Engineering Fabric Repair Prior to Resurfacing - Roadglas - US 30, HR-525, 1992

In Iowa it is normal procedure to either use partial or full-depth patching to repair deteriorated areas of pavement prior to resurfacing. The Owens/Corning Corporation introduced a repair system to replace the patching process. Their Roadglas repair system was used in this research project on US 30 in Story County. It was installed in 1985 and has been observed annually since that time. There were some construction problems with slippage as the roller crossed the abundant Roadglas binder. It appears the Roadglas system has helped to control reflective cracking in the research areas. Since the time when this project was completed it has been reported that Owens/Corning has discontinued production of the Roadglas system.

Valganciclovir in adult solid organ transplant recipients: pharmacokinetic and pharmacodynamic characteristics and clinical interpretation of plasma concentration measurements.

Valganciclovir and ganciclovir are widely used for the prevention of cytomegalovirus (CMV) infection in solid organ transplant recipients, with a major impact on patients' morbidity and mortality. Oral valganciclovir, the ester prodrug of ganciclovir, has been developed to enhance the oral bioavailability of ganciclovir. It crosses the gastrointestinal barrier through peptide transporters and is then hydrolysed into ganciclovir. This review aims to describe the current knowledge of the pharmacokinetic and pharmacodynamic characteristics of this agent, and to address the issue of therapeutic drug monitoring. Based on currently available literature, ganciclovir pharmacokinetics in adult solid organ transplant recipients receiving oral valganciclovir are characterized by bioavailability of 66 +/- 10% (mean +/- SD), a maximum plasma concentration of 3.1 +/- 0.8 mg/L after a dose of 450 mg and of 6.6 +/- 1.9 mg/L after a dose of 900 mg, a time to reach the maximum plasma concentration of 3.0 +/- 1.0 hours, area under the plasma concentration-time curve values of 29.1 +/- 5.3 mg.h/L and 51.9 +/- 18.3 mg.h/L (after 450 mg and 900 mg, respectively), apparent clearance of 12.4 +/- 3.8 L/h, an elimination half-life of 5.3 +/- 1.5 hours and an apparent terminal volume of distribution of 101 +/- 36 L. The apparent clearance is highly correlated with renal function, hence the dosage needs to be adjusted in proportion to the glomerular filtration rate. Unexplained interpatient variability is limited (18% in apparent clearance and 28% in the apparent central volume of distribution). There is no indication of erratic or limited absorption in given subgroups of patients; however, this may be of concern in patients with severe malabsorption. The in vitro pharmacodynamics of ganciclovir reveal a mean concentration producing 50% inhibition (IC(50)) among CMV clinical strains of 0.7 mg/L (range 0.2-1.9 mg/L). Systemic exposure of ganciclovir appears to be moderately correlated with clinical antiviral activity and haematotoxicity during CMV prophylaxis in high-risk transplant recipients. Low ganciclovir plasma concentrations have been associated with treatment failure and high concentrations with haematotoxicity and neurotoxicity, but no formal therapeutic or toxic ranges have been validated. The pharmacokinetic parameters of ganciclovir after valganciclovir administration (bioavailability, apparent clearance and volume of distribution) are fairly predictable in adult transplant patients, with little interpatient variability beyond the effect of renal function and bodyweight. Thus ganciclovir exposure can probably be controlled with sufficient accuracy by thorough valganciclovir dosage adjustment according to patient characteristics. In addition, the therapeutic margin of ganciclovir is loosely defined. The usefulness of systematic therapeutic drug monitoring in adult transplant patients therefore appears questionable; however, studies are still needed to extend knowledge to particular subgroups of patients or dosage regimens.

Effect of dark chocolate on renal tissue oxygenation as measured by BOLD-MRI in healthy volunteers.

Background: Cocoa is rich in flavonoids, has anti-oxidative properties and increases the bioavailability of nitric oxide (NO). Adequate renal tissue oxygenation is crucial for the maintenance of renal function. The goal of this study was to investigate the effect of cocoa-rich dark chocolate (DC) on renal tissue oxygenation in humans, as compared to flavonoid-poor white chocolate (WC). Methods: Ten healthy volunteers with preserved kidney function (mean age ± SD 35 ± 12 years, 70% women, BMI 21 ± 3 kg/m2) underwent blood oxygenation level-dependent magnetic resonance imaging (BOLD-MRI) before and 2 hours after the ingestion of 1 g/kg of DC (70% cocoa). Renal tissue oxygenation was determined by the measurement of R2* maps on 4 coronal slices covering both kidneys. The mean R2* (= 1/T2*) values in the medulla and cortex were calculated, a low R2* indicating high tissue oxygenation. Eight participants also underwent BOLD-MRI at least 1 week later, before and 2 hours after the intake of 1 g/kg WC. Results: The mean medullary R2* was lower after DC intake compared to baseline (28.2 ± 1.3 s-1 vs. 29.6 ± 1.3 s-1, p = 0.04), whereas cortical and medullary R2* values did not change after WC intake. The change in medullary R2* correlated with the level of circulating (epi)catechines, metabolites of flavonoids (r = 0.74, p = 0.037), and was independent of plasma renin activity. Conclusion: This study suggests for the first time an increase of renal medullary oxygenation after intake of dark chocolate. Whether this is linked to flavonoid-induced changes in renal perfusion or oxygen consumption, and whether cocoa has potentially renoprotective properties, merits further study.

Three essays on major trends in a slow clockspeed industry : the case of industrial automation

The motivation for this research initiated from the abrupt rise and fall of minicomputers which were initially used both for industrial automation and business applications due to their significantly lower cost than their predecessors, the mainframes. Later industrial automation developed its own vertically integrated hardware and software to address the application needs of uninterrupted operations, real-time control and resilience to harsh environmental conditions. This has led to the creation of an independent industry, namely industrial automation used in PLC, DCS, SCADA and robot control systems. This industry employs today over 200'000 people in a profitable slow clockspeed context in contrast to the two mainstream computing industries of information technology (IT) focused on business applications and telecommunications focused on communications networks and hand-held devices. Already in 1990s it was foreseen that IT and communication would merge into one Information and communication industry (ICT). The fundamental question of the thesis is: Could industrial automation leverage a common technology platform with the newly formed ICT industry? Computer systems dominated by complex instruction set computers (CISC) were challenged during 1990s with higher performance reduced instruction set computers (RISC). RISC started to evolve parallel to the constant advancement of Moore's law. These developments created the high performance and low energy consumption System-on-Chip architecture (SoC). Unlike to the CISC processors RISC processor architecture is a separate industry from the RISC chip manufacturing industry. It also has several hardware independent software platforms consisting of integrated operating system, development environment, user interface and application market which enables customers to have more choices due to hardware independent real time capable software applications. An architecture disruption merged and the smartphone and tablet market were formed with new rules and new key players in the ICT industry. Today there are more RISC computer systems running Linux (or other Unix variants) than any other computer system. The astonishing rise of SoC based technologies and related software platforms in smartphones created in unit terms the largest installed base ever seen in the history of computers and is now being further extended by tablets. An underlying additional element of this transition is the increasing role of open source technologies both in software and hardware. This has driven the microprocessor based personal computer industry with few dominating closed operating system platforms into a steep decline. A significant factor in this process has been the separation of processor architecture and processor chip production and operating systems and application development platforms merger into integrated software platforms with proprietary application markets. Furthermore the pay-by-click marketing has changed the way applications development is compensated: Three essays on major trends in a slow clockspeed industry: The case of industrial automation 2014 freeware, ad based or licensed - all at a lower price and used by a wider customer base than ever before. Moreover, the concept of software maintenance contract is very remote in the app world. However, as a slow clockspeed industry, industrial automation has remained intact during the disruptions based on SoC and related software platforms in the ICT industries. Industrial automation incumbents continue to supply systems based on vertically integrated systems consisting of proprietary software and proprietary mainly microprocessor based hardware. They enjoy admirable profitability levels on a very narrow customer base due to strong technology-enabled customer lock-in and customers' high risk leverage as their production is dependent on fault-free operation of the industrial automation systems. When will this balance of power be disrupted? The thesis suggests how industrial automation could join the mainstream ICT industry and create an information, communication and automation (ICAT) industry. Lately the Internet of Things (loT) and weightless networks, a new standard leveraging frequency channels earlier occupied by TV broadcasting, have gradually started to change the rigid world of Machine to Machine (M2M) interaction. It is foreseeable that enough momentum will be created that the industrial automation market will in due course face an architecture disruption empowered by these new trends. This thesis examines the current state of industrial automation subject to the competition between the incumbents firstly through a research on cost competitiveness efforts in captive outsourcing of engineering, research and development and secondly researching process re- engineering in the case of complex system global software support. Thirdly we investigate the industry actors', namely customers, incumbents and newcomers, views on the future direction of industrial automation and conclude with our assessments of the possible routes industrial automation could advance taking into account the looming rise of the Internet of Things (loT) and weightless networks. Industrial automation is an industry dominated by a handful of global players each of them focusing on maintaining their own proprietary solutions. The rise of de facto standards like IBM PC, Unix and Linux and SoC leveraged by IBM, Compaq, Dell, HP, ARM, Apple, Google, Samsung and others have created new markets of personal computers, smartphone and tablets and will eventually also impact industrial automation through game changing commoditization and related control point and business model changes. This trend will inevitably continue, but the transition to a commoditized industrial automation will not happen in the near future.

Diurnal inhibition of NMDA-EPSCs at rat hippocampal mossy fibre synapses through orexin-2 receptors.

Diurnal release of the orexin neuropeptides orexin-A (Ox-A, hypocretin-1) and orexin-B (Ox-B, hypocretin-2) stabilises arousal, regulates energy homeostasis and contributes to cognition and learning. However, whether cellular correlates of brain plasticity are regulated through orexins, and whether they do so in a time-of-day-dependent manner, has never been assessed. Immunohistochemically we found sparse but widespread innervation of hippocampal subfields through Ox-A- and Ox-B-containing fibres in young adult rats. The actions of Ox-A were studied on NMDA receptor (NMDAR)-mediated excitatory synaptic transmission in acute hippocampal slices prepared around the trough (Zeitgeber time (ZT) 4-8, corresponding to 4-8 h into the resting phase) and peak (ZT 23) of intracerebroventricular orexin levels. At ZT 4-8, exogenous Ox-A (100 nm in bath) inhibited NMDA receptor-mediated excitatory postsynaptic currents (NMDA-EPSCs) at mossy fibre (MF)-CA3 (to 55.6 ± 6.8% of control, P = 0.0003) and at Schaffer collateral-CA1 synapses (70.8 ± 6.3%, P = 0.013), whereas it remained ineffective at non-MF excitatory synapses in CA3. Ox-A actions were mediated postsynaptically and blocked by the orexin-2 receptor (OX2R) antagonist JNJ10397049 (1 μm), but not by orexin-1 receptor inhibition (SB334867, 1 μm) or by adrenergic and cholinergic antagonists. At ZT 23, inhibitory effects of exogenous Ox-A were absent (97.6 ± 2.9%, P = 0.42), but reinstated (87.2 ± 3.3%, P = 0.002) when endogenous orexin signalling was attenuated for 5 h through i.p. injections of almorexant (100 mg kg(-1)), a dual orexin receptor antagonist. In conclusion, endogenous orexins modulate hippocampal NMDAR function in a time-of-day-dependent manner, suggesting that they may influence cellular plasticity and consequent variations in memory performance across the sleep-wake cycle.

Implantació d'una plataforma informàtica en una entitat financera fusionada

Els darrers anys han estat molt convulsos en el món financer. De tots és coneguda la crisi, immobiliària en un primer moment, i financera més tard. Reestructuracions, fusions, absorcions, intervencions i nacionalitzacions han estat a l’ordre del dia en el món de les entitats financeres els últims 3 anys. El mapa financer ha passat de més de 50 entitats a poc menys de 10 en tan sols 3 anys. Els departaments de tecnologia de bancs i caixes no han estat aliens a aquests moviments. Tot i estar relativament al marge del negoci financer de l’entitat, cada fusió ha atorgat un paper protagonista a tota la plantilla informàtica. Ja que cada reestructuració ha suposat un gran esforç per integrar entitats molt diferents entre si en una de sola. Intentant que l’impacte a clients i a usuaris fos el menor possible. Caixa Manlleu és un exemple proper de la reestructuració del món financer, i ha protagonitzat, juntament amb Caixa Sabadell i Caixa Terrassa, la creació d’Unnim. Aquest cas real serà la base del treball. El projecte consisteix en la creació d’una plataforma informàtica per a la nova entitat resultant de la fusió. Una plataforma amb un doble objectiu: d’una banda, que reculli el millor de les tres plataformes d’origen i que compleixi tots els requestis que la nova entitat exigeix per tal que els usuaris puguin continuar fent les tasques diàries. I de l’altra, una plataforma que posi al dia i actualitzi tecnològicament l’entitat amb el mínim cost possible. Així doncs, cal analitzar per separat cadascuna de les 3 plataformes existents, inventariar les aplicacions comunes i les departamentals, així com les llicències de software vigents existents i no caducades. Decidir quines aplicacions es faran servir, si se’n poden aprofitar o si per contra en calen de noves. També cal analitzar quins equips informàtics (terminals) es necessitaran per tal de treure el màxim rendiment de la plataforma. Entre les conclusions obtingudes en el projecte, cal destacar els grans avantatges d’utilitzar aplicacions virtualitzades en lloc de les tradicionals aplicacions instal·lades físicament a cada terminal. Faciliten la feina i el manteniment, estalvien recursos i fan guanyar temps. A més a més s’aconsegueix una plataforma àgil, lleugera i ràpida.

Personalized touristic routes implementing semantic web on GIS

Nowadays, when a user is planning a touristic route is very difficult to find out which are the best places to visit. The user has to choose considering his/her preferences due to the great quantity of information it is possible to find in the web and taking into account it is necessary to do a selection, within small time because there is a limited time to do a trip. In Itiner@ project, we aim to implement Semantic Web technology combined with Geographic Information Systems in order to offer personalized touristic routes around a region based on user preferences and time situation. Using ontologies it is possible to link, structure, share data and obtain the result more suitable for user's preferences and actual situation with less time and more precisely than without ontologies. To achieve these objectives we propose a web page combining a GIS server and a touristic ontology. As a step further, we also study how to extend this technology on mobile devices due to the raising interest and technological progress of these devices and location-based services, which allows the user to have all the route information on the hand when he/she does a touristic trip. We design a little application in order to apply the combination of GIS and Semantic Web in a mobile device.

A wearable system to time gate crossing during alpine skiing slalom

INTRODUCTION: In alpine skiing, chronometry analysis is currently the most common tool to assess performance. It is widely used to rank competitors during races, as well as to manage athletes training and to evaluate material. Usually, this measurement is accurately realized using timing cells. Nevertheless, these devices are too complex and expensive to allow chronometry of every gates crossing. On the other side, differential GPS can be used for measuring gate crossing time (Waegli et al). However, this is complex (e.g. recording gate position with GPS) and mainly used in research applications. The aim of the study was to propose a wearable system to time gates crossing during alpine skiing slalom (SL), which is suitable for routine uses. METHODS: The proposed system was composed of a 3D accelerometer (ADXL320®, Analog Device, USA) placed at the sacrum of the athlete, a matrix of force sensors (Flexiforce®, Tekscan, USA) fixed on the right shin guard and a data logger (Physilog®, BioAGM, Switzerland). The sensors were sampled at 500 Hz. The crossing time were calculated in two phases. First, the accelerometer was used to detect the curves by considering the maximum of the mediolateral peak acceleration. Then, the force sensors were used to detect the impacts with the gates by considering maximum force variation. In case of non impact, the detection was realized based on the acceleration and features measured at the other gates. In order to assess the efficiency of the system, two different SL were monitored twice for two world cup level skiers, a male SL expert and a female downhill expert. RESULTS AND DISCUSSION: The combination of the accelerometer and force sensors allowed to clearly identify the gate crossing times. When comparing the runs of the SL expert and the downhill expert, we noticed that the SL expert was faster. For example for the first SL, the overall difference between the best run of each athlete was of 5.47s. At each gate, the SL expert increased the time difference slower at the beginning (0.27s/gate) than at the end (0.34s/gate). Furthermore, when comparing the runs of the SL expert, a maximum time difference of 20ms at each gate was noticed. This showed high repeatability skills of the SL expert. In opposite, the downhill expert with a maximum difference time of 1s at each gate was clearly less repeatable. Both skiers were not disturbed by the system. CONCLUSION: This study proposed a new wearable system to automatically time gates crossing during alpine skiing slalom combining force and accelerometer sensors. The system was evaluated with two professional world cup skiers and showed a high potential. This system could be extended to time other parameters. REFERENCES Waegli A, Skaloud J (2007). Inside GNSS, Spring, 24-34.

Development of a simulation tool for torsional vibration of branched power transmission system

In this master's thesis a mechanical model that is driven with variable speed synchronous machine was developed. The developed mechanical model simulates the mechanics of power transmission and its torsional vibrations. The mechanical model was developed for the need of the branched mechanics of a rolling mill and the propulsion system of a tanker. First, the scope of the thesis was to clarify the concepts connected to the mechanical model. The clarified concepts are the variable speed drive, the mechanics of power transmission and the vibrationsin the power transmission. Next, the mechanical model with straight shaft line and twelve moments of inertia that existed in the beginning was developed to be branched considering the case of parallel machines and the case of parallel rolls. Additionally, the model was expanded for the need of moreaccurate simulation to up to thirty moments of inertia. The model was also enhanced to enable three phase short circuit situation of the simulated machine. After that the mechanical model was validated by comparing the results of the developed simulation tool to results of other simulation tools. The compared results are the natural frequencies and mode shapes of torsional vibration, the response of the load torque step and the stress in the mechanical system occurred by the permutation of the magnetic field that is arisen from the three phase short circuit situation. The comparisons were accomplished well and the mechanical model was validated for the compared cases. Further development to be made is to develop the load torque to be time-dependent and to install two frequency converters and two FEM modeled machines to be simulated parallel.

La flexibilité du temps de travail: entre autonomie et contraintes. Une étude de cas en Suisse.

Flexitime : between autonomy and constraints. A case study in SwitzerlandBy looking at how a new regulation is translated into everyday practices, this dissertation explores through a specific case study the degree of autonomy gained by wage-earners with the introduction of flexible working schedules. The guiding hypothesis is that by introducing procedural rules, flexitime opens the space for more daily negotiations, therefore reinforcing the effects of power relations inherent to employment relationships. The goal is to understand, through a sociological approach, how employees experience a form of working time that transfers responsibility for time management to them, and howthey integrate work-related constraints with their life outside the workplace. The first part of the dissertation sets up the context of the case study. It offers a definition of flexibility by situating it in the broader history of work time, as well as in relation to various organizational forms and cultural transformations. An international literature review and a focus on the Swiss case are offered. In the second part, the focus is narrowed to a specificSwiss firm specialized in mail-order, where a system of individualized management of annual work time has been introduced. By combining a quantitative and qualitative approach, it is possible to analyze determinants of the practices internal to the firm anddeterminants related to employees themselves, as well as the way in which employees articulate these two orders of constraints. The results show that the implementation of flexible working time is not affecting daily negotiation practices so much as it is creating a set of informal rules. The autonomy ofwage-earners is expressed first and foremost through their capacity to produce, negotiate, and legitimate these rules. The intraindividual level has proven to be central for the social regulation of flexible working time. It is not so much a question of legitimation, but rather the process of institutionalization nurtured by the energy invested by wage-earners in their personal quest for a compromise between their various roles, identities, and aspirations. It is this individualized regulation that is ensuring the success of the system under study.

Cryo-electron microscopy of vitreous sections of native biological cells and tissues : methodology and applications

Résumé L'eau est souvent considérée comme une substance ordinaire puisque elle est très commune dans la nature. En fait elle est la plus remarquable de toutes les substances. Sans l'eau la vie sur la terre n'existerait pas. L'eau représente le composant majeur de la cellule vivante, formant typiquement 70 à 95% de la masse cellulaire et elle fournit un environnement à d'innombrables organismes puisque elle couvre 75% de la surface de terre. L'eau est une molécule simple faite de deux atomes d'hydrogène et un atome d'oxygène. Sa petite taille semble en contradiction avec la subtilité de ses propriétés physiques et chimiques. Parmi celles-là, le fait que, au point triple, l'eau liquide est plus dense que la glace est particulièrement remarquable. Malgré son importance particulière dans les sciences de la vie, l'eau est systématiquement éliminée des spécimens biologiques examinés par la microscopie électronique. La raison en est que le haut vide du microscope électronique exige que le spécimen biologique soit solide. Pendant 50 ans la science de la microscopie électronique a adressé ce problème résultant en ce moment en des nombreuses techniques de préparation dont l'usage est courrant. Typiquement ces techniques consistent à fixer l'échantillon (chimiquement ou par congélation), remplacer son contenu d'eau par un plastique doux qui est transformé à un bloc rigide par polymérisation. Le bloc du spécimen est coupé en sections minces (d’environ 50 nm) avec un ultramicrotome à température ambiante. En général, ces techniques introduisent plusieurs artefacts, principalement dû à l'enlèvement d'eau. Afin d'éviter ces artefacts, le spécimen peut être congelé, coupé et observé à basse température. Cependant, l'eau liquide cristallise lors de la congélation, résultant en une importante détérioration. Idéalement, l'eau liquide est solidifiée dans un état vitreux. La vitrification consiste à refroidir l'eau si rapidement que les cristaux de glace n'ont pas de temps de se former. Une percée a eu lieu quand la vitrification d'eau pure a été découverte expérimentalement. Cette découverte a ouvert la voie à la cryo-microscopie des suspensions biologiques en film mince vitrifié. Nous avons travaillé pour étendre la technique aux spécimens épais. Pour ce faire les échantillons biologiques doivent être vitrifiés, cryo-coupées en sections vitreuse et observées dans une cryo-microscope électronique. Cette technique, appelée la cryo- microscopie électronique des sections vitrifiées (CEMOVIS), est maintenant considérée comme étant la meilleure façon de conserver l'ultrastructure de tissus et cellules biologiques dans un état très proche de l'état natif. Récemment, cette technique est devenue une méthode pratique fournissant des résultats excellents. Elle a cependant, des limitations importantes, la plus importante d'entre elles est certainement dû aux artefacts de la coupe. Ces artefacts sont la conséquence de la nature du matériel vitreux et le fait que les sections vitreuses ne peuvent pas flotter sur un liquide comme c'est le cas pour les sections en plastique coupées à température ambiante. Le but de ce travail a été d'améliorer notre compréhension du processus de la coupe et des artefacts de la coupe. Nous avons ainsi trouvé des conditions optimales pour minimiser ou empêcher ces artefacts. Un modèle amélioré du processus de coupe et une redéfinitions des artefacts de coupe sont proposés. Les résultats obtenus sous ces conditions sont présentés et comparés aux résultats obtenus avec les méthodes conventionnelles. Abstract Water is often considered to be an ordinary substance since it is transparent, odourless, tasteless and it is very common in nature. As a matter of fact it can be argued that it is the most remarkable of all substances. Without water life on Earth would not exist. Water is the major component of cells, typically forming 70 to 95% of cellular mass and it provides an environment for innumerable organisms to live in, since it covers 75% of Earth surface. Water is a simple molecule made of two hydrogen atoms and one oxygen atom, H2O. The small size of the molecule stands in contrast with its unique physical and chemical properties. Among those the fact that, at the triple point, liquid water is denser than ice is especially remarkable. Despite its special importance in life science, water is systematically removed from biological specimens investigated by electron microscopy. This is because the high vacuum of the electron microscope requires that the biological specimen is observed in dry conditions. For 50 years the science of electron microscopy has addressed this problem resulting in numerous preparation techniques, presently in routine use. Typically these techniques consist in fixing the sample (chemically or by freezing), replacing its water by plastic which is transformed into rigid block by polymerisation. The block is then cut into thin sections (c. 50 nm) with an ultra-microtome at room temperature. Usually, these techniques introduce several artefacts, most of them due to water removal. In order to avoid these artefacts, the specimen can be frozen, cut and observed at low temperature. However, liquid water crystallizes into ice upon freezing, thus causing severe damage. Ideally, liquid water is solidified into a vitreous state. Vitrification consists in solidifying water so rapidly that ice crystals have no time to form. A breakthrough took place when vitrification of pure water was discovered. Since this discovery, the thin film vitrification method is used with success for the observation of biological suspensions of. small particles. Our work was to extend the method to bulk biological samples that have to be vitrified, cryosectioned into vitreous sections and observed in cryo-electron microscope. This technique is called cryo-electron microscopy of vitreous sections (CEMOVIS). It is now believed to be the best way to preserve the ultrastructure of biological tissues and cells very close to the native state for electron microscopic observation. Since recently, CEMOVIS has become a practical method achieving excellent results. It has, however, some sever limitations, the most important of them certainly being due to cutting artefacts. They are the consequence of the nature of vitreous material and the fact that vitreous sections cannot be floated on a liquid as is the case for plastic sections cut at room temperature. The aim of the present work has been to improve our understanding of the cutting process and of cutting artefacts, thus finding optimal conditions to minimise or prevent these artefacts. An improved model of the cutting process and redefinitions of cutting artefacts are proposed. Results obtained with CEMOVIS under these conditions are presented and compared with results obtained with conventional methods.

Agendi Modus; Yrittäjyyskasvatusta Etelä-Karjalassa. Yrittäjyys, koulut ja yrittäjyyskasvatuksenhanketoiminta

Julkaisu on kuvaus Agendi Modus - yrittäjyyskasvatushankkeesta, joka toteutettiin Etelä- Karjalassa vuosina 2004-2007. Samalla se on hankkeeseen osallistuneiden kokemuksista tehty vaikuttavuuden arviointiraportti. Agendi Modus-hanke oli Lappeenrannan teknillisen yliopiston Koulutus ja kehittämiskeskuksen kouluille ja yrityksille suunnattu projekti. Hankkeen tavoitteet olivat 1. pedagogisen muutoksen tuottaminen, 2. oppimisympäristöjen kehittäminen ja 3. yrittäjämäistä koulutyötä tukevan koulun kulttuurin ja johtamisen muutoksen tuottaminen. Julkaisusta käy ilmi, että hankevoi oppia yhdessä asiakkaidensa eli hankkeen yhteistyötahojen kanssa. Raportin toisessa osassa tuodaan esille muutamia yrittäjyyskasvatuksen näkökulmia. Lukija voi myös pohtia, tulisiko yrittäjyyskasvatuksen koulutuskokonaisuus rakentua kuten Agendi Moduksessa, eli esitellen aihealuetta sekäyleisesti että perehtyen sen eri olemuspuoliin. Julkaisun keskeisimmät huomiot ovat että A) hanke, joka kuuntelee asiakastaan, tuottaa sen tarvitsemia tuotteita, B) pitkäkestoinen koulutusprosessi tarjoaa mahdollisuuden ymmärtää yrittäjyyskasvatuksen metodologiaa ja pedagogiaa ja tukee aihealueen didaktiikan kokeilemista, C) on tärkeää kouluttaa sekä työyhteisöjä että näiden yksittäisiä toimijoita, D) eri osallistujilla on omanlaistaan osaamista yrittäjyyskasvatuksessa, koska kukin on valinnut erityyppistä koulutuksista itselleen soveltuvimpia, E) näyttää siltä, että noin puolet koulutuksiin osallistuneista käyttää yrittäjyyskasvatusta opetuksensa käyttöteoriana, F) oppimisympäristöjen kehittäminen on vähäisempää kuin yrittäjyyskasvatuksen käyttö oman opetuksen osana, G) hankkeen jälkeen osallistujilla on laaja ymmärrys yrittäjyyskasvatusta suosivasta oppimiskulttuurista, mutta vain harvat kokevat luovansa yrittäjämäistä koulukulttuuria. Jos uutta aihealueen hanketta suunnitellaan, se voisi keskittyä tätä hanketta tarkemmin koulukulttuurin muuttamiseen, jonka lisäksi toiminta-ajatuksissa kannattaisi huomioida oppimisen, teknologian ja yrittäjyyden strategiat.

Immunology of viral disease, how to curb persistent infection

1. 1. Summaries 1.1. Preamble and extended abstract The present thesis dissertation addresses the question of antiviral immunity from the particular standpoint of the adaptive T cell-mediated immune response. The experimental work is presented in the form of three published articles (two experimental articles and one review article, see sections 4.1, 4.2 and 4.3 on pages 73, 81 and 91, respectively), describing advances both in our understanding of viral control by CD8 T lymphocytes, and in vaccine development against the Human Immunodeficiency Virus Type 1 (HIV-1). Because the articles focus on rather specialized areas of antiviral immunity, the article sections are preceded by a general introduction (section 3) on the immune system in general, and on four viruses that were addressed in the experimental work, namely HIV-1, Cytomegalovirus (CMV), Epstein Barr Virus (EBV) and Influenzavirus (Flu). This introduction section is aimed at providing a glimpse on viral molecular biology and immunity, to help the hypothetical non-expert reader proceeding into the experimental part. For this reason, each section is presented as individual entity and can be consulted separately. The four viruses described are of peculiar relevance to immunity because they induce an array of opposite host responses. Flu causes a self limiting disease after which the virus is eradicated. CMV and EBV cause pauci-symptomatic or asymptomatic diseases after which the viruses establish lifelong latency in the host cells, but are kept in check by immunity. Eventually, HIV-1 establishes both latency - by inserting its genome into the host cell chromosome - and proceeds in destroying the immune system in a poorly controlled fashion. Hence, understanding the fundamental differences between these kinds of viral host interactions might help develop new strategies to curb progressive diseases caused by viruses such as HIV-1. Publication #1: The first article (section 4.1, page 73) represents the main frame of my laboratory work. It analyses the ability of CD8 T lymphocytes recovered from viral-infected patients to secrete interferon γ (IFN-γ) alone or in conjunction with interleukin 2 (IL-2) when exposed in vitro to their cognate viral antigens. CD8 T cells are instrumental in controlling viral infection. They can identify infected cells by detecting viral antigens presented at the surface of the infected cells, and eliminate both the cell and its infecting virus by triggering apoptosis and/or lysis of the infected cell. Recognition of these antigens triggers the cognate CD8 cells to produce cytokines, including IFN-γ and IL-2, which in turn attract and activate other pro-inflammatory cells. IFN-γ triggers both intrinsic antiviral activity of the infected cells and distant activation of pro-inflammatory cells, which are important for the eradication of infection. IL-2 is essential for clonal expansion of the antigen (Ag)-specific CD8 T cell. Hence the existence of Ag-specific CD8 cells secreting both IFN-γand IL-2 should be beneficial for controlling infection. In this first work we determined the percentage of IFN-y/IL-2 double positive and single IFN-γsecreting CD8 T cells against antigens HIV-1, CMV, EBV and Flu in three groups of subjects: (i) HIV-1 infected patients progressing to disease (progressors), (ii) HIV-1-infected subjects not progressing to disease (long-term non progressors or LTNP), and (iii) HIV negative blood donors. The results disclosed a specific IFN-y/IL-2 double positive CD8 response in all subjects able to control infection. In other words, IFN-y/IL-2 double positive CD8 cells were present in virus-specific CD8 T cells against Flu, CMV and EBV as well against HIV-1 in LTNP. In contrast, progressors only had single IFN-γsecreting CD8 T cells. Hence, the ability to develop an IFN-y/IL-2 double positive response might be critical to control infection, independently of the nature of the virus. Additional experiments helped identify the developmental stage of the missing cells (using different markers such as CD45RA and CCR7) and showed a correlation between the absence of IL-2 secreting CD8 T cells and a failure in the proliferation capacity of virus-specific CD8 T cells. Addition of exogenous IL-2 could restore clonal expansion of HIV-1 specific CD8 T cells, at least in vitro. It could further been shown, that IL-2 secreting CD8 T cells are sufficient to support proliferation even in absence of CD4 help. However, the reason for the missing IFN-y/IL-2 double positive CD8 T cell response in HIV-1 progessors has yet to be determined. Publication #2: The second article (section 4.2, page 81) explores new strategies to trigger CD8 T cell immunity against specific HIV-1 proteins believed to be processed and exposed as "infection signal" at the surface of infected cells. Such signals consist of peptide fragments (8- 13 amino acids) originating from viral proteins and presented to CD8 T cells in the frame of particular cell surface molecules of the major histocompatibility complex class I* (MHC I). To mimic "natural" viral infection, the HIV-1 polyprotein Gagpolnef was inserted and expressed in either of two attenuated viruses i.e. vaccinia virus (MVA) or poxvirus (NYVAC). Mice were infected with these recombinant viruses and specific CD8 T cell response to Gagpolnef peptides was sought. Mice could indeed mount a CD8 T cell response against the HIV-1 antigens, indicating that the system worked, at least in this animal model. To further test whether peptides from Gagpolnef could also be presented in the frame of the human MHC class I proteins, a second round of experiments was performed in "humanized" transgenic mice expressing human MHC molecules. The transgenic mice were also able to load Gagpolnef peptides on their human MHC molecule, and these cells could be detected and destroyed by Ag-specific CD8 T cells isolated from HIV-1-infected patients. Therefore, expressing Gagpolnef on attenuated recombinant viruses might represent a valid strategy for anti-HIV-1 immunization in human. Publication #3: This is a review paper (section 4.3, page 91) describing the immune response to CMV and newly developed methods to detect this cellular immune response. Some of it focuses on the detection of T cells by using in vitro manufactured tetramers. These consist of four MHC class I molecules linked together and loaded with the appropriate antigenic peptide. The tetramer can be labeled with a fluorochrome and analyzed with a fluorescence-activated cell sorter. Taken together, the work presented indicates that (i) an appropriate CD8 T cell response consisting of IFN-y/IL-2 double positive effectors, can potentially control viral infection, including HIV-1 infection, (ii) such a response might be triggered by recombinant viral vaccines, and (iii) CD8 T cell response can be monitored by a variety of techniques, including recently-developed MHC class I tetramers. 1. 2. Préambule et résumé élargi Le présent travail de thèse s'intéresse à l'immunité antivirale du point de vue particulier de la réponse adaptative des cellules T. Le travail expérimental est présenté sous la forme de trois articles publiés (2 articles expérimentaux et 1 article de revue, voir sections 4.1, 4.2 et 4.3, pages 58, 66 et 77, respectivement), décrivant des progrès dans la compréhension du contrôle de l'infection virale par les lymphocytes T CD8, ainsi que dans le développement de nouveaux vaccins contre le Virus d'Immunodéficience de Humaine de type 1 (VIH-1). En raison du caractère spécialisé de l'immunité antivirale de type cellulaire, les articles sont précédés par une introduction générale (section 3), dont le but est de pourvoir le lecteur non avisé avec des bases nécessaire à une meilleure appréhension du travail expérimental. Cette introduction présente les grandes lignes du système immunitaire, et décrit de façon générale les 4 virus utilisés dans le travail expérimental: à savoir le virus VIH-1, le Cytomégalovirus (CMV), le virus Epstein Barr (EBV) et le virus Influenza A (Flu). Toutes les sections sont présentées de façon individuelle et peuvent être consultées séparément. La description des 4 virus a une pertinence particulière quant à leur interaction avec le système immun. En effet, ils induisent une panoplie de réponses immunitaires s'étendant aux extrêmes de la réaction de l'hôte. Influenza A est à l'origine d'une maladie cytopathique aiguë, au décours de laquelle le virus est éradiqué par l'hôte. CMV et EBV sont classiquement à l'origine d'infections pauci-symptomatiques, voire asymptomatiques, après lesquelles les virus persistent de façon latente dans la cellule hôte. Cependant, ils restent sous le contrôle du système immun, qui peut prévenir une éventuelle réactivation. Enfin, VIH-1 s'établit à la fois en infection latente - par l'insertion de son génome dans le chromosome des cellules hôtes - et en infection productive et cytopathique, échappant au contrôle immunitaire et détruisant ses cellules cibles. La compréhension des différences fondamentales entre ces différents types d'interactions virus-hôte devraient faciliter le développement de nouvelles stratégies antivirales. Article 1: Le premier article (section 4.1 Page 58) représente l'objet principal de mon travail de laboratoire. Il analyse la capacité des lymphocytes T CD8 spécifiques de différent virus à sécréter de l'interféron gamma (IFN-y) et/ou de l'interleukine 2 (IL-2) après stimulation par leur antigène spécifique. Les cellules T CD8 jouent un rôle crucial dans le contrôle des infections virales. Elles identifient les cellules infectées en détectant des antigènes viraux présentés à la surface de ces mêmes cellules, et éliminent à la fois les cellules infectées et les virus qu'elles contiennent en induisant l'apoptose et/ou la lyse des cellules cibles. Parallèlement, l'identification de l'antigène par la cellule T CD8 la stimule à sécréter des cytokines. L'IFN-γen est un exemple. L'IFN-γ stimule les cellules infectées à développer une activé antivirale intrinsèque. De plus, il attire sur place d'autres cellules de l'inflammation, et active leur fonction d'éradication des pathogènes. L'IL-2 est un autre exemple. L'IL-2 est essentielle à l'expansion clonale des cellules T CD8 spécifiques à un virus donné. Elle est donc essentielle à augmenter le pool de lymphocytes antiviraux. En conséquence, la double capacité de sécréter de l'IFN-γ et de IL-2 pourrait être un avantage pour le contrôle antiviral par les cellules T CD8. Dans ce travail nous avons comparé les proportions de lymphocytes T CD8 doubles positifs (IFN-γ/IL-2) et simples positifs (IFN-γ) chez trois groupes de sujets: (i) des patients infectés par VIH-1 qui ne contrôlent pas l'infection (progresseurs), (ii) des patients infectés par VIH-1, mais contrôlant l'infection malgré l'absence de traitement ("long term non progressors" [LTNP]) et (iii) des donneurs de sang négatifs pour l'infection à VIH-1. Les résultats ont montré que les individus capables de contrôler une infection possédaient des cellules T CD8 doubles positifs (IFN-γ/IL-2), alors que les patients ne contrôlant pas l'infection procédaient prioritairement des CD8 simples positifs (IFN-γ). Spécifiquement, les lymphocytes T spécifiques pour Flu, CMV, EBV, et VII-1-1 chez les LTNP étaient tous IFN-γ/IL-2 doubles positifs. Au contraire, les lymphocytes T CD8 spécifique à VIH-1 étaient IFN-γ simples positifs chez les progresseurs. La capacité de développer une réponse IFN-γ/IL-2 pourraient être primordiale pour le contrôle de l'infection, indépendamment de la nature du virus. En effet, il a été montré que l'absence de sécrétion d'IL2 par les lymphocytes T CD8 corrélait avec leur incapacité de proliférer. Dans nos mains, cette prolifération a pu être restaurée in vitro par l'adjonction exogène d'IL-2. Toutefois, la faisabilité de ce type de complémentation in vivo n'est pas claire. Des expériences additionnelles ont permis de préciser de stade de développement des lymphocytes doubles positifs et simples positifs par le biais des marqueurs CD45RA et CCR7. Il reste maintenant à comprendre pourquoi certains lymphocytes T CD8 spécifiques sont incapables à sécréter de l'IL-2. Article 2: Le deuxième article explore des nouvelles stratégies pour induire une immunité T CD8 spécifique aux protéines du VIH-1, qui sont édités et exposés à la surface des cellules infectées. Ces signaux consistent en fragments de peptide de 8-13 acide aminés provenant de protéines virales, et exposées à la surface des cellules infectées dans le cadre des molécules spécialisées d'histocompatibilité de classe I (en anglais "major histocompatibility class I" ou MHC I). Pour mimer une infection virale, la polyprotéine Gagpolnef du VIH-1 a été insérée et exprimée dans deux vecteurs viraux atténués, soit MVA (provenant de vaccinia virus) ou NYVAC (provenant d'un poxvirus). Ensuite des souris ont été infectées avec ces virus recombinants et la réponse T CD8 aux peptides issus de Gagpolnef a été étudiée. Les souris ont été capables de développer une réponse de type CD8 T contre ces antigènes du VIH-1. Pour tester si ces antigènes pouvaient aussi être présentés par dans le cadre de molécules MHC humaines, des expériences supplémentaires ont été faites avec des souris exprimant un MHC humain. Les résultats de ces manipulations ont montré que des cellules T CD8 spécifique aux protéines du VIH pouvaient être détectées. Ce travail ouvre de nouvelles options quant à l'utilisation des virus recombinants exprimant Gagpolnef comme stratégie vaccinale contre le virus VIH-I chez l'homme. Article 3: Ces revues décrivent la réponse immunitaire à CMV ainsi que des nouvelles méthodes pouvant servir à sa détection. Une partie du manuscrit décrit la détection de cellule T à l'aide de tétramères. Il s'agit de protéines chimériques composées de 4 quatre molécules MHC liées entre elles. Elles sont ensuite "chargées" avec le peptide antigénique approprié, et utilisée pour détecter les cellules T CD8 spécifiques à ce montage. Elles sont aussi marquées par un fluorochrome, qui permet une analyse avec un cytomètre de flux, et l'isolement ultime des CD8 d'intérêt. En résumé, le travail présenté dans cette thèse indique que (i) une réponse T CD8 appropriée - définie par la présence des cellules effectrices doublement positives pour l'IFN-γ et l'IL-2 - semble indispensable pour le contrôle des infections virales, y compris par le VIH-1, (ii) une telle réponse peut être induite par des vaccin viral recombinant, et (iii) la réponse T CD8 peut être analysée et suivie grâce à plusieurs techniques, incluant celle des tétramères de MHC class I. 1.3. Résumé pour un large public Le système immunitaire humain est composé de différents éléments (cellules, tissus et organes) qui participent aux défenses de l'organisme contre les pathogènes (bactéries, virus). Parmi ces cellules, les lymphocytes T CD8, également appelés cellules tueuses, jouent un rôle important dans la réponse immunitaire et le contrôle des infections virales. Les cellules T CD8 reconnaissent de manière spécifique des fragments de protéines virales qui sont exposés à la surface des cellules infectées par le virus. Suite à cette reconnaissance, les cellules T CD8 sont capables de détruire et d'éliminer ces cellules infectées, ainsi que les virus qu'elles contiennent. Dans le contexte d'une infection par le virus de l'immunodéficience humaine (VIH), le virus responsable du SIDA, il a pu être montré que la présence des cellules T CD8 est primordiale. En effet, en l'absence de ces cellules, les individus infectés par le VIH progressent plus rapidement vers le SIDA. Au cours de la vie, l'Homme est exposé à plusieurs virus. Mais à l'opposé du VIH, certains d'entre eux ne causent pas des maladies graves : par exemple le virus de la grippe (Influenza), le cytomégalovirus ou encore le virus d'Epstein-Barr. Certains de ces virus peuvent être contrôlés et éliminés de l'organisme (p. ex. le virus de la grippe), alors que d'autres ne sont que contrôlés par notre système immunitaire et restent présents en petite quantité dans le corps sans avoir d'effet sur notre santé. Le sujet de mon travail de thèse porte sur la compréhension du mécanisme de contrôle des infections virales par le système immunitaire : pourquoi certains virus peuvent être contrôlés ou même éliminés de l'organisme alors que d'autres, et notamment le VIH, ne le sont pas. Ce travail a permis de démontrer que les cellules T CD8 spécifiques du VIH ne sécrètent pas les mêmes substances, nécessaires au développement d'une réponse antivirale efficace, que les cellules T CD8 spécifiques des virus contrôlés (le virus de la grippe, le cytomégalovirus et le virus d'Epstein-Barr). Parallèlement nous avons également observé que les lymphocytes T CD8 spécifiques du VIH ne possèdent pas la capacité de se diviser. Ils sont ainsi incapables d'être présents en quantité suffisante pour assurer un combat efficace contre le virus du SIDA. La (les) différence(s) entre les cellules T CD8 spécifiques aux virus contrôlés (grippe, cytomégalovirus et Epstein-Barr) et au VIH pourront peut-être nous amener à comprendre comment restaurer une immunité efficace contre ce dernier.

Three essays on short-term macroeconomics : business fluctuations, large devaluations and inflation dynamics

Résumé: At least since the Great Depression, explaining why there are business fluctuations has been one of the biggest challenges that the science of economics has had to face. The hope is that if we could better understand recessions, then we could also be more successful in overcoming them. This dissertation consists of three papers that are part of the general endeavor of economists to understand these fluctuations. The first paper discusses, for a particular model, whether a result related to fluctuations would still hold if time were modeled as continuous rather than discrete. The two other papers focus on price stickiness. The second paper discusses why, after a large devaluation, prices of non-tradables may change by only a small amount in comparison to the magnitude of the devaluation. The third paper examines price adjustment in a model in which information is imperfect and it is costly to change prices.

Product Platform Development from the Product Lines' Perspective: Case of Switching Platform

In the era of fast product development and customized product requirements, the concept of product platform has proven its power in practice. The product platform approach has enabledcompanies to increase the speed of product introductions while simultaneously benefit from efficiency and effectiveness in the development and production activities. The product platforms are technological bases, which can be used to develop several derivative products, and hence, the differentiation can be pushed closer to the product introduction. The product platform development has some specific features, which differ somewhat from the product development of single products. The time horizon is longer, since the product platform¿slife cycle is longer than individual product's. The long time-horizon also proposes higher market risks and the use of new technologies increases the technological risks involved. The end-customer interface might be far away, but there is not a lack of needs aimed at the product platforms ¿ in fact, the product platform development is very much balancing between the varying needs set to it by thederivative products. This dissertation concentrated on product platform development from the internal product lines' perspective of a singlecase. Altogether six product platform development factors were identified: 'Strategic and business fit of product platform', 'Project communication and deliverables', 'Cooperation with product platform development', 'Innovativeness of product platform architecture and features', 'Reliability and quality of product platform', and 'Promised schedules and final product platform meeting the needs'. From the six factors, three were found to influence quite strongly the overall satisfaction, namely 'Strategic and business fit of product platform', 'Reliability and quality of product platform', and 'Promised schedules and final product platform meeting the needs'. Hence, these three factors might be the ones a new product platform development unit should concentrate first in order to satisfy their closest customers, the product lines. The 'Project communication and deliverables' and 'Innovativeness of product platform architecture and features' were weaker contributors to the overall satisfaction. Overall, the factors explained quite well the satisfaction of the product lines with product platform development. Along the research, several interesting aspects about the very basic nature of the product platform development were found. The long time horizon of the product platform development caused challenges in the area of strategic fIT - a conflict between the short-term requirements and long term needs. The fact that a product platform was used as basis of several derivative products resulted into varying needs, and hence the match with the needs and the strategies. The opinions, that the releases of the larger product lines were given higher priorities, give an interesting contribution to the strategy theory of powerand politics. The varying needs of the product lines, the strengths of them as well as large number of concurrent releases set requirements to prioritization. Hence, the research showed the complicated nature of the product platform development in the case unIT - the very basic nature of the product platform development might be its strength (gaining efficiency and effectiveness in product development and product launches) but also the biggest challenge (developing products to meet several needs). As a single case study, the results of this research are not directly generalizable to all the product platform development activities. Instead, the research serves best as a starting point for additional research as well as gives some insights about the factors and challengesof one product development unit.