Greffage d’un film mince de nano-TiO2 sur les fibres naturelles cellulosiques pour le renforcement de biocomposites polymériques

Abstract : Natural materials have received a full attention in many applications because they are degradable and derived directly from earth. In addition to these benefits, natural materials can be obtained from renewable resources such as plants (i.e. cellulosic fibers like flax, hemp, jute, and etc). Being cheap and light in weight, the cellulosic natural fiber is a good candidate for reinforcing bio-based polymer composites. However, the hydrophilic nature -resulted from the presence of hydroxyl groups in the structure of these fibers- restricts the application of these fibers in the polymeric matrices. This is because of weak interfacial adhesion, and difficulties in mixing due to poor wettability of the fibers within the matrices. Many attempts have been done to modify surface properties of natural fibers including physical, chemical, and physico-chemical treatments but on the one hand, these treatments are unable to cure the intrinsic defects of the surface of the fibers and on the other hand they cannot improve moisture, and alkali resistance of the fibers. However, the creation of a thin film on the fibers would achieve the mentioned objectives. This study aims firstly to functionalize the flax fibers by using selective oxidation of hydroxyl groups existed in cellulose structure to pave the way for better adhesion of subsequent amphiphilic TiO[subscript 2] thin films created by Sol-Gel technique. This method is capable of creating a very thin layer of metallic oxide on a substrate. In the next step, the effect of oxidation on the interfacial adhesion between the TiO[subscript 2] film and the fiber and thus on the physical and mechanical properties of the fiber was characterized. Eventually, the TiO[subscript 2] grafted fibers with and without oxidation were used to reinforce poly lactic acid (PLA). Tensile, impact, and short beam shear tests were performed to characterize the mechanical properties while Thermogravimetric analysis (TGA), Differential Scanning Calorimetry (DSC), Dynamic mechanical analysis (DMA), and moisture absorption were used to show the physical properties of the composites. Results showed a significant increase in physical and mechanical properties of flax fibers when the fibers were oxidized prior to TiO[subscript 2] grafting. Moreover, the TiO[subscript 2] grafted oxidized fiber caused significant changes when they were used as reinforcements in PLA. A higher interfacial strength and less amount of water absorption were obtained in comparison with the reference samples.

Desenvolvimento e caracterização do queijo Santo Giorno, típico do sudoeste do Paraná, produzido com leite cru e fermento endógeno

Two cheese formulations made from raw milk and endogenous yeasts with 30, 60 and 180 days of maturation in two dairy Paraná Southwest were studied to evaluate their quality through physical, physical-chemical, microbiological and sensorial characteristics, as one of the stages of development of a typical regional cheese. The production was accompanied from designing the flowchart processing, where the samples were collected to perform the analysis of proteins, lipids, moisture, ash, carbohydrates, total solids, fat in dry matter, calories; water activity, instrumental texture (hardness, adhesiveness, springiness, cohesiveness, resiliency and chewiness), instrumental color (CIE Lab); microbiological quality was assessed searching for total and thermotolerant coliforms, coagulase positive staphylococci and Salmonella spp.; the acceptance related to sensory characteristics of color, appearance, flavor, texture, taste and purchase intent was evaluated through the structured hedonic scale. This research contributed information relevant to the production process, such as the realization of the viability in freeze-drying lactic acid bacteria yeast isolated from milk in the Southwestern Mesoregion of Parana and the results of the analysis of the cheese showed similarity between formulations, regarding the physical, physical-chemical characterization, moreover good microbiological quality, where the differences between samples of dairy products were not perceived by sensory panelists. Adjustments in standardization related to technological quality control is an extremely important factor for the success of dairy companies and small producers involved in the project and that they have the option of producing the Santo Giorno, a fine cheese, with the great advantage of adding features of region, with high standard of sanitary conditions and with great consumer acceptance of indicative.

Utilização de bagaço de maçã como ingrediente alimentar em iogurte com potencial efeito benéfico para a saúde

O desenvolvimento de alimentos funcionais evoluiu consideravelmente ao longo dos anos e a capacidade tecnológica para produzir um alimento com compostos fisiologicamente ativos tem crescido significativamente. O presente trabalho teve como objetivo criar um novo alimento, utilizando um subproduto proveniente da indústria agroalimentar. O alimento seleccionado foi o iogurte natural, o qual foi enriquecido com um extrato de bagaço de maçã. O bagaço de maçã contém compostos fenólicos e fibra, mostrando atividade antioxidante significativa e por conseguinte apresenta um potencial efeito positivo na saúde. Avaliaram-se características químicas do bagaço de maçã e das farinhas obtidas a partir deste subproduto, designadamente: acidez, teor em açúcares totais e redutores, cinza, matéria gorda, humidade, proteína bruta, fibra dietética insolúvel e solúvel. O extrato aquoso obtido a partir do subproduto foi também caracterizado quanto ao seu conteúdo fenólico e atividade antioxidante. O iogurte produzido com incorporação do extrato de bagaço de maçã foi estudado do ponto de vista de parâmetros químicos tais como acidez, açúcares totais, cinza, humidade, proteína bruta, pH e fibra bruta, conteúdo em fenólicos totais e atividade antioxidante. O subproduto, os extratos e o iogurte foram também avaliados quanto à sua carga microbiológica. Na caracterização química do bagaço foram obtidos os seguintes valores, expressos em base seca: 2,0±0,01% de acidez (expressa em equivalentes de ácido málico); 15,96±1,53% de açúcares totais; 13,35±1,91% de açúcares redutores; 1,88±0,07% de cinza, 2,49±0,5% de matéria gorda, 81,17±1,98% de humidade e 5,01±0,01% de proteína bruta. Quanto ao seu conteúdo em fibra dietética, o bagaço contém na sua composição 65,80% de fibra dietética insolúvel e 4,90% de fibra dietética solúvel. A farinha obtida após secagem a 60 °C do bagaço de maçã apresentou, na base seca, 1,9±0,04% de acidez, 10,57±1,31% de açúcares totais; 8,50±1,00% de açúcares redutores; 2,22±0,04%de cinza, 4,73±0,11% de matéria gorda, 6,34±0,62% de humidade e 5,40±0,26% de proteína. A atividade antioxidante do extrato aquoso, (AQ_6X10) obtido do bagaço de maçã, utilizado para incorporação no iogurte, determinada através do método ABTS foi de 5,00±1,28µmol TE/g amostra e apresentou um teor em compostos fenólicos de 221,42±0,734 mg EAG/ 100g de extrato, na base seca. Ao nível microbiológico o extrato revelou parâmetros aceitáveis, de acordo com a tabela 13 (anexos 3), para utilização como ingrediente alimentar. Os iogurtes produzidos foram analisados quimicamente. O iogurte, com extrato aquoso de bagaço de maçã incorporado, apresentou 89,64±0,00% de humidade, 0,93±0,00% de acidez (expressa em equivalentes de ácido láctico); 6,42±0,26% de açúcares totais; 0,74%±0,00% de cinza, 3,83±0,00% de proteína bruta e 0,2±0,00% de fibra bruta. O seu conteúdo em compostos fenólicos foi de 12,41±1,69mg EAG/ 100g de iogurte, e a sua atividade antioxidante foi 54,84±4,40 µmol TE/g iogurte. Avaliou-se ainda o iogurte no que diz respeito ao crescimento de bactérias lácticas e constatou-se, por comparação com o iogurte de controlo, que estas se desenvolveram normalmente ao longo do processo de fabrico. A análise microbiológica revelou ainda que o iogurte é seguro do ponto de vista alimentar de acordo com a Tabela 15 (anexos 3). A análise sensorial realizada aos iogurtes demonstrou que o iogurte fortificado apresentou uma aceitação muito boa pelo painel de provadores. O presente estudo demonstrou que o bagaço de maçã, um subproduto das indústrias agroalimentares, é seguro do ponto de vista microbiológico, podendo ser utilizado na preparação de ingredientes alimentares para serem incorporados, por exemplo em iogurte, conferindo-lhe características que se destacam pelo maior teor em fibra e atividade antioxidante em relação ao iogurte não enriquecido, e atributos sensoriais apelativos em termos de textura e sabor.

Avaliação do potencial probiótico de leveduras isoladas de azeitonas de mesa da cultivar Negrinha de Freixo

Probióticos são definidos como microrganismos vivos, que quando administrados em quantidades adequadas, conferem benefícios à saúde do hospedeiro. Atualmente a pesquisa de microrganismos probióticos a partir da fermentação da azeitona tem-se centrado nas bactérias ácido-lácticas, sendo escassos os estudos envolvendo leveduras. No presente trabalho avaliou-se o potencial probiótico de estirpes de leveduras previamente isoladas durante o processo de fermentação natural de azeitona de mesada cultivar Negrinha de Freixo. Foram avaliadas 16 estirpes em relação à atividade enzimática (catalase, amilase, xilanase, protease e β-glucosidase); ao crescimento a 37ºC; ação inibitória frente a microrganismos patogénicos; capacidade de autoagregação; atividade antioxidante (utilizando o método de DPPH); e resistência ao aparelho digestivo humano, a partir de uma simulação in vitro da digestão gástrica e pancreática. Os resultados apresentados para a atividade enzimática indicaram que em alguns isolados foi detetado fraca atividade das enzimas protease, xilanase e amilase. Já uma atividade forte de lipase foi observada nas estirpes Pichia manshurica e Saccharomyces cerevisiae (15A e 15B). Para a enzima β-glucosidase, identificou-se atividade forte em Rhodotorula graminis, Rhodotorula glutinis, Candida norvegica, Pichia guilliermondii e Galactomyces reessii. Relativamente à capacidade de crescimento à temperatura corporal (37ºC), três estirpes (Saccharomyces cerevisiae 15B; Candida tropicalis 1A; e Pichia membranifaciens 29A) destacaram-se por apresentar maior taxa específica de crescimento. A capacidade bloqueadora dos radicais livres DPPH foi verificada em 10 estirpes, sendo as estirpes de S. cerevisiae as que mais se destacaram dentre as outras. As estirpes C. norvegica e G. reessii (34A) apresentaram capacidade antifúngica frente ao microrganismo patogénico Cryptococcus neoformans. Em relação à capacidade de autoagregação avaliada, as estirpes S. cerevisiae (15A), Candida tropicalis (1A) e C. norvegica (7A) apresentaram ao fim de 24 horas percentagens superiores a 80%. Relativamenteà resistência frente às condições presentes no trato gastrointestinal in vitro, a estirpe P. guilliermondii (25A), destacou-se dentre as demais, por apresentar maior capacidade de sobrevivência em todo o processo digestivo simulado. As estirpes Candida boidinii (37A) e S. cerevisiae (15A) apresentaram menor capacidade de sobrevivência nestas condições. Contudo, serão necessários testes adicionais para complementar estes resultados.

Effect of commercial starter cultures and native yeasts on ochratoxin a production by aspergillus westerdijkiae and penicillium nordicum in meat products

Processed meat products are of worldwide importance and, because of their intrinsic factors as well as the processing methods, they are highly prone to fungal and mycotoxin contamination. Ochratoxin A (OTA) is the most significant mycotoxin in processed meat products. Penicillium nordicum is considered to be responsible for OTA contamination of meat products, as it is highly adapted to salt and protein-rich matrices and is moderately psycrotrophic. However, another OTA-producing fungus, Aspergillus westerdijkiae, adapted to carbon-rich matrices such as cereals and coffee beans, has been recently associated with high levels of OTA in meat products. Several Lactic Acid Bacteria (LAB) and yeasts have been tested as biocontrol agents against P. nordicum growth and OTA production in meat products, with promising results, but none of the studies have considered A. westerdijkiae. The aim of this work was to evaluate in vitro the effect of a commercial starter culture used in sausage fermentation and four yeasts isolated from dry-cured sausage on these two OTA-producing fungi, both in terms of fungal growth and of OTA production, using different meat-based culture media as model systems. The mechanisms underlying the observed effect were also studied. For this purpose, C. krusei, C. zeylanoides, R. mucilaginosa, R. glutinis, a mix of these yeasts and the starter culture were co-inoculated with P. nordicum and A. westerdijkiae in industrial sausage, traditional sausage, and ham-based media, under conditions of water activity, salt concentration and temperature that mimic real conditions at beginning and end of sausage curing process. Fungal growth was determined by measuring colony diameter, and OTA production was quantified by HPLC-FLD after extraction with methanol. Yeasts where found to inhibit significantly the growth of both fungi. P. nordicum was unable to produce detectable OTA in both sausage-based media under any condition. In ham, yeasts reduced OTA production, while the starter culture significantly increased it. Unexpectedly, OTA production by A. westerdijkiae was significantly stimulated in all media tested by all microorganisms. Matrix has a significant effect on OTA production by P. nordicum, but not by A. westerdijkiae, for which only temperature showed to have effect. By testing the mechanisms of action by which starter culture and C. zeylanoides influenced fungal responses, we were able to determine that direct contact and simultaneous growth of test organisms were the mechanisms more significantly involved in the responses. In conclusion, ochratoxigenic fungi do not all respond to antagonistic microorganisms in the same way. The use of biocontrol agents with the intent of reducing fungal growth and mycotoxin production by one fungus can have unexpected effects on others, thus leading to unforeseen safety problems. Further experiments are recommended to properly understand the reasons behind the different effects of microorganisms, to ensure their safe as biocontrol agents.

Preparation of Ni-P electroless and its corrosion resistance against sea water

Electroless coating is much appropriate process at engineering surface. Since the discovery of electroless nickel-phosphorus coating in 3996, due to technical and economic advantages as well as desirable characteristics such as resistance to corrosion, abrasion and a high hardness has found wide application at engineering industries. Properties of electroless nickel-phosphorus coating depend on the characteristics of the used bath and heat treatment. In this study, optimal conditions and concentration of sodium citrate, sodium acetate and lactic acid in the bath of electroless nickel-phosphorus coating to the steel ck67 surface was determined. Structure, chemical composition and phases occurring in the coating were investigated using Scanning Electron Microscope (SEM) and X-ray diffraction analysis (XRD). The corrosion behavior of coatings in solution 3.5٪ NaCl was studied using electrochemical. The results showed that corrosion resistance of the coating with composition sodium citrate, sodium acetate and lactic acid decreased respectively.

Efeitos de absorventes de umidade e de aditivos químicos e microbianos sobre o valor nutritivo, o perfil fermentativo e as perdas em silagens de capim-marandu

The objective of this trial was to evaluate the nutritional value, fermentation profile and dry matter losses of Palisadegrass silages ensiled with either dried citrus pulp, soybean hulls, chemical or microbial additives. The trial was carried out in a completely randomized experimental design and in a factorial arrangement (3 x 5), with three dry matter levels (wet forage or forage ensiled with pelleted citrus pulp or pelleted soybean hulls) and five additives (without or with the presence of bacterial inoculants or the addition of: sodium benzoate, formic acid in the concentration of 62% or 44%), totalizing 15 treatments and 60 experimental silos. The variables analyzed were: nutritional value, losses due to gases and effluents, and dry matter recovery. The use of dried citrus pulp or soybean hulls at the ensiling time increased the dry matter content (29.4 and 28,9%) and decreased the effluent production (4.1 and 3.8 kg/t of fresh matter), also providing fermentable substrate to microorganisms, resulting in increased fermentation coefficient and digestibility of silages. The use of formic acid resulted in silages with higher digestibility and increased water-soluble carbohydrates and crude protein content. This additive was also effective in reducing the losses due to gases and, as a result, increased the total dry matter recovery. The treatment containing homolactic bacteria showed similar trend of increasing the digestibility and reducing the losses due to gases. The use of sodium benzoate was less effective in altering the fermentation pattern of tropical silages. The nutritional value and total dry matter losses of silages ensiled without additives can be considered satisfactory. However, wet forage ensiled with dried citrus pulp and, mainly, with soybeans hulls showed the best results. Treatments containing formic acid had a beneficial effect on the fermentation profile of tropical grass silages.

Aditivos químicos e biológicos na ensilagem de cana-de-açúcar: 1. composição química das silagens, ingestão, digestibilidade e comportamento ingestivo

Avaliou-se o efeito da inclusão de aditivos na ensilagem de cana-de-açúcar (Saccharum officinarum L.) sobre a composição químico-bromatológica das silagens, o comportamento ingestivo, o consumo voluntário e a digestibilidade em bovinos de corte. Utilizaram-se cinco novilhos da raça Nelore providos de cânula ruminal, alocados em delineamento quadrado latino 5 ´ 5 e alimentados com dietas com 65% de volumoso na MS. Foram avaliadas cinco silagens (base úmida): controle - cana-de-açúcar sem aditivos; uréia - cana-de-açúcar + 0,5% uréia; benzoato - cana-de-açúcar + 0,1% de benzoato de sódio; LP - cana-de-açúcar inoculada com Lactobacillus plantarum (1 ´ 10(6) ufc/g MV); LB - cana-de-açúcar inoculada com L. buchneri (3,6 ´ 10(5) ufc/g forragem). A forragem foi armazenada em silos do tipo poço por 90 dias antes do fornecimento aos animais. A composição químico-bromatológica da cana-de-açúcar foi alterada após a ensilagem, em relação à cana-de-açúcar original, com redução no teor de carboidratos solúveis e na digestibilidade in vitro e elevação relativa nos teores de FDN e FDA. Os teores de etanol (0,30% da MS) e ácidos orgânicos (0,99% de ácido lático e 2,31% de acético) foram baixos e semelhantes entre as silagens. Os aditivos aplicados na ensilagem não promoveram alterações no consumo e na digestibilidade aparente da MS (7,2 kg/dia e 63,6%, respectivamente). O comportamento ingestivo dos animais também não foi alterado, com tempos médios de 230,6; 519,6 e 672,8 minutos/dia despendidos com ingestão de ração, ruminação e ócio, respectivamente. Os aditivos acrescidos à cana-de-açúcar promoveram pequenas alterações na maioria das variáveis avaliadas.

Efficacy of Sakacin on Selected Food Pathogenic Microorganisms Isolated from Fermented Milk Products

The efficacy of sakacin on selected food pathogenic microorganisms isolated from fermented milk products was investigated. The L. sake was isolated using the pour plate technique and was characterized based on it colony, cell morphology and some biochemical tests. This isolate was identified using standard scheme. The L. sake FCF 33 was propagated in De Man Rogosa Sharpe (MRS) broth for bacteriocin (sakacin) production. The sakacin had inhibitory effects on all test microorganisms (ranging from +5mm to +6mm) except Shigella dysenteriae N11, Salmonella typhimurium N8, Klebsiella ozaenae W24 and Proteus mirabilis N16a). Bacteriocins are antimicrobial substances of lactic acid bacteria (LAB) have gained tremendous attention as potential bio preservatives in the food and dairy industries. The LAB can serve as probiotics, which are products aimed at delivering living, potentially beneficial bacterial cells to the gut ecosystem of humans and other animals.

STANDARDIZATION OF CASSAVA MAHEWU FERMENTATION AND ASSESSMENT OF THE EFFECTS OF IRON SOURCES USED FOR FORTIFICATION

Cassava root is the main staple for 70% of the population in Mozambique, particularly in inaccessible rural areas, but is known to be low in iron. Anaemia is a public health problem in mothers and preschool children in Mozambique and up to 40% of these cases are probably due to dietary iron deficiency. The World Health Organization (WHO) and Food and Agriculture Organization of the United Nations (FAO) recognize the fortification of foodstuff as an effective method to remedy dietary deficiencies of micronutrients, including iron. Cassava mahewu, a non-alcoholic fermented beverage is prepared at subsistence level from cassava roots using indigenous procedures. The aim of the study was to standardize mahewu fermentation and investigate if the type of cassava fermented, or the iron compound used for fortification affected the final product. Roots of sweet and bitter varieties of cassava from four districts (Rapale, Meconta, Alto Molocue and Zavala) in Mozambique, were peeled, dried and pounded to prepare flour. Cassava flour was cooked and fermented under controlled conditions (45°C for 24 h). The fermentation period and temperature were set, based on the findings of a pilot study which showed that an end-point pH of about 4.5 was regularly reached after 24 h at 45°C. Cassava mahewu was fortified with ferrous sulfate (FeSO4.7H2O) or ferrous fumarate (C4H2FeO4) at the beginning (time zero) and at the end of fermentation (24 h). The amount of iron added to the mahewu was based on the average of the approved range of iron used for the fortification of maize meal. The mean pH at the endpoint was 4.5, with 0.29% titratable acidity. The pH and acidity were different to those reported in previous studies on maize mahewu, whereas the solid extract of 9.65% was found to be similar. Lactic acid bacteria (LAB) and yeast growth were not significantly different in mahewu fortified with either of the iron compounds. There was no significant difference between cassava mahewu made from bitter or sweet varieties. A standard method for preparation and iron fortification of cassava mahewu was developed. It is recommended that fortification occurs at the end of fermentation when done at household level.

Synthesis of innovative polyelectrolytes using monomers coming from renewable sources

240 p.

Síntese e caracterização do poli(ácido láctico) para potencial uso em sistemas de liberação controlada de fármacos

With the advances in medicine, life expectancy of the world population has grown considerably in recent decades. Studies have been performed in order to maintain the quality of life through the development of new drugs and new surgical procedures. Biomaterials is an example of the researches to improve quality of life, and its use goes from the reconstruction of tissues and organs affected by diseases or other types of failure, to use in drug delivery system able to prolong the drug in the body and increase its bioavailability. Biopolymers are a class of biomaterials widely targeted by researchers since they have ideal properties for biomedical applications, such as high biocompatibility and biodegradability. Poly (lactic acid) (PLA) is a biopolymer used as a biomaterial and its monomer, lactic acid, is eliminated by the Krebs Cycle (citric acid cycle). It is possible to synthesize PLA through various synthesis routes, however, the direct polycondensation is cheaper due the use of few steps of polymerization. In this work we used experimental design (DOE) to produce PLAs with different molecular weight from the direct polycondensation of lactic acid, with characteristics suitable for use in drug delivery system (DDS). Through the experimental design it was noted that the time of esterification, in the direct polycondensation, is the most important stage to obtain a higher molecular weight. The Fourier Transform Infrared (FTIR) spectrograms obtained were equivalent to the PLAs available in the literature. Results of Differential Scanning Calorimetry (DSC) showed that all PLAs produced are semicrystalline with glass transition temperatures (Tgs) ranging between 36 - 48 °C, and melting temperatures (Tm) ranging from 117 to 130 °C. The PLAs molecular weight characterized from Size Exclusion Chromatography (SEC), varied from 1000 to 11,000 g/mol. PLAs obtained showed a fibrous morphology characterized by Scanning Electron Microscopy (SEM)

Síntese do Poli (ácido láctico) por policondensação direta utilizando um planejamento fatorial

The environmental impact caused by the disposal of non-biodegradable polymer packaging on the environment, as well as the high price and scarcity of oil, caused increase of searches in the area of biodegradable polymers from renewable resources were developed. The poly (lactic acid) (PLA) is a promising polymer in the market, with a large availability of raw material for the production of its monomer, as well as good processability. The aimed of this study was synthesis PLA by direct polycondesation of lactic acid, using the tool of experimental design (DOE) (central composite rotatable design (CCRD)) to optimize the conditions of synthesis. The polymer obtained was characterized by scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), viscosimetric analysis, differential scanning calorimeter (DSC) and size exclusion chromatography (SEC). The results confirmed the formation of a poly (lactic acid) semicrystalline in the syntheses performed. Through the central composite rotatable design was possible to optimize the crystallization temperature (Tc) and crystallinity degree (Xc). The crystallization temperature maximum was found for percentage of catalyst around the central point (0,3 (%W)) and values of time ranging from the central point (6h) to the upper level (+1) (8h). The crystallization temperature maximum was found for the total synthesis time of 4h (-1) and percentage of catalyst 0,1(W%) (-1). The results of size exclusion chromatography (SEC) showed higher molecular weights to 0,3 (W%) percent of catalyst and total time synthesis of 3,2h

A BACKING DEVICE BASED ON AN EMBEDDED STIFFENER AND RETRACTABLE INSERTION TOOL FOR THIN-FILM COCHLEAR ARRAYS

Intracochlear trauma from surgical insertion of bulky electrode arrays and inadequate pitch perception are areas of concern with current hand-assembled commercial cochlear implants. Parylene thin-film arrays with higher electrode densities and lower profiles are a potential solution, but lack rigidity and hence depend on manually fabricated permanently attached polyethylene terephthalate (PET) tubing based bulky backing devices. As a solution, we investigated a new backing device with two sub-systems. The first sub-system is a thin poly(lactic acid) (PLA) stiffener that will be embedded in the parylene array. The second sub-system is an attaching and detaching mechanism, utilizing a poly(N-vinylpyrrolidone)-block-poly(d,l-lactide) (PVP-b-PDLLA) copolymer-based biodegradable and water soluble adhesive, that will help to retract the PET insertion tool after implantation. As a proof-of-concept of sub-system one, a microfabrication process for patterning PLA stiffeners embedded in parylene has been developed. Conventional hotembossing, mechanical micromachining, and standard cleanroom processes were integrated for patterning fully released and discrete stiffeners coated with parylene. The released embedded stiffeners were thermoformed to demonstrate that imparting perimodiolar shapes to stiffener-embedded arrays will be possible. The developed process when integrated with the array fabrication process will allow fabrication of stiffener-embedded arrays in a single process. As a proof-of-concept of sub-system two, the feasibility of the attaching and detaching mechanism was demonstrated by adhering 1x and 1.5x scale PET tube-based insertion tools and PLA stiffeners embedded in parylene using the copolymer adhesive. The attached devices survived qualitative adhesion tests, thermoforming, and flexing. The viability of the detaching mechanism was tested by aging the assemblies in-vitro in phosphate buffer solution. The average detachment times, 2.6 minutes and 10 minutes for 1x and 1.5x scale devices respectively, were found to be clinically relevant with respect to the reported array insertion times during surgical implantation. Eventually, the stiffener-embedded arrays would not need to be permanently attached to current insertion tools which are left behind after implantation and congest the cochlear scala tympani chamber. Finally, a simulation-based approach for accelerated failure analysis of PLA stiffeners and characterization of PVP-b-PDLLA copolymer adhesive has been explored. The residual functional life of embedded PLA stiffeners exposed to body-fluid and thereby subjected to degradation and erosion has been estimated by simulating PLA stiffeners with different parylene coating failure types and different PLA types for a given parylene coating failure type. For characterizing the PVP-b-PDLLA copolymer adhesive, several formulations of the copolymer adhesive were simulated and compared based on the insertion tool detachment times that were predicted from the dissolution, degradation, and erosion behavior of the simulated adhesive formulations. Results indicate that the simulation-based approaches could be used to reduce the total number of time consuming and expensive in-vitro tests that must be conducted.