can be used to model selectivity in situations where the parameters of a pre-defined model can be assumed to be functions of gear size; facilitating statistical evaluation of different models and of goodness of fit. (C) 1998 Elsevier Science B.V.

Centile curves and reference values for height, body mass, body mass index and waist circumference of peruvian children and adolescents

This study aimed to provide height, body mass, BMI and waist circumference (WC) growth centile charts for school-children, aged 4–17 years, from central Peru, and to compare Peruvian data with North-American and Argentinean references. The sample consisted of 8753 children and adolescents (4130 boys and 4623 girls) aged 4 to 17 years, from four Peruvian cities: Barranco, La Merced, San Ramón and Junín. Height, body mass and WC were measured according to standardized techniques. Centile curves for height, body mass, BMI and WC were obtained separately for boys and girls using the LMS method. Student t-tests were used to compare mean values. Overall boys have higher median heights than girls, and the 50th percentile for body mass increases curvilinearly from 4 years of age onwards. In boys, the BMI and WC 50th percentiles increase linearly and in girls, the increase presents a curvilinear pattern. Peruvian children are shorter, lighter and have higher BMI than their counterparts in the U.S. and Argentina; in contrast, age and sex-specific WC values are lower. Height, body mass and WC of Peruvian children increased with age and variability was higher at older ages. The growth patterns for height, body mass, BMI and WC among Peruvian children were similar to those observed in North-American and Argentinean peers.

Maturation curves of sweet sorghum genotypes.

O sorgo sacarino [Sorghum bicolor (L.) Moench] se destaca como cultura complementar à cana-de-açúcar Saccharum spp. na produção de etanol, uma vez que este possui colmos suculentos com presença de açúcares diretamente fermentescíveis. Em decorrência deste fato, existe a necessidade de se analisar as propriedades do sorgo, a fim de atender às demandas da agroindústria. No presente trabalho, buscou-se desenvolver e estudar as curvas de maturação de sete cultivares de sorgo sacarino em dez épocas de colheita. Os resultados mostram que houve diferença significativa para cultivares e épocas de colheita para todos os parâmetros (p≤0,01). Quanto aos teores de açúcares, as cultivares BRS508, XBWS80147 e CMSXS629 apresentaram as maiores médias para as variáveis açúcares redutores totais (ART) e açúcares totais recuperáveis (ATR). Em relação à produção de etanol por tonelada de biomassa, as cultivares BRS 508 e a CMSXS629 apresentaram os melhores resultados.

Advanced numerical modeling of masonry vaulted structures based on BIM parametric geometry generation

Vaults are an architectural element which during construction history have been built with a great variety of different materials, shapes, and sizes. The shape of these structural elements was often dependent by the necessity to cover complex spaces, by the needed loading capacity, or by architectural aesthetics. Within this complex scenario masonry patterns generates also different effects on loading capacity, load percolation and stiffness of the structure. These effects were been extensively investigated, both with empirical observations and with modern numerical methods. While most of them focus on analyzing the load bearing capacity or the texture effect on vaulted structures, the aim of this analysis is to investigate on the effects of the variation of a single structural characteristic on the load percolation in the vault. Moreover, an additional purpose of the work is related to the coding of a parametrical model aiming at generating different masonry vaulted structures. Nevertheless, proposed script can generate different typology of vaulted structure basing on some structural characteristics, such as the span and the length to cover and the dimensions of the blocks.

The Hitchin map for one-nodal base curves of compact type

Studying moduli spaces of semistable Higgs bundles (E, \phi) of rank n on a smooth curve C, a key role is played by the spectral curve X (Hitchin), because an important result by Beauville-Narasimhan-Ramanan allows us to study isomorphism classes of such Higgs bundles in terms of isomorphism classes of rank-1 torsion-free sheaves on X. This way, the generic fibre of the Hitchin map, which associates to any semistable Higgs bundle the coefficients of the characteristic polynomial of \phi, is isomorphic to the Jacobian of X. Focusing on rank-2 Higgs data, this construction was extended by Barik to the case in which the curve C is reducible, one-nodal, having two smooth components. Such curve is called of compact type because its Picard group is compact. In this work, we describe and clarify the main points of the construction by Barik and we give examples, especially concerning generic fibres of the Hitchin map. Referring to Hausel-Pauly, we consider the case of SL(2,C)-Higgs bundles on a smooth base curve, which are such that the generic fibre of the Hitchin map is a subvariety of the Jacobian of X, the Prym variety. We recall the description of special loci, called endoscopic loci, such that the associated Prym variety is not connected. Then, letting G be an affine reductive group having underlying Lie algebra so(4,C), we consider G-Higgs bundles on a smooth base curve. Starting from the construction by Bradlow-Schaposnik, we discuss the associated endoscopic loci. By adapting these studies to a one-nodal base curve of compact type, we describe the fibre of the SL(2,C)-Hitchin map and of the G-Hitchin map, together with endoscopic loci. In the Appendix, we give an interpretation of generic spectral curves in terms of families of double covers.

Nonlinear modelling of non-structural masonry walls under a low-intensity earthquake motion: calibration through a parametric study

This thesis aims to understand the behavior of a low-rise unreinforced masonry building (URM), the typical residential house in the Netherlands, when subjected to low-intensity earthquakes. In fact, in the last decades, the Groningen region was hit by several shallow earthquakes caused by the extraction of natural gas. In particular, the focus is addressed to the internal non-structural walls and to their interaction with the structural parts of the building. A simple and cost-efficient 2D FEM model is developed, focused on the interfaces representing mortar layers that are present between the non-structural walls and the rest of the structure. As a reference for geometries and materials, it has been taken into consideration a prototype that was built in full-scale at the EUCENTRE laboratory of Pavia (Italy). Firstly, a quasi-static analysis is performed by gradually applying a prescribed displacement on the roof floor of the structure. Sensitivity analyses are conducted on some key parameters characterizing mortar. This analysis allows for the calibration of their values and the evaluation of the reliability of the model. Successively, a transient analysis is performed to effectively subject the model to a seismic action and hence also evaluate the mechanical response of the building over time. Moreover, it was possible to compare the results of this analysis with the displacements recorded in the experimental tests by creating a model representing the entire considered structure. As a result, some conditions for the model calibration are defined. The reliability of the model is then confirmed by both the reasonable results obtained from the sensitivity analysis and the compatibility of the values obtained for the top displacement of the roof floor of the experimental test, and the same value acquired from the structural model.