Investigations on the influence of graphite filler on dry sliding wear and abrasive wear behaviour of carbon fabric reinforced epoxy composites

In this experimental study, the dry sliding wear and two-body abrasive wear behaviour of graphite filled carbon fabric reinforced epoxy composites were investigated. Carbon fabric reinforced epoxy composite was used as a reference material. Sliding wear experiments were conducted using a pin-on-disc wear tester under dry contact condition. Mass loss was determined as a function of sliding velocity for loads of 25, 50, 75, and 100 N at a constant sliding distance of 6000 m. Two-body abrasive wear experiments were performed under multi-pass condition using silicon carbide (SiC) of 150 and 320 grit abrasive papers. The effects of abrading distance and different loads have been studied. Abrasive wear volume and specific wear rate as a function of applied normal load and abrading distance were also determined. The results show that in dry sliding wear situations, for increased load and sliding velocity, higher wear loss was recorded. The excellent wear characteristics were obtained with carbon-epoxy containing graphite as filler. Especially, 10 wt.% of graphite in carbon-epoxy gave a low wear rate. A graphite surface film formed on the counterface was confirmed to be effective in improving the wear characteristics of graphite filled carbon-epoxy composites. In case of two-body abrasive wear, the wear volume increases with increasing load/abrading distance. Experimental results showed the type of counterface (hardened steel disc and SiC paper) material greatly influences the wear behaviour of the composites. Wear mechanisms of the composites were investigated using scanning electron microscopy. Wear of carbon-epoxy composite was found to be mainly due to a microcracking and fiber fracture mechanisms. It was found that the microcracking mechanism had been caused by progressive surface damage. Further, it was also noticed that carbon-epoxy composite wear is reduced to a greater extent by addition of the graphite filler, in which wear was dominated by microplowing/microcutting mechanisms instead of microcracking.

The effects of manganese content and mould size on abrasion and slurry erosion behaviour of chromium-manganese iron systems investigated by positron lifetime spectroscopy

Abrasion and slurry erosion behaviour of chromium-manganese iron samples with chromium (Cr) in the range similar to 16-19% and manganese (Mn) at 5 and 10% levels have been characterized for hardness followed by microstructural examination using optical and scanning electron microscopy. Positron lifetime studies have been conducted to understand the defects/microporosity influence on the microstructure. The samples were heat treated and characterized to understand the structural transformations in the matrix. The data reveals that hardness decreased with increase in Mn content from 5 to 10% in the first instance and then increase in the section size in the other case, irrespective of the sample conditions. The abrasion and slurry erosion losses show increase with increase in the section size as well as with increase in Mn content. The positron results show that as hardness increases from as-cast to heat treated sample, the positron trapping rate and hence defect concentration showed opposite trend as expected. So a good correlation between defects concentration and the hardness has been observed. These findings also corroborate well with the microstructural features obtained from optical and scanning electron microscopy. (C) 2009 Elsevier B. V. All rights reserved.

Interrupted creep behaviour of Mg alloys developed for powertrain applications

A conventional magnesium alloy, AZ91D, and two creep resistant magnesium alloys, developed for powertrain applications, MRI 153M and MRI 230D, are prepared by high pressure die casting. These alloys are tested for their creep behaviour in the continuous manner, as is the Current practice, and in the interrupted manner, which represents the real life Situation more closely. It is observed that the interrupted creep tests give rise to a primary creep appearing at the beginning of each cycle resulting in a higher average strain rate than that encountered in the continuous creep tests. Further, the shorter the cycle time, higher is the average strain rate in the interrupted creep tests. A higher average strain rate will give rise to a higher strain over the same period. This is attributed to the recovery taking place during the cooling and heating between two cycles. The effect of additional precipitation during interrupted creep tests depends on the nature of the precipitates. The additional precipitation of beta phase during the cooling and heating between two cycles increases the steady state strain rate in the AZ91D and MRI 153M alloys. whereas the additional precipitation of C36 phase during the cooling and heating between two cycles decreases the steady state strain rate in the MRI 230D alloy. (C) 2009 Elsevier B.V. All rights reserved.

On the behaviour of some physical parameterization methods in high-resolution numerical weather prediction models

Modern-day weather forecasting is highly dependent on Numerical Weather Prediction (NWP) models as the main data source. The evolving state of the atmosphere with time can be numerically predicted by solving a set of hydrodynamic equations, if the initial state is known. However, such a modelling approach always contains approximations that by and large depend on the purpose of use and resolution of the models. Present-day NWP systems operate with horizontal model resolutions in the range from about 40 km to 10 km. Recently, the aim has been to reach operationally to scales of 1 4 km. This requires less approximations in the model equations, more complex treatment of physical processes and, furthermore, more computing power. This thesis concentrates on the physical parameterization methods used in high-resolution NWP models. The main emphasis is on the validation of the grid-size-dependent convection parameterization in the High Resolution Limited Area Model (HIRLAM) and on a comprehensive intercomparison of radiative-flux parameterizations. In addition, the problems related to wind prediction near the coastline are addressed with high-resolution meso-scale models. The grid-size-dependent convection parameterization is clearly beneficial for NWP models operating with a dense grid. Results show that the current convection scheme in HIRLAM is still applicable down to a 5.6 km grid size. However, with further improved model resolution, the tendency of the model to overestimate strong precipitation intensities increases in all the experiment runs. For the clear-sky longwave radiation parameterization, schemes used in NWP-models provide much better results in comparison with simple empirical schemes. On the other hand, for the shortwave part of the spectrum, the empirical schemes are more competitive for producing fairly accurate surface fluxes. Overall, even the complex radiation parameterization schemes used in NWP-models seem to be slightly too transparent for both long- and shortwave radiation in clear-sky conditions. For cloudy conditions, simple cloud correction functions are tested. In case of longwave radiation, the empirical cloud correction methods provide rather accurate results, whereas for shortwave radiation the benefit is only marginal. Idealised high-resolution two-dimensional meso-scale model experiments suggest that the reason for the observed formation of the afternoon low level jet (LLJ) over the Gulf of Finland is an inertial oscillation mechanism, when the large-scale flow is from the south-east or west directions. The LLJ is further enhanced by the sea-breeze circulation. A three-dimensional HIRLAM experiment, with a 7.7 km grid size, is able to generate a similar LLJ flow structure as suggested by the 2D-experiments and observations. It is also pointed out that improved model resolution does not necessary lead to better wind forecasts in the statistical sense. In nested systems, the quality of the large-scale host model is really important, especially if the inner meso-scale model domain is small.

The effect of ageing on microstructure and nanoindentation behaviour of dc magnetron sputter deposited nickel rich NiTi films

Nickel rich NiTi films were sputter deposited on p-doped Si left angle bracket1 0 0right-pointing angle bracket substrates maintained at 300 °C. The films were subsequently solution treated at 700 °C for 30 min followed by ageing at 400 and 500 °C for 5 h. The microstructure of the films was examined by TEM and these studies revealed that the NiTi films were mostly amorphous in the as-deposited condition. The subsequent solution treatment and ageing resulted in crystallization of the films with the film aged at 400 °C exhibiting nanocrystalline grains and three phases viz. B2 (austenite), R and Ni3Ti2 whereas the film aged at 500 °C shows micron sized grains and two phases viz. R and Ni3Ti2. Nanoindentation studies revealed that the nature of the load versus indentation depth response for the films aged at 400 and 500 °C was different. For the same load, the indenter penetrated to a much greater depth for the film aged at 400 °C as compared to the film aged at 500 °C. Also the ratio of the residual indentation depth (hf) to maximum indentation depth (hmax) is lower for the film aged at 400 °C as compared to the film aged at 500 °C. This was attributed to the occurrence of stress induced martensitic transformation of the B2 phase present in the film aged at 400 °C during indentation loading which results in a transformation strain in addition to the normal elastic and plastic strains and its subsequent recovery on unloading. The hardness and elastic modulus measured using the Oliver and Pharr analysis was also found to be lower for the film aged at 400 °C as compared to the film aged at 500 °C which was also primarily attributed to the same effect.

Selective attention in a synchronising bushcricket: physiology, behaviour and ecology

Synchronising bushcricket males achieve synchrony by delaying their chirps in response to calling neighbours. In multi-male choruses, males that delay chirps in response to all their neighbours would remain silent most of the time and be unable to attract mates. This problem could be overcome if the afferent auditory system exhibited selective attention, and thus a male interacted only with a subset of neighbours. We investigated whether individuals of the bushcricket genus Mecopoda restricted their attention to louder chirps neurophysiologically, behaviourally and through spacing. We found that louder leading chirps were preferentially represented in the omega neuron but the representation of softer following chirps was not completely abolished. Following chirps that were 20 dB louder than leading chirps were better represented than leading chirps. During acoustic interactions, males synchronised with leading chirps even when the following chirps were 20 dB louder. Males did not restrict their attention to louder chirps during interactions but were affected by all chirps above a particular threshold. In the field, we found that males on average had only one or two neighbours whose calls were above this threshold. Selective attention is thus achieved in this bushcricket through spacing rather than neurophysiological filtering of softer signals.

Studies on the ignition behaviour of boron powder

The ignition behaviour of boron powder, prepared through electrowinning process, was studied by using thermogravimetry coupled with simultaneous differential thermal analysis (TG-SDTA). The dependence of the inception of the ignition reaction on the partial pressure of oxygen, particle size of the boron powder and heating rate was investigated. It was observed that all these factors affect the ignition temperature. Boron powder with a mean particle size of about 10 mu m was found to be susceptible to ignition in oxygen even at 783K. In general, the susceptibility to ignition was found to vary inversely with the degree of crystallinity. Presence of carbon was found to retard the oxidation of boron and raise the ignition temperature. These results are useful in safe handling and storage of finely divided boron powder and in the subsequent production of boron carbide from it. (C) 2009 Elsevier B.V. All rights reserved.

Diet and physical activity behaviour in nurses: A qualitative study

Issue addressed: Previous research has shown that approximately 60% of nurses in Australia are overweight or obese, insufficiently active and have an unhealthy diet. The aim of this study was to gain an understanding of nurses’ determinants contributing to these behaviours. This will inform a needs assessment for a future workplace health promotion program (WHPP) in this group. Methods: Four focus group discussions (n = 17) were conducted with a convenience sample of nurses aged 25–59 years from three hospitals in the Brisbane metropolitan area. Questions addressed barriers and motivation towards diet and physical activity (PA), and suggestions for future WHPP. Data were analysed with Nvivo10 following a thematic analysis with a realistic approach using Self-determination theory as a framework. Results: Work environment was the main barrier for healthy diet behaviours. Long working hours and lack of breaks challenged nurses’ self-control and self-regulation when making dietary choices. Fatigue was the main barrier for PA. However, relaxation, feeling energised before work and better sleep after working night shifts motivated nurses to do PA. Social environment at work seemed to be an effective external motivation to encourage healthy diet and regular PA. Goal-setting, self-monitoring and social support at work were identified as potential WHHP strategies. Conclusion: The workplace and job demands negatively impacts nurses’ lifestyle behaviours. Future interventions should include social support from colleagues, which could motivate nurses to make healthier food choices at work and be more active outside work.

Selective attention in a synchronising bushcricket: physiology, behaviour and ecology

Synchronising bushcricket males achieve synchrony by delaying their chirps in response to calling neighbours. In multi-male choruses, males that delay chirps in response to all their neighbours would remain silent most of the time and be unable to attract mates. This problem could be overcome if the afferent auditory system exhibited selective attention, and thus a male interacted only with a subset of neighbours. We investigated whether individuals of the bushcricket genus Mecopoda restricted their attention to louder chirps neurophysiologically, behaviourally and through spacing. We found that louder leading chirps were preferentially represented in the omega neuron but the representation of softer following chirps was not completely abolished. Following chirps that were 20 dB louder than leading chirps were better represented than leading chirps. During acoustic interactions, males synchronised with leading chirps even when the following chirps were 20 dB louder. Males did not restrict their attention to louder chirps during interactions but were affected by all chirps above a particular threshold. In the field, we found that males on average had only one or two neighbours whose calls were above this threshold. Selective attention is thus achieved in this bushcricket through spacing rather than neurophysiological filtering of softer signals.

Volume change behaviour of fine grained solis

Soils in and and semi-arid zones undergoes volume changes due to wetting. Depending upon the type of clay minerals present, degree of saturation, externally applied load and bonding, the fine grained soils either swells or compresses. One of the parameter that affects the volume change behaviour is the primary clay mineral present in their clay size fraction. A simple method of identifying the same has been presented. It has been brought out that in an expansive unsaturated undisturbed soil, the diffuse double layer repulsion, the stress state and the bonding play significant role in their volume change behaviour. In non-expansive fine grained unsaturated undisturbed soils, the shearing resistance at particle level (including the matrix suction and bonding) and fabric play a significant role in influencing the volume change behaviour. While both the mechanism co-exist, one of them play a dominant role depending upon the primary clay mineral is swelling or non swelling.

Pathways to health : Determinants of health, health behaviour and health inequalities in early adulthood

There is increasing evidence that the origins of poor adult health and health inequalities can be traced back to circumstances preceding current socioeconomic position and living conditions. The life-course approach to examining the determinants of health has emphasised that exposure to adverse social and economic circumstances in earlier life or concurrent adverse circumstances due to unfavourable living conditions in earlier life may lead to poor health, health-damaging behaviour, disease or even premature death in adulthood. There is, however, still a lack of knowledge about the contribution of social and economic circumstances in childhood and youth to adult health and health inequalities, and even less is known about how environmental and behavioural factors in adulthood mediate the effects of earlier adverse experiences. The main purpose of this study was to deepen our understanding of the development of poor health, health-damaging behaviours and health inequalities during the life-course. Its aim was to find out which factors in earlier and current circumstances determine health, the most detrimental indicators of health behaviour (smoking, heavy drinking and obesity as a proxy for the balance between nutrition and exercise), and educational health differences in young adults in Finland. Following the ideas of the social pathway theory, it was assumed that childhood environment affects adult health and its proximal determinants via different pathways, including educational, work and family careers. Early adulthood was studied as a significant phase of life when many behavioural patterns and living conditions relevant to health are established. In addition, socioeconomic health inequalities seem to emerge rapidly when moving into adulthood; they are very small or non-existent in childhood and adolescence, but very marked by early middle age. The data of this study were collected in 2000 2001 as part of the Health 2000 Survey (N = 9,922), a cross-sectional and nationally representative health interview and examination survey. The main subset of data used in this thesis was the one comprising the age group 18 29 years (N = 1,894), which included information collected by standardised structured computer-aided interviews and self-administered questionnaires. The survey had a very high participation rate at almost 90% for the core questions. According to the results of this study, childhood circumstances predict the health of young adults. Almost all the childhood adversities studied were found to be associated with poor self-rated health and psychological distress in early adulthood, although fewer associations were found with the somatic morbidity typical of young adults. These effects seemed to be more or less independent of the young adult s own education. Childhood circumstances also had a strong effect on smoking and heavy drinking, although current circumstances and education in particular, played a role in mediating this effect. Parental smoking and alcohol abuse had an influence on the corresponding behaviours of offspring. Childhood circumstances had a role in the development of obesity and, to a lesser extent, overweight, particularly in women. The findings support the notion that parental education has a strong effect on early adult obesity, even independently of the young adult s own educational level. There were marked educational differences in self-rated health in early adulthood: those in the lowest educational category were most likely to have average or poorer health. Childhood social circumstances seemed to explain a substantial part of these educational differences. In addition, daily smoking and heavy drinking contributed substantially to educational health differences. However, the contribution of childhood circumstances was largely shared with health behaviours adopted by early adulthood. Employment also shared the effects of childhood circumstances on educational health differences. The results indicate that childhood circumstances are important in determining health, health behaviour and health inequalities in early adulthood. Early recognition of childhood adversities followed by relevant support measures may play an important role in preventing the unfortunate pathways leading to the development of poor health, health-damaging behaviour and health inequalities. It is crucially important to recognise the needs of children living in adverse circumstances as well as children of substance abusing parents. In addition, single-parent families would benefit from support. Differences in health and health behaviours between different sub-groups of the population mean that we can expect to see ever greater health differences when today s generation of young adults grows older. This presents a formidable challenge to national health and social policy as well as health promotion. Young adults with no more than primary level education are at greatest risk of poor health. Preventive policies should emphasise the role of low educational level as a key determinant of health-damaging behaviours and poor health. Keywords: health, health behaviour, health inequalities, life-course, socioeconomic position, education, childhood circumstances, self-rated health, psychological distress, somatic morbidity, smoking, heavy drinking, BMI, early adulthood

Studies of the polarographic and coulometric behaviour of aromatic nitro-compounds: I. Nitrobenzene in ethanol

A detailed polarographic (a.c. and d.c.) and coulometric investigation of nitrobenzene has been made at various pH values in the presence of different concentrations of ethanol. Below pH 4.7, two waves are apparent but above this pH, the second wave does not appear. Coulometric evidence indicates that the first and second waves correspond to the four-and two-electron processes, respectively. The coulometric method was not applicable in sodium hydroxide and sodium acetate solutions. When the diffusion coefficients (from the diaphragm cell) are used in the Ilkovic equation, no reliable conclusions can be reached for the number of electrons involved in the reduction process in alkaline solutions. The a.c. polarographic method gives evidence for the formation of species such as: C6H5NO2H22+, C6H5NO2− and C6H5NO22−. Analysis of d.c. polarographic data by Delahay's treatment of irreversible waves, indicates that the number of electrons involved in the rate-determining step is 2. In sodium hydroxide solutions, however, the first main wave is split indicating more than one rate-determining step. The results presented in this paper indicate that the first wave in the reduction of nitrobenzene is a four-electron process at all pH values. The second wave, which appears below pH 4.7, corresponds to a two-electron process irrespective of wave heights. The difference in the a.c. polarographic behaviour in acid and alkaline solutions has given evidence for the formation of species like C6H5NO2H2, C6H5NO2−, and C6H5NO22.

Note: Creep behaviour of high density polyethylene

The Ramberg-Osgood type constitutive law for creep suggested by Iyengar2 has been verified on high-density polyethylene. The time functions are evaluated from the experimental data of Scheweiker and Sidebottom3. It is found that the creep behaviour of the above material can be represented by the Ramberg-Osgood type law.

Creep behaviour of nimonic and R.R. 59 alloys

The Ramberg-Osgood relation which adequately describes the stress-strain curve of a strain-hardening material is extended to formulate the constitutive laws for creep. The constitutive laws which describe primary creep adequately are extended to secondary creep. The results are verified for the case of R.R. 59 at 200°C, Nimonic 80A and Nimonic 90 alloys at 750°C.