Potential for Greenhouse Gas Emission Reductions by Using Biomethane as a Road Transportation Fuel

The aim of this thesis is to study whether the use of biomethane as a transportation fuel is reasonable from climate change perspective. In order to identify potentials and challenges for the reduction of greenhouse gas (GHG) emissions, this dissertation focuses on GHG emission comparisons, on feasibility studies and on the effects of various calculation methodologies. The GHG emissions calculations are carried out by using life cycle assessment (LCA) methodologies. The aim of these LCA studies is to figure out the key parameters affecting the GHG emission saving potential of biomethane production and use and to give recommendations related to methodological choices. The feasibility studies are also carried out from the life cycle perspective by dividing the biomethane production chain for various operators along the life cycle of biomethane in order to recognize economic bottlenecks. Biomethane use in the transportation sector leads to GHG emission reductions compared to fossil transportation fuels in most cases. In addition, electricity and heat production from landfill gas, biogas or biomethane leads to GHG reductions as well. Electricity production for electric vehicles is also a potential route to direct biogas or biomethane energy to transportation sector. However, various factors along the life cycle of biomethane affect the GHG reduction potentials. Furthermore, the methodological selections have significant effects on the results. From economic perspective, there are factors related to different operators along the life cycle of biomethane, which are not encouraging biomethane use in the transportation sector. To minimize the greenhouse gas emissions from the life cycle of biomethane, waste feedstock should be preferred. In addition, energy consumption, methane leakages, digestate utilization and the current use of feedstock or biogas are also key factors. To increase the use of biomethane in the transportation sector, political steering is needed to improve the feasibility for the operators. From methodological perspective, it is important to recognize the aim of the life cycle assessment study. The life cycle assessment studies can be divided into two categories: 1.) To produce average GHG information of biomethane to evaluate the acceptability of biomethane use compared to fossil transportation fuels. 2.) To produce GHG information of biomethane related to actual decision-making situations. This helps to figure out the actual GHG emission changes in cases when feedstock, biogas or biomethane are already in other use. For example directing biogas from electricity production to transportation use does not necessarily lead to additional GHG emission reductions. The use of biomethane seems to have a lot of potential for the reduction of greenhouse gas emissions as a transportation fuel. However, there are various aspects related to production processes, to the current use of feedstock or biogas and to the feasibility that have to be taken into account.

Application and development of numerical methods for the modelling of innovative gas cooled fission reactors

Innovative gas cooled reactors, such as the pebble bed reactor (PBR) and the gas cooled fast reactor (GFR) offer higher efficiency and new application areas for nuclear energy. Numerical methods were applied and developed to analyse the specific features of these reactor types with fully three dimensional calculation models. In the first part of this thesis, discrete element method (DEM) was used for a physically realistic modelling of the packing of fuel pebbles in PBR geometries and methods were developed for utilising the DEM results in subsequent reactor physics and thermal-hydraulics calculations. In the second part, the flow and heat transfer for a single gas cooled fuel rod of a GFR were investigated with computational fluid dynamics (CFD) methods. An in-house DEM implementation was validated and used for packing simulations, in which the effect of several parameters on the resulting average packing density was investigated. The restitution coefficient was found out to have the most significant effect. The results can be utilised in further work to obtain a pebble bed with a specific packing density. The packing structures of selected pebble beds were also analysed in detail and local variations in the packing density were observed, which should be taken into account especially in the reactor core thermal-hydraulic analyses. Two open source DEM codes were used to produce stochastic pebble bed configurations to add realism and improve the accuracy of criticality calculations performed with the Monte Carlo reactor physics code Serpent. Russian ASTRA criticality experiments were calculated. Pebble beds corresponding to the experimental specifications within measurement uncertainties were produced in DEM simulations and successfully exported into the subsequent reactor physics analysis. With the developed approach, two typical issues in Monte Carlo reactor physics calculations of pebble bed geometries were avoided. A novel method was developed and implemented as a MATLAB code to calculate porosities in the cells of a CFD calculation mesh constructed over a pebble bed obtained from DEM simulations. The code was further developed to distribute power and temperature data accurately between discrete based reactor physics and continuum based thermal-hydraulics models to enable coupled reactor core calculations. The developed method was also found useful for analysing sphere packings in general. CFD calculations were performed to investigate the pressure losses and heat transfer in three dimensional air cooled smooth and rib roughened rod geometries, housed inside a hexagonal flow channel representing a sub-channel of a single fuel rod of a GFR. The CFD geometry represented the test section of the L-STAR experimental facility at Karlsruhe Institute of Technology and the calculation results were compared to the corresponding experimental results. Knowledge was gained of the adequacy of various turbulence models and of the modelling requirements and issues related to the specific application. The obtained pressure loss results were in a relatively good agreement with the experimental data. Heat transfer in the smooth rod geometry was somewhat under predicted, which can partly be explained by unaccounted heat losses and uncertainties. In the rib roughened geometry heat transfer was severely under predicted by the used realisable k − epsilon turbulence model. An additional calculation with a v2 − f turbulence model showed significant improvement in the heat transfer results, which is most likely due to the better performance of the model in separated flow problems. Further investigations are suggested before using CFD to make conclusions of the heat transfer performance of rib roughened GFR fuel rod geometries. It is suggested that the viewpoints of numerical modelling are included in the planning of experiments to ease the challenging model construction and simulations and to avoid introducing additional sources of uncertainties. To facilitate the use of advanced calculation approaches, multi-physical aspects in experiments should also be considered and documented in a reasonable detail.

Thermal reactions of the major hydrocarbon components of biomass gasification gas

Gasification of biomass is an efficient method process to produce liquid fuels, heat and electricity. It is interesting especially for the Nordic countries, where raw material for the processes is readily available. The thermal reactions of light hydrocarbons are a major challenge for industrial applications. At elevated temperatures, light hydrocarbons react spontaneously to form higher molecular weight compounds. In this thesis, this phenomenon was studied by literature survey, experimental work and modeling effort. The literature survey revealed that the change in tar composition is likely caused by the kinetic entropy. The role of the surface material is deemed to be an important factor in the reactivity of the system. The experimental results were in accordance with previous publications on the subject. The novelty of the experimental work lies in the used time interval for measurements combined with an industrially relevant temperature interval. The aspects which are covered in the modeling include screening of possible numerical approaches, testing of optimization methods and kinetic modelling. No significant numerical issues were observed, so the used calculation routines are adequate for the task. Evolutionary algorithms gave a better performance combined with better fit than the conventional iterative methods such as Simplex and Levenberg-Marquardt methods. Three models were fitted on experimental data. The LLNL model was used as a reference model to which two other models were compared. A compact model which included all the observed species was developed. The parameter estimation performed on that model gave slightly impaired fit to experimental data than LLNL model, but the difference was barely significant. The third tested model concentrated on the decomposition of hydrocarbons and included a theoretical description of the formation of carbon layer on the reactor walls. The fit to experimental data was extremely good. Based on the simulation results and literature findings, it is likely that the surface coverage of carbonaceous deposits is a major factor in thermal reactions.

Family ownership – a source of sustainable success in listed companies

Extant research on exchange-listed firms has acknowledged that the concentration of ownership and the identity of owners make a difference. In addition, studies indicate that firms with a dominant owner outperform firms with dispersed ownership. During the last few years, scholars have identified one group of owners, in particular, whose ownership stake in publicly listed firm is positively related to performance: the business family. While acknowledging that family firms represent a unique organizational form, scholars have identified various concepts and theories in order to understand how the family influences organizational processes and firm performance. Despite multitude of research, scholars have not been able to present clear results on how firm performance is actually impacted by the family. In other words, studies comparing the performance of listed family and other types of firms have remained descriptive in nature since they lack empirical data and confirmation from the family business representatives. What seems to be missing is a convincing theory that links the involvement and behavioral consequences. Accordingly, scholars have not yet come to a mutual understanding of what precisely constitutes a family business. The variety of different definitions and theories has made comparability of different results difficult for instance. These two issues have hampered the development of a rigorous theory of family business. The overall objective of this study is to describe and understand how the family as a dominant owner can enhance firm performance, and can act a source of sustainable success in listed companies. In more detail, in order to develop understanding of the unique factors that can act as competitive advantages for listed family firms, this study is based on a qualitative approach and aims at theory development, not theory verification. The data in this study consist of 16 thematic interviews with CEOs, members of the board, supervisory board chairs, and founders of Finnish listed-family firms. The study consists of two parts. The first part introduces the research topic, research paradigm, methods, and publications, and also discusses the overall outcomes and contributions of the publications. The second part consists of four publications that address the research questions from different viewpoints. The analyses of this study indicate that family ownership in listed companies represents a structure that differs from the traditional views of agency and stewardship, as well as from resource-based and stakeholder views. As opposed to these theories and shareholder capitalism which consider humans as individualistic, opportunistic, and self-serving, and assume that the behaviors of an investor are based on the incentives and motivations to maximize private profits, the family owners form a collective social unit that is motivated to act together toward their mutual purpose or benefit. In addition, socio-emotional and psychological elements of ownership define the family members as owners, rather than the legal and financial dimensions of ownership. That is, collective psychological ownership of family over the business (F-CPO) can be seen as a construct that comprehensively captures the fusion between the family and the business. Moreover, it captures the realized, rather than merely potential, family influence on and interaction with the business, and thereby brings more theoretical clarity of the nature of the fusion between the family and the business, and offers a solution to the problem of family business definition. This doctoral dissertation provides academics, policy-makers, family business practitioners, and the society at large with many implications considering family and business relationships.

Comparison of the quantification of caffeine in human plasma by gas chromatography and ELISA

In the present study we evaluated the precision of the ELISA method to quantify caffeine in human plasma and compared the results with those obtained by gas chromatography. A total of 58 samples were analyzed by gas chromatography using a nitrogen-phosphorus detector and routine techniques. For the ELISA test, the samples were diluted to obtain a concentration corresponding to 50% of the absorbance of the standard curve. To determine whether the proximity between the I50 of the standard curve and that of the sample would bring about a more precise result, the samples were divided into three blocks according to the criterion of difference, in modulus, of the I50 of the standard curve and of the I50 of the sample. The samples were classified into three groups. The first was composed of 20 samples with I50 up to 1.5 ng/ml, the second consisted of 21 samples with I50 ranging from 1.51 to 3 ng/ml, and the third of 17 samples with I50 ranging from 3.01 to 13 ng/ml. The determination coefficient (R² = 0.999) showed that the data obtained by gas chromatography represented a reliable basis. The results obtained by ELISA were also reliable, with an estimated Pearson correlation coefficient of 0.82 between the two methods. This coefficient for the different groups (0.88, 0.79 and 0.49 for groups 1, 2 and 3, respectively) showed greater reliability for the test with dilutions closer to I50.

A geological and topographical sketch map of the New York and Westmoreland Gas Coal Company's lands, at Manor Sta., Westm'd Co., Pa.

Kartta kuuluu A. E. Nordenskiöldin kokoelmaan

The Possibility of Greenhouse Gas Mitigation in Ethiopian Cement Industry

Cement industry significantly associated with high greenhouse gas (GHG) emissions. Considering the environmental impact, particularly global warming potential, it is important to reduce these emissions to air. The aim of the study is to investigate the mitigation possibility of GHG emissions in Ethiopian cement industry. Life cycle assessment (LCA) method used to identify and quantify GHG emissions during one ton of ordinary portland cement (OPC) production. Three mitigation scenarios: alternative fuel use, clinker substitution and thermal energy efficiency were applied on a representative gate-to-gate flow model developed with GaBi 6 software. The results of the study indicate that clinker substitution and alternative fuel use play a great role for GHG emissions mitigation with affordable cost. Applying most energy efficient kiln technology, which in turn reduces the amount of thermal energy use, has the least GHG emissions reduction intensity and high implementation cost comparing to the other scenarios. It was found that the cumulative GHG emissions mitigation potential along with other selected mitigation scenarios can be at least 48.9% per ton of cement production.

Modeling Front End Electronics for a Gas Electron Multiplier Detector

The Large Hadron Collider (LHC) in The European Organization for Nuclear Research (CERN) will have a Long Shutdown sometime during 2017 or 2018. During this time there will be maintenance and a possibility to install new detectors. After the shutdown the LHC will have a higher luminosity. A promising new type of detector for this high luminosity phase is a Triple-GEM detector. During the shutdown these detectors will be installed at the Compact Muon Solenoid (CMS) experiment. The Triple-GEM detectors are now being developed at CERN and alongside also a readout ASIC chip for the detector. In this thesis a simulation model was developed for the ASICs analog front end. The model will help to carry out more extensive simulations and also simulate the whole chip before the whole design is finished. The proper functioning of the model was tested with simulations, which are also presented in the thesis.

Predicting bankruptcy of Finnish limited liability companies from historical financial statements

This master’s thesis studies the probability of bankruptcy of Finnish limited liability companies as a part of credit risk assessment. The main idea of this thesis is to build and test bankruptcy prediction models for Finnish limited liability companies that can be utilized in credit decision making. The data used in this thesis consists of historical financial statements from 2112 Finnish limited liability companies, half of which have filed for bankruptcy. A total of four models are developed, two with logistic regression and two with multivariate discriminant analysis (MDA). The time horizon of the models varies from 1 to 2 years prior to the bankruptcy, and 14 different financial variables are used in the model formation. The results show that the prediction accuracy of the models ranges between 81.7% and 88.9%, and the best prediction accuracy is achieved with the one year prior the bankruptcy logistic regression model. However the difference between the best logistic model and the best MDA model is minimal. Overall based on the results of this thesis it can be concluded that predicting bankruptcy is possible to some extent, but naturally the results are not perfect.

The biological effects of high-pressure gas on the yeast transcriptome

The aim of the present study was to examine the feasibility of DNA microarray technology in an attempt to construct an evaluation system for determining gas toxicity using high-pressure conditions, as it is well known that pressure increases the concentration of a gas. As a first step, we used yeast (Saccharomyces cerevisiae) as the indicator organism and analyzed the mRNA expression profiles after exposure of yeast cells to nitrogen gas. Nitrogen gas was selected as a negative control since this gas has low toxicity. Yeast DNA microarray analysis revealed induction of genes whose products were localized to the membranes, and of genes that are involved in or contribute to energy production. Furthermore, we found that nitrogen gas significantly affected the transport system in the cells. Interestingly, nitrogen gas also resulted in induction of cold-shock responsive genes. These results suggest the possibility of applying yeast DNA microarray to gas bioassays up to 40 MPa. We therefore think that "bioassays" are ideal for use in environmental control and protection studies.

Potential for synthetic gas in Finnish industry

Finland, other Nordic countries and European Union aim to decarbonize their energy production by 2050. Decarbonization requires large scale implementation of non-emission energy sources, i.e. renewable energy and nuclear power. Stochastic renewable energy sources present a challenge to balance the supply and demand for energy. Energy storages, non-emissions fuels in mobility and industrial processes are required whenever electrification is not possible. Neo-Carbon project studies the decarbonizing the energy production and the role of synthetic gas in it. This thesis studies the industrial processes in steel production, oil refining, cement manufacturing and glass manufacturing, where natural gas is already used or fuel switch to SNG is possible. The technical potential for fuel switching is assessed, and economic potential is necessary after this. All studied processes have potential for fuel switching, but total decarbonization of steel production, oil refining requires implementation of other zero-emission technologies.

Lean Innovation in Large Companies: a Case of Implementation in R&D

The main objective of the study is to evaluate the impact of Lean Innovation management philosophy on the creativity potential of the large multinational enterprise. A theory of Lean Innovation indicates that the modern company in any industry can successfully combine both waste-decreasing approach and innovative potential promotion through creativity cultivation or, at least, preservation. The theoretical part of the work covers the main factors, pros and cons of Lean thinking and Innovation management separately, along with generalized new product development overview. While the modern international market becomes more accessible for entrepreneural initiatives, small enterprises and start-ups, large international corporations are more subject to adopt the Lean Innovation approach in both operational and product development sectors due to extended resources and capabilities. Moreover, a multinational enterprise is a highly probable pioneer in Lean innovation implementation. The empirical part of the thesis refers to a case of large European enterprise, operating in many markets around the globe, that currently undergoes innovation management adjustments and implementations in product development while already have related themselves with operational process optimization process through Lean thinking. A goal of the work is to understand what kind of difficulties and consequences a large international firm faces when dealing with Lean Innovation to improve own performance, if they can be sealed for generalized approach.

MARKETING COMMUNICATIONS IN B2B COMPANIES – The Roles of Marketing Communication Tools in the Digital Age

Marketing communications has gone through significant changes during the last decades and new online tools have been leading this change for the last decade. Now, in the digital age, if wanting to be successful companies need to experiment new things and seize the opportunities online provides and adapt to the new environment. However, during this time the marketing communication mix and the meanings given to the various components of it have not changed dramatically, and personal selling, direct marketing, sales promotion, advertising and public relations activities are still regarded as important tools in the marketing communications mix. The purpose of this study was to examine business-to-business marketing communications and the tools used by companies in their marketing communications efforts in the digital age and in a global environment. The research questions dealt with the marketing communication tools and their roles as well as the role of online marketing communication and the way it has shaped the field of b2b marketing communications. In order to answer these questions, qualitative approach was chosen and the data was collected by theme interviews with six representatives of Finnish global companies from the b2b sector being interviewed. The theoretical framework covers the general field of b2b marketing communications and its main elements. The online environment as well as the concept of a global marketplace and integrated approach to marketing communication activities is also discussed. The theory was supported by the interviews regarding the activities and roles of the marketing communication tools and both theory as well as the interviews found personal selling to be a vital tool. However, the importance of online has grown and online marketing activities have risen right next to personal selling. The use of analytics and marketing automation was found to be of great interest in the interviews and they were seen as a growing domain in b2b marketing communications. The importance of targeted and personalised messages from relevant medias was a repeating theme as was the customer-centric approach in marketing communication activities. Also, offline and online tools and channels were seen as something that should be treated together as an entity rather than as separate activities. Relevant content created according to the needs of the customer with the gathered data from analytics were seen as the future of b2b marketing communications. Online has added its input to the more traditionally perceived tools and they are executed within the framework of the digital age. Nevertheless, even though online has increased its presence in the b2b marketing communications mix, the more traditionally perceived marketing communication tools, especially personal selling, have not lost their meaning or place in the b2b marketing communication mix.

Integrating corporate social responsibility into business in Finnish consumer goods companies

The motives for this study originated from the notion that surprisingly little academic literature is found on actually managing and putting corporate social responsibility (CSR) into practice, in comparison with the definitions and frameworks of the concept itself. Regardless of the author, CSR has been considered consisting of three dimensions: economic, social and environmental. The question behind the three dimensions has always been whether socially and environmentally responsible behavior can lead to increased economic performance and improve the competitiveness of a company. Most of the current CSR development has related to the quantification of environmental and social performance in order to review these along with the established financial key ratios, which are based on the law and the reporting obligation of the companies. However, the previous research has mainly focused on US companies whereas studies with a European viewpoint, let alone Nordic, have been mostly lacking. Furthermore, it has been discovered recently that the integration of corporate responsibility into business is identified as the greatest challenge in CSR management in Finnish large companies. Therefore the integration of CSR into business in Finnish consumer goods companies provided an interesting, topical and somewhat obscure purpose for this study. This was further divided into three research questions concerning the reasons for CSR engagement, the role of the stakeholders and the practice of corporate responsibility. This study did not aim to build a new theory; instead an explorative viewpoint was regarded more appropriate. Accordingly, qualitative research approach and case study design were adopted in the study. Semi-structured theme interviews were used as a primary data collection method and complemented with secondary data such as websites, responsibility reports and another recent CSR study. There were four Finnish managers as interviewees of whom three presented companies and one non-profit organization. The results were somewhat convergent but differences arose as a result of the companies being at different stages as regards corporate responsibility. However, this provided only more insight into the implementation of CSR. The voluntary CSR initiatives, responsibility reporting, stakeholders and CSR management were identified as the most important viewpoints on the practical side of CSR, besides a key requirement for the integration of CSR into business to be credible was found to be a favorable management attitude. Based on the findings of this study it was admitted that giving concrete advice on CSR management is really a challenge and there is no one generally accepted and right manner to integrate corporate responsibility successfully into business.

Mechanisms underlying gas exchange alterations in an experimental model of pulmonary embolism

The aim of the present study was to determine the ventilation/perfusion ratio that contributes to hypoxemia in pulmonary embolism by analyzing blood gases and volumetric capnography in a model of experimental acute pulmonary embolism. Pulmonary embolization with autologous blood clots was induced in seven pigs weighing 24.00 ± 0.6 kg, anesthetized and mechanically ventilated. Significant changes occurred from baseline to 20 min after embolization, such as reduction in oxygen partial pressures in arterial blood (from 87.71 ± 8.64 to 39.14 ± 6.77 mmHg) and alveolar air (from 92.97 ± 2.14 to 63.91 ± 8.27 mmHg). The effective alveolar ventilation exhibited a significant reduction (from 199.62 ± 42.01 to 84.34 ± 44.13) consistent with the fall in alveolar gas volume that effectively participated in gas exchange. The relation between the alveolar ventilation that effectively participated in gas exchange and cardiac output (V Aeff/Q ratio) also presented a significant reduction after embolization (from 0.96 ± 0.34 to 0.33 ± 0.17 fraction). The carbon dioxide partial pressure increased significantly in arterial blood (from 37.51 ± 1.71 to 60.76 ± 6.62 mmHg), but decreased significantly in exhaled air at the end of the respiratory cycle (from 35.57 ± 1.22 to 23.15 ± 8.24 mmHg). Exhaled air at the end of the respiratory cycle returned to baseline values 40 min after embolism. The arterial to alveolar carbon dioxide gradient increased significantly (from 1.94 ± 1.36 to 37.61 ± 12.79 mmHg), as also did the calculated alveolar (from 56.38 ± 22.47 to 178.09 ± 37.46 mL) and physiological (from 0.37 ± 0.05 to 0.75 ± 0.10 fraction) dead spaces. Based on our data, we conclude that the severe arterial hypoxemia observed in this experimental model may be attributed to the reduction of the V Aeff/Q ratio. We were also able to demonstrate that V Aeff/Q progressively improves after embolization, a fact attributed to the alveolar ventilation redistribution induced by hypocapnic bronchoconstriction.