Drying soybean seed using air ambient temperature at low relative humidity

Under subtropical and tropical environments soybean seed (Glycine max (L.) Merrill) are harvested early to avoid deterioration from weathering. Careful after-harvest drying is required and is an important step in maintaining the physiological quality of the seed. Soybean seed should be harvested when the moisture content is in a range of 16-20%. Traditional drying utilizes a high temperature air stream passed through the seed mass without dehumidification. The drying time is long because the system is inefficient and the high temperature increases the risk of thermal damage to the seed. New technology identified as heat pipe technology (HPT) is available and has the unique feature of removing the moisture from the air stream before it is passed through the seed mass at the same environmental temperature. Two studies were conducted to evaluate the performance of HPT for dry soybean seed. In the first study the seeds were dried from 17.5 to 11.1% in 2 hours and 29 minutes and in the second sudy the seeds were dried from 22.6 to 11.9% in 16 hours and 32 minutes. This drying process caused no reduction in seed quality as measured by the standard germination, tetrazolium-viability, accelerated aging and seedling vigor classification tests. The only parameter that indicated a slight seed quality reduction was tetrazolium vigor in the second study. It was concluded that the HPT system is a promising technology for drying soybean seed when efficiency and maintenance of physiological quality are desired.

Drying peanut seed using air ambient temperature at low relative humidity

The moisture content of peanut kernel (Arachis hypogaea L.) at digging ranges from 30 to 50% on a wet basis (w.b.). The seed moisture content must be reduced to 10.5% or below before seeds can be graded and marketed. After digging, peanuts are cured on a window sill for two to five days then mechanically separated from the vine. Heated air is used to further dry the peanuts from approximately 18 to 10% moisture content w.b. Drying is required to maintain peanut seed and grain quality. Traditional dryers pass a high temperature and high humidity air stream through the seed mass. The drying time is long because the system is inefficient and the high temperature increases the risk of thermal damage to the kernels. New technology identified as heat pipe technology (HPT) is available and has the unique feature of removing the moisture from the air stream before it is heated and passed through the seed. A study was conducted to evaluate the performance of the HPT system in drying peanut seed. The seeds inside the shells were dried from 17.4 to 7.3% in 14 hours and 11 minutes, with a rate of moisture removal of 0.71% mc per hour. This drying process caused no reduction in seed quality as measured by the standard germination, accelerated ageing and field emergence tests. It was concluded that the HPT system is a promising technology for drying peanut seed when efficiency and maintenance of physiological quality are desired.

Synthesis and characterization of nanoperforated metal oxide thin films

For advanced devices in the application fields of data storage, solar cell and biosensing, one of the major challenges to achieve high efficiency is the fabrication of nanopatterned metal oxide surfaces. Such surfaces often require both precise structure at the nanometer scale and controllable patterned structure at the macro scale. Nowadays, the dominating candidates to fabricate nanopatterned surfaces are the lithographic technique and block-copolymer masks, most of which are unfortunately costly and inefficient. An alternative bottom-up approach, which involves organic/inorganic self-assembly and dip-coating deposition, has been studied intensively in recent years and has proven to be an effective technique for the fabrication of nanoperforated metal oxide thin films. The overall objective of this work was to optimize the synthesis conditions of nanoperforated TiO2 (NP-TiO2) thin films, especially to be compatible with mixed metal oxide systems. Another goal was to develop fabrication and processing of NP-TiO2 thin films towards largescale production and seek new applications for solar cells and biosensing. Besides the traditional dip-coating and drop-casting methods, inkjet printing was used to prepare thin films of metal oxides, with the advantage of depositing the ink onto target areas, further enabling cost-effective fabrication of micro-patterned nanoperforated metal oxide thin films. The films were characterized by water contact angle determination, Atomic Force Microscopy, Scanning Electron Microscopy, X-ray Photoelectron Spectroscopy and Grazing Incidence XRay Diffraction. In this study, well-ordered zinc titanate nanoperforated thin films with different Zn/Ti ratios were produced successfully with zinc precursor content up to 50 mol%, and the dominating phase was Zn2Ti3O8. NP-TiO2 structures were also obtained by a cost-efficient means, namely inkjet printing, at both ambient temperature and 60 °C. To further explore new biosensing applications of nanoperforated oxide thin films, inkjet printing was used for the fabrication of both continuous and patterned polymeric films onto NP-TiO2 and perfluorinated phosphate functionalized NP-TiO2 substrates, respectively. The NP-TiO2 films can be also functionalized with a fluoroalkylsilane, resulting in hydrophobic surfaces on both titania and silica. The surface energy contrast in the nanoperforations can be tuned by irradiating the films with UV light, which provides ideal model systems for wettability studies.

Hydrogen Sensor Application of Anodic Titanium Oxide Nanostructures

Hydrogen (H2) fuel cells have been considered a promising renewable energy source. The recent growth of H2 economy has required highly sensitive, micro-sized and cost-effective H2 sensor for monitoring concentrations and alerting to leakages due to the flammability and explosiveness of H2 Titanium dioxide (TiO2) made by electrochemical anodic oxidation has shown great potential as a H2 sensing material. The aim of this thesis is to develop highly sensitive H2 sensor using anodized TiO2. The sensor enables mass production and integration with microelectronics by preparing the oxide layer on suitable substrate. Morphology, elemental composition, crystal phase, electrical properties and H2 sensing properties of TiO2 nanostructures prepared on Ti foil, Si and SiO2/Si substrates were characterized. Initially, vertically oriented TiO2 nanotubes as the sensing material were obtained by anodizing Ti foil. The morphological properties of tubes could be tailored by varying the applied voltages of the anodization. The transparent oxide layer creates an interference color phenomena with white light illumination on the oxide surface. This coloration effect can be used to predict the morphological properties of the TiO2 nanostructures. The crystal phase transition from amorphous to anatase or rutile, or the mixture of anatase and rutile was observed with varying heat treatment temperatures. However, the H2 sensing properties of TiO2 nanotubes at room temperature were insufficient. H2 sensors using TiO2 nanostructures formed on Si and SiO2/Si substrates were demonstrated. In both cases, a Ti layer deposited on the substrates by a DC magnetron sputtering method was successfully anodized. A mesoporous TiO2 layer obtained on Si by anodization in an aqueous electrolyte at 5°C showed diode behavior, which was influenced by the work function difference of Pt metal electrodes and the oxide layer. The sensor enabled the detection of H2 (20-1000 ppm) at low operating temperatures (50–140°C) in ambient air. A Pd decorated tubular TiO2 layer was prepared on metal electrodes patterned SiO2/Si wafer by anodization in an organic electrolyte at 5°C. The sensor showed significantly enhanced H2 sensing properties, and detected hydrogen in the range of a few ppm with fast response/recovery time. The metal electrodes placed under the oxide layer also enhanced the mechanical tolerance of the sensor. The concept of TiO2 nanostructures on alternative substrates could be a prospect for microelectronic applications and mass production of gas sensors. The gas sensor properties can be further improved by modifying material morphologies and decorating it with catalytic materials.

Optimal distance of the light-curing tip for light transmission through the resin composite

Hammaslääketieteessä käytetettävien komposiittien valonläpäisevyys vaihtelee. Samoin LED-valokovettimet eroavat toisistaan valotehonsa ja muotoilunsa perusteella. On yleisesti tiedossa, että valokovettimesta tulevan valon intensiteetti pinta-alayksikköä kohden heikkenee, kun kovettimen etäisyys kasvaa. Toisaalta ei ole tiedossa, miten valokovetettavan kohteen ja valokovettimen kärjen väliin sijoitettu materiaali tarkalleenottaen vaikuttaa valon intensiteettiin eri etäisyyksiä käytettäessä. Tämän tutkimuksen tarkoituksena on selvittää, miten valokovetettavan kohteen ja valokovettimen kärjen väliin asetettava etukäteen polymerisoitu materiaali vaikuttaa valon intensiteettiin eri etäisyyksillä. Tutkimus suoritettiin käyttämällä kahta eri valokovetinta. Jotta etäisyyden vaikutusta valotustehoon voitiin demonstroida, vaihdettiin kovettimen etäisyyttä sensorista 0,2,4,6,8,10mm välillä. Valotehot rekisteröitiin MARC resin calibrator -laitteella. Sensorin ja valokovettimen kärjen väliin asetettavat erilaiset komposiittilevyt olivat valmiiksi kovetettuja,1mm paksuisia, filleripitoisuuksiltaan neljää erilaista muovia. Valotehot rekisteröitiin jokaiselta etäisyydeltä komposiitin ollessa sensorin päällä. Rinnakkaisesti verrattiin myös etäisyyden vaikutusta valotehoon ilman esikovetettua materiaalia kovettimen kärjen ja valoa mittaavan sensorin välissä. Vertailun suorittamiseksi laskettiin intensiteettisuhdeluku muovillisen ja muovittoman arvon välillä aina tietyllä etäisyydellä Valokovettimen kärjen etäisyyden kasvattaminen sensorista (eli valokovetettavasta kohteesta) odotusten mukaisesti pienensi valotehoa. Laittamalla sensorin ja kovettimen väliin komposiittilevy, valoteho pieneni odotetusti vielä enemmän. Tutkittaessa intensiteettisuhdetta (valoteho muovin kanssa : valoteho ilman muovia) kuitenkin huomattiin, että 4-6mm:n kohdalla suhdeluku oli suurempi kuin 0,2,8 ja 10mm kohdalla. Johtopäätöksenä oli, että suurin mahdollinen valokovetusteho saavutetan laittamalla kovetuskärki mahdollisimman lähelle kohdetta. Jos valokovetettavan kohteen ja valokovettimen kärjen välissä oli kiinteä komposiittipalanen, suurin mahdollinen valokovetusteho kohteeseen saavutetaan edelleen laittamalla kovetuskärki kiinni muoviin. Jos etäisyyttä muovin pinnasta sen sijaan kasvatettiin, valokovetusteho ei laskenutkaan niin nopeasti kuin oli odotettu. Tämä voi liittyä siihen, että tehokkaan valokeilan halkaisijan koko on suurempi verrattuna komposiitin sekä sensorin halkaisian kokoon. Toiseksi on arvioitu, että resiinikomposiitin täyteaineet voisivat fokusoida läpi kulkevaa valoa sensoriin. Se, pitääkö tämä ilmiö paikkansa, vaatii kuitenkin enemmän tutkimusta

Freedom of choice and bounded rationality: a brief appraisal of behavioral economists' plea for light paternalism

Behavioral economics has addressed interesting positive and normative questions underlying the standard rational choice theory. More recently, it suggests that, in a real world of boundedly rational agents, economists could help people to improve the quality of their choices without any harm to autonomy and freedom of choice. This paper aims to scrutinize available arguments for and against current proposals of light paternalistic interventions mainly in the domain of intertemporal choice. It argues that incorporating the notion of bounded rationality in economic analysis and empirical findings of cognitive biases and self-control problems cannot make an indisputable case for paternalism.

Price movement in the Brazilian land market (1994-2010): an analysis in the light of post-Keynesian theory

ABSTRACT The present study aims to evaluate crop, pasture and forest land prices in Brazil, between 1994 and 2010, in the light of Post-Keynesian theory. The results provide evidence that land, more than just a simple factor of production, must be conceived of as an economic asset. In fact, the price of rural land is determined not only by the expected profitability deriving from agricultural activities but also by the agents' expectations about its future appreciation and liquidity in an economic environment permeated with uncertainty. In this context, as an object of speculation, land has been particularly important as a store of value.

Geographical Studies of Underwater Light Dynamics in the Coastal Archipelago of SW Finland, Baltic Sea

The underwater light field is an important environmental variable as it, among other things, enables aquatic primary production. Although the portion of solar radiation that is referred to as visible light penetrates water, it is restricted to a limited surface water layer because of efficient absorption and scattering processes. Based on the varying content of optical constituents in the water, the efficiency of light attenuation changes in many dimensions and over various spatial and temporal scales. This thesis discusses the underwater light dynamics of a transitional coastal archipelago in south-western Finland, in the Baltic Sea. While the area has long been known to have a highly variable underwater light field, quantified knowledge on the phenomenon has been scarce, patchy, or non-existent. This thesis focuses on the variability in the underwater light field through euphotic depths (1% irradiance remaining), which were derived from in situ measurements of vertical profiles of photosynthetically active radiation (PAR). Spot samples were conducted in the archipelago of south-western Finland, mainly during the ice-free growing seasons of 2010 and 2011. In addition to quantifying both the seasonal and geographical patterns of euphotic depth development, the need and usability of underwater light information are also discussed. Light availability was found to fluctuate in multiple dimensions and scales. The euphotic depth was shown to have combined spatio-temporal dynamics rather than separate changes in spatial and temporal dimensions. Such complexity in the underwater light field creates challenges in data collection, as well as in its utilisation. Although local information is needed, in highly variable conditions spot sampled information may only poorly represent its surroundings. Moreover, either temporally or spatially limited sampling may cause biases in understanding underwater light dynamics. Consequently, the application of light availability data, for example in ecological modelling, should be made with great caution.

Synechococcus sp. PCC 7002 CpcB lyase null mutations alter phycocyanin chromophore function and, consequently, affect the redistribution of excitation energy via the light state transition /

Phycobilisomes are the major light harvesting complexes for cyanobacteria and phycocyanin is the primary phycobiliprotein of the phycobilisome rod. The phycocyanobilin lyases responsible for chromophorylating the phycocyanin p subunit (CpcB) have been recently identified in the cyanobacterium Synechococcus sp. PCC 7002. Surprisingly, mutants missing the CpcB lyases were nevertheless capable of producing pigmented phycocyanin. 10K absorbance measurements revealed that the energy states of the p phycocyanin chromophores were only subtly shifted; however, 77K steady state fluorescence emission spectroscopy showed excitation energy transfer involving the targeted chromophores to be highly disrupted. Such evidence suggests that phycobilin orientation within the binding domain is specifically modified. We hypothesized that alternate, less specific lyases are able to act on the p binding sites. A phycocyanin linker-polypeptide deficient mutant was similarly characterized. The light state transition, a short term adaptation of the photosynthetic light harvesting apparatus resulting in the redistribution of excitation energy among the photo systems, was shown to be dominated by the reallocation of phycocyanin-absorbed excitation energy. Treatment with a high M phosphate buffer effectively prevented the redistribution of both chlorophyll a- and phycobilisome- absorbed excitation energy, suggesting that the two effects are not strictly independent. The mutant strains required a larger redistribution of excitation energy between light states, perhaps to compensate for their loss in phycobilisome antenna function.

Characterization of the phosphorylation of thylakoid membrane proteins from cyanobacterium synechococcus sp. PCC 6301 in light state 1 and light state 2

The distribution of excitation energy between the two photosystems (PSII and PSI) of photosynthesis is regulated by the light state transition. Three models have been proposed for the mechanism of the state transition in phycobilisome (PBS) containing organisms, two involving protein phosphorylation. A procedure for the rapid isolation of thylakoid membranes and PBS fractions from the cyanobacterium Synechococcus m. PCC 6301 in light state 1 and light state 2 was developed. The phosphorylation of thylakoid and soluble proteins rapidly isolated from intact cells in state 1 and state 2 was investigated. 77 K fluorescence emission spectra revealed that rapidly isolated thylakoid membranes retained the excitation energy distribution characteristic of intact cells in state 1 and state 2. Phosphoproteins were identified by gel electrophoresis of both thylakoid membrane and phycobilisome fractions isolated from cells labelled with 32p orthophosphate. The results showed very close phosphoprotein patterns for either thylakoid membrane or PBS fractions in state 1 and state 2. These results do not support proposed models for the state transition which required phosphorylation of PBS or thylakoid membrane proteins.

Environmental assessment and biomonitoring of the Twelve Mile Creek watershed, Niagara Peninsula, Ontario

In light of the heavy reliance of the people of the Niagara Peninsula on the T\\'elve Mile Creek (TMC) watershed for recreational activities and for municipal and industrial uses ( e.g., drinking water, shipping and discharge of effluents), it was deemed prudent to assess the envirol1tnental health of the system by analysing the sediments total and exchangeable metal, and TPH contents. The MOEE has set guidelines with limits for the protection and management of aquatic sediments, and the sediments from the headwaters of the TMC have total metal and TPH (subset of O&G) contents well below the lower provincial limits. Areas of environmental concern where total metal contents in sediments, either individually or collectively, exceed the guideline, are the south side of Lake Gibson, the Old WeIland Canal, a segment of TMC just south of the QEW and Martindale Pond. The total metal content of sediments does not in all instances identify areas of biological concern. Instead, it has been found that the exchangeable metal fraction of sediments is a better indicator of metal availability and thus potential accumulation in organisms. In some instances, the exchangeable metal fraction agrees with the total metal fraction defining areas of environmental concern, but it does vary from site to site reflecting the natural variability of the ambient environment. Overall, the exchangeable metal fraction of sediments appears to be a better indicator of anthropogenic pollution and ecosystem impact. A histochemical study of Anodon.ta sp., Elliptio sp. and zebra mussels (Dreissena polyn'101pha) was done in conjunction with passive biomonitoring of zebra and quagga mussels (Dreissena bugensis) from the Twelve Mile Creek watershed and Lake 51. Clair (Jeanette's Creek, Chatham, Ontario). The highest concentrations of divalent metals such as Cu, Ni, Cd, and Zn, and trivalent Al appear to accumulate in gill and kidney tissues. Metal contents of organ tissues in Anodonta sp. vary with size class. Organ metal content varies among size classes, thus requiring consideration of size in biomonitoring studies. Shucked zebra and quagga mussel tissues, exhibited similar size class to Al content trends. In addition they reflected the Al content trends of top (approximately 10 cm) most sediments in the Twelve Mile Creek watershed. Quagga mussels appear to have higher Al concentrations than zebra mussels, thus suggesting that quagga mussels may be better passive biomonitors of AI. Cd content in zebra mussel tissues, seemed to increase with size class trends. This was not demonstrated in the quagga mussel tissues. This suggests that Cd may be regulated by quagga mussels and not by zebra mussels, and that zebra mussels may be better passivebiomonitors of Cd than are quagga mussels. Zebra mussel, quagga mussel, Anodonta sp., and Elliptio sp. were used in a two part, active (translocated) biomonitoring study of the Twelve Mile Creek watershed. There was no statistical difference in death rates between zebra and quagga mussels after 65 days of biomonitoring. However there does appear to be a difference of death rates between sites. Unfortunately the data base did not permit us to differentiate between sites. Relative to Port Colborne Harbour (Port Colborne, Ontario), the Twelve Mile Creek watershed appears to be elevated in bioavailable AI. An area near the terminus of the Twelve Mile Creek appears to be an area of environmental concern since mussels seemed to have accumulated relatively large concentrations of Cd, Zn, and Pb. In addition to possible metal loading from a nearby outfalls, or possible upstream outfalls, road salt runoff from storm sewers may have contributed to metal accumulation through cation exchanges processes. Similar trends in cumulative quagga mussel metal concentrations during the two time periods (65 and 159 days), suggest that quagga mussels may reach equilibrium within 65 days of translocation. Differences in bioaccumulated metal concentrations of the two dreissenid species demonstrate that active biomonitoring studies must use a variety of organisms to adequately assess the environmental situation of specific waterways and/or bodies.

Factors influencing the seasonal changes in primary productivity of the photosynthetic bacteria of Crawford Lake, Ontario

A naturally occurring population of photosynthetic bacteria, located in the meromictic Crawford Lake, was examined during two field seasons (1979-1981). Primary production, biomass, light intensity, lake transparency, pH and bicarbonate concentration were all monitored during this period at selected time intervals. Analysis of the data indicated that (l4C) bacterial photosynthesis was potentially limited by the ambient bicarbonate concentration. Once a threshold value (of 270 mg/l) was reached a dramatic (2 to 10 fold) increase in the primary productivity of the bacteria was observed. Light intensity appeared to have very little effect on the primary productivity of the bacteria, even at times when analyses by Parkin and Brock (1980a) suggested that light intensity could be limiting (i.e., 3.0-5.0 ft. candles). Shifts in the absorption maxima at 430 nrn of the .bacteriochlorophyll spectrum suggested that changes in the species or strain composition of the photosynthetic bacteria had occurred during the summer months. It was speculated that these changes might reflect seasonal variation in the wavelength of light reaching the bacteria. Chemocline erosion did not have the same effect on the population size (biomass) of the photosynthetic bacteria in Crawford Lake (this thesis) as it did in Pink Lake (Dickman, 1979). In Crawford Lake the depth of the chemocline was lowered with no apparent loss in biomass (according to bacteriochlorophyll data). A reverse current was. proposed to explain the observation. The photosynthetic bacteria contributed a significant proportion (10-60%) of the lake1s primary productivitya Direct evidence was obtained with (14C) labelling of the photosynthetic bacteria, indica.ting that the zooplankton were grazing the photosynthetic bacteria. This indicated that some of the photosynthetic bacterial productivity was assimilated into the food chain of the lake. Therefore, it was concluded that the photosynthetic bacteria made a significant contribution to the total productivity of Crawford Lake.

For the love of a barking lady: an exploration of mental illness in the light of Max Scheler's "Invisible person"

N/A

Light and electron microscope studies of host-parasite relations in a mycoparasite

Light microscope studies of the mycoparasite Piptocephalis virginiana revealed that the cylindrical spores of the parasite became spherical upon germination and produced 1-4 germ tubes. Generally t"l.vO germ tubes were produced by each spore. When this parasite was inoculated on its potential hosts, Choanephora cucurbitarum and Phascolomyces articulosus, the germ tube nearest to the host hypha continued to grow and made contact with the host hypha. The tip of the parasite's germ tube became swollen to form a distinct appressorium. Up to this stage the behavior of the parasite was similar regardless of the nature of the host. In the compatible host-parasite combination, the parasite penetrated the host, established a nutritional relationship and continued to grow to cover the host completely with its buff colored spores in 3-4 days. In the incompatible host-parasite combination, the parasite penetrated the host but its further advance was arrested. As a result of failure to establish a nutritional relationship with the resistant host, the parasite made further attempts to penetrate the host at different sites producing multiple infections. In the absence of nutrition the parasite weakened and the host outgrew the parasite completely. In the presence of a non-host species, Linderina pennispora the parasite continued to grow across the non-host 1).yp_hae vlithout establishing an initial contact. Germination studies showed that the parasite germinated equally well in the presence of host and non-host species. Further electron microscope studies revealed that the host-parasite interaction between P. virginiana and its host, C. cucurbi tarum, was compatible when the host hyphae were young slender, with a thin cell wall of one layer. The parasite appeared to penetrate mechanically by pushing the host-cell wall inward. The host plasma membrane invaginated along the involuted cell wall. The older hyphae of C. cucurbitarum possessed two distinct layers of cell wall and-showed an incompatible interaction when challenged vlith the parasite. At the point of contact, the outer layer of the host-cell wall dissolved, probably by enzymatic digestion, and the inner layer became thickened and developed a papilla as a result of its response to the parasite. The haustoria of the parasite in the old hyphae were always surrounded by a thick, well developed sheath, whereas the haustoria of the same age in the young host mycelium were devoid of a sheath during early stages of infection. Instead, they were in direct contact with the host protoplast. The incompatible interaction between a resistant host, P. articulosus and the parasite showed similar results as with the old hyphae of C. cucurbitarum. The cell wall of P. articulosus appeared thick-with two or more layers even in the 18-22 h-old hyphae. No contact or interaction was established between the parasite and the non-host L. pennispora. The role of cell wall in the resistance mechanism is discussed.

Out of the darkness and into the light : a study of inauthentic and authentic speech

Introduction Man can be described as the being who shows himself in speech, and from birth to death is continually speaking. Communication is so close to us, so woven into our very being, that we have little understanding of the way it is constituted; for it is as hard to obtain distance from communication as it is to obtain distance from ourselves. All communication is not alike. There are two basic modesl of communication, the inauthentic and the authentic, between which there occurs a constant tension. It is in the inauthentic mode, points out Heidegger, that we find ourselves "proximately and for the most part"; 1. Being and Time, pg. 68 Dasein decides as to the way it will comport itself in taking up its task of having being as an issue for it. " •.• it~, in its very being 'choose' itself and win itself; it can also lose itself and never win itself or only "seem" to do so. But only in so far as it is essentially something which can be authentic--that is, something of its own--can it have lost itself and not yet won itself." 2. therefore Heidegger also terms it "everydayness".2 Caught up in the world of everydayness, our speaking covers over and conceals3 our rootedness in being, leaving us in the darkness of untruth. The image of darkness may be inferred from Heidegger's use of the image of "clearing,,4 to depict being as 2. ibid. pg. 69 "Dasein's average everydayness, however, is not to be taken as a mere 'aspect'. Here too, and even in the mode of inauthenticity, the structure of existentiality lies ~ priori and here too Dasein's being is an issue for it in a definite way; and Dasein comports itself towards it the mode of average everydayness, even if this is only the mode of fleeing in the face of it and forgetfulness thereof." 3. ibid. pg. 59 "covering over" and "concealing" are 1;yays Dasein tries to flee its task of having being as an issue for itself. " ••• This being can be covered up so extensively that it becomes forgotten and no question arises about it or its meaning ••• n How everyday speaking accomplishes this will be taken up in detail in the second chapter which explores Dasein's everyday speech. 4. ibid, pg. 171 lI ••• we have in mind nothing other than the Existential - ontological structure of this entity (Dasein), that it is in such a way as to be its 'there'. To say that it is -' illuminated' [tlerleuchtet"] means that as Being-in-theworld it is cleared [gelichtetJ in itself7 not through any other entity, but in such a way that it is itself the clearing. Only for an entity which is eXistentially cleared in this way does what is present-at-hand become accessible in the light or hidden in the dark •••• " 3 dis-coveredness and truth. Our first task will be to explore the nature of communication in general and then to explore each of the modes manifested in turn. The structure of the inauthentic mode of communication can be explored by asking the following questions: What is this speaking about? Who is it that is speaking and who is spoken to? Does this speaking show man in his speech? The authentic mode is distinguished by the rarity with which we encounter it; as the inauthentic conceals, so the authentic reveals our rootedness in being. Yet this rarity makes it difficult to delineate its elusive structure clearly. Its constituent elements can be brought into focus by asking the same questions of this mode that we previously asked of the inauthentic mode. Our initial response to the disclosure of the authentic mode is to attempt to abandon the inauthentic mode and leave the darkness behind dwelling only in the "lighted place". All through the ages, some men pushing this to extreme, have, upon uncovering their relatedness to being, experienced a deep longing to dwell in such a "place" of pure truth and oft times denigrated or attempted to exclude the everyday world. Such 4. flight is twice mistaken: first it atbempts to fix truth as unchanging and static and secondly, it opposes this to untruth which it seeks to abolish. This is both the wrong view of truth and the wrong view of untruth as Heidegger points out in The Origin of The-Work of Art: The Way-to-be of truth, i.e., of discoveredness, is under the sway of refusal. But this refusal is no lack or privation, as if truth could be simply discoveredness rid of all covers. If it could be that, it would no longer be itself . ••• Truth in its way-to-be is untruth.5 Pure light is not the nature of Being nor is pure unconcealedness possible for man. Failure to remember this is the failure to realize that communication destroys itself in such flight because it no longer maintains the contingency of its task, i.e., the dis-closedness of being. We are reminded of the strong attraction this flight from darkness held for Plato. Light, truth and Being are all beyond the darkness and have nothing to do with it. In Book VII of the R~public, Socrates' explanation of the Allegory of the Cave to Glaucon points to a decided preference men have for the "lighted place". 5. The Origin Of The Work Of Art, pg. 42 5. Come then, I said, and join me in this further thought, and do not be surprised that those who attained to this height are not willing to occupy themselves with the affairs of men, but their souls ever feel the upward urge and yearning for that sojourn above. For this, I take it, is likely if in this point too the likeliness of our image holds. 6 Despite the attraction to pure truth, human communication is more complex than putting down one mode of communication and picking up another. Due to the fact that we are always on the way, the title of my thesis will have to be amended: OUT OF THE DARKNESS AND INTO THE LIGHT--AGAIN AND AGAIN. It must be this way because this is what it means to be human. This is the point made by Mephisto to Faust in pointing out that man, standing between God and the devil, needs both darkness and light: Er findet sich in einem ewigen Gl~t Uns hat er in die Finsternis gebracht, Und euch taugt einzig Tag und Nacht. 7 6. Republic z (517 c & d) It should be noted however, that while the philosopherking must be compelled to return to the cave for purely political reasons, once he has taken adequate view of the "brightest region of being" he has the full truth and his return to darkness adds nothing to the truth. 7. Faust, pg. 188 6. This thesis proposes to examine the grounds that give rise to communication, uncovering the structure of its inauthentic and authentic modes and paying close attention to tpeir interrelationship and to their relationship to language as "the house of Being": language that both covers and opens up man's rootedness in Being, transforming him as he moves along his way, taking up his "ownmost task" of becoming who he is. roots. He is the being who shows himself inn that reflects his forgetfulness or remembrance of his rootedness in being. Man comes into an already existent world and is addressedl through things in the world which are c