Nova técnica para obtenção de fraturas com altíssima condutividade em poços de petróleo

Increase hydrocarbons production is the main goal of the oilwell industry worldwide. Hydraulic fracturing is often applied to achieve this goal due to a combination of attractive aspects including easiness and low operational costs associated with fast and highly economical response. Conventional fracturing usually involves high-flowing high-pressure pumping of a viscous fluid responsible for opening the fracture in the hydrocarbon producing rock. The thickness of the fracture should be enough to assure the penetration of the particles of a solid proppant into the rock. The proppant is driven into the target formation by a carrier fluid. After pumping, all fluids are filtered through the faces of the fracture and penetrate the rock. The proppant remains in the fracture holding it open and assuring high hydraulic conductivity. The present study proposes a different approach for hydraulic fracturing. Fractures with infinity conductivity are formed and used to further improve the production of highly permeable formations as well as to produce long fractures in naturally fractured formations. Naturally open fractures with infinite conductivity are usually encountered. They can be observed in rock outcrops and core plugs, or noticed by the total loss of circulation during drilling (even with low density fluids), image profiles, pumping tests (Mini-Frac and Mini Fall Off), and injection tests below fracturing pressure, whose flow is higher than expected for radial Darcian ones. Naturally occurring fractures are kept open by randomly shaped and placed supporting points, able to hold the faces of the fracture separate even under typical closing pressures. The approach presented herein generates infinite conductivity canal held open by artificially created parallel supporting areas positioned both horizontally and vertically. The size of these areas is designed to hold the permeable zones open supported by the impermeable areas. The England & Green equation was used to theoretically prove that the fracture can be held open by such artificially created set of horizontal parallel supporting areas. To assess the benefits of fractures characterized by infinite conductivity, an overall comparison with finite conductivity fractures was carried out using a series of parameters including fracture pressure loss and dimensionless conductivity as a function of flow production, FOI folds of increase, flow production and cumulative production as a function of time, and finally plots of net present value and productivity index

Pirólise rápida catalítica do capim elefante utilizando materiais mesoporosos e óxidos metálicos para deoxigenação em bio-óleo

The fast pyrolysis of lignocellulosic biomass is a thermochemical conversion process for production energy which have been very atratactive due to energetic use of its products: gas (CO, CO2, H2, CH4, etc.), liquid (bio-oil) and charcoal. The bio-oil is the main product of fast pyrolysis, and its final composition and characteristics is intrinsically related to quality of biomass (ash disposal, moisture, content of cellulose, hemicellulose and lignin) and efficiency removal of oxygen compounds that cause undesirable features such as increased viscosity, instability, corrosiveness and low calorific value. The oxygenates are originated in the conventional process of biomass pyrolysis, where the use of solid catalysts allows minimization of these products by improving the bio-oil quality. The present study aims to evaluate the products of catalytic pyrolysis of elephant grass (Pennisetum purpureum Schum) using solid catalysts as tungsten oxides, supported or not in mesoporous materials like MCM-41, derived silica from rice husk ash, aimed to reduce oxygenates produced in pyrolysis. The biomasss treatment by washing with heated water (CEL) or washing with acid solution (CELix) and application of tungsten catalysts on vapors from the pyrolysis process was designed to improve the pyrolysis products quality. Conventional and catalytic pyrolysis of biomass was performed in a micro-pyrolyzer, Py-5200, coupled to GC/MS. The synthesized catalysts were characterized by X ray diffraction, infrared spectroscopy, X ray fluorescence, temperature programmed reduction and thermogravimetric analysis. Kinetic studies applying the Flynn and Wall model were performed in order to evaluate the apparent activation energy of holoceluloce thermal decomposition on samples elephant grass (CE, CEL and CELix). The results show the effectiveness of the treatment process, reducing the ash content, and were also observed decrease in the apparent activation energy of these samples. The catalytic pyrolysis process converted most of the oxygenate componds in aromatics such as benzene, toluene, ethylbenzene, etc

Degradacao termica e catalitica da borra oleosa de Petroleo com materiais nanoestruturados al-mcm-41 e AL-SBA-15

Aiming to reduce and reuse waste oil from oily sludge generated in large volumes by the oil industry, types of nanostructured materials Al-MCM-41 and Al-SBA-15, with ratios of Si / Al = 50, were synthesized , and calcined solids used as catalysts in the degradation of oily sludge thermocatalytic oil from oilfield Canto do Amaro, in the state of Rio Grande do Norte. Samples of nanostructured materials were characterized by thermogravimetric analysis (TG / DTG), X-ray diffraction (XRD), scanning electron microscopy (SEM), absorption spectroscopy in the infrared Fourier transform (FT-IR) and adsorption nitrogen (BET). The characterization showed that the synthesized materials resulted in a catalyst nanostructure, and ordered pore diameter and surface area according to existing literature. The oily sludge sample was characterized by determining the API gravity and sulfur content and SARA analysis (saturates, aromatics, resins and asphaltenes). The results showed a material equivalent to the average oil with API gravity of 26.1, a low sulfur content and considerable amount of resins and asphaltenes, presented above in the literature. The thermal and catalytic degradation of the oily sludge oil was performed from room temperature to 870 ° C in the ratios of heating of 5, 10 and 20 ° C min-1. The curves generated by TG / DTG showed a more accelerated degradation of oily sludge when it introduced the nanostructured materials. These results were confirmed by activation energy calculated by the method of Flynn-Wall, in the presence of catalysts reduced energy, in particular in the range of cracking, showing the process efficiency, mainly for extraction of lightweight materials of composition of oily sludge, such as diesel and gasoline

Análise de viabilidade de injeção de fluidos alternativos ao vapor em reservatórios de óleo pesado

Many of hydrocarbon reserves existing in the world are formed by heavy oils (°API between 10 and 20). Moreover, several heavy oil fields are mature and, thus, offer great challenges for oil industry. Among the thermal methods used to recover these resources, steamflooding has been the main economically viable alternative. Latent heat carried by steam heats the reservoir, reducing oil viscosity and facilitating the production. This method has many variations and has been studied both theoretically and experimentally (in pilot projects and in full field applications). In order to increase oil recovery and reduce steam injection costs, the injection of alternative fluid has been used on three main ways: alternately, co-injected with steam and after steam injection interruption. The main objective of these injection systems is to reduce the amount of heat supplied to the reservoir, using cheaper fluids and maintaining the same oil production levels. This works discusses the use of carbon dioxide, nitrogen, methane and water as an alternative fluid to the steam. The analyzed parameters were oil recoveries and net cumulative oil productions. The reservoir simulation model corresponds to an oil reservoir of 100 m x 100 m x 28 m size, on a Cartesian coordinates system (x, y and z directions). It is a semi synthetic model with some reservoir data similar to those found in Brazilian Potiguar Basin. All studied cases were done using the simulator STARS from CMG (Computer Modelling Group, version 2009.10). It was found that waterflood after steam injection interruption achieved the highest net cumulative oil compared to other fluids injection. Moreover, it was observed that steam and alternative fluids, co-injected and alternately, did not present increase on profitability project compared with steamflooding

Análise paramétrica da injeção de vapor e solvente em reservatórios de óleo pesado

A significant fraction of the hydrocarbon reserves in the world is formed by heavy oils. From the thermal methods used to recovery these resources, Steamflooding has been one of the main economically viable alternatives. In Brazil, this technology is widely used by Petrobras in Northeast fields. Latent heat carried by steam heats the oil in the reservoir, reducing its viscosity and facilitating the production. In the last years, an alternative more and more used by the oil industry to increase the efficiency of this mechanism has been the addition of solvents. When co-injected with steam, the vaporized solvent condenses in the cooler regions of the reservoir and mixes with the oil, creating a low viscosity zone between the steam and the heavy oil. The mobility of the displaced fluid is then improved, resulting in an increase of oil recovery. To better understand this improved oil recovery method and investigate its applicability in reservoirs with properties similar to those found in Potiguar Basin, a numerical study was done to analyze the influence of some operational parameters (steam injection rate, injected solvent volume and solvent type) on oil recovery. Simulations were performed in STARS ("Steam, Thermal, and Advanced Processes Reservoir Simulator"), a CMG ("Computer Modelling Group") program, version 2009.10. It was found that solvents addition to the injected steam not only anticipated the heated oil bank arrival to the producer well, but also increased the oil recovery. Lower cold water equivalent volumes were required to achieve the same oil recoveries from the models that injected only steam. Furthermore, much of the injected solvent was produced with the oil from the reservoir

Pirólise de borras oleosas de petroleo utilizando nanomateriais

The oily sludge is a complex mix of hydrocarbons, organic impurities, inorganic and water. One of the major problems currently found in petroleum industry is management (packaging, storage, transport and fate) of waste. The nanomaterials (catalysts) mesoporous and microporous are considered promising for refining and adsorbents process for environment protection. The aim of this work was to study the oily sludge from primary processing (raw and treated) and vacuum residue, with application of thermal analyses technique (pyrolysis), thermal and catalytic pyrolysis with nanomaterials, aiming at production petroleum derived. The sludge and vacuum residue were analyzed using a soxhlet extraction system, elemental analysis, thin layer chromatography, thermogravimetry and pyrolysis coupled in gas chromatography/mass spectrometry (Py GC MS). The catalysts AlMCM-41, AlSBA-15.1 e AlSBA-15.2 were synthesized with molar ratio silicon aluminum of 50 (Si/Al = 50), using tetraethylorthosilicante as source of silicon and pseudobuhemita (AlOOH) as source of aluminum. The analyzes of the catalysts indicate that materials showed hexagonal structure and surface area (783,6 m2/g for AlMCM-41, 600 m2/g for AlSBA-15.1, 377 m2/g for AlSBA-15.2). The extracted oily sludge showed a range 65 to 95% for organic components (oil), 5 to 35% for inorganic components (salts and oxides) and compositions different of derivatives. The AlSBA-15 catalysts showed better performance in analyzes for production petroleum derived, 20% increase in production of kerosene and light gas oil. The energy potential of sludge was high and it can be used as fuel in other cargo processed in refinery

Evaluación de la exposición laboral a material particulado en empresas pertenecientes a diferentes sectores económicos en Colombia, 2014

Introducción El material particulado son partículas sólidas y líquidas emitidas al aire, las cuales pueden generar diferentes alteraciones en la salud, variando desde cuadros respiratorios alérgicos, a episodios asmáticos, dermatitis o inclusive llegar a facilitar la génesis de enfermedades de tipo neoplásico. Estos pueden tener origen natural e industrial, encontrandose en diferentes actividades económicas. Objetivo Evaluar la exposición laboral a material particulado en empresas pertenecientes a diferentes sectores económicos afiliadas a una ARL en Colombia, en el periodo comprendido entre 2011 al 2014 Metodología Es un estudio de corte transversal, analizando una base de datos de 257 empresas con 1108 mediciones de material particulado, recolectados entre 2011 – 2014. Las variables usadas fueron: región, actividad económica, área, oficio, tiempo de exposición y concentración de material particulado. Se realizó distribuciones de frecuencia, medidas de tendencia central y de dispersión. Se evaluaron las diferencias de las distribuciones de los tiempos de exposición y el porcentaje de exposición entre los grupos con y sin riesgo (los que sobrepasaban o no los límites permisibles), con la prueba asintótica no paramétrica de Mann Whitney. Resultados Las principales mediciones ambientales en las empresas fueron en la industria química con un 31%, siendo 2 de cada 3 datos pertenecientes a la región andina, las cuales tienen como principales contaminantes químicos las partículas no fraccionadas con el 70,9%. Respecto a las concentraciones ambientales de material particulado en las empresas participantes, se encontró un promedio de 1,72 mg/m3 ± 3,613, con una mediana de 0,480 mg/m3 y un coeficiente de variación de 210,05%. El 2,9% sobrepasaron los valores límites establecidos por la ACGIH (American Conference of Governmental Industrial Hygienists) y el 92,5% según los límites de la EPA (Agencia de Protección del Ambiente), presentando mayor riesgo en el personal operativo con 93,3% (p= 0,002). Conclusión El riesgo según los límites establecidos por la ACGIH para las mediciones realizadas en Colombia fue bajo, aunque al utilizar los parámetros de la EPA, el riesgo fue alto, por lo cual se requiere hacer un seguimiento específico a estas empresas y fomentar la implementación del sistema de gestión en seguridad y salud en el trabajo.

Remediação do solo e da água: aspectos gerais.

Historicamente, o solo tem sido utilizado por gerações como receptor de substâncias resultantes da atividade humana. A partir da Revolução Industrial, a liberação descontrolada de poluentes para o ambiente e sua consequente acumulação no solo e nos aquíferos sofreu uma mudança drástica de forma e de intensidade, explicada pelo aumento do volume e dos tipos de resíduos gerados pelas atividades urbanas, industriais e agrícolas. Dentro deste contexto, o estudo das interações de diversos tipos de poluentes inorgânicos e orgânicos em solos, como forma de mitigar sua acumulação e possível impacto sobre a biota e as águas subterrâneas é fundamental.

Microbiologia ambiental.

Impacto de mudanças climáticas globais sobre a microbiota terrestre - Raquel Ghini. Impacto de xenobióticos e metais pesados na microbiota do solo - Célia Maria Maganhotto de Souza Silva e Rosana Faria Vieira. Microrganismos, minerais e metais - Oswaldo Garcia Jr. e Denise Bevilaqua. Bioprospecção da diversidade microbiana cultivável e não cultivável - Raquel Silva Peixoto, Alexandre Soares Rosado e Rodrigo Gouvêa Taketani. Técnicas moleculares aplicadas aos estudos de ecologia microbiana: A PCR em tempo real - Paulo Teixeira Lacava e João Lúcio de Azevedo. Biofilmes microbianos - René P Schneider. Biossurfactantes - Fátima Menezes Bento, Flavio A. de Oliveira Camargo e Christine Claire Gaylarde. Importância ambiental da biocatálise - Viridiana Santana Ferreira-Leitão, Maria Antonieta Ferrara e Elba P S. Bom. Estratégias de isolamento de microrganismos envolvidos na degradação de xenobióticos - Itamar Soares de Melo e João Lúcio de Azevedo. Biodegradação anaeróbia - Rosana Filomena Vazoller, Márcia Helena Rissato Zamariolli Damianovic e Juliana Calábria Araújo. Biodegradação de compostos aromáticos - Aneli de Melo Barbosa, Ellen Cristine Giese e Luiz Gustavo Covizzi. Biodegradação de organoclorados no solo por basidiomicetos lignovelulolíticos - Vera Lúcia Ramos Bonomi, Kátia Maria Gomes Machado, Dácio Roberto Mateus e Vera Maria Vitali. Biodegradação de lignina e tratamento de efluentes por fungos ligninolíticos: atualização - Nelson Durán e Elisa Esposito. Biodegradação de corantes têxteis - Priscila Maria Dellamatrice, Regina Teresa Rosim Monteiro e Doralice de Souza Luro Balan. Biodegradação de superfícies pintadas - Denise de Souza Saad. Biodegradação de polímeros sintéticos - Sandra Mara Martins Franchetti, José Carlos Marconato e Adriana de Campos. Biodegradação de fungicidas - Célia Maria Maganhotto de Souza Silva, Elisabeth Francisconi Fay e Rosângela Blotta Abakerli. Biodegradação de monoterpenos - Lucia Regina Durrant. Degradação de cafeína por bactérias - Paulo Mazzafera e Dirce Mithico Yamaoka-Yano. Degradação abiótica de xenobióticos - Elisabeth Francisconi Fay, Célia Maria Maganhotto de Souza Silva e Itamar Soares de Melo. Biodeterioração no ambiente construído - Márcia A. Shirakawa, Vanderley M. John e Maria Alba Cincotto. Biodeterioração de monumentos históricos - Maria Aparecida de Resende. Biodeterioração de monumentos históricos - Maria Aparecida de Resende. Biorremediação de solos contaminados por petróleo e derivados - Paulo Negrais Seabra. Fitorremediação de metais - Marcia Pletsch, Á ndrea C. A. Barros e Brancilene S. de Araujo. Importância da rizosfera na biodegradação de xenobióticos - Itamar Soares de Melo. Microbiologia aquática marinha - Irnia Nelly G. Rivera, Claudete Rodrigues Paula e Claudiana Paula de Souza. Transferência horizontal de genes de plantas geneticamente modificadas: avaliação dos riscos para as comunidades microbianas - Welington Luiz Araújo, Priscilla de Barros Rossetto e Júlia Ifuklinsky-Sobral.