Obtenção e caracterização de dióxido de estanho nanoestruturado pelo método de síntese contínua por combustão em solução

Continuous Synthesis by Solution Combustion was employed in this work aiming to obtain tin dioxide nanostructured. Basically, a precursor solution is prepared and then be atomized and sprayed into the flame, where its combustion occurs, leading to the formation of particles. This is a recent technique that shows an enormous potential in oxides deposition, mainly by the low cost of equipment and precursors employed. The tin dioxide (SnO2) nanostructured has been widely used in various applications, especially as gas sensors and varistors. In the case of sensors based on semiconducting ceramics, where surface reactions are responsible for the detection of gases, the importance of surface area and particle size is even greater. The preference for a nanostructured material is based on its significant increase in surface area compared to conventional microcrystalline powders and small particle size, which may benefit certain properties such as high electrical conductivity, high thermal stability, mechanical and chemical. In this work, were employed as precursor solution tin chloride dehydrate diluted in anhydrous ethyl alcohol. Were utilized molar ratio chloride/solvent of 0,75 with the purpose of investigate its influence in the microstructure of produced powder. The solution precursor flux was 3 mL/min. Analysis with X-ray diffraction appointed that a solution precursor with molar ratio chloride/solvent of 0,75 leads to crystalline powder with single phase and all peaks are attributed to phase SnO2. Parameters as distance from the flame with atomizer distance from the capture system with the pilot, molar ratio and solution flux doesn t affect the presence of tin dioxide in the produced powder. In the characterization of the obtained powder techniques were used as thermogravimetric (TGA) and thermodiferential analysis (DTA), particle size by laser diffraction (GDL), crystallographic analysis by X-ray diffraction (XRD), morphology by scanning electron microscopy (SEM), transmission electron microscopy (TEM), specific surface area (BET) and electrical conductivity analysis. The techniques used revealed that the SnO2 exhibits behavior of a semiconductor material, and a potentially promising material for application as varistor and sensor systems for gas

Estudo comparativo de pás para aerogeradores de grande porte fabricadas em materiais compósitos reforçadas com fibra de carbono ou fibra de vidro

The research and development of wind turbine blades are essential to keep pace with worldwide growth in the renewable energy sector. Although currently blades are typically produced using glass fiber reinforced composite materials, the tendency for larger size blades, particularly for offshore applications, has increased the interest on carbon fiber reinforced composites because of the potential for increased stiffness and weight reduction. In this study a model of blade designed for large generators (5 MW) was studied on a small scale. A numerical simulation was performed to determine the aerodynamic loading using a Computational Fluid Dynamics (CFD) software. Two blades were then designed and manufactured using epoxy matrix composites: one reinforced with glass fibers and the other with carbon fibers. For the structural calculations, maximum stress failure criterion was adopted. The blades were manufactured by Vacuum Assisted Resin Transfer Molding (VARTM), typical for this type of component. A weight comparison of the two blades was performed and the weight of the carbon fiber blade was approximately 45% of the weight of the fiberglass reinforced blade. Static bending tests were carried out on the blades for various percentages of the design load and deflections measurements were compared with the values obtained from finite element simulations. A good agreement was observed between the measured and calculated deflections. In summary, the results of this study confirm that the low density combined with high mechanical properties of carbon fibers are particularly attractive for the production of large size wind turbine blades

Pirólise termoquímica de pós da fibra de coco seco em um reator de cilindro rotativo para produção de bio-óleo

This master thesis aims at developing a new methodology for thermochemical degradation of dry coconut fiber (dp = 0.25mm) using laboratory rotating cylinder reactor with the goal of producing bio-oil. The biomass was characterized by infrared spectroscopy with Fourier transform FTIR, thermogravimetric analysis TG, with evaluation of activation energy the in non-isothermal regime with heating rates of 5 and 10 °C/min, differential themogravimetric analysis DTG, sweeping electron microscopy SEM, higher heating value - HHV, immediate analysis such as evaluated all the amounts of its main constituents, i.e., lignin, cellulose and hemicelluloses. In the process, it was evaluated: reaction temperature (450, 500 and 550oC), carrier gas flow rate (50 and 100 cm³/min) and spin speed (20 and 25 Hz) to condensate the bio-oil. The feed rate of biomass (540 g/h), the rotation of the rotating cylinder (33.7 rpm) and reaction time (30 33 min) were constant. The phases obtained from the process of pyrolysis of dry coconut fiber were bio-oil, char and the gas phase non-condensed. A macroscopic mass balance was applied based on the weight of each phase to evaluate their yield. The highest yield of 20% was obtained from the following conditions: temperature of 500oC, inert gas flow of 100 cm³/min and spin speed of 20 Hz. In that condition, the yield in char was 24.3%, non-condensable gas phase was 37.6% and losses of approximately 22.6%. The following physicochemical properties: density, viscosity, pH, higher heating value, char content, FTIR and CHN analysis were evaluated. The sample obtained in the best operational condition was subjected to a qualitative chromatographic analysis aiming to know the constituents of the produced bio-oil, which were: phenol followed by sirigol, acetovanilona and vinyl guaiacol. The solid phase (char) was characterized through an immediate analysis (evaluation of moisture, volatiles, ashes and fixed carbon), higher heating value and FTIR. The non-condensing gas phase presented as main constituents CO2, CO and H2. The results were compared to the ones mentioned by the literature.

Nitrogênio, fósforo, potássio, adubo orgânico e calcário dolomítico na produção de sementes de grama-batatais (Paspalum notatum Flügge) em Latossol Vermelho Escuro

Comparou-se a produção de sementes de grama-batatais em Latossol vermelho Escuro com ou sem adição de sulfato de amônio (4g de N/m²), superfosfato simples (50g de P2O5/m²), cloreto de potássio (15g de K2O/m²), esterco de equino (10 litros/m²) e calcário dolomítico (220 g/m²). As produções foram avaliadas através de número de espigas por área, peso total de sementes, peso de sementes puras, relação entre peso de sementes puras e peso total de sementes, peso de 1000 sementes puras, peso total de sementes por espiga, peso de sementes puras por espiga, porcentagem de germinação das sementes e velocidade de emergência das plântulas. Foram determinados os teores de nitrogênio, fósforo, potássio, cálcio, magnésio, enxofre, boro, cobre, ferro, manganês e zinco na matéria seca de folhas e sementes. Verificou-se que a produção de sementes, tanto em quantidade como em qualidade, foi influenciada pela nutrição mineral. As porcentagens mais elevadas de carbono no solo estiveram associadas a maior quantidade e melhor qualidade das sementes produzidas. As melhores produções de sementes correspondem aos níveis mais baixos de fósforo, potássio, cálcio e zinco nas folhas. Verificou-se serem importantes nas características avaliadas as seguintes relações entre teores de nutrientes nas folhas ou nas sementes: N/P, P/Ca, P/Mg, P/S, P/Zn, K/Ca, K/Mg, K/B, Ca/Mg, Ca/B, Fe/Mn, Zn/Cu, Zn/Fe e Zn/Mn. Nas maiores produções, as sementes apresentaram concentrações menores de nitrogênio, boro e cobre, e mais elevadas de cálcio. As sementes de melhor qualidade apresentaram maiores concentrações de zinco e menores de boro. A aplicação de adubos ou calcário dolomítico não melhorou significativamente a produção de sementes.

Soil CO2 emission of sugarcane fields as affected by topography

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Análise espacial de atributos físicos e carbono orgânico em argissolo vermelho-amarelo cultivado com cana-de-açúcar

A agricultura convencional utiliza o solo intensivamente, modificando os seus atributos. Neste estudo, objetivou-se avaliar a variabilidade espacial de alguns atributos físicos e carbono orgânico do solo em um Argissolo Vermelho-Amarelo cultivado com cana-de-açúcar, usando geoestatística. O trabalho foi realizado em Maracanaú - CE, em uma área de produção de cana-de-açúcar, manejado mediante preparo conservacionista sobre uma cobertura de palhada de cana-de-açúcar. As amostras de solo foram retiradas de uma profundidade de 0,00 - 0,20 m, em uma malha, com intervalo regular de 10 m, totalizando 100 pontos. em cada amostra, foi analisado densidade de partículas, densidade do solo, carbono orgânico, porosidade total, macroposidade e microposidade. O coeficiente de variação indicou variabilidade baixa para densidade de partículas, densidade do solo e porosidade total e média para as variáveis macroporosidade, microporosidade e carbono orgânico. As variáveis analisadas mostraram dependência espacial, a qual foi observada nos mapas de krigagem. A distribuição de poros por tamanho e a porosidade total indicam condições físicas razoavelmente boas, embora com valores de densidade do solo ligeiramente acima do nível considerado adequado para a classe textural do solo.

Complexo enzimático para suínos: digestão, metabolismo, desempenho e impacto ambiental

Foram conduzidos dois experimentos para avaliar a suplementação enzimática (amilase, pentosanase, celulase, protease e a-galactosidase) em rações à base de milho e farelo de soja para suínos. No Exp 1, foram determinadas as digestibilidades aparentes da energia, matéria seca, proteína e das fibras das rações, com ou sem o complexo enzimático, para suínos machos castrados, com 19,96 ± 2,90 kg de peso vivo. Foi utilizado o método da coleta total de fezes e as rações foram formuladas com níveis reduzidos de energia, proteína e aminoácidos. No Exp 2, foram mensurados o desempenho, a excreção de sólidos totais e voláteis, matéria mineral, nitrogênio, macro e microminerais nas fezes, em relação ao desempenho, de suínos machos castrados dos 50 aos 151 dias de idade, com peso médio inicial de 18,34 ± 1,35 kg. Foram utilizadas três dietas, sendo uma ração formulada para atender ou exceder as exigências nutricionais dos animais, de acordo com o NRC (1998), e outras duas com níveis reduzidos de energia, proteína e aminoácidos, suplementadas ou não com o complexo enzimático. Foi utilizado o delineamento em blocos casualizados. A suplementação enzimática em rações contendo milho e farelo de soja não promoveu incrementos na digestibilidade de nutrientes, não melhorou o desempenho dos animais e também não reduziu a excreção de resíduos pelas fezes. Mais estudos são necessários para testar novas matrizes e diferentes níveis do complexo enzimático.

A pegada de carbono como um dos indicadores de sustentabilidade para medição da responsabilidade socioambiental empresarial: um estudo de caso na unidade sede da Petrobras em Natal-RN

As a contemporary tendency, it is been evidenced that the environmental changes theme, already admitted as a concernment to international economical and political reality, is also gaining repercussion on industrial and business sector. Firms are implementing actions on trial to minimize their own greenhouse gases (GHG) emissions impacts. However, the great majority of those actions of Corporative Social-Environmental Responsibility (CSR) are referred only to direct emissions of the main production systems. Direct emissions are those derived of an isolate process, without considering the upstream and downstream processes emissions, which respond for the majority of emissions originated because of respective firm‟s production system existence. Because the greenhouse effect occurs globally and the GHG emissions contribute to the environmental changes independently of their origin, it must be taken into account the whole productive life cycle of products and systems, since the energy invested on resources extraction and necessary materials to the final disposal. To do so, it must be investigated all relevant steps of a product/production system life cycle, tracking all activities which emit greenhouse gases, directly or indirectly. This amount of emissions consists in the firm‟s Carbon Footprint. This research purpose is to defend the Carbon Footprint relevance and its adoption viability to be used as an Environmental Indicator on measurement/assessment of CSR. It has been realized a study case on Petrobras‟s seat unity at Natal-Brazil, assessing part of its Carbon Footprint. It has been used the software GEMIS 4.6 to do the emissions quantifying. The items measured were the direct emissions of the own unity vehicles and indirect emissions of offset paper (A4), energy and disposable plastic cups consumed. To 2009, these emissions were 3.811,94 tCO2eq. We may conclude that Carbon Footprint quantification is indispensable to the knowledge of real emissions caused by a productive process existence, must serving as basis to CSR decisions about the environmental changes reversion challenge

Condutividade elétrica da solução nutritiva e produção de alface em hidroponia

A variação da condutividade elétrica da solução nutritiva altera a absorção de água e nutrientes pelas plantas, interferindo no metabolismo e, consequentemente, na produção das mesmas. Este trabalho, conduzido no período de agosto a outubro de 1999, avaliou o efeito da condutividade elétrica (CE) sobre a produção e desenvolvimento de alface americana de cabeça crespa, cultivar Ryder em hidroponia. As tendências de variação da condutividade elétrica do meio nutritivo, durante o desenvolvimento da alface, foram também avaliadas. Foi utilizado o delineamento inteiramente casualizado com seis repetições e três tratamentos, constituídos pelas condutividade elétricas: CE1= 1,46, CE2= 2,46 e CE3= 4,21 (± 0,24) mS cm-1. O diâmetro e altura da cabeça e peso seco da raiz não foram influenciados pelas condutividades elétricas da solução nutritiva. Os maiores pesos do material fresco e seco foram conseguidos com CE 2,46 (± 0,24) mS cm-1. Todos os tratamentos apresentaram a tendência de diminuição da condutividade elétrica, durante o cultivo da alface verificando-se que a condutividade elétrica teve influência sobre as características de produção da alface americana.

Degradação foto-fenton de carbono orgânico total em efluentes da indústria de beneficiamento de castanha de caju

At the cashew nut processing industry it is often the generation of wastewaters containing high content of toxic organic compounds. The presence of these compounds is due mainly to the so called liquid of the cashew nut (CNSL). CNSL, as it is commercially known in Brazil, is the liquid of the cashew nut. It looks like an oil with dark brown color, viscous and presents a high toxicity index due to the chemical composition, i.e. phenol compounds, such as anacardic acid, cardol, 2-methyl cardol and monophenol (cardanol). These compounds are bio resistant to the conventional treatments. Furthermore, the corresponding wastewaters present high content of TOC (total organic carbon). Therefore due to the high degree of toxicity it is very important to study and develop treatments of these wastewaters before discharge to the environmental. This research aims to decompose these compounds using advanced oxidative processes (AOP) based on the photo-Fenton system. The advantage of this system is the fast and non-selective oxidation promoted by the hydroxyl radicals (●OH), that is under determined conditions can totally convert the organic pollutants to CO2 and H2O. In order to evaluate the decomposition of the organic charge system samples of the real wastewater od a processing cashew nut industry were taken. This industry was located at the country of the state of Rio Grande do Norte. The experiments were carried out with a photochemical annular reactor equipped with UV (ultra violet) lamp. Based on preliminary experiments, a Doehlert experimental design was defined to optimize the concentrations of H2O2 and Fe(II) with a total of 13 runs. The experimental conditions were set to pH equal to 3 and temperature of 30°C. The power of the lamps applied was 80W, 125W and 250W. To evaluate the decomposition rate measures of the TOC were accomplished during 4 hours of experiment. According to the results, the organic removal obtained in terms of TOC was 80% minimum and 95% maximum. Furthermore, it was gotten a minimum time of 49 minutes for the removal of 30% of the initial TOC. Based on the obtained experimental results, the photo-Fenton system presents a very satisfactory performance as a complementary treatment of the wastewater studied

Levantamento e avaliação de critérios para a ampliação de escala da produção de biossurfactantes utilizando melaço como substrato

Biosurfactants are amphiphilic molecules synthesized by microorganisms such as bacteria, yeast or filamented fungi cultivated in various carbon sources among sucrose and hydrocarbons. These molecules are composed by a hydrophilic and hydrophobic part. They operate mostly at interfaces of fluids of different polarities. Because of this characteristic, they are potentially employed in numerous industries, such as the textile, medical, cosmetics, food and mainly in the petrochemical ones. Therefore industry has interest in developing new biosurfactant production processes in high scale, in order to become them economically competitive when compared to synthetic biosurfactants. This work aims to evaluate the biosurfactant production applying a non-conventional substrate sugar cane molasses proceeding from the sugar industry thus reducing the production costs. The strain identified as AP029/GLIIA, isolated from oil wells in Rio Grande do Norte state and used in these experiments belongs to the culture collection of Antibiotics Department of UFPE. The fermentation were carried out using different conditions according to a factorial planning 24 with duplicate at center point, in which the studied factors were molasse concentration, nitrate concentration, agitation and aeration ratio. The experiments were performed in a shaker at 38ºC of temperature. Samples were withdrawn in regular periods of time of up to 72 hours of fermentation in order to analyze substrate consumption, cellular concentration, superficial tension, critical micelle dilution (CMD-1 e CMD-2) as well as extracelullar protein production. The results showed a production of 3,480 g/L of biomass, a reduction of 41% on superficial tension, 67% of substrate consumption and 0,2805 g/L of extracellular protein

Estudo do mecanismo de produção de oligossacarídeos com atividades nutracêuticas a partir da quitosana por hidrólise enzimática com processo fermentativo simultâneo

The obtaining of the oligosaccharides from chitosanase, has showed interest of the pharmaceutical area in the last years due their countless functional properties. Although, the great challenge founded out is how to keep a constant and efficient production. The alternative proposed by this present work was to study the viability to develop an integrated technology, with reduced costs. The strategy used was the obtaining of the oligomers through enzymatic hydrolysis using chitosanolitic enzymes obtained straight from the fermented broth, eliminating this way the phases involved in the enzymes purification. The two chitosanases producing strains chosen for the work, Paenibacillus chitinolyticus and Paenibacillus ehimensis, were evaluated according to the behavior in the culture medium with simple sugar and in relation to the pH medium variations. The culture medium for the chitosanases induction and production was developed through addition of soluble chitosan as carbon source. The soluble chitosan was obtained using hydrochloric acid solution 0.1 M and afterwards neutralization with NaOH 10 M. The enzymatic complexes were obtained from induction process in culture medium with 0.2% of soluble chitosan. The enzymes production was verified soon after the consumption of the simple sugars by the microorganisms and the maximum chitosanolitic activity obtained in the fermented broth by Paenibacillus chitinolyticus was 249 U.L-1 and by Paenibacillus ehimensis was 495U.L-1. These two enzymatic complexes showed stability when stored at 20°C for about 91 days. The enzymes in the fermented broth by Paenibacillus chitinolyticus, when exposed at temperature of 55°C and pH 6.0, where the activity is maximum, showed 50% lost of activity after 3 hours Meanwhile, for the complex produced by Paenibacillus ehimensis, after 6 days of exposure, it was detected 100% of the activity. The chito-oligosaccharides obtained by the hydrolysis of a 1% chitosan solution, using the enzymatic complex produced by Paenibacillus chitinolyticus showed larger quantity after 9 hours hydrolysis and using the complex produced by Paenibacillus ehimensis after 20 minutes was observed the chito-ligosacharides with polymerization degree between 3 and 6 units. Evaluating these results, it was verified that the production of chitosan-oligosaccharides is possible, using a simultaneous process

Produção de bioetanol a partir de pedúnculo de caju (Anacardium occidentale L.) por fermentação submersa

Recently, global demand for ethanol fuel has expanded very rapidly, and this should further increase in the near future, almost all ethanol fuel is produced by fermentation of sucrose or glucose in Brazil and produced by corn in the USA, but these raw materials will not be enough to satisfy international demand. The aim of this work was studied the ethanol production from cashew apple juice. A commercial strain of Saccharomyces cerevisiae was used for the production of ethanol by fermentation of cashew apple juice. Growth kinetics and ethanol productivity were calculated for batch fermentation with different initial sugar (glucose + fructose) concentration (from 24.4 to 103.1 g.L-1). Maximal ethanol, cell and glycerol concentrations (44.4 g.L-1, 17.17 g.L-1, 6.4 g.L-1, respectively) were obtained when 103.1 g.L-1 of initial sugar concentration were used, respectively. Ethanol yield (YP/S) was calculated as 0.49 g (g glucose + fructose)-1. Pretreatment of cashew apple bagasse (CAB) with dilute sulfuric acid was investigated and evaluated some factors such as sulfuric acid concentration, solid concentration and time of pretreatment at 121°C. The maximum glucose yield (162.9 mg/gCAB) was obtained by the hydrolysis with H2SO4 0.6 mol.L-1 at 121°C for 15 min. Hydrolysate, containing 16 ± 2.0 g.L-1 of glucose, was used as fermentation medium for ethanol production by S. cerevisiae and obtained a ethanol concentration of 10.0 g.L-1 after 4 with a yield and productivity of 0.48 g (g glucose)-1 and 1.43 g.L-1.h-1, respectively. The enzymatic hydrolysis of cashew apple bagasse treated with diluted acid (CAB-H) and alkali (CAB-OH) was studied and to evaluate its fermentation to ethanol using S. cerevisiae. Glucose conversion of 82 ± 2 mg per g CAB-H and 730 ± 20 mg per g CAB-OH was obtained when was used 2% (w/v) of solid and loading enzymatic of 30 FPU/g bagasse at 45 °C. Ethanol concentration and productivity was achieved of 20.0 ± 0.2 g.L-1 and 3.33 g.L-1.h-1, respectively when using CAB-OH hydrolyzate (initial glucose concentration of 52.4 g.L-1). For CAB-H hydrolyzate (initial glucose concentration of 17.4 g.L-1), ethanol concentration and productivity was 8.2 ± 0.1 g.L-1 and 2.7 g.L-1.h-1, respectively. Hydrolyzates fermentation resulted in an ethanol yield of 0.38 g/g glucose and 0.47 g/g glucose, with pretreated CABOH and CAB-H, respectively. The potential of cashew apple bagasse as a source of sugars for ethanol production by Kluyveromyces marxianus CE025 was evaluated too in this work. First, the yeast CE025 was preliminary cultivated in a synthetic medium containing glucose and xylose. Results showed that it was able to produce ethanol and xylitol at pH 4.5. Next, cashew apple bagasse hydrolysate (CABH) was prepared by a diluted sulfuric acid pre-treatment. The fermentation of CABH was conducted at pH 4.5 in a batch-reactor, and only ethanol was produced by K. marxianus CE025. The influence of the temperature in the kinetic parameters was evaluated and best results of ethanol production (12.36 ± 0.06 g.L-1) was achieved at 30 ºC, which is also the optimum temperature for the formation of biomass and the ethanol with a volumetric production rate of 0.25 ± 0.01 g.L-1.h-1 and an ethanol yield of 0.42 ± 0.01 g/g glucose. The results of this study point out the potential of the cashew apple bagasse hydrolysate as a new source of sugars to produce ethanol by S. cerevisiae and K. marxianus CE025. With these results, conclude that the use of cashew apple juice and cashew apple bagasse as substrate for ethanol production will bring economic benefits to the process, because it is a low cost substrate and also solve a disposal problem, adding value to the chain and cashew nut production

Comportamento da produção de espécies reativas de oxigênio em miocárdio de ratos submetidos a treinamento de baixa intensidade em diferentes temperaturas

INTRODUÇÃO: A prática de exercício físico proporciona aumento da produção de espécies reativas de oxigênio (ERO) resultantes do metabolismo aeróbio e, gera uma quantidade significativa de calor, em conseqüência da produção de energia, resultando em sobrecarga orgânica. A associação entre ERO e exercício, e entre exercício e variações da temperatura ambiente têm sido estudadas, contudo, há escassez de informações que considere a associação entre produção de radicais livres no miocárdio e atividade física em temperatura elevada. OBJETIVO: Comparar a produção de ERO em miocárdio de ratos submetidos ao treinamento de baixa intensidade em diferentes temperaturas. MÉTODOS: Foram utilizados 20 ratos Wistar, machos, jovens, peso (250 a 280g), divididos em quatro grupos: G1 (n = 5) expostos ao treinamento e calor (39º ± 1C); G2 (n = 5) expostos somente ao calor durante o mesmo período de G1, sem treinamento; G3 (n = 5) expostos ao treinamento em temperatura ambiente (22º ± 1C); G4 (n = 5) expostos à temperatura ambiente sem treinamento. O treinamento foi realizado em esteira rolante climatizada por cinco semanas, evoluindo 5 minutos a cada duas sessões finalizando em 60 minutos em baixa intensidade 8m/min. O ambiente foi controlado entre 39 ± 1ºC e 22 ± 1ºC e entre 40 e 60 % de umidade relativa. A lipoperoxidação foi avaliada por Quimiluminescência (QL). A análise dos dados foi realizada a partir do teste Two Way ANOVA para análise da QL e t de student para a Capacidade Antioxidante Total (TRAP). RESULTADOS: A análise da QL revelou uma curva de emissão de luz significantemente mais baixa para o grupo exposto ao exercício em normotermia comparado aos sedentários mantidos no calor. A análise da TRAP mostrou diminuição em todos os grupos experimentais em relação ao G4. CONCLUSÃO: Concluiu-se que houve níveis menores de produção de ERO nos grupos submetidos somente ao calor ou somente ao exercício.

Metabolismo mitocondrial, radicais livres e envelhecimento

O envelhecimento pode estar associado ao maior acúmulo de lesões celulares decorrentes das espécies reativas do oxigênio e do nitrogênio derivadas do metabolismo mitocondrial. Com a progressão da idade, há acúmulo de proteínas, lipídeos, carboidratos e DNA oxidados em relação a organismos jovens, de acordo com a teoria dos radicais livres. Entretanto, nem sempre os idosos ou animais envelhecidos apresentam maior estresse oxidativo que os jovens. Este artigo discute o paradoxo da teoria dos radicais livres de acordo com a teoria da biogênese da manutenção adequada do metabolismo mitocondrial. Diversos fatores podem contribuir para a redução do estresse oxidativo, como a hormese induzida pela prática regular de exercícios físicos, a restrição calórica, a ingestão de antioxidantes nutricionais e o aumento da produção de antioxidantes celulares que. em conjunto, estes promovem a expressão das sirtuínas e das proteínas do choque térmico, protegendo a integridade e funcionalidade mitocondriais, reduzindo o estresse oxidativo e nitrosativo, o que está associado à redução do envelhecimento e aumento da longevidade.