High current-density anodic electro-dissolution in flow-injection systems for the determination of aluminium, copper and zinc in non-ferroalloys by flame atomic absorption spectrometry

An automatic Procedure with a high current-density anodic electrodissolution unit (HDAE) is proposed for the determination of aluminium, copper and zinc in non-ferroalloys by flame atonic absorption spectrometry, based on the direct solid analysis. It consists of solenoid valve-based commutation in a flow-injection system for on-line sample electro-dissolution and calibration with one multi-element standard, an electrolytic cell equipped with two electrodes (a silver needle acts as cathode, and sample as anode), and an intelligent unit. The latter is assembled in a PC-compatible microcomputer for instrument control, and far data acquisition and processing. General management of the process is achieved by use of software written in Pascal. Electrolyte compositions, flow rates, commutation times, applied current and electrolysis time mere investigated. A 0.5 mol l(-1) HNO3 solution was elected as electrolyte and 300 A/cm(2) as the continuous current pulse. The performance of the proposed system was evaluated by analysing aluminium in Al-allay samples, and copper/zinc in brass and bronze samples, respectively. The system handles about 50 samples per hour. Results are precise (R.S.D < 2%) and in agreement with those obtained by ICP-AES and spectrophotometry at a 95% confidence level.

Anti-inflammatory efficacy of a single posterior subtenon injection of triamcinolone acetonide versus prednisolone acetate 1% eyedrops after pars plana vitrectomy

Purpose: To compare the safety and anti-inflammatory efficacy of a single posterior subtenon injection of triamcinolone acetonide (TA) with prednisolone acetate 1% eyedrops after pars plana vitrectomy (PPV).Methods: the study included 40 consecutive phakic eyes of 40 patients undergoing PPV for non-clearing vitreous haemorrhage with attached retina (verified by echography), epiretinal membrane or macular hole. At the end of the surgical procedure, eyes were randomized to receive either a single posterior subtenon injection of TA (40 mg in 1 ml) plus sham eyedrops (prednisolone acetate 1% vehicle) postoperatively (group TA), or a posterior subtenon sham injection (1 ml balanced salt solution) plus prednisolone acetate 1% eyedrops postoperatively (group ED).Results: There was no difference in the severity of anterior chamber cell and flare between the two groups at any time-point during the study period (p > 0.05). Separate within-group analysis revealed a significant decrease in anterior chamber cell and flare from postoperative day 1 to postoperative days 7, 14 and 28 in both groups (p < 0.05). There was no difference in pain, photophobia, conjunctival erythema, ciliary flush or chemosis scores between the two groups at any time-point during the study period (p > 0.05). Steroid-induced intraocular hypertension was not observed in either group.Conclusions: A single posterior subtenon injection of TA can be as effective and safe as a 4-week regimen of prednisolone acetate 1% eyedrops in controlling intraocular inflammation after PPV.

Comparison of accuracy between compression- and injection-molded complete dentures

Statement of problem. A clinically significant incisal pin opening may occur after processing complete dentures if a compression molding technique is used. To recover the proper vertical dimension of occlusion, a time-consuming occlusal adjustment is necessary that often destroys the anatomy of the artificial teeth. A new injection molding process claims to produce dentures that require few, if any, occlusal adjustments in the laboratory after processing.Purpose. This laboratory study compared incisal pin opening, dimensional accuracy, and laboratory working time for dentures fabricated by this new injection system with dentures constructed by the conventional compression molding technique.Material and methods. Two groups of 6 maxillary and 6 mandibular dentures were evaluated as follows: group 1 (control), Lucitone 199, compression molded with a long cure cycle; and group 2, Lucitone 199, injection molded with a long cure. Incisal pin opening was measured with a micrometer immediately after deflasking. A computerized coordinate measuring machine was used to measure dimensional accuracy of 3-dimensional variations in selected positions of artificial teeth in 4 stages of denture fabrication. Analysis of variance (ANOVA) and t tests were performed to compare the groups.Results. A significant difference was found in pin opening between groups (t test). Horizontal dimensional changes evaluated with repeated measures ANOVA revealed no significant differences between groups. However, analysis of vertical dimensional changes disclosed significant differences between the groups. There was no appreciable difference in laboratory working time for flasking and molding denture bases between the injection and compression molding techniques when polymethyl methacrylate resin was used.Conclusion. The injection molding method produced a significantly smaller incisal pin opening over the standard compression molding technique. The injection molding technique, using polymethyl methacrylate, was a more accurate method for processing dentures. There were no appreciable differences in laboratory working time between the injection and compression molding techniques.

Theoretical analysis of aqueous residues incineration with oxygen enriched flames

The use of oxygen to enrich the oxidizer can be an attractive alternate to increase incineration rates of a combustion chamber originally designed to operate with air. For a certain fuel now rate, if some incineration parameters are held constant (as combustion chamber temperature, turbulence level, and residence time), an increase of incineration rates becomes possible with injection of oxygen. This work presents a theoretical evaluation of combustion air enrichment in a combustion chamber designed to incinerate aqueous residues using methane as fuel and air as oxidizer. Detailed chemistry was employed to predict pollutants formation. The overall process was investigated using the PSR routine from the CHEMKIN library. (C) 1999 Elsevier B.V. Ltd.

Analysis of the inflammatory reaction induced by the catfish (Cathorops spixii) venoms

Cathorops spixii is one of the most abundant venomous fish of the southeastern coast of the State of São Paulo, and consequently causes a great part of the accidents seen there. The accidents affect mainly fishermen, swimmers and tourists and are characterized by punctiform or wide wounds, erythema, edema, pain, sudoresis, indisposition, fever, nausea, vomiting and secondary infection. The objective of this work was to characterize the inflammatory response induced in mice by both venoms (mucus and sting) of the catfish C spixii. Our results demonstrated that both venoms induced a great number of rolling and adherent leukocytes in the post-capillary venules of cremaster muscle of mice, and an increase in the vascular permeability in peritoneal cavity. Mucus induced the recruitment of neutrophils immediately after injection followed later by macrophage infiltration. In contrast, the cellular infiltration elicited by sting venom was rapidly resolved. The peritonitis reaction provoked by venoms was characterized by cytokine (IL-6), chemokines (MCP-1 and KC) or lipid mediator (LTB4) production in the peritoneal cavity. The macrophages from 7-day mucus venom-induced exudates upon in vitro mucus venom stimulation, expressed CD1 Ic x MHC class II and release bioactive IL-12p70. on the other hand, sting venom-elicited peritoneal macrophages lost the ability to differentiate into dendritic cells, following re-stimulation in vitro with sting venom, they do not express CD11c, nor do they exhibit sufficient levels of MHC class II. In conclusion, both types of venoms (mucus or sting) promote inflammatory reaction with different profiles, and the inflammatory reaction induced by the first was characterized by antigen persistence in peritoneal cavity that allowed the activation of phagocytic cells with capacity of antigenic presentation. (C) 2007 Elsevier Ltd. All rights reserved.

On-line redox speciation analysis of antimony using L-proline immobilized on controlled pore glass and hydride generation inductively coupled plasma optical emission spectrometry for detection

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Ultrastructural analysis of bovine oocytes from ovarian follicles with different diameters

In vitro embryo production is an important technique for facilitating the reproduction of animals with high genetic merit. The greatest challenge for the reproducibility of this technique is the quality of the oocyte that is submitted for in vitro maturation. The aim of this work was to evaluate the ultrastructural characteristics of oocytes from follicles of different diameters using transmission electron microscopy. The animals were divided into 2 groups and were given a single i.m. injection of 250 IU FSH (Pluset, Serono, Italy). To synchronize the follicular growth, all follicles > 2 mm were aspirated during the estrous cycle, which was considered day zero (D0). Group 1 (G1; n = 4) received FSH on day 1 (D1), and the 2- to 5-mm follicles were aspirated on day 2 (D2). The animals in group 2 (G2; n = 5) received FSH on day 2 (D2), and their 10- to 15-mm follicles were aspirated on day 5 (D5). After aspiration, the oocytes from both groups were fixed and prepared for ultrastructural analysis. The oocytes analyzed from both groups had similar ultrastructural characteristics. The presence and distribution of organelles in the cytoplasm of the oocytes did not differ between groups, suggesting that, in relation to the ultrastructural characteristics, oocytes from 2 to 5 mm and 10 to 15 mm follicles are similar.

Ferroelectric SBN thin films grown by an SBN/Bi2O3 PLD sequential process

Ferroelectric SrBi2Nb2O9 (SBN) thin films were prepared by pulsed laser deposition (PLD) on Pt/Ti/SiO2/Si(100) using a sequential deposition process from two SBN and Bi2O3 targets. This route allows for bismuth enrichment of the film composition in order to improve the ferroelectric characteristics. Structural and microstructural characterizations were performed by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The composition of films and targets was determined by energy dispersive X-ray spectrometry (EDX). The deposition temperature, which provided well-crystallized layered perovskite SBN phase films in situ, was found to be 700°C. The results were compared with those obtained for SBN films deposited at 400°C and then crystallized ex situ. For an ex situ annealing temperature of 750°C, a remanent polarization value (Pr) of 23.2 μc/cm2 and a coercive field (Ec) of 112 kV/cm were measured. © 2001 Elsevier Science Ltd. All rights reserved.

Effects of long-term cyclosporin therapy on gingiva of rats--analysis by stereological and biochemical estimation.

Cyclosporin A (CsA) is used as an immunosuppressive agent and its prominent side effect is the induction of gingival overgrowth, which remains a significant problem. The risk factors appraised include the duration of treatment. However, there are no stereological and biochemical studies exploring the effects of long-term CsA therapy on gingival tissue. The purpose of the present study was to investigate the level of TGF-beta1 in saliva and describe the densities of fibroblasts and collagen fibers in the gingival tissue of rats treated with CsA for long periods. Rats were treated for 60, 120, 180 and 240 days with a daily subcutaneous injection of 10 mg/kg of body weight of CsA. At the end of the experimental periods, saliva was collected for the determination of TGF-beta1 levels. After histological processing, the oral epithelium and the connective tissue area were measured as well as the volume densities of fibroblasts (Vf) and collagen fibers (Vcf). After 60 and 120 days of CsA treatment, there was a significant increase in Vf and Vcf as well as a significant increase in TGF-beta1 levels. After 180 and 240 days, reduction in the gingival overgrowth associated with significant decreases in the level of TGF-beta1, and also decreased Vf and Vcf, were observed. The data presented here suggest that after long-term therapy, a decrease in TGF-beta1 levels occurs, which might contribute to an increase in the proteolytic activity of fibroblasts in the gingiva, favoring the normality of extracellular matrix synthesis.

GnRH agonist versus GnRH antagonist in poor ovarian responders: A meta-analysis

The aim of this meta-analysis was to compare the efficacy of gonadotrophin antagonist (GnRH-ant) versus GnRH agonist (GnRHa) as coadjuvant therapy for ovarian stimulation in poor ovarian responders in IVF/intracytoplasmic sperm injection cycles. Search strategies included on-line surveys of databases such as MEDLINE, EMBASE and others. A fixed effects model was used for odds ratio (OR) and effect size (weighted mean difference, WMD). Six trials fulfilled the inclusion criteria (randomized controlled trials). There was no difference between GnRH-ant and GnRHa (long and flare-up protocols) with respect to cycle cancellation rate, number of mature oocytes and clinical pregnancy rate per cycle initiated, per oocyte retrieval and per embryo transfer. When the mete-analysis was applied to the two trials that had used GnRH-ant versus long protocols of GnRHa, a significantly higher number of retrieved oocytes was observed in the GnRH-ant protocols [P = 0.018; WMD: 1.12 (0.18, 2.05)]. However, when the meta-analysis was applied to the four trials that had used GnRH-ant versus flare-up protocols, a significantly higher number of retrieved oocytes (P = 0.032; WMD: -0.51, 95% CI -0.99, -0.04) was observed in the GnRHa protocols. Nevertheless, additional randomized controlled trials with better planning are needed to confirm these results.

Reliability assessment of energy limited systems using sequential montecarlo simulation

This paper explains why the reliability assessment of energy limited systems requires more detailed models for primary generating resources availability, internal and external generating dispatch and customer demand than the ones commonly used for large power systems and presents a methodology based on the full sequential Montecarlo simulation technique with AC power flow for their long term reliability assessment which can properly include these detailed models. By means of a real example, it is shown how the simplified modeling traditionally used for large power systems leads to pessimistic predictions if it is applied to an energy limited system and also that it cannot predict all the load point adequacy problems. © 2006 IEEE.

Development and validation of HPLC method for quantitative analysis of triamcinolone in biodegradable microparticles

A simple, rapid, selective and specific high performance liquid chromatographic (HPLC) method for quantitative analysis of the triamcinolone in polylactide-co-glycolide acid (PLGA) microparticles was developed. The chromatographic parameters were reversed-phase C18 column, 250mm x 4.6mm, with particle size 5 μm. The column oven was thermostated at 35°C ± 2°C. The mobile phase was methanol/water 45:55 (v/v) and elution was isocratic at a flow-rate of 1 mL.mL-1. The determinations were performed using a UV-Vis detector at 239 nm. The injected sample volume was 10 μL. The standard curve was linear (r2 > 0.999) in the concentration range 100-2500 ng.mL-1. The method showed adequate precision, with a relative standard deviation (RSD) was smaller than 3%. The accuracy was analyzed by adding a standard drug and good recovery values were obtained for all drug concentrations used. The method showed specificity and selectivity with linearity in the working range and good precision and accuracy, making it very suitable for quantitation of triamcinolone in PLGA microparticles.

Recombinant LH supplementation to recombinant FSH during induced ovarian stimulation in the GnRH-antagonist protocol: A meta-analysis

This study aims to compare the efficacy of recombinant LH (rLH) supplementation for ovarian stimulation in gonadotrophin-releasing hormone-antagonist protocol for IVF/intracytoplasmic sperm injection cycles. Search strategies included online surveys of databases. The fixed effects model was used for odds ratio (OR) and effect size (weighted mean difference, WMD). Five trials fulfilled the inclusion criteria. When the meta-analysis was carried out, advantages were observed for the LH supplementation protocol with respect to higher serum oestradiol concentrations on the day of human chorionic gonadotrophin administration (P < 0.0001; WMD: 514, 95% CI 368, 660) and higher number of mature oocytes (P = 0.0098; WMD: 0.88, 95% CI 0.21, 1.54). However, these differences were not observed in the total amount of recombinant FSH (rFSH) administered, days of stimulation, number of oocytes retrieved, the clinical pregnancy rate per oocyte retrieval, the implantation rate and miscarriage rate. This result demonstrates that the association of rLH with rFSH may prevent any decrease in oestradiol after antagonist administration and that a significantly higher number of mature oocytes was available for laboratory work. Nevertheless, it failed to show any statistically significant difference in clinically significant end-points in IVF (implantation and pregnancy rates). Additional randomized controlled trials are needed to confirm these results further. © 2007 Published by Reproductive Healthcare Ltd.

Slurry sample injection for determination of ferrite nanocolloids chemical composition by ICP spectrometry

This work proposes a new method to determine the chemical composition of magnetic ferrite nanoparticles by the slurry injection technique using the inductively coupled plasma optical emission spectroscopy. In this way, experimental conditions such as aerosol gas flow rate and colloidal stability were optimized in order to use aqueous calibration curves in the slurry nebulization and to determine the chemical composition of a series of sols containing chemically synthesized size-tailored NiFe 2O 4 nanograms. Then, the results of direct sampling and those of conventional aqueous introduction analysis are compared, showing the efficiency of the proposed method.

Experimental analysis and adherence test of the electromagnetic zero-sequence blocking model

This paper reveals new contributions to the analysis and development of mitigating harmonic distortion devices. Considering the variety of sequential distribution of harmonic current, in the use of passive filters, one can point out the electromagnetic blocking device, which have received particular attention due to its robustness and low cost of installation. In this context, aiming the evaluation of the reliability of the results obtained through mathematical modeling, experimental tests are carried out using a low-power prototype, highlighting particular aspects related to its function as a zero-sequence harmonic blocking. © 2011 IEEE.