Tidal impacts on riparian salinities near estuaries

Groundwater-dependent riparian biota is known to be sensitive to changes in soil and groundwater salinity in estuarine systems. The groundwater flow and salinity behaviour in a phreatic aquifer adjoining a partially penetrating, tidal. estuary is investigated through two-dimensional numerical experiments for a lateral cross-section, which explore the influence of factors, such as aquifer and soil materials, tidal amptitudes, and regional groundwater hydraulic gradients. The density contrast between estuarine water and the fresh groundwater drives saltwater penetration of the aquifer even in the case of a marked groundwater hydraulic gradient towards the estuary. We show that tidal fluctuations in estuaries can significantly affect the groundwater salinity distribution in adjacent density-stratified phreatic aquifers. This has consequences for the expected distribution of salinity-sensitive biota in the hyporheic zone as well as vegetation and fauna dependent on water in the riparian soil and aquifer. The shape of the dense saltwater wedge propagating into the adjacent groundwater system is also modified by the estuarine tidal signal, although this effect appears to have only minor influence on the maximum distance penetrated into the aquifer (i.e., location of the 'toe' of the wedge). Tide-induced changes to riparian groundwater salinity are advection-driven, as evidenced by the modified time-averaged groundwater flow dynamics. (c) 2006 Elsevier B.V. All rights reserved.

Measurement and modelling of controlled beach groundwater levels under wave action

New laboratory scale experimental data are presented on the forcing of beach groundwater levels by wave run-up. The experimental setup simulates a coastal barrier dividing the ocean from a relatively constant back beach water level, conditions approximating a closed off lagoon system or beach aquifer. The data are critically compared to an advanced numerical model for simulating wave and beach groundwater interaction in the coastal zone, and provide the first experimental verification of such a model. Overall model-data comparisons are good, but some systematic discrepancies are apparent, and reasons for these are discussed.

Indagine modellistica sulla tenuta idraulica delle difese arginali deputate alla protezione idraulica del territorio

La prima parte di questo lavoro di tesi tratta dell’interazione tra un bacino di laminazione e il sottostante acquifero: è in fase di progetto, infatti, la costruzione di una cassa di espansione sul torrente Baganza, a monte della città di Parma. L’obiettivo di tale intervento è di ridurre il rischio di esondazione immagazzinando temporaneamente, in un serbatoio artificiale, la parte più pericolosa del volume di piena che verrebbe rilasciata successivamente con portate che possono essere agevolmente contenute nel tratto cittadino del torrente. L’acquifero è stato preliminarmente indagato e monitorato permettendone la caratterizzazione litostratigrafica. La stratigrafia si può riassumere in una sequenza di strati ghiaioso-sabbiosi con successione di lenti d’argilla più o meno spesse e continue, distinguendo due acquiferi differenti (uno freatico ed uno confinato). Nel presente studio si fa riferimento al solo acquifero superficiale che è stato modellato numericamente, alle differenze finite, per mezzo del software MODFLOW_2005. L'obiettivo del presente lavoro è di rappresentare il sistema acquifero nelle condizioni attuali (in assenza di alcuna opera) e di progetto. La calibrazione è stata condotta in condizioni stazionarie utilizzando i livelli piezometrici raccolti nei punti d’osservazione durante la primavera del 2013. I valori di conducibilità idraulica sono stati stimati per mezzo di un approccio geostatistico Bayesiano. Il codice utilizzato per la stima è il bgaPEST, un software gratuito per la soluzione di problemi inversi fortemente parametrizzati, sviluppato sulla base dei protocolli del software PEST. La metodologia inversa stima il campo di conducibilità idraulica combinando osservazioni sullo stato del sistema (livelli piezometrici nel caso in esame) e informazioni a-priori sulla struttura dei parametri incogniti. La procedura inversa richiede il calcolo della sensitività di ciascuna osservazione a ciascuno dei parametri stimati; questa è stata valutata in maniera efficiente facendo ricorso ad una formulazione agli stati aggiunti del codice in avanti MODFLOW_2005_Adjoint. I risultati della metodologia sono coerenti con la natura alluvionale dell'acquifero indagato e con le informazioni raccolte nei punti di osservazione. Il modello calibrato può quindi essere utilizzato come supporto alla progettazione e gestione dell’opera di laminazione. La seconda parte di questa tesi tratta l'analisi delle sollecitazioni indotte dai percorsi di flusso preferenziali causati da fenomeni di piping all’interno dei rilevati arginali. Tali percorsi preferenziali possono essere dovuti alla presenza di gallerie scavate da animali selvatici. Questo studio è stato ispirato dal crollo del rilevato arginale del Fiume Secchia (Modena), che si è verificato in gennaio 2014 a seguito di un evento alluvionale, durante il quale il livello dell'acqua non ha mai raggiunto la sommità arginale. La commissione scientifica, la cui relazione finale fornisce i dati utilizzati per questo studio, ha attribuito, con molta probabilità, il crollo del rilevato alla presenza di tane di animali. Con lo scopo di analizzare il comportamento del rilevato in condizioni integre e in condizioni modificate dall'esistenza di un tunnel che attraversa il manufatto arginale, è stato realizzato un modello numerico 3D dell’argine mediante i noti software Femwater e Feflow. I modelli descrivono le infiltrazioni all'interno del rilevato considerando il terreno in entrambe le porzioni sature ed insature, adottando la tecnica agli elementi finiti. La tana è stata rappresentata da elementi con elevata permeabilità e porosità, i cui valori sono stati modificati al fine di valutare le diverse influenze sui flussi e sui contenuti idrici. Per valutare se le situazioni analizzate presentino o meno il verificarsi del fenomeno di erosione, sono stati calcolati i valori del fattore di sicurezza. Questo è stato valutato in differenti modi, tra cui quello recentemente proposto da Richards e Reddy (2014), che si riferisce al criterio di energia cinetica critica. In ultima analisi è stato utilizzato il modello di Bonelli (2007) per calcolare il tempo di erosione ed il tempo rimanente al collasso del rilevato.

Theory and application of inverse problems in groundwater: numerical, laboratory and field studies.

Aquifers are a vital water resource whose quality characteristics must be safeguarded or, if damaged, restored. The extent and complexity of aquifer contamination is related to characteristics of the porous medium, the influence of boundary conditions, and the biological, chemical and physical processes. After the nineties, the efforts of the scientists have been increased exponentially in order to find an efficient way for estimating the hydraulic parameters of the aquifers, and thus, recover the contaminant source position and its release history. To simplify and understand the influence of these various factors on aquifer phenomena, it is common for researchers to use numerical and controlled experiments. This work presents some of these methods, applying and comparing them on data collected during laboratory, field and numerical tests. The work is structured in four parts which present the results and the conclusions of the specific objectives.

Quantitative risk assessment of groundwater quality utilizing GIS technology and coupled groundwater models

The thesis presents a two-dimensional Risk Assessment Method (RAM) where the assessment of risk to the groundwater resources incorporates both the quantification of the probability of the occurrence of contaminant source terms, as well as the assessment of the resultant impacts. The approach emphasizes the need for a greater dependency on the potential pollution sources, rather than the traditional approach where assessment is based mainly on the intrinsic geo-hydrologic parameters. The risk is calculated using Monte Carlo simulation methods whereby random pollution events were generated to the same distribution as historically occurring events or a priori potential probability distribution. Integrated mathematical models then simulate contaminant concentrations at the predefined monitoring points within the aquifer. The spatial and temporal distributions of the concentrations were calculated from repeated realisations, and the number of times when a user defined concentration magnitude was exceeded is quantified as a risk. The method was setup by integrating MODFLOW-2000, MT3DMS and a FORTRAN coded risk model, and automated, using a DOS batch processing file. GIS software was employed in producing the input files and for the presentation of the results. The functionalities of the method, as well as its sensitivities to the model grid sizes, contaminant loading rates, length of stress periods, and the historical frequencies of occurrence of pollution events were evaluated using hypothetical scenarios and a case study. Chloride-related pollution sources were compiled and used as indicative potential contaminant sources for the case study. At any active model cell, if a random generated number is less than the probability of pollution occurrence, then the risk model will generate synthetic contaminant source term as an input into the transport model. The results of the applications of the method are presented in the form of tables, graphs and spatial maps. Varying the model grid sizes indicates no significant effects on the simulated groundwater head. The simulated frequency of daily occurrence of pollution incidents is also independent of the model dimensions. However, the simulated total contaminant mass generated within the aquifer, and the associated volumetric numerical error appear to increase with the increasing grid sizes. Also, the migration of contaminant plume advances faster with the coarse grid sizes as compared to the finer grid sizes. The number of daily contaminant source terms generated and consequently the total mass of contaminant within the aquifer increases in a non linear proportion to the increasing frequency of occurrence of pollution events. The risk of pollution from a number of sources all occurring by chance together was evaluated, and quantitatively presented as risk maps. This capability to combine the risk to a groundwater feature from numerous potential sources of pollution proved to be a great asset to the method, and a large benefit over the contemporary risk and vulnerability methods.

GIS linked environmental process models

In recent years there has been a great effort to combine the technologies and techniques of GIS and process models. This project examines the issues of linking a standard current generation 2½d GIS with several existing model codes. The focus for the project has been the Shropshire Groundwater Scheme, which is being developed to augment flow in the River Severn during drought periods by pumping water from the Shropshire Aquifer. Previous authors have demonstrated that under certain circumstances pumping could reduce the soil moisture available for crops. This project follows earlier work at Aston in which the effects of drawdown were delineated and quantified through the development of a software package that implemented a technique which brought together the significant spatially varying parameters. This technique is repeated here, but using a standard GIS called GRASS. The GIS proved adequate for the task and the added functionality provided by the general purpose GIS - the data capture, manipulation and visualisation facilities - were of great benefit. The bulk of the project is concerned with examining the issues of the linkage of GIS and environmental process models. To this end a groundwater model (Modflow) and a soil moisture model (SWMS2D) were linked to the GIS and a crop model was implemented within the GIS. A loose-linked approach was adopted and secondary and surrogate data were used wherever possible. The implications of which relate to; justification of a loose-linked versus a closely integrated approach; how, technically, to achieve the linkage; how to reconcile the different data models used by the GIS and the process models; control of the movement of data between models of environmental subsystems, to model the total system; the advantages and disadvantages of using a current generation GIS as a medium for linking environmental process models; generation of input data, including the use of geostatistic, stochastic simulation, remote sensing, regression equations and mapped data; issues of accuracy, uncertainty and simply providing adequate data for the complex models; how such a modelling system fits into an organisational framework.

Concepts and methods of quantitative assessment of risk to groundwater resources

This work presents a two-dimensional approach of risk assessment method based on the quantification of the probability of the occurrence of contaminant source terms, as well as the assessment of the resultant impacts. The risk is calculated using Monte Carlo simulation methods whereby synthetic contaminant source terms were generated to the same distribution as historically occurring pollution events or a priori potential probability distribution. The spatial and temporal distributions of the generated contaminant concentrations at pre-defined monitoring points within the aquifer were then simulated from repeated realisations using integrated mathematical models. The number of times when user defined ranges of concentration magnitudes were exceeded is quantified as risk. The utilities of the method were demonstrated using hypothetical scenarios, and the risk of pollution from a number of sources all occurring by chance together was evaluated. The results are presented in the form of charts and spatial maps. The generated risk maps show the risk of pollution at each observation borehole, as well as the trends within the study area. This capability to generate synthetic pollution events from numerous potential sources of pollution based on historical frequency of their occurrence proved to be a great asset to the method, and a large benefit over the contemporary methods.

Groundwater flow patterns within the Triassic sandstone aquifers, Birmingham, United Kingdom

This paper presents the development of a modelling study for part of the Birmingham area. Restricted access and model resolutions have limited wide applications of some of the previously developed models. The study area covers approximately 221 km2, and is underlain geologically, by a multi-layer setup with varied hydraulic properties. The basal aquifer unit is the Kidderminster sandstone Formation, overlain by the Wildmoor and Bromsgrove sandstone Formations. The presence of the Birmingham fault which acts as low permeability barrier demarcates the eastern and southern boundaries. The western boundary is defined by the presence of crystallised rocks and coal measures, while a groundwater divide defines the northern boundary. The estimated recharge flux is 112 mm/yr. The ranges of calibrated values obtained for horizontal and vertical hydraulic conductivities are 5.787x10-6 - 2.315x10-5  m/s and 5.787x10-8  - 1.157x10-7  m/s, respectively. Corresponding values obtained for the specific yield and specific storage are 0.10 - 0.12, and 1x10 -4 - 5x10 -4. The calculated numerical error is generally much less than 0.1 %. Hydraulic layering within the Permo-Triassic sandstone aquifer is thought to account for the large vertical anisotropy. Although, uncertainties are associated with the use of a simplistic delay approach to characterise the effects of the unsaturated zone, the modelled values are comparable with those obtained in the literature, and the flow pattern predictions appear to be realistic. © Research India Publications.

Flow and water budgets in the C-111 and L-31W canals near the Everglades National Park, Dade County, Florida

Acoustic velocity meter (AVM) sites, located both distant and adjacent to canal water control structures, were constructed and calibrated in L-31W borrow canal and Canal 111 (C-111) to measure canal water velocity. Data were used to compute monthly discharge volumes and overall water budgets for several canal reaches from August 1994 to May 1996. The water budgets indicated extensive aquifer inflows in L-31W associated, in part, with S-332 pump station return flows. Canal and groundwater piezometer data showed 5 distinct hydrologic scenarios (distinguished by the direction and magnitude of hydraulic gradients) in the important Frog Pond area on the eastern boundary of the Everglades National Park. Most of the water lost from C-111 was via surface water losses near the outlet of the system, close to Florida Bay. The distribution of flows during the study suggest an alteration of the present South Dade Conveyance System modification plan to improve water deliveries to Taylor Slough and the Eastern Panhandle of the Everglades National Park. ^

Natural organic matter and colloid-facilitated arsenic transport and transformation in porous soil media

Prediction of arsenic transport and transformation in soil environment requires understanding the transport mechanisms and proper estimation of arsenic partitioning tong all three phases in soil/aquifer systems: mobile colloids, mobile soil solution, and immobile soil solids. The primary purpose of this research is to study natural dissolved organic matter (DOM)/colloid-facilitated transport of arsenic and understand the role of soil derived carriers in the transport and transformation of both inorganic and organoarsenicals in soils. ^ DOM/colloid facilitated arsenic transport and transformation in porous soil media were investigated using a set of experimental approaches including batch experiment, equilibrium membrane dialysis experiment and column experiment. Soil batch experiment was applied to investigate arsenic adsorption on a variety of soils with different characteristics; Equilibrium membrane dialysis was employed to determine the 'free' and 'colloid-bound/complexed' arsenic in water extracts of chosen soils; Column experiments were also set up in the laboratory to simulate arsenic transport and transformation through golf course soils in the presence and absence of soil-derived dissolved substances. ^ The experimental results revealed that organic matter amendments effectively reduced soil arsenic adsorption. The majority of arsenic present in the soil extracts was associated with small substances of molecular weight (MW) between 500 and 3,500 Da, Only a small fraction of arsenic was associated with higher MW substances (MW > 3,500 Da), which was operationally defined as colloidal part in this study. The association of arsenic and DOM in the soil extracts strongly affected arsenic bioavailability, arsenic transport and transformation in soils. The results of column experiments revealed arsenic complicated behavior with various processes occurring in soils studied, including: soil arsenic' adsorption, facilitated arsenic transportation by dissolved substances presented in soil extracts and microorganisms involved arsenic species transformation. ^ Soil organic matter amendments effectively reduce soil arsenic adsorption capability either by scavenging 'soil arsenic adsorption sites or by interactions between arsenic species and dissolved organic chemicals in soil solution. Close attention must be paid for facilitated arsenic transport by dissolved substances presented in soil solution and microorganisms involved arsenic species transformation in arsenic-contaminated soils.^

Lattice Boltzmann modeling of fluid flow and solute transport in karst aquifers

A novel modeling approach is applied to karst hydrology. Long-standing problems in karst hydrology and solute transport are addressed using Lattice Boltzmann methods (LBMs). These methods contrast with other modeling approaches that have been applied to karst hydrology. The motivation of this dissertation is to develop new computational models for solving ground water hydraulics and transport problems in karst aquifers, which are widespread around the globe. This research tests the viability of the LBM as a robust alternative numerical technique for solving large-scale hydrological problems. The LB models applied in this research are briefly reviewed and there is a discussion of implementation issues. The dissertation focuses on testing the LB models. The LBM is tested for two different types of inlet boundary conditions for solute transport in finite and effectively semi-infinite domains. The LBM solutions are verified against analytical solutions. Zero-diffusion transport and Taylor dispersion in slits are also simulated and compared against analytical solutions. These results demonstrate the LBM’s flexibility as a solute transport solver. The LBM is applied to simulate solute transport and fluid flow in porous media traversed by larger conduits. A LBM-based macroscopic flow solver (Darcy’s law-based) is linked with an anisotropic dispersion solver. Spatial breakthrough curves in one and two dimensions are fitted against the available analytical solutions. This provides a steady flow model with capabilities routinely found in ground water flow and transport models (e.g., the combination of MODFLOW and MT3D). However the new LBM-based model retains the ability to solve inertial flows that are characteristic of karst aquifer conduits. Transient flows in a confined aquifer are solved using two different LBM approaches. The analogy between Fick’s second law (diffusion equation) and the transient ground water flow equation is used to solve the transient head distribution. An altered-velocity flow solver with source/sink term is applied to simulate a drawdown curve. Hydraulic parameters like transmissivity and storage coefficient are linked with LB parameters. These capabilities complete the LBM’s effective treatment of the types of processes that are simulated by standard ground water models. The LB model is verified against field data for drawdown in a confined aquifer.

Larger foraminiferal biostratigraphy, systematics and paleoenvironments of the Avon Park Formation and Ocala Limestone, Highlands County, Florida

This study investigates the use of larger foraminifera in determining the biostratigraphy of the Avon Park Formation and the Ocala Limestone in central Florida. Sedimentary rocks of the Avon Park Formation are the oldest exposed deposits in the state of Florida, and together with the Ocala Limestone comprise a part of the confining unit of the Floridan Aquifer, a major source of Florida's water supply. ^ Material from the ROMP 29A core collected by the U.S. Geological Survey was evaluated and compared to previous studies of the biostratigraphy of the formations. The larger foraminifera of the Avon Park Formation were examined in thin section, and those of the Ocala Limestone were free specimens. The larger foraminifera from both units were described and identified, and the biostratigraphy determined. The morphological features of the larger foraminifera of the Ocala Limestone were measured and analyzed at various depths within the ROMP 29A core.^ The Avon Park Formation contains predominantly the shallow-water, conical foraminifera Fallotella cookei, Fallotella floridana, Pseudochrysalidina floridana, Coleiconus christianaensis, Coleiconus sp. A, Coskinolina sp. A, Coskinolina sp. B, Fallotella sp. A, Fallotella sp. B, Fabularia vaughani and larger miliolids. ^ The Ocala Limestone contains a different, deeper water assemblage that included the larger foraminifera Heterostegina ocalana, Lepidocyclina ocalana varieties, Lepidocyclina chaperi, Lepidocyclina pustulosa, Nummulites willcoxi, Nummulites striatoreticulatus, Nummulites floridensis and Pseudophragmina spp. A, B, and C. The age of the Avon Park Formation was corroborated by the occurrence of the biomarker echinoid Neolaganum dalli as Eocene, and the Ocala Limestone also contained Eocene larger foraminifera with Eocene to possibly Oligocene calcareous nannofossils. The distribution of the larger foraminifera of the Avon Park Formation was correlated with the subtidal and peritidal zones of the continental shelf. Analyses of variance showed that the changes in measurements of the morphology in Heterostegina ocalana, Lepidocyclina spp. and Nummulites spp. were correlated with change in the depositional environments.^

Development of an integrated surface and subsurface model of Everglades National Park

An integrated surface-subsurface hydrological model of Everglades National Park (ENP) was developed using MIKE SHE and MIKE 11 modeling software. The model has a resolution of 400 meters, covers approximately 1050 square miles of ENP, includes 110 miles of drainage canals with a variety of hydraulic structures, and processes hydrological information, such as evapotranspiration, precipitation, groundwater levels, canal discharges and levels, and operational schedules. Calibration was based on time series and probability of exceedance for water levels and discharges in the years 1987 through 1997. Model verification was then completed for the period of 1998 through 2005. Parameter sensitivity in uncertainty analysis showed that the model was most sensitive to the hydraulic conductivity of the regional Surficial Aquifer System, the Manning's roughness coefficient, and the leakage coefficient, which defines the canal-subsurface interaction. The model offers an enhanced predictive capability, compared to other models currently available, to simulate the flow regime in ENP and to forecast the impact of topography, water flows, and modifying operation schedules.

Chilling damage in a changing climate in coastal landscapes of the subtropical zone: a case study from south Florida

Extensive portions of the southern Everglades are characterized by series of elongated, raised peat ridges and tree islands oriented parallel to the predominant flow direction, separated by intervening sloughs. Tall herbs or woody species are associated with higher elevations and shorter emergent or floating species are associated with lower elevations. The organic soils in this “Ridge-and-Slough” landscape have been stable over millennia in many locations, but degrade over decades under altered hydrologic conditions. We examined soil, pore water, and leaf phosphorus (P) and nitrogen (N) distributions in six Ridge and Slough communities in Shark Slough, Everglades National Park. We found P enrichment to increase and N to decrease monotonically along a gradient from the most persistently flooded sloughs to rarely flooded ridge environments, with the most dramatic change associated with the transition from marsh to forest. Leaf N:P ratios indicated that the marsh communities were strongly P-limited, while data from several forest types suggested either N-limitation or co-limitation by N and P. Ground water stage in forests exhibited a daytime decrease and partial nighttime recovery during periods of surface exposure. The recovery phase suggested re-supply from adjacent flooded marshes or the underlying aquifer, and a strong hydrologic connection between ridge and slough. We therefore developed a simple steady-state model to explore a mechanism by which a phosphorus conveyor belt driven by both evapotranspiration and the regional flow gradient can contribute to the characteristic Ridge and Slough pattern. The model demonstrated that evapotranspiration sinks at higher elevations can draw in low concentration marsh waters, raising local soil and water P concentrations. Focusing of flow and nutrients at the evapotranspiration zone is not strong enough to overcome the regional gradient entirely, allowing the nutrient to spread downstream and creating an elongated concentration plume in the direction of flow. Our analyses suggest that autogenic processes involving the effects of initially small differences in topography, via their interactions with hydrology and nutrient availability, can produce persistent physiographic patterns in the organic sediments of the Everglades.

Use of tritium and helium to define groundwater flow conditions in Everglades National Park

The concentrations of tritium (3H) and helium isotopes (3He and4He) were used as tracers of groundwater flow in the surficial aquifer system (SAS) beneath Everglades National Park (ENP), south Florida. From ages determined by 3H/3He dating techniques, groundwater within the upper 28 m originated within the last 30 years. Below 28 m, waters originated prior to 30 years before present with evidence of mixing at the interface. Interannual variation of the 3H/3He ages within the upper 28 m was significant throughout the 3 year investigation, corresponding with varying hydrologic conditions. In the region of Taylor Slough Bridge, younger groundwater was consistently detected below older groundwater in the Biscayne Aquifer, suggesting preferential flow to the lower part of the aquifer. An increase in 4He with depth in the SAS indicated that radiogenic 4He produced in the underlying Hawthorn Group migrates into the SAS by diffusion. Higher Δ4He values in brackish groundwaters compared to fresh waters from similar depths suggested a possible enhanced vertical transport of4He in the seawater mixing zone. Groundwater salinity measurements indicated the presence of a wide (6–28 km) seawater mixing zone. Comparison of groundwater levels with surface water levels in this zone indicated the potential for brackish groundwater discharge to the overlying Everglades surface water.