923 resultados para FERROMAGNETIC MONOLAYER FE(110)
Resumo:
Neste trabalho foram estudadas as propriedades magnéticas e estruturais de filmes ultrafinos de Fe, Co e Ni produzidos por eletrodeposição sobre substratos de Au(111). Os estágios iniciais de crescimento dos filmes foram estudados por técnicas de caracterização “in-situ”. Uma nova técnica de caracterização do estado magnético de filmes ultrafinos eletrodepositados (EC-AGFM) foi utilizada, mostrando-se uma poderosa ferramenta para o estudo das propriedades magnéticas dos filmes. Outras técnicas, como STM “in-situ”, PMOKE “in-situ”, EXAFS, XRD, RBS foram utilizadas. A análise dos dados revelaram resultados diferentes para os filmes de Fe e Co/Au(111), em comparação aos filmes de Ni/Au(111). Enquanto a anisotropia magnética perpendicular (PMA) foi observada para os filmes de Fe e Co/Au(111), não foi observada para os filmes de Ni/Au(111). Os resultados são interpretados em termos das contribuições para a anisotropia magnética dos filmes. No caso do níquel, a degradação de suas propriedades magnéticas são atribuídas à incorporação de hidrogênio durante a deposição. Os resultados das análises magnética e estrutural são correlacionados a fim de compreender o comportamento das propriedades observadas. Os resultados são comparados aos obtidos por técnicas em vácuo.
Resumo:
Neste trabalho foram estudadas as propriedades morfológicas, estruturais e magnéticas de nanoestruturas de Fe crescidas em Si(111) vicinal. A análise de superfície foi feita usando microscopia de força atômica e microscopia de tunelamento, e as medidas de caracterização estrutural, por espectroscopia de absorção de raios-X. As propriedades magnéticas foram investigadas usando dois métodos distintos: efeito Kerr magneto-óptico e magnetômetro de força de gradiente alternado. Os substratos foram preparados quimicamente com uma solução NH4F e caracterizados por microscopia de força atômica. As análises morfológicas das superfícies permitiram classificá-las em dois grupos: Si(111)- monoatômicos e Si(111)-poliatômicos. Filmes finos de ferro de 1.5, 3, 6 e 12 nm foram crescidos sobre eles. A análise das superfícies indicou dois modos diferentes de crescimento do ferro; o sistema Fe(x)Si(111)-monoatômico resulta em grãos de ferro aleatoriamente distribuídos, e o sistema Fe(x)Si(111)-poliatômico em nanogrãos de ferro alongados na direção perpendicular aos degraus, auto-organizados. Particularmente no filme Fe(3 nm)/Si(111)-poliatômico, ao redor de metade dos grãos estão alinhados ao longo da direção [110] , ou seja, paralelo aos degraus. O padrão de nanogrãos de ferro alongados orientados perpendicular aos degraus foi interpretado com uma conseqüência da anisotropia induzida durante o processo de deposição e a topologia do substrato Si(111)-poliatômico. Uma forte relação entre a morfologia e a resposta magnética dos filmes foi encontrada. Um modelo fenomenológico foi utilizado para interpretar os dados experimentais da magnetização, e uma excelente concordância entre as curvas experimentais e calculadas foi obtida.
Resumo:
O objetivo desta tese é investigar cuidadosamente a interação entre a intuição e a razão, propondo um novo modelo cognitivo que explicaria a existência, interação e comportamento dos chamados "dois sistemas" que, supõe-se, coabitem a mente humana. O modelo que será postulado nesta dissertação integra e explica estes dois sistemas; e o sistema NUMBO derivado dos projetos de Hofstadter (1995) é capaz de demonstrar sua plausibilidade psicológica e sua tàctibilidade de modelagem e simulação em uma arquitetura computacional. Serão utilizadas variações do problema da bola e do taco, pertencente ao Cognitive Reflection Test proposto por Frederick (2005), para ilustrar como o processo pelo qual as pessoas passam pode se dar, bem como serão utilizados resultados da psicologia experimental, para validar a plausibilidade psicológica dos mecanismos propostos. A contribuição deste trabalho é, portanto, explicitar as "coleções de processos" que estão operando em cada "caixa-preta" do sistema 1 ou sistema 2. Desta fom1a, pretende-se dar um pequeno passo em direção à teorias mais elaboradas sobre intuição e razão.
Resumo:
Inorganic pigment comprises a host lattice, which is part of the chromophore component (usually a transition metal cation) and possible components modifiers, which stabilize, add or restate the properties pigments. Among the materials with spinel, ferrites, and the chromite stand out, because they have broad technological importance in the area of materials, applicability, pigments, catalytic hydrogenation, thin film, ceramic tiles, among others. The present work, pigments containing CuFe2O4, CuCr2O4,e CuFeCrO4, were synthesized by a method that makes use of gelatin as organic precursor using their application to ceramic pigments. The pigments were characterized by X-ray diffraction (XRD), Infrared spectroscopy, scanning electron microscopy (SEM) spectroscopy in the UV-visible and Colorimetry. The results confirmed the feasibility of the synthetic route used, with respect to powders synthesized, there is the formation of spinel phase from 500°C, with an increase in crystallinity and the formation of other phases. The pigments were shown to be crystalline and the desired phases were obtained. The copper chromite have hues ranging from green to black according to the calcination temperature, while the copper chromite doped with iron had brownish. The ferrites showed copper color and darker brown to black, which may indicate an interesting factor because of the importance of black pigment
Resumo:
Microalloyed steels constitute a specific class of steel with low amount of carbon and microalloying elements such as Vanadium (V), Niobium (Nb) and Titanium (Ti). The development and application of microalloyed steels and steels in general are limited to the handling of powders with particles of submicron or nanometer dimensions. Therefore, this work presents an alternative in order to construction of microalloyed steels utilizing the deposition by magnetron sputtering technique as a microalloying element addiction in which Ti nanoparticles are dispersed in an iron matrix. The advantage of that technique in relation to the conventional metallurgical processes is the possibility of uniformly disperse the microalloying elements in the iron matrix. It was carried out deposition of Ti onto Fe powder in high CH4, H2, Ar plasma atmosphere, with two deposition times. After the deposition, the iron powder with nanoparticles of Ti dispersed distributed, were compacted and sintered at 1120 ° C in resistive furnace. Characterization techniques utilized in the samples of powder before and after deposition of Ti were Granulometry, Scanning Electron Microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX) and X-ray diffraction (DRX). In the case of sintered samples, it was carried out characterization by SEM and Vickers Microhardness assays. The results show which the deposition technique by magnetron sputtering is practicable in the dispersion of particles in iron matrix. The EDX microanalysis detected higher percentages of Ti when the deposition were carried out with the inert gas and when the deposition process was carried out with reactive gas. The presence of titanium in iron matrix was also evidenced by the results of X-ray diffraction peaks that showed shifts in the network matrix. Given these results it can be said that the technique of magnetron sputtering deposition is feasible in the dispersion of nanoparticles of iron matrix in Ti.
Resumo:
The mesoporous molecular sieves of the MCM-41 and FeMCM-41 type are considered promissory as support for metals used as catalysts in oil-based materials refine processes and as adsorbents for environmental protection proposes. In this work MCM-41 and FeMCM41 were synthesized using rice husk ash - RHA as alternative to the conventional silica source. Hydrothermal synthesis was the method chosen to prepare the materials. Pre-defined synthesis parameters were 100°C for 168 hours, later the precursor was calcinated at 550°C for 2 hours under nitrogen and air flow. The sieves containing different proportions of iron were produced by two routes: introduction of iron salt direct synthesis; and a modification post synthesis consisting in iron salt 1 % and 5% impregnation in the material followed by thermal decomposition. The molecular sieves were characterized by X ray diffraction XRD, Fourier transform infrared spectroscopy FT-IR, X ray fluorescence spectroscopy XFR, scanning electronic microscopy SEM, specific surface area using the BET method, Termogravimetry TG. The kinetic model of Flynn Wall was used with the aim of determining the apparent activation energy of the surfactant remove (CTMABr) in the MCM- 41 porous. The analysis made possible the morphology characterization, identifying the presence of hexagonal structure typical for mesoporous materials, as well as observation of the MCM41 and iron of characteristic bands.
Resumo:
The produced water is a byproduct formed due to production of petroleum and carries with it a high amount of contaminants such as oil particles in suspension, organic compounds and metals. Thus, these latter pollutants are very difficult to treat because of its high solubility in water. The objective of this work is to use and evaluate a microemulsioned system to remove metals ( K , Mg , Ba , Ca , Cr , Mn , Li , Fe ) of synthetic produced water. For the extraction of metals, it was used a pseudoternary diagram containing the following phases: synthetic produced water as the aqueous phase (AP), hexane as organic phase (OP), and a cosurfactant/surfactant ratio equal to four (C/S = 4) as the third phase, where the OCS (saponified coconut oil) was used as surfactant and n-butanol as cosurfactant. The synthetic produced water was prepared in a bench scale and the region of interest in the diagram for the removal of metals was determined by experimental design called. Ten points located in the phase Winsor II were selected in an area with a large amount of water and small amounts of reagents. The samples were analyzed in atomic absorption spectrometer, and the results were evaluated through a statistical assesment, allowing the efficiency analysis of the effects and their interactions. The results showed percentages of extraction above 90% for the metals manganese, iron, chromium, calcium, barium and magnesium, and around 45% for metals lithium and potassium. The optimal point for the simultaneous removal of metals was calculated using statistical artifact multiple response function (MR). This calculation showed that the point of greatest extraction of metals occurs was the J point, with the composition [72% AP, 9% OP, 19% C/S], obtaining a global extraction percentage about 80%. Considering the aspects analyzed, the microemulsioned system has shown itself to be an effective alternative in the extraction of metals on synthetic produced water remediation
Resumo:
O conhecimento sobre o crescimento e o acúmulo de nutrientes em hipobiotos de caramboleira permite melhor eficiência da adubação na produção de hipobiotos (porta-enxertos). Objetivou-se determinar o crescimento e o acúmulo de nutrientes em hipobiotos de caramboleira cultivada em solução nutritiva. O experimento constituiu de cinco tratamentos, referentes aos tempos de coleta 25; 50; 75; 100 e 125 dias após o transplantio, dispostos em delineamento inteiramente casualizado em seis repetições. As plantas utilizadas foram obtidas de sementes de frutos de caramboleira 'Malásia', cultivadas em vasos com solução nutritiva. Nos diferentes órgãos dos hipobiotos (folhas, caule e raízes), avaliou-se o crescimento e o acúmulo de nutrientes e os índices nutricionais, a cada 25 dias. O ponto de enxertia (6 mm) foi atingido aos 110 dias após o transplantio. A ordem decrescente dos nutrientes acumulados em cada hipobioto produzido é de (em mg por planta): N = 634; K = 368; Ca = 152; Mg = 106; S = 98; P = 88 (em µg por planta) de: Fe = 2.963; Mn = 2.165; B = 722; Zn =780, e Cu = 96. O acúmulo médio de nutrientes é maior nas folhas > caule = raízes. O período de maior exigência de nutrientes pelos hipobiotos é compreendido entre 25-75 dias após o transplantio. As diferentes taxas de acumulação líquida dos nutrientes, nas diferentes partes da caramboleira, nem sempre acompanham a taxa de acumulação de nutrientes do respectivo órgão.
Resumo:
For to establish the micronutrients sufficiency range for the cotton, was used the method of mathematical chance for nutritional monitory data of three cotton growth locations in the Midwest of the Brazil, evaluating 152 areas. The method of mathematical chance was adequate for to establish cotton micronutrients references values, can be to help parameters were the conventional research cannot to prove in the short time. The micronutrients sufficiency range for productivity of 4000kg ha(-1) were, in the mg kg(-1), 41-89; 4-14; 90-230; 23-100; 25-50, and for 4500kg ha(-1) was 53-83; 4-12; 110-440; 40-60 e 25-50 for B, Cu, Fe, Mn and Zn, respectively. The sufficiency ranges indicated was similar to the existing official recommendations, however, is indicated the approach for to supply the specifics of the systems. The limitations of the method can be minimized with the expansion of the nutritional monitoring system in the cotton crops.
Resumo:
Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)
Resumo:
O trabalho foi realizado com o objetivo de estimar a retenção e a exigência líquida dos minerais Na, K, Mg, S, Fe e Zn durante a gestação de cabras com um ou dois fetos. A estimativa de retenção foi baseada na diferença entre o total de cada mineral depositado no feto, útero, membranas, fluídos fetais e glândula mamária dos animais nas diferentes etapas da gestação e o total de cada mineral armazenado nas cabras vazias, utilizando-se o modelo de predição ln=A+Bx+Cx2, em que x=tempo de gestação. Os conteúdos de Na, K, Mg, S, Fe e Zn, durante as gestações de um e dois fetos foram de: 13,2 e 21,4 mg; 13,3 e 21,3 g; 2,1 e 3,7 mg; 5,5 e 9,3 mg; 575,5 e 981,0 mg; 112,6 e 164,7 mg nas gestações, resultando em exigências líquidas diárias de 0,13 e 0,11 g; 0,21 e 0,31 g; 0,06 e 0,11g; 0,17 e 0,21 g; 22,94 e 40,51 mg; 2,63 e 2,78 mg, respectivamente.
Resumo:
O objetivo do estudo foi avaliar a influência da presença de cinco íons em uma calda de pulverização contendo o surfatante Aterbane. A tensão superficial foi analisada por meio da medição da massa de um conjunto de 25 gotas, com quatro repetições constituindo um tratamento. O trabalho foi dividido em duas etapas. Na primeira, os tratamentos foram combinados em esquema fatorial 9x5x2, sendo nove concentrações do surfatante Aterbane (0,01; 0,025; 0,05; 0,1; 0,2; 0,5; 1; 2; e 3%), cinco íons (Mg++, Ca++, Fe+++, Cu+++ e Zn+++) e duas concentrações desses elementos (10 e 100 ppm). Na segunda etapa, os tratamentos foram combinados em esquema fatorial 5x5x1, utilizandose os mesmos cinco elementos (Mg++, Ca++, Fe+++, Cu+++ e Zn+++), em cinco concentrações (1, 5, 20, 50 e 200 ppm), com apenas uma concentração do surfatante Aterbane (0,025%). Outros nove tratamentos permitiram avaliar as tensões superficiais das concentrações do surfatante (0,01; 0,025; 0,05; 0,1; 0,2; 0,5; 1; 2; e 3%) sem a adição dos íons. Os resultados mostraram que houve interferência dos íons sobre as soluções, já que, com exceção do Fe+++ (na concentração de 10 e 100 ppm) e do Cu+++ (na concentração de 100 ppm), todos os íons reduziram a tensão mínima alcançada e aumentaram a eficiência do surfatante, implicando benefícios à ação do surfatante e sobre as características de possíveis soluções de aplicação. Todos os íons avaliados promoveram reduções nas tensões superficiais de soluções do surfatante na concentração de 0,025%.
Resumo:
An investigation is made of the influence from small amounts of the protein bovine serum albumin (BSA) on the lateral organization of low molecular weight surfactant sodium bis-2-ethylhexyl sulfosuccinate (AOT) at the air-water interface. Surface pressure (pi - A), surface potential (DeltaV - A) and Brewster angle microscopy (BAM) experiments were carried out, with particular emphasis on the monolayer stability under successive compression-expansion cycles. AOT monolayer is not stable at the air-water interface, which means that the majority of AOT molecules go into the aqueous subphase as monomers and/or normal micelles. When a waiting time elapses between spreading and compression, the surfactant monolayer tends to reorganize partially at the air-water interface, with a monolayer expansion being observed for waiting times as large as 12 h. The incorporation of very small amount of BSA (10(-9) M) at the interface, also inferred from BAM, increases the monolayer stability as revealed by pi - A and DeltaV - A results. For a waiting time of circa 3 h, the mixed monolayer reaches its maximum stability. This must be related to protein (and/or protein-surfactant complexes) adsorbed onto the AOT monolayer, thus altering the BSA conformation to accommodate its hydrophobic/hydrophilic residues. Furthermore, the effects from such small amounts of BSA in the monolayer formation and stabilization mean that the AOT monolayer responds cooperatively to BSA. (C) 2004 Elsevier B.V. All rights reserved.
Resumo:
Surface-enhanced resonance Raman scattering (SERRS) is used for single-molecule detection from spatially resolved 1-mum(2) sections of a Langmuir-Blodgett (LB) monolayer deposited onto a Ag film. The target molecule, his (benzimidazo) thioperylene (BZP), is dispersed in an arachidic acid monomolecular layer containing one BZP molecule per mum(2) which is also the probing area of the Raman microscope. For concentrated samples (attomole quantities in the field of view), average SERRS, surface-enhanced fluorescence (SEF), and Raman imaging, including line mapping and global images at different temperatures, were recorded. Single-molecule SERRS spectra, obtained using an LB monolayer, present changes in bandwidth and relative intensities, highlighting the properties of single-molecule SERRS that are lost in average SERRS measurements of mixed LB monolayers obtained at the same temperatures. Also, the dilute system phenomenon of blinking is discussed with regard to results obtained from LB monolayers. The dilution process used in the single-molecule LB SERRS work is independently supported by fluorescence results obtained from very dilute solutions with monomer concentrations down to 10(-12) M.